Cisco CATALYST MEM-C6K-FLC24M User manual

Brand: Cisco

Model: CATALYST MEM-C6K-FLC24M

Category: Notebooks

Type: User manual

This manual is also suitable for

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Catalyst 6500 Series Supervisor Engine Flash PC

Card Installation Note

Product Numbers:

MEM-C6K-FLC16M(=)

MEM-C6K-FLC24M(=)

MEM-C6K-FLC64M(=)

MEM-C6K-ATA-1-64M(=)

This installation note contains the procedure to install a Flash PC card in the Catalyst 6500 series

supervisor engines.

Note The 64-MB ATA Flash PC card (MEM-C6K-ATA-1-64M) requires Supervisor Engine 2 with ROMMON

software release 7.1(1) or later releases. For ROMMON software upgrade details, refer to

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/78_13488.htm.

The ATA Flash PC card is supported on Catalyst 6500 series switches running Cisco IOS Release

12.1(8a)EX or later releases on both the supervisor engine and the Multilayer Switch Feature Card

(MSFC).

The ATA Flash PC card is supported on Catalyst 6500 series switches running Catalyst software

release 7.5(1) or later releases on the supervisor engine and Cisco IOS on the MSFC.

Note The 64-MB linear Flash PC card (MEM-C6K-FLC64M) is supported only on Supervisor Engine 1 and

requires ROMMON software release 5.3(1) or later releases.

The 64-MB linear Flash PC card is supported on Catalyst 6500 series switches running Cisco IOS

Release 12.1(13)E4 or later releases on both the supervisor engine and the MSFC.

The 64-MB linearFlashPCcardis supported on Catalyst 6500 series switches running Catalyst software

release 7.5(1) or later releases on the supervisor engine and Cisco IOS software on the MSFC.

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Contents

This installation note contains the following sections:

• Supervisor Engine Flash PC Cards, page 2

• Preventing Electrostatic Discharge Damage, page 3

• Installing and Removing a Flash PC Card, page 3

• Using Flash PC Cards, page 6

• Additional Documentation, page 8

• Obtaining Documentation, page 8

• Documentation Feedback, page 9

• Cisco Product Security Overview, page 9

• Obtaining Technical Assistance, page 10

• Obtaining Additional Publications and Information, page 12

Supervisor Engine Flash PC Cards

The supervisor engine Flash PC cards conform with the PCMCIA format. These models are available:

• 16-MB MEM-C6K-FLC16M

• 24-MB MEM-C6K-FLC24M

• 64-MB MEM-C6K-FLC64M

• MEM-C6K-ATA-1-64M

Note The 16-MB MEM-C6K-FLC16M and 24-MB MEM-C6K-FLC24M linear Flash PC cards are formatted

for the Catalyst 6500 series supervisor engines and are ready to use.

The MEM-C6K-ATA-1-64M and 64-MB MEM-C6K-FLC64M Flash PC cards are not formatted. You

must format these cards (See Table 1 on page 7Commands for Using and Managing FlashDevicesTable 1for

a description of the format command.) When you enter the dir disk0: or dir slot0: commands, an

unformatted Flash PC card returns a “bad device block info” or “invalid magic number” error message.

Note Supervisor Engine 1 and Supervisor Engine 2 do not support the same Flash PC card format. To use a

Flash PC card with Supervisor Engine 2, you must format the card with Supervisor Engine 2. To use a

Flash PC card with Supervisor Engine 1, you must format the card with Supervisor Engine 1.

You can use Flash PC cards to store and boot software images, or they can be used as servers to store

software images for other systems. You can configure each supervisor engine with one Flash PC card in

slot 0. Figure 1 shows the front panel of a supervisor engine with the single PCMCIA slot, slot 0.

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Preventing Electrostatic Discharge Damage

Figure 1 Supervisor Engine Flash PC Card Slot

For information about using the PCMCIA Flash PC cards, see the “Using Flash PC Cards” section on

page 6.

Preventing Electrostatic Discharge Damage

Follow these guidelines to prevent electrostatic discharge (ESD) damage:

• Always use an ESD wrist or ankle strap, and ensure that it makes good skin contact.

• Connect the equipment end of the strap to the ESD connector on the switch.

• Place a removed Flash PC card on an antistatic surface or in a static shielding bag. If the card will

be returned to the factory, immediately place it in a static shielding bag.

• Avoid contact between the card and clothing. The wrist strap only protects the card from ESD

voltages on the body; ESD voltages on clothing can still cause damage.

Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be

between 1 and 10 megohms.

Installing and Removing a Flash PC Card

Before you install a Flash PC card, verify that the card’s write-protect switch is off. When the card is

oriented with the printing side up and the edge connector end away from you, the write-protect switch

is located on the front edge of the card, as shown in Figure 2.

Note Not all Flash PC cards have the write-protect switch.

16057

SUPERVISOR I

WS-X6K-SUP1

STATUS

SYSTEM

ACTIVE

PWR MGMT

RESET

CONSOLE

Switch Load

100%

CONSOLE

PORT

MODE

PCMCIA EJECT

PORT 1

LINK

PORT 2

LINK

PCMCIA LED LINK LEDs

Switch load

display

Status LEDs

RESET button

CONSOLE port

CONSOLE PORT MODE

switch

PCMCIA slot 1000BASE-X GBIC Uplink Ports

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Installing and Removing a Flash PC Card

Figure 2 Locating the Flash PC Card Write Protection Switch

To install and remove a Flash PC card (see Figure 3), perform these steps:

Note You can insert and remove the Flash PC card with the power on.

Step 1 Connect an ESD-preventive strap to the ESD connector on the switch.

Step 2 Face the front panel of the switch, and hold the Flash PC card with the connector end toward the slot, as

shown in Figure 3a.

Step 3 Insert the card into the slot until it completely seats in the connector at the back of the slot and the eject

button pops out toward you, as shown in Figure 3b.

Note The card does not insert all the way inside the slot; a portion of the card remains outside the slot.

Do not attempt to force the card past this point.

Step 4 To eject a Flash PC card, press the ejector button until the card is free of the connector at the back of the

slot, as shown in Figure 3c.

Step 5 Remove the card from the slot and place it in an antistatic bag.

Flash PC card

write protection

Flash PC card

shown with write

protection off

H2352

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Installing and Removing a Flash PC Card

Figure 3 Installing and Removing a Flash PC Card

14233

Switch Load

PCMCIA EJECT

100%

CONSOLE AUX

RESET

FAN

SLOT 1

SLOT 0

ACTIVE

PS1

PS2

SUPERVISOR ENGINE I I I

WS-X5530

SYSTEM

STATUS

Switch Load

PCMCIA EJECT

100%

CONSOLE AUX

RESET

FAN

SLOT 1

SLOT 0

ACTIVE

PS1

PS2

SUPERVISOR ENGINE I I I

WS-X5530

SYSTEM

STATUS

Switch Load

PCMCIA EJECT

100%

CONSOLE AUX

RESET

FAN

SLOT 1

SLOT 0

ACTIVE

PS1

PS2

SUPERVISOR ENGINE I I I

WS-X5530

SYSTEM

STATUS

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Using Flash PC Cards

Note An MS-DOS formatted ATA Flash PC card or linear Flash PC card can be accessed successfully

(including the dir command) with the Catalyst and Cisco IOS operating systems but will not boot from

ROMMON.

Note The 16-MB MEM-C6K-FLC16M and 24-MB MEM-C6K-FLC24M linear Flash PC cards are formatted

for the Catalyst 6500 series supervisor engines and are ready to use.

The MEM-C6K-ATA-1-64M and 64-MB MEM-C6K-FLC64M Flash PC cards are not formatted. You

must format these cards (see Table 1 on page 7 for a description of the format command.) When you enter

the dir disk0: or dir slot0: commands, an unformatted Flash PC card returns a “bad device block info” or

“invalid magic number” error message.

Note Supervisor Engine 1 and Supervisor Engine 2 do not support the same Flash PC card format. To use a

Flash PC card with Supervisor Engine 2, you must format the card with Supervisor Engine 2. To use a

Flash PC card with Supervisor Engine 1, you must format the card with Supervisor Engine 1.

Table 1 Table 1Table 1Table 1shows many of the commands that are available for using and managing

Flash devices, including the Flash PC cards. To perform specific tasks, use these commands either alone

or combined with other commands. For example, to copy a file from a TFTP server to a Flash PC card,

set the BOOT environment variable so that the system will boot from this new image and then verify the

boot sequence as shown in the following steps:

Note The following commands listed in Table 1 are not applicable to the ATA Flash (disk0:) PC card:

undelete, squeeze, show flash devices, show flash, and verify.

Note The ATA Flash PC card is accessed through disk0: and the 16-MB, 24-MB, and 64-MB Flash PC cards

are accessed through slot0:. The following procedure uses slot0:.

Step 1 Copy a file from a TFTP server to the Flash PC card in slot0:

Console (enable) copy tftp slot0:

Step 2 Set the BOOT environment variable so that the system boots from slot0:

Console (enable) set boot system flash slot0:cat6000-sup-5-1-1-CSX.bin prepend

Step 3 Display the contents of the BOOT environment variable:

Console (enable) show boot

For complete descriptions of these commands and how to use them, refer to the Catalyst 6500 Series

Software Configuration Guide and the Catalyst 6500 Series Command Reference publication.

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Using Flash PC Cards

Table 1 Commands for Using and Managing Flash Devices

Task Command

Copy a Flash ﬁle to a TFTPserver, another

Flash device, or to the running

conﬁguration.

copy m/device:ﬁlename {tftp | ﬂash | m/device:ﬁlename |

conﬁg}

Copy a ﬁle from a TFTP server to a Flash

device or to the running conﬁguration.

copy tftp {ﬂash | m/device:ﬁlename | conﬁg}

Copy a ﬁle from Flash memory to a TFTP

server or to a Flash device, or to the

running conﬁguration.

copy ﬂash {tftp | m/device:ﬁlename | conﬁg}

Copy the running conﬁguration to another

Flash device or to a TFTP server.

copy conﬁg {ﬂash | m/device:ﬁlename | tftp}

Set the BOOT environment variable. set boot system ﬂash device:[ﬁlename] [prepend]

[mod_num]

Format a Flash PC device. format [spare spare-number] [m/]device1: [[device2:]

[monlib-ﬁlename]]

Specify the boot ﬁeld in the conﬁguration

method the switch will use at the next

startup.

set boot conﬁg-register boot {rommon | bootﬂash |

system} [mod_num]

Display the contents of the BOOT

environment variable.

show boot [mod_num]

Clear a speciﬁc image from the BOOT

environment variable.

clear boot system ﬂash device:[ﬁlename] [mod_num]

Clear the entire BOOT environment

variable.

clear boot system all [mod_num]

Display a list of ﬁles on a Flash device. dir [[m/]device:][ﬁlename] [all | deleted | long]

Set the default Flash device for the system. cd [[m/][bootﬂash: | slot0:]]

Verify the default Flash device for the

system.

pwd [mod_num]

Delete a ﬁle on a Flash device. delete [[m/]device:]ﬁlename

Undelete a ﬁle on a Flash device. undelete index [[m/]device:]

Permanently remove all deleted ﬁles on a

Flash device.

squeeze [m/]device:

Identify the supported Flash devices on the

system.

show ﬂash devices

Display information about the Flash PC. show ﬂash [[m/]device:] [all | chips | ﬁlesys]

Verify the checksum of a ﬁle on a Flash

device.

verify [[m/]device:] ﬁlename

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Additional Documentation

Refer to the following documents for additional information on supervisor engine Flash devices:

• Release Notes for Catalyst 6500 Series and Cisco 7600 Series Internet Router Supervisor

Engine 2 ROMMON

• Catalyst 6500 Series Software Configuration Guide

• Catalyst 6500 Series Command Reference

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several

ways to obtain technical assistance and other technical resources. These sections explain how to obtain

technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/techsupport

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Product Documentation DVD

Cisco documentation and additional literature are available in the Product Documentation DVD package,

which may have shipped with your product. The Product Documentation DVD is updated regularly and

may be more current than printed documentation.

The Product Documentation DVD is a comprehensive library of technical product documentation on

portable media. The DVD enables you to access multiple versions of hardware and software installation,

configuration, and command guides for Cisco products and to view technical documentation in HTML.

With the DVD, you have access to the same documentation that is found on the Cisco website without

being connected to the Internet. Certain products also have .pdf versions of the documentation available.

The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com

users (Cisco direct customers) can order a Product Documentation DVD (product number

DOC-DOCDVD=) from Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Documentation Feedback

Ordering Documentation

Beginning June 30, 2005, registered Cisco.com users may order Cisco documentation at the Product

Documentation Store in the Cisco Marketplace at this URL:

http://www.cisco.com/go/marketplace/

Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m.

(0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by

calling 011 408 519-5055. You can also order documentation by e-mail at

[email protected] or by fax at 1 408 519-5001 in the United States and Canada,

or elsewhere at 011 408 519-5001.

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by completing the online feedback

form that appears with the technical documents on Cisco.com.

You can send comments about Cisco documentation to [email protected].

You can submit comments by using the response card (if present) behind the front cover of your

document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you can perform these tasks:

• Report security vulnerabilities in Cisco products.

• Obtain assistance with security incidents that involve Cisco products.

• Register to receive security information from Cisco.

A current list of security advisories and notices for Cisco products is available at this URL:

http://www.cisco.com/go/psirt

If you prefer to see advisories and notices as they are updated in real time, you can access a Product

Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Obtaining Technical Assistance

Reporting Security Problems in Cisco Products

Cisco is committed to deliveringsecure products. We test our products internally before we release them,

and we strive to correct all vulnerabilities quickly. If you think that you might have identified a

vulnerability in a Cisco product, contact PSIRT:

• Emergencies—[email protected]

An emergency is either a condition in which a system is under active attack or a condition for which

a severe and urgent security vulnerability should be reported. All other conditions are considered

nonemergencies.

• Nonemergencies—[email protected]

In an emergency, you can also reach PSIRT by telephone:

• 1 877 228-7302

• 1 408 525-6532

Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product to encrypt any sensitive

information that you send to Cisco. PSIRT can work from encrypted information that is compatible with

PGP versions 2.x through 8.x.

Never use a revoked or an expired encryption key. The correct public key to use in your correspondence

with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page

at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

The link on this page has the current PGP key ID in use.

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco

Technical Support & Documentation website on Cisco.com features extensive online support resources.

In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC)

engineers provide telephone support. If you do not have a valid Cisco service contract, contact your

reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online documents and tools for

troubleshooting and resolving technical issues with Cisco products and technologies. The website is

available 24 hours a day, at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user

ID and password. If you have a valid service contract but do not have a user ID or password, you can

http://tools.cisco.com/RPF/register/register.do

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Obtaining Technical Assistance

Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting

a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &

Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose

Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco

Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by

product ID or model name; by tree view; or for certain products, by copying and pasting show command

output. Search results show an illustration of your product with the serial number label location

highlighted. Locate the serial number label on your product and record the information before placing a

service call.

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3

and S4 service requests are those in which your network is minimally impaired or for which you require

product information.) After you describe your situation, the TAC Service Request Tool provides

recommended solutions. If your issue is not resolved using the recommended resources, your service

request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone.

(S1 or S2 service requests are those in which your production network is down or severely degraded.)

Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business

operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553-2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity

definitions.

Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You

and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your

business operation are negatively affected by inadequate performance of Cisco products. You and Cisco

will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of your network is impaired, but most business operations

remain functional. You and Cisco will commit resources during normal business hours to restore service

to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or

configuration. There is little or no effect on your business operations.

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online

and printed sources.

• Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo

merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

• Cisco Press publishes a wide range of general networking, training and certification titles. Both new

and experienced users will benefit from these publications. For current Cisco Press titles and other

information, go to Cisco Press at this URL:

http://www.ciscopress.com

• Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and

networking investments. Each quarter, Packet delivers coverage of the latest industry trends,

technology breakthroughs, and Cisco products and solutions, as well as network deployment and

troubleshooting tips, configuration examples, customer case studies, certification and training

information, and links to scores of in-depth online resources. You can access Packet magazine at

this URL:

http://www.cisco.com/packet

• iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies

learn how they can use technology to increase revenue, streamline their business, and expand

services. The publication identifies the challenges facing these companies and the technologies to

help solve them, using real-world case studies and business strategies to help readers make sound

technology investment decisions. You can access iQ Magazine at this URL:

http://www.cisco.com/go/iqmagazine

or view the digital edition at this URL:

http://ciscoiq.texterity.com/ciscoiq/sample/

• Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering

professionals involved in designing, developing, and operating public and private internets and

intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Obtaining Additional Publications and Information

• Networking products offered by Cisco Systems, as well as customer support services, can be

obtained at this URL:

http://www.cisco.com/en/US/products/index.html

• Networking Professionals Connection is an interactive website for networking professionals to

share questions, suggestions, and information about networking products and technologies with

Cisco experts and other networking professionals. Join a discussion at this URL:

http://www.cisco.com/discuss/networking

• World-class networking training is available from Cisco. You can view current offerings at

this URL:

http://www.cisco.com/en/US/learning/index.html

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

78-6507-06

Obtaining Additional Publications and Information

This document is to be used in conjunction with the Catalyst 6500 Series Software Configuration Guide and the Catalyst 6500 Series Command Reference publications.

CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and

iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified

Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Empowering the Internet Generation,

Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ

Net Readiness Scorecard, LightStream, Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing,

ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StrataView Plus, TeleRouter, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered

trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0502R)