Sharp VL-NZ100U User manual

Category
Camcorders
Type
User manual

This manual is also suitable for

LIQUID CRYSTAL DISPLAY CAMCORDER
OPERATION MANUAL
MODEL
VL-NZ100U
VL-NZ150U
Important
Model No.:
Serial No.:
Please read this operation manual
carefully before using the camcorder.
For assistance in reporting the theft or
loss of
this product, record on the line
below the
model number and serial number which
are located on the bottom of the unit.
Please retain this information.
• See page 79 for use of Demo mode.
Appendix
Preparation
Useful Features
Operation References
Basic Operations
Advanced Features
Digital Still Camera
Features
i
Thank you for purchasing this camcorder from SHARP.
The camcorder will enhance your home video enjoyment and allow you to capture those
special moments. Please read this operation manual to familiarize yourself with the
camcorder’s features, so that you will get the most out of it. The video techniques section will
help you fully enjoy the many features this camcorder offers, and expand your video world.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
PRODUCT DISPOSAL
This Product utilizes tin-lead solder, and a fluorescent lamp containing a small
amount of mercury. Disposal of these materials may be regulated due to environ-
mental considerations. For disposal or recycling information, please contact your
local authorities or the Electronics Industries Alliance: www.eiae.org.
CAUTION
(applies to the supplied AC adapter)
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO
WIDE SLOT, FULLY INSERT.
CAUTION
If the AC adapter is misplaced or
needs to be replaced, obtain the
same type of adapter from a SHARP
service center of your dealer.
BATTERY DISPOSAL
CONTAINS LITHIUM-ION RECHARGEABLE BATTERY. MUST BE RECYCLED OR
DISPOSED OF PROPERLY. CONTACT LOCAL AGENCIES FOR INFORMATION ON
RECYCLING AND DISPOSAL PLANS IN YOUR AREA.
This symbol warns the user of uninsulated voltage within the
unit that can cause dangerous electric shocks.
This symbol alerts the user that there are important operating
and maintenance instructions in the literature accompanying
this unit.
CAUTION:
TO REDUCE THE RISK OF ELEC-
TRIC SHOCK, DO NOT REMOVE
COVER. NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSON-
NEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Important Information for Consumers in the U.S.
ii
Trademarks
• Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
• DPOF is a trademark of CANON INC., Eastman Kodak Company, Fuji Photo Film Co., Ltd. and
Matsushita Electric Industrial Co., Ltd.
• All other brand or product names are registered trademarks or trademarks of their respective
holders.
WARNINGCFCC Regulations state that any unauthorized changes or modifica-
tions to this equipment not expressly approved by the manufacturer could void the
user’s authority to operate this equipment.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful in-
terference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
CReorient or relocate the receiving antenna.
CIncrease the separation between the equipment and receiver.
CConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
CConsult the dealer or an experienced radio/TV technician for help.
CAUTION ON LITHIUM BATTERY (MEMORY BACKUP BATTERY)
If a battery is reversed (positive end where the negative end belongs and vice
versa), it can overheat and rupture. This has happened when young children install
batteries backwards. Warn children
not
to take out batteries or install them.
Parents
should install the lithium battery in the camcorder.
COPYRIGHT WARNING: It is the intent of SHARP that this unit be used in full compliance with the
copyright laws of the United States and that prior permission be ob-
tained from copyright owners whenever necessary.
NOTE
The camcorder’s LCD panel is a very high technology product with more than 120,000 thin-film tran-
sistors*, giving you fine picture detail. Occasionally, a pixel may appear on the screen as a fixed point
of blue, green, red, or black. Please note that this does not affect your camcorder’s performance.
*Specifications are subject to change without notice.
DECLARATION OF CONFORMITY
Sharp Camcorder
This device complies with Part 15 of the FCC Rules. Operation is subject to the follow-
ing two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430
Phone: 1-800-BE-SHARP
iii
should never be blocked by placing the
product on a bed, sofa, rug, or other
similar surface. This product should not
be placed in
a built-in
installation
such as a
bookcase or
rack unless
proper ventilation is provided or the
manufacturer’s instructions have been
adhered to.
11. Power SourcesCThis product should
be operated only from the type of power
source indicated on the marking label. If
you are not sure of the type of power
supply to your home, consult your
product dealer or local power company.
For products intended to operate from
battery power, or other sources, refer to
the operating instructions.
12. Grounding or PolarizationCThis product
may be equipped with a polarized
alternating-current line plug (a plug
having one blade wider than the other).
This plug will fit into the power outlet
only one way. This is a safety feature. If
you are unable to insert the plug fully
into the outlet, try reversing the plug. If
the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose
of the polarized plug.
13. Power-Cord ProtectionCPower-supply
cords should be routed so that they are
not likely to be walked on or pinched by
items placed upon or against them,
paying particular attention to cords at
plugs, convenience receptacles, and
the point where they exit from the
product.
14. LightningCFor added protection for this
product during a lightning storm, or
when it is left unattended and unused
for long periods of time, unplug it from
the wall outlet and disconnect the
antenna or cable system. This will
prevent damage to the product due to
lightning and power-line surges.
1. Read InstructionsCAll the safety and
operating instructions should be read
before the product is operated.
2. Retain InstructionsCThe safety and
operating instructions should be
retained for future reference.
3. Heed WarningsCAll warnings on the
product and in the operating instruc-
tions should be adhered to.
4. Follow InstructionsCAll operating and
use instructions should be followed.
5. CleaningCUnplug this product from the
wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
6. AttachmentsCDo not use attachments
not recommended by the product
manufacturer as they may cause
hazards.
7. Water and MoistureCDo not use this
product near waterCfor example, near
a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near
a swimming pool; and the like.
8. AccessoriesCDo not place this product
on an unstable cart, stand, tripod,
bracket, or table. The product may fall,
causing serious injury to a child or
adult, and
serious damage
to the product.
Use only with a
cart, stand,
tripod, bracket,
or table recommended by the manu-
facturer, or sold with the product. Any
mounting of the product should follow
the manufacturer’s instructions, and
should use a mounting accessory
recommended by the manufacturer.
9. A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces
may cause the product
and cart combination to overturn.
10. VentilationCSlots and openings in the
cabinet are provided for ventilation and
to ensure reliable operation of the
product and to protect it from overheat-
ing, and these openings must not be
blocked or covered. The openings
IMPORTANT SAFEGUARDS
iv
15. Power LinesCAn outside antenna
system should not be located in the
vicinity of overhead power lines or other
electric light or power circuits, or where
it can fall into such power lines or
circuits. When installing an outside
antenna system, extreme care should
be taken to keep from touching such
power lines or circuits as contact with
them might be fatal.
16. OverloadingCDo not overload wall
outlets, extension cords, or integral
convenience receptacles as this can
result in a risk of fire or electric shock.
17. Object and Liquid EntryCNever push
objects of any kind into this product
through openings
as they may touch
dangerous
voltage points or
short-out parts
that could result in
a fire or electric shock. Never spill liquid
of any kind on the product.
18. ServicingCDo not attempt to service
this product yourself as opening or
removing covers may expose you to
dangerous voltage or other hazards.
Refer all servicing to qualified service
personnel.
19. Damage Requiring ServiceCUnplug
this product from the wall outlet and
refer servicing to qualified service
personnel under the following condi-
tions:
a. When the power-supply cord or plug
is damaged,
b. If liquid has been spilled, or objects
have fallen into the product,
c. If the product has been exposed to
rain or water,
d. If the product does not operate
normally by following the operating
instructions. Adjust only those
controls that are covered by the
operating instructions as an im-
proper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the product to
its normal operation,
e. If the product has been dropped or
damaged in any way, and
f. When the product exhibits a distinct
change in performanceCthis
indicates a need for service.
20. Replacement PartsCWhen replacement
parts are required, be sure the service
technician has used replacement parts
specified by the manufacturer or have
the same characteristics as the original
part. Unauthorized substitutions may
result in fire, electric shock, or other
hazards.
21. Safety CheckCUpon completion of any
service or repairs to this product, ask
the service technician to perform safety
checks to determine that the product is
in proper operating condition.
22. Wall or Ceiling MountingCThe product
should be mounted to a wall or ceiling
only as recommended by the manufac-
turer.
23. HeatCThe product should be situated
away from heat sources such as
radiators, heat registers, stoves, or
other products (including amplifiers)
that produce heat.
v
Quick Operation Guide
vi
Inserting a Cassette
1 Attach the power source to the
camcorder, then slide the cassette
compartment door release and open the
cassette compartment door.
• After confirmation sound, the cassette
holder extends and opens automatically.
2 Insert a commercially available cassette
fully with the window facing outwards,
and with the erasure protect tab facing
upwards.
3 Press the W mark gently until the
cassette holder clicks into place.
• After confirmation sound, the cassette
holder retracts automatically.
4 Wait for the cassette holder to fully
retract. Close the compartment door by
pressing the center until it clicks into
place.
vii
Quick Operation Guide
Easy Camera Recording
on Tape
1 Insert a cassette into the camcorder.
2 Set the Media Selection
switch to TAPE.
3 Hold down the Lock button and set the
Power switch to CAMERA.
• The picture from the lens now displays.
4 Press the REC START/STOP button to
begin recording.
To pause recording
Press the REC START/STOP button again.
AUTO
REC
Zooming
Push the Power Zoom control to T (1) (tele-
photo) or W (2) (wide angle) side.
Tape Playback
1 Set the Media Selection
switch to TAPE.
2 Hold down the Lock button
and set the Power switch to
VCR.
3 Press j (or k) on the Operation button
to rewind (or fast forward) the tape to the
desired point.
4 Press m to begin playback.
To stop playback
Press l.
Volume Control
Push the Volume control to the L or + side to
increase (1) or decrease (2) the volume.
Power switch
STILL button
REC START/STOP button
Power Zoom control/Volume control
Operation button
Media Selection switch
Power Zoom control
Volume control
Lock button
SET button
Lock button
viii
Card Recording
1 Insert a card into the camcorder.
2 Set the Media Selection
switch to CARD.
3 Hold down the Lock button and set the
Power switch to CAMERA.
• The picture from the lens now displays.
4 Adjust the Power Zoom control to frame
the subject as you desire.
5 Press the STILL button half-way down to
focus on the subject.
• The camcorder automatically focuses on
the subject. When it is set, you will hear
a sound and see T mark, then the
camcorder locks the focus.
6 Press the STILL button fully to begin
recording.
• The S indicator flashes red while data
is being recorded on the card, and
returns to white when recording
completes.
AUTO
NORMAL
CARD
/981
7
01
89
0100
-
00
2/2PAGE
1
NORMAL
PLAYBACK
1
4
2
5
3
6
1000
-
00
2/1PAGE
1
NORMAL
PLAYBACK
AUTO
NORMAL
/981
CARD
NORMAL
/981
CARD
3000
-
001
NORMA L
01/3
1000
-
001
NORMAL
01/1
CARD
Card Playback
1 Set the Media Selection
switch to CARD.
2 Hold down the Lock button and set the
Power switch to VCR.
• The images recorded on the card are
displayed in a thumbnail format.
3 Press j, k, l or m on the Operation
button to move the selection frame to
the desired image.
4 Press the SET button.
• The selected image displays in full-
screen.
Number of shots taken/remaining
Lock button
Lock button
Page number/total thumbnail pages
Image file name
ix
Supplied Accessories
Standard-life
battery pack
BT-L225n*
AC adapter
UADP-0339TAZZ*
Audio/video cable
QCNW-1979TAZZ
Lens cap
GCOVH1296TASA
Lens hood
GCOVA1870TASA
Wrist strap
UBNDT0145TASA
Tripod adapter
GDAI-A001WJZZ
USB driver
CDSKA0081TA01
USB cable
QCNW-A338WJZZ
SD Memory Card
VL-NZ100: 8 MB
VL-NZ150: 16 MB
CR2025 type
lithium battery
* The part numbers for the AC adapter and battery pack supplied with this camcorder are valid only in
the U.S. and Latin America. If this camcorder was purchased outside of these areas, the part numbers
may be different. Please refer to the part numbers printed on the labels of the supplied AC adapter and
battery pack.
AA batteryK2
Extended-life
battery pack
BT-L445n*
Remote control
RRMCG0084TASA
For VL-NZ150
For VL-NZ100
Standard-life
battery pack
BT-L225n*
x
Optional Accessories
Note:
• The listed model names are for U.S. accessories.
For optional and additional accessories, contact your local dealer, call the Sharp Accessories and
Supply Center at 1-800-642-2122, or visit SHARP’s website (http://www.sharp-usa.com).
Standard-life
battery pack
BT-L225n
Extended-life
battery pack
BT-L445n
xi
Precautions
• When the camcorder is not in use, remem-
ber to remove the cassette tape, turn off
the power, and disconnect the camcorder
from the power source.
• Do not aim the lens at the sun.
Do not allow direct sunlight to strike the
camcorder lens or LCD monitor screen,
whether or not recording is in progress, as it
may damage the CCD sensor or LCD screen
surface. Be particularly careful when record-
ing outside.
• When shooting in dark places, avoid sudden
brightly lit objects or light sources, such as
the sun. Otherwise, the image may white out.
Should this happen, point the lens in a differ-
ent direction until the picture returns to nor-
mal.
• Avoid magnetic sources.
Using the camcorder near
strong fluorescent lights,
motors, televisions, or other
magnetic sources may ad-
versely affect recorded im-
ages.
• Using the camcorder near a broadcasting
station or other powerful transmission
source may cause buzzing or picture dete-
rioration.
• Avoid shocks and drop-
ping.
Do not drop or otherwise
subject the camcorder to
hard shocks or strong vibra-
tions. Bumping or striking the
unit during recording will
generate noise in the re-
corded image.
• Avoid placing the
camcorder in close
proximity to lighting
equipment.
The heat from incan-
descent lights may de-
form the camcorder, or
cause it to malfunction.
• Always respect prohibitions or restrictions
on the use of electronic equipment on
commercial flights or in other sensitive ar-
eas.
• Be aware of the temperature and humidity.
You can use your camcorder at 32°F to 104°F
(0°C to L40°C), and at 30% to 80% relative
humidity. Do not store
the unit in an
unventilated car in the
summer, in direct sun-
light, or near strong heat
sources; this can result
in severe damage to the
unit casing and circuitry.
• Avoid situations where water, sand, dust or
other foreign matter could get on or inside
the camcorder, and do not use or leave
your camcorder in areas with excessive
smoke, steam or moisture.
Such environments can cause malfunctions
or cause mil-
dew to form on
the lenses. Be
sure to keep the
unit in a well-
ventilated loca-
tion.
• Some small, portable tri-
pods may be difficult to at-
tach and may not be sturdy
enough to support your
camcorder. Be sure to use
only a strong, stable tripod.
• When using your
camcorder in a cold envi-
ronment, the LCD monitor screen often ap-
pears less bright immediately after the
power is turned on. This is not a malfunc-
tion. To prevent the camcorder from be-
coming too cold, wrap it in a thick cloth (a
blanket, etc.).
xii
Part Names .................................................................... 1
On-screen Display Index ............................................... 4
Warning Indicators ......................................................... 7
Contents
Operation References
Preparation
Basic Operations
Useful Features
Attaching and Removing the Battery Pack .................... 9
Charging the Battery Pack ........................................... 10
Powering the Camcorder from an AC Outlet ............... 11
Inserting and Removing a Cassette ............................ 12
Inserting and Removing a Card ................................... 13
Installing the Lithium Battery ........................................ 14
Selecting the Language for the On-screen Display..... 15
Setting the Date and Time ........................................... 16
Attaching the Lens Hood ............................................. 17
Attaching the Wrist Strap ............................................. 17
Using the Lens Cap ..................................................... 17
Tips on Recording Positions ........................................ 18
Camera Recording
Selecting the Camcorder Mode ................................... 19
Easy Camera Recording on Tape
in Full Auto Mode ....................................................... 20
Zooming ....................................................................... 21
Auto Focus ................................................................... 21
Macro Shots ................................................................. 21
Remaining Recording Time Display ............................ 22
Remaining Battery Power Display ............................... 22
Playback
Tape Playback ............................................................. 23
Volume Control ............................................................. 23
Video Search ................................................................ 24
Still ............................................................................... 24
Watching Playback on a TV ......................................... 25
Using the Menu Screens.............................................. 26
Camera Recording
Displaying the Recording Guide .................................. 27
Setting the Digital Zoom .............................................. 28
Gamma Brightness Compensation .............................. 29
Gain-up ........................................................................ 30
Fade In and Fade Out .................................................. 31
Quick Return ................................................................ 32
Edit Search................................................................... 32
Appendix
Preparation
Useful Features
Operation References
Basic Operations
Advanced Features
Digital Still Camera
Features
xiii
Useful Features
Still Recording on Tape ................................................ 33
Attaching the Supplied Tripod Adapter ....................... 33
Wide Screen (16:9) ...................................................... 34
Digital Image Stabilization (DIS) .................................. 34
Self Recording ............................................................. 35
Recording in LP (Long Play Recording) Mode ............ 36
Selecting the 16-bit Audio Recording Mode................ 37
Playback
Using the Remote Control ............................................ 38
Displaying the Date and Time of Recording ................ 39
Slow ............................................................................. 39
Gamma Playback ........................................................ 40
Copying an Image from Tape to Card ......................... 40
Picture Effect Playback ................................................ 41
Contents
Advanced Features
Camera Recording
Manual Focus .............................................................. 42
Manual Exposure ......................................................... 43
White Balance Lock ..................................................... 44
Setting the Camcorder to Full Auto Mode.................... 44
Digital Picture Effects ................................................... 45
Scene Menu (Program AE) .......................................... 46
Playback
Using the Time Code ................................................... 47
Editing .......................................................................... 48
Recording from an External Source ............................. 49
Using the Camcorder as a Converter .......................... 50
Editing with the DV Terminal (IEEE1394) ..................... 51
Selecting the Audio Playback Mode ............................ 52
Audio Dubbing Feature................................................ 53
xiv
Appendix
Preparation
Useful Features
Operation References
Basic Operations
Advanced Features
Digital Still Camera
Features
Digital Still Camera
Features
Camera Recording
Card Recording ........................................................... 55
Selecting the Picture Quality ........................................ 56
Recording with the Self-timer ....................................... 57
Formatting a Card ........................................................ 58
Playback
Card Playback ............................................................. 59
Delete Protection.......................................................... 60
Deleting Stored Images ............................................... 61
Print Order .................................................................... 63
Transferring Data on Card to Computer ...................... 65
Installing the USB driver ......................................... 65
Slide Show Playback ................................................... 67
Picture/Backlight Adjustments ..................................... 68
Turning off the Confirmation Sound ............................. 69
Useful Information ........................................................ 70
Demonstration Mode ................................................... 79
Before Requesting Service .......................................... 80
Specifications .............................................................. 82
• Guía de operación rápida en español ..................................................................... 83
• Visualizaciones en pantalla en español ................................................................... 91
• Affichages sur écran en français.............................................................................. 93
Appendix
Operation References
Operation References
1
Operation References
Part Names
For details on the use of each part, refer to the page number indicated in brackets.
Operation References
2
Rear view
USB terminal
[pp. 65, 66]
DV terminal
[pp. 50, 51]
AV jack
[pp. 25, 48-50]
Media Selection
switch (TAPE/
CARD selection
switch) [p. 19]
Operation button
Jack cover
[pp. 25,
48-51, 65]
Power Zoom Wide angle/
Telephoto control [p. 21]/
VOLume control [p. 23]
LCD monitor
Operation References
Operation References
3
Rear view
Bottom view
Operation References
4
On-screen Display Index
For details on the use of each function, refer to the page number indicated.
AUTO
30
min
CLOCK SET
DISPLAY
RETURN
LCD SET
BACKL I GHT
LCD BRI GHT
LCD COLOR
RETURN
LCD SET
BACKL I GHT
LCD BRI GHT
LCD COLOR
RETURN
AUDIOAUDIO
21
+
21
+
CLOCK SET
DISPLAY
SETTING
12H 24H/
RETURN
EFFECT
PLAYBACK
PIC.
AUDI O DUB
AUDI O
ANLG DGTL
RETURN
SET
OTHERS
BEEP
REMOTE
T IME CODE
TC OUT
RETURN
EFFECTPIC.
SCENE MENU
QK.
RETURN
GU I DE
RETURN
EFFECT
PLAYBACK
PIC.
AUDI O DUB
AUDI O
ANLG DGTL
RETURN
SET
SETT ING 1
DGTL ZOOM
TAPE
DIS
SPEED
16 9:
AUDI O MODE
RETURN
EFFECTPIC.
SCENE MENU
QK.
RETURN
GU I DE
RETURN
OTHERS
BEEP
T IME CODE
TC OUT
DEMO
LANGUAGE
RETURN
MODE
SETTING 1
SETTING 2
TAPE-CAMERA mode
TAPE-VCR mode
p. 22
pp. 20, 44
p. 34
p. 20
p. 22
p. 22
p. 52
p. 45
p. 46
p. 32
p. 27
p. 28
p. 36
p. 34
p. 34
p. 37
p. 69
p. 47
p. 47
p. 79
p. 15
p. 68
p. 39
p. 16
p. 17
p. 41
p. 54
p. 52
p. 50
p. 38
p. 69
p. 47
p. 47
p. 68
p. 39
Operation References
Operation References
5
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Sharp VL-NZ100U User manual

Category
Camcorders
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI