Denon DHT-485XP User manual

Brand: Denon

Model: DHT-485XP

Category: AV receivers

Type: User manual

This manual is also suitable for

We greatly appreciate your purchase of this unit.

To be sure you take maximum advantage of all the

features this unit has to offer, read these instructions

carefully and use the set properly. Be sure to keep this

manual for future reference should any questions or

problems arise.

“SERIAL NO.

PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO

THE REAR OF THE CABINET FOR FUTURE REFERENCE”

“NO. DE SERIE

PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL

INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR

LE CONSULTER EN CAS DE PROBLEME.”

Nous vous remercions pour l’achat de cet appareil.

Pour être sûr de profiter au maximum de toutes les

caractéristiques qu’offre cet appareil, lire avec soin ces

instructions et bien utiliser l’appareil. Toujours

conserver ce mode d’emploi pour s’y référer

ultérieurement en cas de question ou de problème.

FOR ENGLISH READERS PAGE 2 ~ PAGE 64, 126 ~ 130 POUR LES LECTEURS FRANCAIS PAGE 2, 65 ~ PAGE 130

AV SURROUND RECEIVER

RÉCEPTEUR AUDIO-VIDÉO

AVR-485S

OPERATING INSTRUCTIONS

MODE D’EMPLOI

ENGLISH FRANCAIS

2 SAFETY PRECAUTIONS

2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION

•Avoid high temperatures.

Allow for sufficient heat dispersion when

installed on a rack.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur

suffisante lors de l’installation sur une étagère.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Keep the set free from moisture, water, and

dust.

•Protéger l’appareil contre l’humidité, l’eau et la

poussière.

• Unplug the power cord when not using the set

for long periods of time.

• Débrancher le cordon d’alimentation lorsque

l’appareil n’est pas utilisé pendant de longues

périodes.

* (For sets with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• Do not let foreign objects in the set.

• Ne pas laisser des objets étrangers dans

l’appareil.

• Do not let insecticides, benzene, and thinner

come in contact with the set.

•Ne pas mettre en contact des insecticides, du

benzène et un diluant avec l’appareil.

• Never disassemble or modify the set in any

way.

• Ne jamais démonter ou modifier l’appareil

d’une manière ou d’une autre.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

CAUTION

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG

TO WIDE SLOT, FULLY INSERT.

ATTENTION

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA

LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU

FOND.

•

FOR CANADA MODEL ONLY

•

POUR LES MODELE CANADIEN UNIQUEMENT

1. PRODUCT

This product complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) this product may not cause harmful

interference, and (2) this product must accept any interference received,

including interference that may cause undesired operation.

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained in this

manual, meets FCC requirements. Modification not expressly approved by

DENON may void your authority, granted by the FCC, to use the product.

3. NOTE

This product has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation.

This product generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

product does cause harmful interference to radio or television reception,

which can be determined by turning the product OFF and ON, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the product into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the local retailer authorized to distribute this type of product or

an experienced radio/TV technician for help.

FCC INFORMATION (For US customers)

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2. Retain Instructions – The safety and operating instructions

should be retained for future reference.

3. Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should

be followed.

5. Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

6. Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water – for

example, near a bath tub, wash bowl, kitchen sink, or laundry

tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall, causing

serious injury to a child or adult, and serious damage to the

product. Use only with a cart, stand, tripod, bracket, or table

recommended by the manufacturer, or sold with the product.

Any mounting of the product should follow the manufacturer’s

instructions, and should use a

mounting accessory

recommended by the

manufacturer.

9. A product and cart

combination should be

moved with care. Quick

stops, excessive force,

and uneven surfaces may

cause the product and cart

combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for

ventilation and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not be

blocked or covered. The openings should never be blocked by

placing the product on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in installation such

as a bookcase or rack unless proper ventilation is provided or

the manufacturer’s instructions have been adhered to.

11. Power Sources – This product should be operated only from the

type of power source indicated on the marking label. If you are

not sure of the type of power supply to your home, consult your

product dealer or local power company. For products intended

to operate from battery power, or other sources, refer to the

operating instructions.

12. Grounding or Polarization – This product may be equipped with

a polarized alternating-current line plug (a plug having one blade

wider than the other). This plug will fit into the power outlet

only one way. This is a safety feature. If you are unable to

insert the plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of the

polarized plug.

13. Power-Cord Protection – Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to

cords at plugs, convenience receptacles, and the point where

they exit from the product.

15. Outdoor Antenna Grounding – If an outside antenna or cable

system is connected to the product, be sure the antenna or

cable system is grounded so as to provide some protection

against voltage surges and built-up static charges. Article 810

of the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding conductors, location

of antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode. See Figure A.

16. Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line surges.

17. Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other electric

light or power circuits, or where it can fall into such power lines

or circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

18. Overloading – Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a risk of

fire or electric shock.

19. Object and Liquid Entry – Never push objects of any kind into

this product through openings as they may touch dangerous

voltage points or short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind on the product.

20.

Servicing – Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

21.

Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service

personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance

– this indicates a need for service.

22. Replacement Parts – When replacement parts are required, be

sure the service technician has used replacement parts

specified by the manufacturer or have the same characteristics

as the original part. Unauthorized substitutions may result in

fire, electric shock, or other hazards.

23. Safety Check – Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

24. Wall or Ceiling Mounting – The product should be mounted to a

wall or ceiling only as recommended by the manufacturer.

25. Heat – The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE

ANTENNA

LEAD IN

WIRE

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC - NATIONAL ELECTRICAL CODE

ENGLISH

2 INTRODUCTION

2 ACCESSORIES

Thank you for choosing the DENON A/V Surround receiver. This remarkable component has been engineered to provide superb surround sound

listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.

As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the

contents of this manual before proceeding.

TABLE OF CONTENTS

Check that the following parts are included in addition to the main unit:

BEFORE USING

Pay attention to the following before using this unit:

• Moving the set

To prevent short circuits or damaged wires in the connection cords,

always unplug the power cord and disconnect the connection

cords between all other audio components when moving the set.

• Before turning the power operation switch on

Check once again that all connections are proper and that there are

not problems with the connection cords. Always set the power

operation switch to the standby position before connecting and

disconnecting connection cords.

• Store this instructions in a safe place.

After reading, store this instructions along with the warranty in a

safe place.

• Note that the illustrations in this instructions may differ from

the actual set for explanation purposes.

• V. AUX terminal

The AVR-1505/485’s front

panel is equipped with a V.

AUX terminal. Remove the

cap covering the terminal

when you want to use it.

Before Using ..............................................................................................4

Cautions on Installation..............................................................................5

Cautions on Handling .................................................................................5

Features......................................................................................................6

Part Names and Functions....................................................................7, 8

Read this first.............................................................................................9

Setting up the Speaker Systems................................................................9

Connections.....................................................................................10 ~ 16

Using the Remote Control Unit................................................................17

⁄0

Setting up the System.....................................................................18 ~ 27

⁄1

Remote Control Unit..........................................................................28~32

⁄2

Operation ...........................................................................................33~37

⁄3

Surround.............................................................................................38~46

⁄4

DSP Surround Simulation...................................................................47~51

⁄5

Listening to the Radio……………………………………………………52~54

⁄6

Last Function Memory.............................................................................55

⁄7

Initialization of the Microprocessor.…………………………………………55

⁄8

Additional Information........................................................................56~62

⁄9

Troubleshooting........................................................................................63

¤0

Specifications .…………………………………………………………………64

List of Preset Codes..............................................................................126~130

q Operating instructions ............................................................................1

w Warranty .................................................................................................1

e Service station list...................................................................................1

r Remote control unit (RC-977).................................................................1

rt y u

t R6P/AA batteries ....................................................................................2

y AM loop antenna ....................................................................................1

u FM indoor antenna..................................................................................1

ENGLISH

CAUTIONS ON HANDLING

• Switching the input function when input jacks are not

connected

A clicking noise may be produced if the input function is switched

when nothing is connected to the input jacks. If this happens,

either turn down the MASTER VOLUME control or connect

components to the input jacks.

• Muting of PRE OUT jack, HEADPHONE jack and SPEAKER

terminals

The PRE OUT jack, HEADPHONE jack and SPEAKER terminals

include a muting circuit. Because of this, the output signals are

greatly reduced for several seconds after the power operation

switch is turned on or input function, surround mode or any other

set-up is changed.

If the volume is turned up during this time, the output will be very

high after the muting circuit stops functioning. Always wait until

the muting circuit turns off before adjusting the volume.

• Whenever the unit is in the STANDBY state, the apparatus is

still connected on AC line voltage.

Please be sure to turn the power off (

£ off) when you leave

home for, say, a vacation.

CAUTIONS ON INSTALLATION

Noise or disturbance of the picture may be generated if this unit or

any other electronic equipment using microprocessors is used near a

tuner or TV.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this unit’s

power cord and input/output connection cords.

• Noise or disturbance tends to occur particularly when using indoor

antennas or 300 Ω/ohms feeder wires. We recommend using

outdoor antennas and 75 Ω/ohms coaxial cables.

For heat dispersal, leave at least 0.3 ft (10 cm) of space between

the top, back and sides of this unit and the wall or other

components.

0.3 ft (10 cm) or more

Wall

0.3 ft (10 cm) or more

ENGLISH

FEATURES

1. Dolby Digital

Using advanced digital processing algorithms, Dolby Digital

provides up to 5.1 channels of wide-range, high fidelity surround

sound. Dolby Digital is the default digital audio delivery system for

DVD and North American DTV.

2. Dolby Pro Logic

IIx compatibility

Dolby Pro Logic IIx furthers the matrix decording technology of

Dolby Pro Logic II to decode audio signals recorded on two

channels into up to 6.1 playback channels, including the surround

back channel.

The mode can be selected according to the source. The Music

mode is best suited for playing music,the Cinema mode for

playing movies, and the Game mode for playing games. The

Game mode can only be used with 2-channel audio sources.

3. Dolby Pro Logic

II Game mode compatibility

In addition to the previously offered Music and Cinema modes,

the AVR-1505/485 also offers a Game mode optimum for games.

4. DTS (Digital Theater Systems)

DTS provides up to 5.1 channels of wide-range, high fidelity

surround sound, from sources such as laser disc, DVD and

specially-encoded music discs.

5. DTS-ES Extended Surround and DTS Neo:6

The AVR-1505/485 can be decoded with DTS-ES Extended

Surround, a multi-channel format developed by Digital Theater

Systems Inc.

The AVR-1505/485 can be also decoded with DTS Neo:6, a

surround mode allowing 6.1 channels playback of regular stereo

sources.

6. DTS 96/24 compatibility

The AVR-1505/485 can be decoded with sources recorded in DTS

96/24, a multi-channel digital signal format developed by Digital

Theater Systems Inc.

DTS 96/24 sources can be played in the multi-channel mode on

the AVR-1505/485 with high sound quality of 96 kHz/24 bits or

88.2 kHz/24 bits.

7. Component Video Switching

In addition to composite video and “S” video switching, the AVR-

1505/485 provides 3 sets of component video (Y, PB/CB, PR/CR)

inputs, and one set of component video outputs to the television,

for superior picture quality.

8. Auto Surround Mode

This function stores the surround mode last used for an input

signal in the memory and automatically sets that surround mode

the next time that signal is input.

9. Front input terminal

The unit is equipped with a Front Input connector for the

convenient connection of a video camera or other equipment.

10.6CH EXT. IN jacks

This unit is equipped with 6CH EXT. IN jacks for use with audio

formats of the future.

11.Personal Memory Plus function

Persinal Memory Plus is an advanced version of Personal

Memory. With Personal Memory Plus, the set automatically

memorizes the surround mode, channel volume, surround

parameters, etc., for each of the separate input sources.

12.Preset Memory Tuning

56-Station AM/FM Random Preset Memory tuning.

PART NAMES AND FUNCTIONS

Front Panel

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

@1@2@3@4@5@6@7@8

!5 !6 !7

#0#1#2

Power ON/STANDBY switch.......................................(19, 33, 52)

POWER indicator...............................................................(19, 33)

Power switch.....................................................................(19, 33)

Headphone jack (PHONES) .....................................................(36)

INPUT MODE button ........................................................(34, 37)

SPEAKER A/B buttons.......................................................(33, 55)

SURROUNDBACK button........................................................(44)

EXT. IN button ...................................................................(34, 37)

BAND button ...........................................................................(53)

STANDARD button................................................(38, 40, 42, 44)

5CH/6CH STEREO button .......................................................(48)

DIRECT/STEREO button..........................................................(47)

Preset station select buttons...................................................(54)

TUNING • (up) / ª (down) buttons..........................................(53)

V. AUX terminals..................................................................(4, 12)

SURROUND MODE button.....................................................(35)

SURROUND PARAMETER button.....................................(40, 48)

SELECT knob...............................................................(35, 40, 50)

TONE DEFEAT button .............................................................(35)

TONE CONTROL button..........................................................(35)

MASTER VOLUME control......................................................(35)

STATUS button ........................................................................(36)

DIMMER button ......................................................................(36)

VIDEO SELECT button ............................................................(36)

SURROUND BACK indicator ...................................................(44)

MASTER VOLUME indicator...................................................(35)

Display

INPUT mode indicators............................................................(35)

SIGNAL indicators....................................................................(35)

ANALOG button ................................................................(34, 37)

Remote control sensor (REMOTE SENSOR) ..........................(17)

INPUT SELECTOR knob..........................................................(34)

ENGLISH

NOTE:

• The shaded buttons do not function with the AVR-

1505/485. (Nothing happens when they are pressed.)

Remote control unit

• For details on the functions of these parts, refer to the pages given in parentheses ( ).

SURROUND

buttons...................................(35, 38, 48)

Cursor

buttons.............................(18, 30, 31, 40)

STATUS/DISPLAY button.......(30, 31, 36)

Test tone button.................................(38)

Remote control signal

transmitter .........................................(17)

Master volume control

buttons...............................................(35)

POWER buttons..............(19, 29~31, 33)

MUTING button .................................(36)

Mode selector switches........(28~30, 32)

Tuner system/

System buttons ...............(28, 30, 31, 53)

SYSTEM SET UP/

SETUP button........................(18, 30, 31)

INPUT MODE selector

buttons.........................................(34, 37)

Input source selector

buttons ..................................(29~32, 34)

SURROUND PARAMETER

button ....................................(30, 31, 40)

CH SELECT (channel select)/

ENTER button............(18, 30, 31, 39, 41)

SURROUND BACK/

RETURN button.....................(30, 31, 44)

SPEAKER select button.....................(33)

DIMMER button.................................(36)VIDEO SELECT button.......................(36)

System buttons .....................(28, 30, 31)

LED (indicator) .............................(29, 32)

ENGLISH

READ THIS FIRST

This AV Surround Receiver must be setup before use. Following these steps.

SETTING UP THE SPEAKER SYSTEMS

Step 3 (page 18 to 27)

Finally, setting up the system.

Step 2 (page 17)

Next, insert the batteries into the remote control unit.

Step 1 (page 9 to 16)

Choose the best location to setup the Speakers and connecting the components.

2 Speaker system layout

Basic system layout

• The following is an example of the basic layout for a system consisting of seven speaker systems and a television monitor:

Subwoofer Center speaker system

Surround speaker systems

Surround back speaker system

Front speaker systems

Set these at the sides of the TV or screen with

their front surfaces as flush with the front of the

screen as possible.

ENGLISH

CONNECTIONS

• Do not plug in the power cord until all connections have been

completed.

• Be sure to connect the left and right channels properly (left with

left, right with right).

• Insert the plugs securely. Incomplete connections will result in

the generation of noise.

• Use the AC OUTLETS for audio equipment only. Do not use

them for hair driers, etc.

• Note that binding pin plug cords together with power cords or

placing them near a power transformer will result in generating

hum or other noise.

• Noise or humming may be generated if a connected audio

equipment is used independently without turning the power of

this unit on. If this happens, turn on the power of the this unit.

Connecting the audio components

LINE OUT

SURROUND

SUB WOOFER

CENTER

FRONT

LINE OUT

LINE IN

OUTPUTINPUT

LRL

OUTPUT

DIGITAL AUDIODIGITAL AUDIO

INPUTOUTPUT

OPTICAL

Connecting a CD player

Connect the CD player’s analog output jacks

(ANALOG OUTPUT) to this unit’s CD jacks using

pin plug cords.

Decoders with 6-channel

analog outputs, etc.

DIGITAL jacks

Use these for connections to audio equipment with digital output.

Refer to page 26 for instructions on setting this terminal.

Connecting the AC OUTLETS

AC OUTLETS

• SWITCHED

(total capacity – 120 W (1 A.))

The power to these outlets is turned on and off in conjunction with the POWER switch

on the main unit, and when the power is switched between on and standby from the

remote control unit.

No power is supplied from these outlets when this unit’s power is at standby. Never

connect equipment whose total capacity is above 120 W (1 A.)

NOTE:

Only use the AC OUTLETS for audio equipment. Never use them for hair driers, TVs or

other electrical appliances.

AC CORD

AC 120V, 60Hz

Connect the internal amplifier’s subwoofer to the subwoofer

terminal. (Refer to page 15.)

Connecting a tape deck

Connections for recording:

Connect the tape deck’s recording input jacks (LINE IN or REC)

to this unit’s tape recording (OUT) jacks using pin plug cords.

Connections for playback:

Connect the tape deck’s playback output jacks (LINE OUT or

PB) to this unit’s tape playback (IN) jacks using pin plug cords.

CD player

Tape deck or CD recorder

• Use 75 Ω/ohms cable pin cords (sold separately) for coaxial

connections.

• Use optical cables (sold separately) for optical connections.

Subwoofer jack

CD recorder, MD recorder or other component

equipped with digital output jacks.

ENGLISH

Connecting the video equipments

To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in sound quality.

R OUT

VIDEO

OPTICAL

OUT

AUDIO

OUT

DIGITAL

VIDEO

R OUT IN

AUDIO

VIDEO

OUT IN

LRL

R OUT

VIDEO

OPTICAL

OUT

AUDIO

OUT

DIGITAL

AUDIO OUT

VIDEO OUT

VIDEO IN

AUDIO OUT

VIDEO OUT

AUDIO OUT

AUDIO IN

VIDEO IN

VIDEO OUT

TV or DBS tuner

DVD player or VDP

Monitor TV

Connecting a TV/DBS tuner

TV/DBS

• Connect the TV’s or DBS tuner’s video output jack

(VIDEO OUTPUT) to the (yellow) TV/DBS IN

jack using a 75 Ω/ohms video coaxial pin plug cord.

• Connect the TV’s or DBS tuner’s audio output jacks

(AUDIO OUTPUT) to the TV/DBS IN jacks

using pin plug cords.

AUDIO

VIDEO

Connecting a DVD player or a video disc player (VDP)

• Connect the DVD player’s (video disc player’s) video output jack (VIDEO OUTPUT)

to the (yellow) DVD/VDP IN jack using a 75 Ω/ohms video coaxial pin plug

cord.

• Connect the DVD player’s (video disc player’s) analog audio output jacks

(ANALOG AUDIO OUTPUT) to the DVD/VDP IN jacks using pin plug

cords.

• For better sound quality, we recommend using the DVD player with digital rather

than analog connections.

DVD and VDP players can also be connected to the VCR terminals.

AUDIO

VIDEO

MONITOR OUT

• Connect the TV’s video input jack (VIDEO

INPUT) to the MONITOR OUT jack

using a 75 Ω/ohms video coaxial pin plug

cord.

VIDEO

NOTE:

Connection of the video disc Player Equipped with Dolby Digital RF Output

jack.

• Please use a commercially available adaptor when connecting the Dolby

Digital RF output jack of the video disc player to the digital input jack.

Please refer to the instruction manual of the adapter when making

connections.

Video deck

Video input/output connections:

• Connect the video deck’s video output jack (VIDEO OUT) to the (yellow) VCR IN jack, and the video deck’s video input jack (VIDEO IN) to the (yellow)

VCR OUT jack using 75 Ω/ohms video coaxial pin plug cords.

Connecting the audio output jacks:

• Connect the video deck’s audio output jacks (AUDIO OUT) to the VCR IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the VCR OUT

jacks using pin plug cords.

AUDIOAUDIO

VIDEOVIDEO

Connecting a video decks

ENGLISH

Connecting a video component equipped with S-video jacks

• When marking connections, also refer to the operating instructions of the other components.

• A note on the S input jacks

The input selectors for the S inputs and pin jack inputs work in conjunction with each other.

• Precaution when using S-jacks

This unit’s S-jacks (input and output) and video pin jacks (input and output) have independent circuit structures, so that video signals input from

the S-jacks are only output from the S-jack outputs and video signals input from the pin jacks are only output from the pin jack outputs.

When connecting this unit with equipment that is equipped with S-jacks, keep the above point in mind and make connections according to the

equipment’s instruction manuals.

S-VIDEO

OUT

S-VIDEO

OUT

S-VIDEO

OUT IN

S-VIDEO

VIDEO IN

VIDEO OUT

VIDEO IN

VIDEO OUT

DVD player, VDP, etc.

Connecting a DVD player or video disc player (VDP)

DVD/VDP

• Connect the DVD player’s or video disc player’s S-video

output jack to the S-VIDEO DVD/VDP IN jack using an S-

video connection cord.

Connecting a monitor TV

MONITOR OUT

• Connect the TV’s or DBS tuner’s S video input (S-

VIDEO INPUT) to the MONITOR OUT

jack using a S jack connection cord.

S-VIDEO

Monitor TV

Connecting a TV/DBS tuner

• Connect the TV’s or DBS tuner’s S-video output jack (S-VIDEO

OUTPUT) to the TV/DBS IN jack using an S jack

connection cord.

S-VIDEO

TV or satellite broadcast tuner

Video deck

Connecting the video decks

• Connect the video deck’s S output jack (S-OUT) to the VCR IN

jack and the video deck’s S input jack (S-IN) to the VCR OUT

jack using S jack connection cords.

S-VIDEO

Connect the components’ audio inputs and outputs as described on page 11.

R VIDEO OUTL

OUTPUT

R VIDEO OUTL

OUTPUT

LINE OUT

VIDEO OUT

LINE OUT

Connecting a Video game equipment

• Connect the Video game equipment’s output jacks to this

unit’s V. AUX INPUT jacks.

Video game

Video camera

Connecting a Video camera equipment

• Connect the video camera equipment’s output jacks to this

unit’s V. AUX INPUT jacks.

The V. AUX terminal is covered with a cap. Remove this

cap in order to use the terminal. (See page 4 for instructions

on removing the cap.)

ENGLISH

VIDEO OUT

CRCB

COMPONENT

YCRCB

VIDEO IN

COMPONENT

Connecting a Video Component Equipped with Color Difference (Component - Y, P

, P

)

Video Jacks (DVD Player)

• When making connections, also refer to the operating instructions of the other components.

• The signals input to the color difference (component) video jacks are not output from the VIDEO output jack (yellow) or the S-Video output jack.

• Some video sources with component video outputs are labeled Y, C

B, CR, or Y, Pb, Pr, or Y, R-Y, B-Y. These terms all refer to component video

color difference output.

DVD player

Connecting a DVD player

DVD IN jacks

• Connect the DVD player’s color difference (component) video output jacks

(COMPONENT VIDEO OUTPUT) to the COMPONENT DVD IN jack using 75 Ω/ohms

coaxial video pin-plug cords.

• In the same way, another video source with component video outputs such as a TV/DBS

tuner, etc., can be connected to the TV/DBS color difference (component) video jacks.

Monitor TV

Connecting a monitor TV

MONITOR OUT jack

• Connect the TV’s color difference (component) video input jacks (COMPONENT VIDEO

INPUT) to the COMPONENT MONITOR OUT jack using 75 Ω/ohms coaxial video pin-

plug cords.

• The color difference input jacks may be indicated differently on some

TVs, monitors or video components (“CR, CB and Y”, “R-Y, B-Y and Y”,

“Pr, Pb and Y”, etc.). For details, carefully read the operating instructions

included with the TV or other component.

ENGLISH

Connecting the antenna terminals

DIRECTION OF

BROADCASTING

STATION

AM LOOP

ANTENNA

(An Accessory)

FM ANTENNA

GROUND

AM OUTDOOR

ANTENNA

FM INDOOR

ANTENNA

(An Accessory)

75 Ω/ohms

COAXIAL

CABLE

AM loop antenna assembly

Connect to the AM

antenna terminals.

Bend in the reverse

direction.

Remove the vinyl tie

and take out the

connection line.

a. With the antenna

on top any stable

surface.

b. With the antenna

attached to a

wall.

Mount

Installation hole Mount on wall, etc.

Connection of AM antennas

1. Push the lever. 2. Insert the

conductor.

3. Return the lever.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of cable entry as practical.

NOTES:

• Do not connect two FM antennas simultaneously.

• Even if an external AM antenna is used, do not disconnect the

AM loop antenna.

• Make sure AM loop antenna lead terminals do not touch metal

parts of the panel.

ENGLISH

Speaker system connections

• Connect the speaker terminals with the speakers making sure that

like polarities are matched (< with <, > with >). Mismatching of

polarities will result in weak central sound, unclear orientation of

the various instruments, and the sense of direction of the stereo

being impaired.

• When making connections, take care that none of the individual

conductors of the speaker cord come in contact with adjacent

terminals, with other speaker cord conductors, or with the rear

panel.

Speaker Impedance

• When speaker systems A and B are use separately, speakers with

an impedance of 6 to 16 Ω/ohms can be connected for use as front

speakers.

• Be careful when using two pairs of front speakers (A + B) at the

same time, since use of speakers with an impedance of 12 to 16

Ω/ohms.

• Speakers with an impedance of 6 to 16 Ω/ohms can be connected

for use as center and surround and surround back speakers.

•The protector circuit may be activated if the set is played for long

periods of time at high volumes when speakers with an impedance

lower than the specified impedance are connected.

NOTE:

NEVER touch the speaker terminals when the power is on.

Doing so could result in electric shocks.

Connecting the speaker cords

1. Loosen by turning

counterclockwise.

2. Insert the cord. 3. Tighten by turning

clockwise.

Connecting banana plugs

Turn clockwise to tighten, then insert the

banana plug.

Banana plug

(

)(

)

(

) (

)(

) (

)

Connection jack for subwoofer with built-in amplifier

(super woofer), etc.

To achieve Dolby Digital playback effect, use a unit

that can sufficiently reproduce frequencies of

under 80 Hz.

SURROUND SPEAKER SYSTEMS

CENTER SPEAKER SYSTEM FRONT SPEAKER SYSTEMS

• Precautions when connecting speakers

If a speaker is placed near a TV or video monitor, the colors on the screen may be disturbed by

the speaker’s magnetism. If this should happen, move the speaker away to a position where

it does not have this effect.

System B

FRONT SPEAKER SYSTEMS

System A

SURROUND BACK SPEAKER SYSTEM

ENGLISH

Protector circuit

• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under

circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows,

when the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long

period which results in an extreme temperature rise.

When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should

this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with

the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation

condition around the unit and switch the power back on.

If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the

unit, switch off the power and contact a DENON service center.

Note on speaker impedance

• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with

an impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms)

are connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set

to cool down, improve the ventilation around the set, then turn the power back on.

ENGLISH

USING THE REMOTE CONTROL UNIT

Following the procedure outlined below, insert the batteries before using the remote control unit.

Range of operation of the remote control unit

Inserting the batteries

Point the remote control unit at the remote control sensor as shown

on the diagram at the left.

NOTES:

• The remote control unit can be used from a straight distance of

approximately 23 feet/7 meters, but this distance will shorten or

operation will become difficult if there are obstacles between the

remote control unit and the remote control sensor, if the remote

control sensor is exposed to direct sunlight or other strong light, or

if operated from an angle.

• Neon signs or other devices emitting pulse-type noise nearby may

result in malfunction, so keep the set as far away from such

devices as possible.

Approx. 23 feet/7 m

30°

w Insert the R6P/AA batteries properly, as

shown on the diagram.

q Press as shown by the arrow and slide off. e Close the lid.

NOTES:

• Use only R6P/AA batteries for replacement.

• Be sure the polarities are correct. (See the illustration inside the battery compartment.)

• Remove the batteries if the remote control transmitter will not be used for an extended period of time.

• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the

battery compartment thoroughly before installing new batteries.

•Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.

• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is

operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)

ENGLISH

SETTING UP THE SYSTEM

• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 10 to 16), make the

various settings described below on the display.

These settings are required to set up the listening room’s AV system centered around the this unit.

SYSTEM SETUP button

Press this to display the system setup on the display.

CURSOR buttons (•, ª, 0, 1)

Press this change what appears on the display.

ENTER button

Press this to switch the display.

Also use this button to complete the setting.

• System setup items and default values (set upon shipment from the factory)

System setup Default settings

Speaker

Configuration

Subwoofer Mode

Digital In

Assignment

Input the combination of speakers in your system and their

corresponding sizes (SMALL for regular speakers, LARGE for full-size,

full-range) to automatically set the composition of the signals output

from the speakers and the frequency response.

This assigns the digital input jacks for the different input

sources.

Input

source

Digital

Inputs

Front Sp.

Large

Center Sp. Surround Sp. Subwoofer

Small Small Yes

CD DVD/VDP

COAXIAL OPTICAL

Delay Time

This parameter is for optimizing the timing with which the audio

signals are produced from the speakers and subwoofer according to

the listening position.

Set the slide switch to “AUDIO”.

Use the following buttons to set up the system:

This selects the subwoofer speaker for playing deep bass signals. Subwoofer mode = Normal

NOTE:

• The system setup is not displayed when “HEADPHONE ONLY” is selected.

Crossover

Frequency

Set the frequency (Hz) below which the bass sound of the various

speakers is to be output from the subwoofer.

80 Hz

Auto Surround

Mode

Auto surround mode function setting. Auto Surround Mode = ON

Ext. In SW Level Set the Ext. In Subwoofer channel playback level. Ext. In SW Level = +15 dB

Surround back Sp.

Small

Front L Center Surround Back

12 ft 12 ft 10 ft

Subwoofer

12 ft

Front R

12 ft

Surround L

10 ft

Surround R

10 ft

Front L Front R Center

0 dB 0 dB 0 dB

Test Tone

This adjusts the volume of the signals output from the speakers and

subwoofer for the different channels in order to obtain optimum

effects.

Surround L

0 dB

Surround R

0 dB

Surround Back

0 dB

Subwoofer

0 dB

ENGLISH

Before setting up the system

Press the SYSTEM SETUP button to enter the setting.

Turn on the power.

Press the Power ON/STANDBY switch (button).

Press the ENTER or (down) button to switch to the speaker configuration set up.

*SYSTEM SET UP

NOTE:

Press the SYSTEM SETUP button again to finish system set up. System set up can be finished at any time. The changes to the settings

made up to that point are entered.

NOTE: Please make sure the “AUDIO” position of the slide switch on the remote control unit.

(Main unit) (Remote control unit)

Setting the speaker configuration

Use the (left) and (right) buttons to select your front speaker type.

1 FRONT LARGE

LARGE

SMALL

(left) button (right) button

Press the ENTER or (down) button to switch to the center speaker setting.

Use the (left) and (right) buttons to select your center speaker type.

2 CENTER SMALL

LARGE

SMALL

NONE

(left) button (right) button

Press the ENTER or (down) button to switch to the surround speaker setting.

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the center speaker.

(Initial)

Press the Power switch (button) .

(Main unit)

• ¢ ON

The power turns on and indicator is light.

Set the power switch to this position to turn the power on and off from the included remote control unit.

• £ OFF

The power turns off and indicator is off.

In this position, the power cannot be turned on and off from the remote control unit.

ENGLISH

Refer to “CONNECTIONS” (pages 10 to 16) and check that all connections are correct.

Use the (left) and (right) buttons to select your subwoofer setting.

5 S.WOOFER YES

YES

(left) button (right) button

Press the ENTER or (down) button to enter the settings and switch to the Speaker Distance setting.

• Parameters

Large…… Select this when using speakers that have sufficient performance for reproducing bass sound below the frequency set for the

Crossover Frequency mode.

Small…… Select this when using speakers that do not have sufficient performance for reproducing bass sound below the frequency set for

the Crossover Frequency mode. When this is set, bass sound with a frequency below the frequency set for the Crossover

Frequency mode is sent to the subwoofer.

None…… Select this when no speakers are installed.

Yes/No…. Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.

If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when “Small” is set for the front, center

and surround speakers.

(Initial)

Use the (left) and (right) buttons to select your surround back speaker type.

4 S.BACK SMALL

LARGE

SMALL

NONE

(left) button (right) button

Press the ENTER or (down) button to switch to the subwoofer setting.

(Initial)

NOTE:

• When “Small” has been selected for the surround speakers, “Large” cannot be selected for the surround back speakers.

Use the (left) and (right) buttons to select your surround speaker type.

3 SURR. SMALL

LARGE

SMALL

NONE

(left) button (right) button

Press the ENTER or (down) button to switch to the surround back speaker setting.

(Initial)

NOTE:

• When “Small” has been selected for the front speakers, “Large” cannot be selected for the surround speakers.

ENGLISH

Page is loading ...

Denon DHT-485XP User manual

Brand: Denon

Model: DHT-485XP

Category: AV receivers

Type: User manual

This manual is also suitable for

Download PDF

report

Denon DHT-485XP User manual

This manual is also suitable for

Denon DHT-485XP User manual

Related papers

Other documents