Litter-Robot Litter-Robot LR3-8010-0g Litter Robot Open Air User guide

Brand
Litter-Robot
Model
Litter-Robot LR3-8010-0g Litter Robot Open Air
Type
User guide
Never push the Lier-Robot against
a wall or into a corner (must not be
touching any walls).
Cats must weigh at least 2.5kg to
safely use the Lier-Robot
in Automatic Mode.
Quick
sta
guide.
For a complete guided online
experience and tips on acclimating your
cat, please visit catevolution.com.au
Robot ready for use
Robot cycling
Sleep mode enabled, within
specied sleep time
Waste drawer full
Cat sensor fault
Cat detected and wait time
countdown initiated
Solid Blue
Flashing Yellow
Solid Yellow
Solid Blue & Yellow
Flashing Blue
Flashing Red
Solid Red
What’s in the Box
(3) Waste drawer linersCarbon lter
What do the
lights mean?
Accessories
(optional – sold separately or in bundle)
LR3-8010-0g
Need help? Visit catevolution.com.au
AC/DC power supply
Check for excess weight (such
as too much waste or lier) and
press Reset
Check for excess lier
or check bonnet
No action required or press
Reset to cancel timing
Cycle interrupted or
bonnet removed
lier-robot.com/geingstaed
Press and release the Empty buon to sta an empty cycle (empties all
lier into the waste drawer).
If already cycling, press Empty to pause; press again to cancel a cycle.
Press and hold, while at the home position, to enter wait time
seing mode.
Press and release the Reset buon to reset the cat sensor. (Do this
aer emptying the waste drawer, adding lier, etc.)
If already cycling, press Reset to pause; press again to cancel a cycle.
Press and hold, while at the home position, to enter control
panel lockout.
Press and release the Power buon to turn the robot ON or OFF.
The robot will begin a clean cycle when power is turned on.
Press and hold, while at the home position, to enter night light
seing mode.
Press and release the Cycle buon to sta a clean cycle.
If already cycling, press Cycle to pause; press again to resume a cycle.
Press and hold, while at the home position, to enter sleep mode.
Power
Empty
Cycle
Reset
LR3-8010-0g
Lier-Robot Connect units only – look for
the WiFi symbol on the control panel.
Download the Whisker app and follow the
onboarding instructions.
Ensure proper placement
Power on
Add lier
Download the app
1
3
2
4
If possible, place the Lier-Robot in the same location as the
old lier box (at least during transition).
Make sure the unit is indoors on a rm, level suace and in a
cool, dry location.
Place lier mats or rugs in front of the unit.
Inse the small plug
end of the power cord
into the socket on the
back of the base.
The Lier-Robot will now peorm an initial clean cycle. Need help? Visit catevolution.com.au
Use clumping lier or lier beads and crystals that are small
enough to pass through the screen.
Add lier until it meets the raised ll line when spread flat
(8-10 lbs or 4kg). Be careful not to oveill.
Lier Fill Line
Plug the AC/DC
adapter into a wall
outlet.
Press the Power
buon on the
control panel.
Control
panel
icons
  • Page 1 1
  • Page 2 2

Litter-Robot Litter-Robot LR3-8010-0g Litter Robot Open Air User guide

Brand
Litter-Robot
Model
Litter-Robot LR3-8010-0g Litter Robot Open Air
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents