Worx WX744 User manual

Type
User manual

Worx WX744 is a versatile tool suitable for wire joining and wood burning. It features precise temperature control, allowing you to adjust the temperature from 200 to 480°C in 10°C increments. The device is easy to operate, with a user-friendly interface and an LED display for temperature monitoring. The WX744 also comes with a comfort sleeve for enhanced grip and a trestle stand for safe storage when not in use. Safety features include auto sleep after 5 minutes of inactivity and auto power-off after 10 minutes to prevent overheating.

Worx WX744 is a versatile tool suitable for wire joining and wood burning. It features precise temperature control, allowing you to adjust the temperature from 200 to 480°C in 10°C increments. The device is easy to operate, with a user-friendly interface and an LED display for temperature monitoring. The WX744 also comes with a comfort sleeve for enhanced grip and a trestle stand for safe storage when not in use. Safety features include auto sleep after 5 minutes of inactivity and auto power-off after 10 minutes to prevent overheating.

SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS
WX744 WX744.X
2
EN
PRODUCT SAFETY
GENERAL SAFETY WARNINGS
WARNING: Read all safety warnings and
instructions.
Failure to follow all instructions
listed below may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge if they have been
given supervision or instruction concerning use
of the appliance in a safe way and understand the
hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall
not be made by children without supervision.
WARNING: For the purposes of recharging the
battery, only use the detachable supply unit
provided with this appliance.
ADDITIONAL SAFETY RULES FOR CRAFTER
WARNING: This tool must be placed on its stand
when not in use.
A fire may result if the appliance is not used with
3
EN
care, therefore
– be careful when using the appliance in places
where there are combustible materials;
– do not apply to the same place for a long time;
– do not use in presence of an explosive
atmosphere;
– be aware that heat may be conducted to
combustible materials that are out of sight;
– place the appliance on its stand after use and
allow it to cool down before storage;
– do not leave the appliance unattended when it is
switched on.
SAFETY WARNINGS FOR BATTERY PACK
a)Do not dismantle, open or shred cells or
battery pack.
b)Do not short-circuit a battery pack. Do
not store battery packs haphazardly in
a box or drawer where they may short-
circuit each other or be short-circuited
by conductive materials.
When battery
pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may
4
EN
cause burns or a fire.
c)Do not expose battery pack to heat or
fire. Avoid storage in direct sunlight.
d)Do not subject battery pack to
mechanical shock.
e)In the event of battery leaking, do not
allow the liquid to come into contact
with the skin or eyes. If contact has
been made, wash the affected area
with copious amounts of water and
seek medical advice.
f) Seek medical advice immediately
if a cell or battery pack has been
swallowed.
g)Keep battery pack clean and dry.
h)Wipe the battery pack terminals with a
clean dry cloth if they become dirty.
i) Battery pack needs to be charged
before use. Always refer to this
instruction and use the correct
charging procedure.
j) Do not maintain battery pack on charge
when not in use.
k)After extended periods of storage,
it may be necessary to charge and
discharge the battery pack several
times to obtain maximum performance.
5
EN
l) Battery pack gives its best
performance when it is operated at
normal room temperature (20°C ± 5°C).
m)When disposing of battery packs,
keep battery packs of different
electrochemical systems separate
from each other.
n)Recharge only with the charger
specified by Worx. Do not use any
charger other than that specifically
provided for use with the equipment.
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
o)Do not use any battery pack which
is not designed for use with the
equipment.
p)Keep battery pack out of the reach of
children.
q)Retain the original product literature
for future reference.
r) Remove the battery from the
equipment when not in use.
s)Dispose of properly.
t) Do not mix cells of different
manufacture, capacity, size or type
within a device.
6
EN
u)Do not remove battery pack from its
original packaging until required for
use.
v)Observe the plus (+) and minus (–)
marks on the battery and ensure
correct use.
SYMBOLS
Read operators manual
Warning
Wear eye protection
Wear protective gloves
Do not burn
Batteries may enter water cycle if disposed improperly, which can be
hazardous for ecosystem. Do not dispose of waste batteries as unsorted
municipal waste.
Li-I on
Li-Ion battery. This product has been marked with a symbol relating
to ‘separate collection’ for all battery packs and battery pack. It will
then be recycled or dismantled in order to reduce the impact on the
environment. Battery packs can be hazardous for the environment and
for human health since they contain hazardous substances.
Waste electrical products must not be disposed of with household
waste. Please recycle where facilities exist. Check with your local
authorities or retailer for recycling advice.
5
1234
6
8
EN
COMPONENT LIST
1. POWER BUTTON
2. “” BUTTON
3. LCD DISPLAY
4. “” BUTTON
5. CRAFTER TIP
6. COMFORT SLEEVE OPTIONAL
Not all the accessories illustrated or described are included in standard
delivery.
TECHNICAL DATA
Type WX744 WX744.X (744 - designation of machinery, representative of
crafter)
WX744 WX744.X *
Rated voltage 20 V Max. **
Power input 45 W
Max temperature 200 °C-480 °C
Battery type Lithium battery
