101
INSTALLATION & MAINTENANCE MANUAL
VML1
230V
50Hz
IP
44
1
These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following product:
VML1
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this product should only be carried out by a qualified electrician or competent person
to the current Building and IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product is Class II double insulated
• This product is IP44 rated
• This product is non-dimmable
• Provide power to the point of installation. Suitable IP rated junction boxes should be used where
required
• Remove the base plate by removing the 3 Allen screws (see Fig 1)
• Mark the location of the fixing holes, and drill the holes ensuring not to infringe with any joists,
gas/water pipes or electrical cables
• Feed the cable via the grommet on base plate, and secure base plate to surface
• Connect Live (brown), Neutral (blue) to the 2-way terminal block (see Fig 2)
Fig 1
2
VML1
These instrucons should be read carefully and retained aer installaon by the end user for future reference and
maintenance.
These instrucons should be used to aid installaon of the following product:
VML1
SAFETY
• Installaon of this product should only be carried out by a qualified electrician or competent person to the
current Building and IEE Wiring Regulaons (BS7671)
• Please isolate mains prior to installaon/maintenance
• Check the total load on the circuit (including when this luminaire is fied) does not exceed the rang of the
circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protecon) rang of this luminaire when deciding the locaon for installaon
• This product is Class II double insulated
• This product is IP44 rated
• This product is non-dimmable
INSTALLATION
Provide power to the point of installaon. Suitable IP rated juncon boxes should be used where required
Remove the base plate by removing the 3 Allen screws (see Fig 1)
Fig 1
Mark the locaon of the fixing holes, and drill the holes ensuring not to infringe with any joists, gas/water pipes
or electrical cables
Feed the cable via the grommet on base plate, and secure base plate to surface
Connect Live (brown), Neutral (blue) to the 2-way terminal block (see Fig 2)
Remove Allen screws
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
Do not use any source of high pressure washers to maintain or clean this product.
The unit should be recycled in the correct manner when it reaches the end of its life. Check local
authorities for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may
damage the fitting.
This product has a warranty of 3 years from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring Regulations, improper use, or removal of
the batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
WARNING
GENERAL
WARRANTY
3
Fig 2
Secure fing to base plate and fasten the 3 Allen screws
Switch on power and test for correct operaon
WARNING
This product must be disconnected from the circuit if subjected to any high voltage or insulaon resistance tesng.
Irreparable damage will occur if this instrucon is not followed.
Do not use any source of high pressure washers to maintain or clean this product.
GENERAL
The unit should be recycled in the correct manner when it reaches the end of its life. Check local authories for where
facilies exist.
Clean with a so dry cloth only, do not use aggressive cleaning products or solvents which may damage the fing.
WARRANTY
This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the current
edion of the IEE Wiring Regulaons, improper use, or removal of the batch codes will invalidate the warranty. If this
product should fail within its warranty period it should be returned to the place of purchase for a free of charge
replacement. ML Accessories does not accept responsibility for any installaon costs associated with the replacement
product. Your statutory rights are not affected. ML Accessories reserve the right to alter product specificaon without prior
noce.
Live (brown)
Neutral (blue)
Fig 2
• Secure fitting to base plate and fasten the 3 Allen screws
• Switch on power and test for correct operation
ML Accessories Group Limited
LU5 5TA
www.mlaccessories.co.uk SBAPR17V1
4
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories TPB14EMLED User manual
-
Knightsbridge LANTSS/LANTBK E27 Wall Mounted Lantern Fitting IP23 Max 40W User manual
-
-
-
Knightsbridge LWS4W User manual
-
-
-
-
-
Other documents
-
Knightsbridge NH016W 1W LED Aluminum Square Recessed Wall Light User manual
-
-
-
-
Saxby Lighting 90981 User manual
-
IP44 DE 20226468 User manual
-
Saxby Lighting 13929 User manual
