PRODUCT MODEL NUMBERS
MVWB750Y, MVWB800Y, MVWB850Y, MVWB950Y,
MVWB880B, MVWB980B
Top Loading Washer
Spacing for recessed area or closet installation
All dimensions show recommended spacing allowed, with tested spacing of 0" (0 mm) clearance on sides.
■ Additional spacing should be considered for ease of installation and servicing.
■ Additional clearances might be required for wall, door, and oor moldings.
■ Additional spacing should be considered on all sides of the washer to reduce noise transfer.
■ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are
required. Louvered doors with equivalent ventilation openings are acceptable.
■ Companion appliance spacing should also be considered.
Spacing for recessed area or closet installation
Washer Dimensions:
45.5"
(1156 mm)
27.5"
(698 mm)
27.5"
(698 mm)
17"
(432 mm)
5"
(126 mm)
14" max.
(356 mm)
3"
(76 mm)
3"
(76 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
1"
(25 mm)
1"
(25 mm)
W10410358C
08/2013
Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is
recommended that a separate circuit serving only this appliance be provided.
DRAIN SYSTEM
Drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub. Select method you need.
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.4 m) from bottom of washer. If you must install higher than 96"
(2.4 m), you will need a sump pump system.
Wall standpipe drain system
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at
least 39" (990 mm) above oor; install no higher than 96" (2.4 m)
from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 4
1
⁄2" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with cable tie.
Floor drain system
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please see toll-free phone
numbers in your “Use and Care Guide.” Minimum siphon break:
28" (710 mm) from bottom of washer. (Additional hoses may
be needed.)
Floor standpipe drain system
39"
(990 mm)
4
1
/2"
(114 mm)
4
1
/2"
(114 mm)
4
1
/2"
(114 mm)
30"
(762 mm)
39"
(990 mm)
See requirements for oor standpipe drain system.
-
1
-
2
Maytag MVWB850Y User manual
- Category
- Washing machines
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Maytag MVWB700V Product Dimensions
-
-
Whirlpool WTW8900BC Owner's manual
-
-
Whirlpool MVWB750YW0 Installation guide
-
-
-
Maytag MVWB850WQ - Bravos 5.0 cu. Ft. IEC Capacity Washer Installation Instructions Manual
-
-