Machine weight (bare tool) 54 g
* X=1-999, A-Z, M1-M9 there are only used for different customers, there are no safe
relevant changes between these models.
** Voltage measured without workload. Initial battery voltage reaches maximum of 20
volts. Nominal voltage is 18 volts.
Category Model Capacity
20V Hub/HubX
WA7160 Input: 20 V 10 A Max.
Output: 20 V 10 A Max.
WA7161 Input: 20 V 10 A Max.
Output 1: 20 V 10 A Max.
Output 2: 5 V 2 A (USB port)
We recommend that you purchase your accessories from the same store that sold you
the tool. Refer to the accessory packaging for further details. Store personnel can assist
you and offer advice.
MakerX series tools and 20V Hub/HubX are specially designed to work together, so do
not attempt to use any other devices.
1
2
1
2
A1 A2
A3 B
C D
E1 E2
1
2
1
2
A1 A2
A3 B
C D
E1 E2
11
EN
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction book carefully.
ASSEMBLY
1. Assemble the crafter tips as shown in Fig. A1-A3.
2. Connect the crafter and the hub. (See Fig. B)
WARNING: Before operation, make sure the speed control button on the
hub is at the“Min“ position. (See Fig. C)
OPERATION
1. Confirm the speed control button is set to “Min. Grasp the tool by the grip.Press
on/off switch on the hub. Then press and hold the power button on the crafter to start
working. (See Fig. D)
NOTE: The speed is fixed, and can not be adjusted by the speed control button on the
hub.
During operation, the crafter will enter into auto sleep with no movement for
approximately 5 minutes or more. The temperature will drop to 200 °C and the crafter
automatically turns off 10 minutes later. It will display “OFF.
WARNING: During initial use, the crafter may generate a light smoke
due to elements heating, which is normal.
While the crafter is heating, DO NOT touch the metallic parts near the tip
and DO NOT remove or replace the tip.
Never operate the crafter while people, especially young children are nearby.
Be careful. The crafter remains hot after the work is concluded.
2. Press the on/off switch on the hub to turn off after use.
NOTE: Use the trestle to place the crafter when not in use.
3. Adjust temperature as needed.
Press on/off switch on the hub. Use “+” or”-” button to adjust temperature (the
temperature will increase / decrease by 10 °C each time the “+” or “-” button is
pressed).
NOTE: The temperature cannot be adjusted during the heating or cooling process.
4. Switch °F and °C as needed. (See Fig. E1, E2)
Press on/off switch on the hub. With the crafter turned off, press both “+” and ”-”
button and “UNI” will be shown on the LCD display. Then press both “+” and ”-” button
to switch the temperature mode. After selection, wait for 3 seconds and then it will
display “OFF”.
5. Your Wood & Metal Crafter comes with an optional silicon Comfort Sleeve. To
12
EN
enhance the grip, simply slide the sleeve over the nose of the tool.
MAINTENANCE
Remove the battery before carrying out any adjustment, servicing or mainte-
nance.
There are no user serviceable parts in your power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power
tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through the ventilation slots. This is normal
and will not damage your power tool. Store the accessories in a dry place.
ENVIRONMENTAL PROTECTION
Waste electrical products must not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authorities or
retailer for recycling advice.
13
EN
DECLARATION OF CONFORMITY
We,
Positec Germany GmbH
Grüner Weg 10, 50825 Cologne, Germany
On behalf of Positec declare that the product
Description
Wood & Metal Crafter
Type
WX744 WX744.X (744 - designation of machinery, representative of crafter)
Function
Wire joining, wood burning
Complies with the following Directives:
2014/30/EU,
2011/65/EU & (EU)2015/863
Standards conform to
EN 60335-1,
EN 60335-2-45,
EN 62233,
EN 55014-1,
EN 55014-2
2020/11/24
Allen Ding
Deputy Chief Engineer,Testing & Certification
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China
14
EN
DECLARATION OF CONFORMITY
We,
Positec Power Tools (Europe) Ltd,
PO Box 6242, Newbury, RG14 9LT, UK
On behalf of Positec declare that the product
Description
Wood & Metal Crafter
Type
WX744 WX744.X (744 - designation of machinery, representative of crafter)
Function
Wire joining, wood burning
Complies with the following Directives:
Electromagnetic Compatibility Regulations 2016
The Restriction of the Use of Certain Hazardous Substances in Electrical and
Electronic Equipment Regulations
Standards conform to
BS EN 60335-1,
BS EN 60335-2-45,
BS EN 62233,
BS EN 55014-1,
BS EN 55014-2
2020/11/24
Allen Ding
Deputy Chief Engineer,Testing & Certification
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China
Copyright © 2020, Positec. All Rights Reserved.
AR01539500
www.worx.com
After-sales Service and Application
At www.worx.com you can order spare parts or arrange the
collection of a product in need of servicing or repair.
Tel. Service: 0345 202 9679
E-Mail: customerservices@worxtools.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Worx WX744 User manual

Type
User manual

Worx WX744 is a versatile tool suitable for wire joining and wood burning. It features precise temperature control, allowing you to adjust the temperature from 200 to 480°C in 10°C increments. The device is easy to operate, with a user-friendly interface and an LED display for temperature monitoring. The WX744 also comes with a comfort sleeve for enhanced grip and a trestle stand for safe storage when not in use. Safety features include auto sleep after 5 minutes of inactivity and auto power-off after 10 minutes to prevent overheating.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI