Gigabyte MC13-LE0 User manual

MC13-LE0

MC13-LE1

AMD Ryzen™ 7000 Server Board

User Manual

Rev. 1.0

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specifications and features in this manual may be made by GIGABYTE

without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classications

In order to assist in the use of this product, GIGABYTE provides the following types of documentation:

 UserManual:detailedinformation&stepsabouttheinstallation,congurationandusethis

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

  softwarecomponent(e.g.BMCrmware,rail-kit)compatiblewiththisproduct.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents

For More Information

Forrelatedproductspecications,thelatestrmwareandsoftware,andotherinformation,pleasevisit

our website at: http://www.gigabyte.com.

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our

reseller portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

http://esupport.gigabyte.com/ to create a new support ticket.

For any general sales or marketing enquires, you may message GIGABYTE server directly by

email: server[email protected].

- 3 -

Table of Contents

MC13-LE0/MC13-LE1 Motherboard Layout ....................................................................5

Block Diagram .................................................................................................................7

Chapter 1 Hardware Installation .....................................................................................8

1-1 Installation Precautions .................................................................................... 8

1-2 ProductSpecications ...................................................................................... 9

1-3 Installing and Removing the CPU .................................................................. 12

1-4 Installing and Removing Memory ................................................................... 13

1-4-1 2-ChannelMemoryConguration ..........................................................................13

1-4-2 Installing and Removing a Memory Module ..........................................................14

1-5 Installing the M.2 SSD Module ....................................................................... 15

1-6 Back Panel Connectors .................................................................................. 16

1-7 Internal Connectors ........................................................................................ 18

1-8 Jumper Settings ............................................................................................. 26

Chapter 2 BIOS Setup ..................................................................................................27

2-1 The Main Menu .............................................................................................. 29

2-2 Advanced Menu ............................................................................................. 31

2-2-1 Trusted Computing .................................................................................................33

2-2-2 AMDfTPMConguration ........................................................................................35

2-2-3 AST2600SuperIOConguration ...........................................................................36

2-2-4 S5 RTC Wake Settings ...........................................................................................38

2-2-5 Serial Port Console Redirection .............................................................................39

2-2-6 CPUConguration ..................................................................................................43

2-2-7 PCI Subsystem Settings .........................................................................................44

2-2-8 USBConguration ..................................................................................................46

2-2-9 NetworkStackConguration ..................................................................................48

2-2-10 CSMConguration .................................................................................................49

2-2-11 PostReportConguration ......................................................................................50

2-2-12 NVMeConguration ...............................................................................................51

2-2-13 SATAConguration.................................................................................................52

2-2-14 ChipsetConguration .............................................................................................53

2-2-15 RAMDiskConguration .........................................................................................54

2-2-16 TlsAuthConguration ............................................................................................55

2-2-17 iSCSIConguration ................................................................................................56

2-2-18 Intel(R) I210 Gigabit Network Connection ..............................................................57

2-2-19 Intel(R) X710 Ethernet Network Connection ..........................................................59

2-2-20 VLANConguration ................................................................................................61

- 4 -

2-2-21 MACIPv4NetworkConguration ...........................................................................62

2-2-22 MACIPv6NetworkConguration ...........................................................................63

2-2-23 Driver Health ...........................................................................................................64

2-3 Chipset Setup Menu ....................................................................................... 65

2-3-1 North Bridge ...........................................................................................................66

2-4 Server Management Menu ............................................................................. 67

2-4-1 System Event Log ..................................................................................................69

2-4-2 View FRU Information ............................................................................................70

2-4-3 Bmc self test log .....................................................................................................71

2-4-4 BMCVLANConguration .......................................................................................72

2-4-5 BMCNetworkConguration ...................................................................................73

2-4-6 BMC User Settings .................................................................................................74

2-4-7 IPv6BMCNetworkConguration ...........................................................................75

2-5 Security Menu ................................................................................................ 76

2-5-1 Secure Boot ...........................................................................................................77

2-6 Boot Menu ...................................................................................................... 79

2-7 Save & Exit Menu ........................................................................................... 80

2-8 BIOS Recovery .............................................................................................. 82

2-9 BIOS POST Beep code (AMI standard) ......................................................... 83

2-9-1 PEI Beep Codes .....................................................................................................83

2-9-2 DXE Beep Codes ...................................................................................................83

- 5 -

MC13-LE0/MC13-LE1 Motherboard Layout

21

CPU

DIMM_P0_A0

DIMM_P0_B1

DIMM_P0_B0

DIMM_P0_A1

2 43

7

8

9

1216 13

17

18

20 19 14

15

21

22

23

24

26

25

27

28

29

30

31

65

10

11

1

- 6 -

Item Code Description

1 CN_NCSI NCSI Connector

2 SW_ID ID Button with LED

3 LAN1_2 1GbE LAN Port #1/#2 (MC13-LE0 Supported)

4 USB3_MLAN Server Management LAN Port (Top)/ USB 3.2 Gen1 Ports (Bottom)

5 LAN1 10GbE LAN Port #1 (MC13-LE1 Supported)

6 LAN2 10GbE LAN Port #2 (MC13-LE1 Supported)

7 COM_VGA Serial Port (Top)/ VGA Port (Bottom)

8 P12V_AUX 2x4 Pin 12V Power Connector

9 PMBUS PMBus Connector

10 CPU0_FAN CPU0 Fan Connector

11 ATX 2x12 Pin Main Power Connector

12 SYS_FAN5 System Fan Connector #5

13 SYS_FAN4 System Fan Connector #4

14 SYS_FAN3 System Fan Connector #3

15 SYS_FAN1 System Fan Connector #1

16 SYS_FAN2 System Fan Connector #2

17 SPI_TPM TPM Connector

18 SATA_0_1 SATAIII 6Gb/s Connector #0/#1

19 SATA_2_3 SATAIII 6Gb/s Connector #2/#3

20 USB_A USB 2.0 Type-A Connector

21 F_USB3 Front Panel USB 3.2 Gen1 Connector

22 FP_1 Front Panel Header

23 F_USB2 Front Panel USB 2.0 Header

24 IPMB IPMB Connector

25 M2_0 M.2 Slot (PCIe Gen5 x4, Supports NGFF-2280)

26 BP_1 HDD Backplane Board Connector

27 PCIE_1 PCIe x4 Slot (Gen4 x4)

28 LED_BMC BMC Firmware Readiness LED

29 PCIE_3 PCIe x16 Slot (Gen5 x16)

30 CASE_OPEN Case Open Intrusion Alert Header

31 BAT Battery Socket

- 7 -

Block Diagram

- 8 -

Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can

become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read

the user's manual and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

• To avoid any potential short circuit of the DIMM slots, please remove any stand-offs from the

chassis that will be located underneath the DIMM slots, before installing the motherboard

into the chassis.

• WheninstallingwatercoolingkitforCPUorGPU,pleasekeepproperairowandventilate

the motherboard to prevent heat accumulation.

Chapter 1 Hardware Installation

- 9 -

Hardware Installation

1-2 Product Specications

Socket

Security

Security Server Operating Properties

Power Supply

Form Factor microATX

244W x 244D (mm)

Socket

Security

Security Server Operating Properties

Power Supply

CPU AMD Ryzen™ 7000 Series Processors

Note:

- Recommend to install 170 watts CPU with water cooling kit.

-WheninstallingwatercoolingkitforCPUorGPU,pleasekeepproperairowand

ventilate the motherboard to prevent heat accumulation.

Socket

Security

Security Server Operating Properties

Power Supply

Socket AM5

Socket

Security

Security Server Operating Properties

Power Supply

Chipset AMD B650E

Socket

Security

Security Server Operating Properties

Power Supply

Memory 4 x DDR5 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity)

of system memory

Dual channel memory architecture

Supported ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules*

Supported non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules

Memory speed: up to 5200MHz for 1DPC ; up to 3600MHz for 2DPC

Socket

Security

Security Server Operating Properties

Power Supply

LAN MC13-LE0:

2 x 1GbE LAN ports ( Intel® I210-AT)

1 x 10/100/1000 management LAN

MC13-LE1:

2 x 10 GbE LAN ports ( Intel® X710)

1 x 10/100/1000 management LAN

Socket

Security

Security Server Operating Properties

Power Supply

Onboard

Graphics

Integrated in Aspeed® AST2600

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp

Socket

Security

Security Server Operating Properties

Power Supply

Storage Interface 4 x SATA 6Gb/s ports

Socket

Security

Security Server Operating Properties

Power Supply

RAID RAID 0/1/10

Socket

Security

Security Server Operating Properties

Power Supply

Expansion Slots Slot_3 (PCIEX16): 1 x PCIe x16 (Gen5 x16 bus) slot from CPU

Slot_1 (PCIEX4): 1 x PCIe x4 (Gen4 x4 bus) slot from chipset

1 x M.2 slot:

- M-key

- PCIe Gen5 x4

- Supports NGFF-2242/2280

NOTE:

We reserve the right to make any changes to the product specications and product-related

information without prior notice.

- 10 -

Hardware Installation

Socket

Security

Security Server Operating Properties

Power Supply

Internal I/O

Connectors

1 x 24-pin ATX main power connector

1 x 8-pin ATX 12V power connector

4 x SATA ports

1 x M.2 slot

1 x HDD back plane board header

1 x CPU fan header

5 x System fan headers

1 x USB 3.2 Gen1 header with 2-ports

1 x USB 2.0 type-A connector

1 x USB 2.0 header with 2-ports

1 x TPM header

1 x Front panel header

1 x IPMB connector

1 x PMBUS connector

1xClearCMOSjumpe

Socket

Security

Security Server Operating Properties

Power Supply

Rear I/O

Connectors

2 x USB 3.2 Gen1 type A

1 x VGA

1 x COM

2 x 1GbE RJ45 LAN

1 x MLAN

1 x ID button with LED

Socket

Security

Security Server Operating Properties

Power Supply

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

Socket

Security

Security Server Operating Properties

Power Supply

- 11 -

Hardware Installation

Socket

Security

Security Server Operating Properties

Power Supply

Board

Management

Aspeed® AST2600 Management Controller

GIGABYTE Management Console (AMI MegaRAC SP-X) Web Interface

Dashboard

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

FanProle

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup&RestoreConguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

Socket

Security

Security Server Operating Properties

Power Supply

Operating

Properties Operating temperature: 10°C to 35°C

Operating humidity: 8-80% (non-condensing)

Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

- 12 -

Hardware Installation

1-3 Installing and Removing the CPU

Read the following guidelines before you begin to install the CPU:

• Make sure that the motherboard supports the CPU.

• Always turn off the computer and unplug the power cord from the power outlet before installing

the CPU to prevent hardware damage.

• Unplug all cables from the power outlets.

• Disconnect all telecommunication cables from their ports.

• Placethesystemunitonaatandstablesurface.

• Open the system according to the instructions.

WARNING!

Failure to properly turn off the server before you start installing components may cause serious

damage. Do not attempt the procedures described in the following sections unless you are a

qualiedservicetechnician.

Follow these instructions to Install the CPU:

1. Gently press the CPU socket lever handle down and away from the socket. Lift up the CPU socket

locking lever and then open the CPU cover.

2. Align the CPU pin one (triangle marking) with the pin one corner of the CPU socket. Install the CPU

onto the socket.

3. Ensure the CPU is positioned into its socket and then close the CPU cover. Secure the CPU socket lever

under its retention tab. The plastic protective cover will pop off by itself and can be removed.

Note: Always replace the plastic protective cover when the CPU is not installed to protect the CPU

socket.

1

2

3

Pin One

2

3

1

2

3

- 13 -

Hardware Installation

1-4 Installing and Removing Memory

Read the following guidelines before you begin to install the memory:

• Make sure that the motherboard supports the memory. It is recommended to use memory of the

same capacity, brand, speed, and chips.

• Always turn off the computer and unplug the power cord from the power outlet before installing

the memory to prevent hardware damage.

• Memory modules have a foolproof design. A memory module can be installed in only one

direction. If you are unable to insert the memory, switch the direction.

1-4-1 2-Channel Memory Conguration

This motherboard provides 4 DDR5 memory sockets and supports 2-Channel Technology. After the memory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.

21

CPU

DIMM_P0_A0

DIMM_P0_B1

DIMM_P0_B0

DIMM_P0_A1

- 14 -

Hardware Installation

1-4-2 Installing and Removing a Memory Module

• Before installing a memory module, make sure to turn off the computer and unplug the power

cord from the power outlet to prevent damage to the memory module.

• To avoid any potential short circuit of the DIMM slots, please remove any stand-offs from the

chassis that will be located underneath the DIMM slots, before installing the motherboard into the

chassis.

• Be sure to install DDR5 DIMMs on this motherboard.

1

2

Follow these instructions to install a DIMM module:

1. Insert the DIMM memory module vertically into the DIMM slot and push it down.

2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.

3. Reverse the installation steps when you want to remove the DIMM module.

Memory Type DDR5

Voltage (V) 5V

Connector UDIMM ECC/Non-ECC

Speed (MT/s) 5200 3600

Channels 1,2

DIMM Per Channel 1,2

DIMM Capacity (GB) 2,4,8,16,32

Note:

• When only one DIMM is used, it must be populated in memory slot A1.

- 15 -

Hardware Installation

1-5 Installing the M.2 SSD Module

Follow the steps below to install a M.2 SSD module on your motherboard.

Step1. Insert the M.2 SSD module into the slot.

Step2. Secure it with the screw, tightening as necessary to fasten the M.2 SSD module in place.

1

2

- 16 -

Hardware Installation

1

2

3

4

5

7

6

1-6 Back Panel Connectors

uSerial Port

Connects to serial-based mouse or data processing devices.

vVGA Port

Connects to a monitor device.

wServer Management LAN Port

The LAN port provides Internet connection with data transfer speeds of 10/100/1000Mbps. This port is

the dedicated LAN port for Server Management.

xUSB 3.2 Gen1 Ports

TheUSBportsupportstheUSB3.2Gen1specication.UsethisportforUSBdevicessuchasaUSB

keyboard/mouse,USBprinter,USBashdriveetc.

y1GbE LAN Port #2

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. See the section

below for a description of the states of the LAN port LEDs.

z1GbE LAN Port #1

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. See the section

below for a description of the states of the LAN port LEDs.

{ID button with LED

Whenthesystemidenticationisactive,theIDLEDonthefront/backpanelglowsblue.

MC13-LE0

1

2

3

5

67

4

MC13-LE1

uSerial Port

Connects to serial-based mouse or data processing devices.

vVGA Port

Connects to a monitor device.

- 17 -

Hardware Installation

• Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

• When removing the cable, pull it straight out from the connector. Do not rock it side to side to

prevent an electrical short inside the cable connector.

LAN and ID Button LEDs

Link/Activity LED

Speed LED

LAN Port

ID button/LED:

10/100/1000 LAN LED:

State Description

Yellow On 1Gbps data rate

Green On 100Mbps data rate

Off 10Mbps data rate

State Description

Blue On Systemidenticationisactive

Off Systemidenticationisdisabled

w10GbE LAN Port #2

The Gigabit Ethernet LAN port provides Internet connection at up to 10 Gbps data rate. See the section

below for a description of the states of the LAN port LEDs.

x10GbE LAN Port #1

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. See the section

below for a description of the states of the LAN port LEDs.

yServer Management LAN Port

The LAN port provides Internet connection with data transfer speeds of 10/100/1000Mbps. This port is

the dedicated LAN port for Server Management.

zUSB 3.2 Gen1 Ports

TheUSBportsupportstheUSB3.2Gen1specication.UsethisportforUSBdevicessuchasaUSB

keyboard/mouse,USBprinter,USBashdriveetc.

{ID button with LED

Whenthesystemidenticationisactive,theIDLEDonthefront/backpanelglowsblue.

10GbE LAN LED:

State Description

Yellow On 5Gbps, 2.5Gbps, 1Gps data rate

Green On 10Gbps data rate

Off 100Mbps data rate

- 18 -

Hardware Installation

1-7 Internal Connectors

Read the following guidelines before connecting external devices:

• First make sure your devices are compliant with the connectors you wish to connect.

• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

• After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) ATX 11) BP_1

2) P12V_AUX 12) SPI_TPM

3) SATA_0/1/2/3 13) IPMB

4) CPU0_FAN 14) CN_NCSI

5) SYS_FAN3/4/5 15) LED_BMC

6) SYS_FAN1/2 16) BAT

7) PMBUS 17) CASE_OPEN

8) F_USB3

9) F_USB2

10) FP_1

21

CPU

DIMM_P0_A0

DIMM_P0_B1

DIMM_P0_B0

DIMM_P0_A1

12

13

5

10

11

1

2

4

16

63

7

8

9

14

15

17

- 19 -

Hardware Installation

21

1/2) ATX/P12V_AUX (2x12 Main Power Connector and 2x4 12V Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturnedoff

and all devices are properly installed. The power connector possesses a foolproof design. Connect the power

supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies

power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

power consumption be used (500W or greater). If a power supply is used that does not provide the

required power, the result can lead to an unstable or unbootable system.

ATX

ATX_12V

8

5

4

1

PinNo. Denition

1 GND

2 GND

3 GND

4 GND

5 +12V

6 +12V

7 +12V

8 +12V

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3 GND 15 GND

4 +5V 16 PS_ON

5 GND 17 GND

6 +5V 18 GND

7 GND 19 GND

8 Power Good 20 -5V

9 5VSB 21 +5V

10 +12V 22 +5V

11 +12V 23 +5V

12 3.3V 24 GND

113

1224

- 20 -

Hardware Installation

21

3) SATA_0_1/SATA_2_3 (SATA III 6Gb/s Connectors)

The SATA connectors conform to SATA III 6Gb/s standard and are compatible with SATA 3Gb/s standard.

Each SATA connector supports a single SATA device.

PinNo. Denition

1 GND

2 TXP

3 TXN

4 GND

5 RXN

6 RXP

7 GND

1

7

21

4/5/6) CPU0_FAN/SYS_FAN1/SYS_FAN2/SYS_FAN3/SYS_FAN4/SYS_FAN5 (Fan Headers)

Themotherboardhasone4-pinCPUfanheader(CPU_FAN),andve4-pin(SYS_FAN)systemfanheaders.

Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect

it in the correct orientation (the black connector wire is the ground wire). The motherboard supports CPU

fan speed control, which requires the use of a CPU fan with fan speed control design. For optimum heat

dissipation, it is recommended that a system fan be installed inside the chassis.

1

PinNo. Denition

1 GND

2 +12V

3 Sense

4 Speed Control

• Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

• Thesefanheadersarenotconfigurationjumperblocks.Donotplaceajumpercaponthe

headers.

Page is loading ...

Gigabyte MC13-LE0 User manual

This manual is also suitable for

Gigabyte MC13-LE0 User manual

Related papers

Other documents