Traxxas TRX-4M Defender Operating instructions

Type
Operating instructions

This manual is also suitable for

Traxxas TRX-4M Defender: Conquer any terrain with this capable and versatile RC crawler. Its waterproof electronics, innovative portal axles, and high-performance motor deliver unmatched off-road performance. Explore new adventures, scale rocky trails, and dominate challenging obstacles with ease. Get ready for endless hours of thrilling expeditions with the Traxxas TRX-4M Defender.

Traxxas TRX-4M Defender: Conquer any terrain with this capable and versatile RC crawler. Its waterproof electronics, innovative portal axles, and high-performance motor deliver unmatched off-road performance. Explore new adventures, scale rocky trails, and dominate challenging obstacles with ease. Get ready for endless hours of thrilling expeditions with the Traxxas TRX-4M Defender.

Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected] HKC23030-R01 Rev 230926
1/18 Utility Trailer LED Light Kit Installation Instructions
Covers Part #9790
1
2
If you have questions or need technical assistance, call Traxxas at
(1-888-872-9927) (U.S. residents only)
For previously
installed light
kits*
Plug the Y-harness into an open
ACC port on the electronic control
module (ECM). The LED lights will turn
on when the ECM is powered on by
plugging in the battery.
*If there are no open ACC ports on the
ECM due to previously installed light
kits, unplug one of the connectors from
the previously installed light kit, plug
that connector into the Y-harness, and
then plug the Y-harness into the ECM.
Remove the trailer hitch
from the rear bumper.
Retain and reuse the two
2.5x8mm button-head
cap screws.
Insert the black connector from the
included Y-harness into the wire
mount as shown.
Plug the power wiring
connector from the trailer
into the black connector
previously installed in the
wire mount.
Use the
2.5x8mm
button-
head cap
screws
from Step 3
to secure both the
wire mount and the
trailer hitch to the rear
bumper.
7
Kit contents:
Toolbox (with LED tail lights wiring
harnesses and housing assemblies)
3x6mm countersunk cap screws
(CCS) (2)
Rubber wire plugs (6)
Y-harness
Wire mount
Tools required:
2.0 mm hex wrench
A. Feed the left and right LED tail light housing assemblies from
the toolbox through the trailer frame.
B. Position the power wiring harness into the slot in the front of
the toolbox as shown.
C. Place the toolbox on the trailer frame and push down until it
snaps into place.
A. Route both LED taillight wiring harnesses through the channels in the
underside of the trailer frame (see Trailer Lights Wiring Diagram). Install
the housing assemblies onto the left and right tail light posts with the
included 3x6mm CCS (2).
B. Install the supplied rubber wire plugs (6) to secure the wiring harnesses
to the underside of the trailer (see Trailer Lights Wiring Diagram).
LED Tail Light
Housing Assemblies
LED Tail Light
Housing Assembly
LED Tail
Light Housing
Assembly
Power Wiring
Harness
A
A
A
A
BB
B
B
B
B
B
C
3x6mm
CCS
2.5x8mm
BCS
Power Wiring
Connector
Power Wiring
Connector
Trailer
Hitch
Trailer
Hitch
Y-harness
Wire Mount
Blue
Wire
Wire
Mount
Wire
Mount
Rubber
Wire Plug
Rubber
Wire Plug
Rubber
Wire Plug Rubber
Wire Plug Rubber
Wire Plug
Rubber
Wire Plug Rubber
Wire Plug
3x6mm
CCS
3Trailer Lights Wiring Diagram
4 5 6
NOTE ORIENTATION
5
3
  • Page 1 1

Traxxas TRX-4M Defender Operating instructions

Type
Operating instructions
This manual is also suitable for

Traxxas TRX-4M Defender: Conquer any terrain with this capable and versatile RC crawler. Its waterproof electronics, innovative portal axles, and high-performance motor deliver unmatched off-road performance. Explore new adventures, scale rocky trails, and dominate challenging obstacles with ease. Get ready for endless hours of thrilling expeditions with the Traxxas TRX-4M Defender.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI