ProForm 475 Audio User manual

Category
Treadmills
Type
User manual

This manual is also suitable for

USER'S MANUAL
M
odel No. PETL30706.0
Serial No.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts,
please call:
or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
08457 089 009
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLESHOOTING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
2
PROFORM is a registered trademark of ICON IP, Inc.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should be used only by persons
weighing 115 kg (275 lbs.) or less.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women.
Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10.
When connecting the power cord (see page
14), plug the power cord into an earthed cir-
cuit. No other appliance should be on the
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
11. Keep the power cord away from heated sur-
faces.
12. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 25 if the treadmill is
not working properly.)
13. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 16).
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
16. The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
17. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 24.)
You must be able to safely lift 20 kg (45 lbs.) to
raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per
-
sonal trainer describes the change.
WARNING: T
o reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
IMPORTANT PRECAUTIONS
3
21. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
a
nd incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
22. Always remove iFIT.com CDs and videos
from your CD player or VCR when you are not
using them.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never insert any object into any opening.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning
t
he treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
o
ther than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
26. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown at the right have been placed on the treadmill. If a decal is miss-
ing, or if it is not legible, call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
4
5
T
hank you for selecting the new PROFORM
®
4
50 CX
t
readmill. The 450 CX treadmill combines advanced
technology with innovative design to help you get the
most from your exercise in the convenience of your
home. And when you’re not exercising, the 450 CX
treadmill can be folded up, requiring less than half the
floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
i
ng this manual, please see the front cover of this man-
u
al. To help us assist you, please note the product
model number and serial number before contacting us.
The model number of the treadmill is PETL30706.0
The serial number can be found on a decal attached to
the treadmill (see the front cover of this manual for the
location).
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
BEFORE YOU BEGIN
Handrail
Storage Latch
Key/Clip
Circuit Breaker
On/Off Switch
Walking Belt
Cushioned Walking Platform
for maximum exercise comfort
Foot Rail
RIGHT SIDE
Rear Roller
Adjustment Bolts
Console
Accessory Tray
Handgrip Pulse Sensor
BACK
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated
with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the
walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there
is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own phillips screwdriver , rubber
mallet , adjustable spanner , and wire cutters .
For help identifying the assembly hardware, see the drawings below.
The number in parentheses below each
drawing is the key number of the part, from the PART LIST in the center of this manual. The number following the
parentheses is the quantity needed for assembly.
Note: If a part is not in the parts bag, check to see if it has
been pre-assembled. To avoid damaging plastic parts, do not use power tools for assembly.
Nut (47)–2
Frame Bolt (32)–2
3/4” Screw (2)–12
Upright Bolt (40)–4
Upright Washer
(33)–2
Handrail Bolt (20)–4
Silver Ground
Screw (27)–2
Console Bolt
(22)–2
1/4” Star Washer
(21)–2
Handrail Star
Washer (19)–4
Upright Star
Washer (39)–4
L
Endcap Screw
(95)–2
6
1. Make sure that the power cord is unplugged.
I
dentify the Right Upright (36), which has a
square hole in the location shown. Slide the
R
ight Base Leg Cover (102) onto the Right
Upright.
Orient the Right Upright (36) and the Base (48)
as shown. Attach the Right Upright to the Base
with two Upright Bolts (40) and two Upright Star
Washers (39);
do not tighten the Upright Bolts
yet.
48
40
39
36
1
02
1
2. Orient the Left Upright (31) as shown, and slide
the Left Base Leg Cover (101) onto the Left
Upright.
Attach the Left Upright (31) to the Base (48) with
two Upright Bolts (40) and two Upright Star
Washers (39); do not tighten the Upright Bolts
yet.
Raise the Uprights (31, 36).
48
31
101
39
39
36
2
Square
Hole
40
3.
Place an elastic band around the Right Base Leg
Cover (102) and the bracket on the Right Upright
(36) as shown. Place another elastic band
around the Left Base Leg Cover (not shown) and
the bracket on the Left Upright (not shown).
Position the Base (48) near the front of the tread-
mill as shown.
Locate the wire in the Right Upright (36). See the
inset drawing. Tie the wire
securely to the con-
nector on the Upright Wire (28). Then, insert the
connector into the square hole in the Right
Upright.
48
36
Bracket
Band
102
3
Wire
28
36
7
28
Wire
8
4. See the left inset drawing. Identify the two Frame
Spacers (34). Open the included packet of
g
rease, and apply grease to both sides of both
Frame Spacers. Then, identify the outer side of
e
ach Frame Spacer.
Hold a Frame Spacer (34) between the Right
Upright (36) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Right Upright. Attach the Right Upright to the
Lift Frame with a Frame Bolt (32), an Upright
Washer (33), and a Nut (47);
do not tighten the
Nut yet.
4
31
36
32
32
34
34
33
47
4
7
59
33
59
Outer
Side
Inner
Side
34
36
5. See the left inset drawing. Identify the outer side
of the remaining Frame Spacer (34).
Hold the Frame Spacer (34) between the Left
Upright (31) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Left Upright. Attach the Left Upright to the Lift
Frame with a Frame Bolt (32), an Upright
Washer (33), and a Nut (47); do not tighten the
Nut yet.
5
31
32
32
34
34
33
47
47
59
33
59
Outer
Side
Inner
Side
34
31
9
7. Identify the Right Handrail Endcap (91), which
does not have a cutout in the bottom, and slide it
onto the lower end of the Right Handrail (11).
Make sure that the screw hole in the Right
Handrail Endcap is at the bottom. Next, hold the
Right Handrail near the Right Upright (36), and
insert the Upright Wire (28) into the hole in the
bottom of the Right Handrail and out of the indi-
cated hole in the top. Then, remove the tie from
the Upright Wire.
Set the Right Handrail (11) on the Right Upright
(36) while sliding the lower end of the Right
Handrail onto the bracket on the Right Upright.
Hand tighten two Handrail Bolts (20) with two
Handrail Star Washers (19) into the Right
Handrail and the Right Upright. Next, slide the
Right Handrail Endcap (91) against the Right
Upright, and tighten an Endcap Screw (95) into
the Right Handrail Endcap. Then, tighten the two
Handrail Bolts. Make sure that the Upright
Wire (28) is not pinched.
Attach the Left Handrail (18) and the Left
Handrail Endcap (90) to the Left Upright (31) as
described above.
36
31
95
95
91
90
Cutout
28
20
19
18
19
20
11
7
6. Pull the indicated wire until the Upright Wire (28)
is extending from the upper end of the Right
U
pright (36). Then, disconnect and discard the
wire.
Remove the elastic bands from the Left and
Right Base Leg Covers (101, 102) and press
them onto the Base (48) as shown.
36
102
48
101
6
28
Wire
10
9. Pivot the cylinder end of the Gas Spring (112)
down to the position shown. Remove the Spring
Clip (105) from the end of the Gas Spring.
Next, align the cylinder end of the Gas Spring
(112) with the bracket in the center of the Base
(48). Press the end of the Gas Spring onto the
ball on the bracket. Note: It may be necessary to
pivot the Frame (not shown) forward or backward
slightly to align the end of the Gas Spring with
the ball.
See drawing 9a. Insert the Spring Clip (105) into
the two indicated small holes in the Gas Spring
(112). Then, rotate the Spring Clip until it clips
onto the Gas Spring.
With the help of a second person, lower the
Frame (not shown) to the floor.
105
112
112
48
48
Holes
105
9a
Bracket
Bracket
9
8. Have a second person raise and hold the tread-
mill Frame (74).
Identify the Gas Spring (112). Note that the Gas
S
pring has a cylinder end and a rod end. See the
two small inset drawings. Locate the Spring Clip
(105) in the rod end of the Gas Spring. Using
your fingernail or the end of a screwdriver, press
on the end of the Spring Clip to loosen it, rotate
the Spring Clip, and then pull the Spring Clip out
of the Gas Spring. Be careful to avoid losing the
Spring Clip.
Note: Extra Spring Clips are in-
cluded.
Next, hold the rod end of the Gas Spring (112)
near the bracket in the center of the Frame (74).
Press the end of the Gas Spring as far as possi-
ble onto the ball on the bracket.
See drawing 8a. Insert the Spring Clip (105) into
the two indicated small holes in the rod end of
the Gas Spring (112). Then, rotate the Spring
Clip until it clips onto the Gas Spring.
112
105
112
74
74
Bracket
Cylinder
R
od
Bracket
8a
8
1
05
105
Holes
105
1
1
12. Lower the Uprights (31, 36) as shown.
See the inset drawing. Push the Uprights (31,
36) sideways so that the treadmill Frame (74) is
centered between the Uprights.
Firmly tighten the Upright Bolts (40) and the
Frame Bolts (32) on each side of the treadmill.
Do not overtighten the Frame Bolts.
31
31, 36
32
11, 18
74
36
View From Above
Side View
12
40
28
11
10. Attach the ground wire on the Console Base (26)
to the Right Handrail (11) with a Silver Ground
S
crew (27).
C
onnect the wire harness on the Console Base
(26) to the Upright Wire (28) as shown in the
inset drawing. Important: If the connectors are
oriented correctly, they will slide together
easily and snap into place. If the connectors
are not oriented correctly, the console may
be damaged when the power is turned on.
Insert the connectors and excess wire into the
Console Base (26).
27
2
6
Ground
Wire
28
Wire
Harness
10
22
11. Attach the Console Base (26) to the Handrails
(11, 18) with four 3/4" Screws (2); do not
tighten the Screws yet. Next, tighten two
Console Bolts (22) with 1/4" Star Washers (21)
into the Handrails and the Console Base.
Then,
tighten the four Screws.
2
21
2
11
18
11
26
Front View
22
21
12
14. Slide the Left Base Leg Cover (101) onto the
Base (48) as shown. Attach the Left Base Leg
Cover with three 3/4" Screws (2).
Be careful not
to overtighten the Screws.
2
48
2
2
14
15. Tighten a 3/4" Screw (2) into each side of the
Base (48) and each Base Leg Cover (101, 102).
Be careful not to overtighten the Screws.
2
102
101
48
15
101
13. Attach the ground wire on the Upright Wire (28)
to the indicated hole in the Base (48) with a
S
ilver Ground Screw (27).
P
ress the indicated grommet into the Right
Upright (36).
Slide the Right Base Leg Cover (102) onto the
Base (48) as shown. Attach the Right Base Leg
Cover with three 3/4" Screws (2). Be careful not
to pinch the Upright Wire (28). Do not over-
tighten the Screws.
102
48
28
36
2
2
G
rommet
Ground Wire
2
1
3
27
13
17. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt
(see page 26). To protect the floor or carpet, place a mat under the treadmill.
16. Carefully raise the Uprights (31, 36).
R
emove the knob from the pin. Make sure that
the collar and the spring are on the pin as
s
hown. Insert the pin into the Latch Housing
(30), and tighten the knob back onto the pin.
30
31
16
K
nob
Pin
Collar
Spring
14
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply sili-
cone spray or other substances to the walking belt or the walking platform. Such substances will deterio-
rate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric cur-
rent to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug.
Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Press the pins on the power cord into the metal clips
in the adapter as shown. Close the adapter cover over the end of the
power cord and tighten the screw in the adapter.
Important: Make
sure that the adapter cover is secure and the screw has been
tightened before using the power cord.
See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
DANGER: Improper connection of the equipment-earthing conductor can result in an in-
creased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
Socket on treadmill
Metal
Clips
1
2
Pins
Screw
Adapter
Outlet
3
Adapter
Cover
OPERATION AND ADJUSTMENT
15
FEATURES OF THE CONSOLE
The treadmill console offers a selection of features
designed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
The console also features ten preset programs. Each
program controls the speed and incline of the treadmill
as it guides you through an effective workout.
The console also features iFIT.com interactive technol-
ogy. Having iFIT.com technology is like having a per-
sonal trainer in your home. Using a stereo audio cable,
you can connect the treadmill to your portable stereo,
home stereo, computer, or VCR and play special
iFIT.com MP3, CD, and video programs (iFIT.com MP3
programs, CDs, and videocassettes are available sepa-
rately). iFIT.com programs automatically control the
speed and incline of the treadmill as a personal trainer
guides you through every step of your workout; high-
energy music provides added motivation.
To down-
load iFIT.com MP3 programs, go to www.iFIT.com.
To purchase iFIT.com CDs and videocassettes, call
the telephone number on the front cover of the
manual.
With the treadmill connected to your computer, you
can also go to www.iFIT.com and access iFIT.com
programs directly from our Web site. See
www.iFIT.com for more information.
To use the manual mode of the console
, follow the
steps beginning on page 16. To use a preset
program, see page 18. To use an iFIT.com MP3, CD,
or video program
, see page 21. To use an iFIT.com
program directly from our Web site, see page 22.
Note: If there are thin sheets of plastic
on the console, remove the plastic.
Key
Clip
CONSOLE DIAGRAM
16
HOW TO TURN ON THE POWER
P
lug in the power cord (see
page 14). Next, locate the
o
n/off switch on the tread-
mill frame near the power
cord. Make sure that the
on/off switch is in the “on”
position.
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing on page 15),
and slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console; after a
moment, the display will light.
Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
Note: To prevent damage to the walking platform,
always wear clean shoes while using the treadmill.
HOW TO USE THE MANUAL MODE
Insert the key into the console.
See HOW TO TURN ON THE POWER above.
Select the manual mode.
When the key is in-
serted, the manual
mode will be selected.
If a program has been
selected, press the
Program Select button
repeatedly until a track appears in the display.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the buttons
numbered 2 through 16.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 2
K
m/H. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
c
rease and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
Km/H; if a button is held down, the speed setting
will change in increments of 0.5 Km/H.
If one of the eight numbered buttons is pressed,
the walking belt will gradually increase in speed
until it reaches the selected speed setting. Note:
The console can display speed and distance in
either miles or kilometers (see THE INFORMA-
TION MODE/DEMO MODE on page 23). For
simplicity, all instructions in this section refer
to kilometers.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the eight num-
bered buttons.
Note: The first time you use the treadmill, periodi-
cally inspect the alignment of the walking belt, and
center it if necessary (see page 26).
Change the incline of the treadmill as desired.
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
a button is pressed, the incline setting will change
by 0.5%; if a button is held down, the incline set-
ting will change quickly.
4
3
2
1
On
Position
Follow your progress with the display.
When the manual
mode is selected, a
track representing 400
m
eters will appear in
the upper right corner
of the display. As you
walk or run on the treadmill, the indicators around
the track will appear in succession until the entire
track appears. The track will then disappear and
the indicators will again begin to appear in suc-
cession.
The upper left corner
of the display will
show the elapsed time
since you started your
workout.
The lower left corner
of the display will
show the distance that
you have walked or
run during your work-
out and the incline
level of the treadmill.
The lower right corner
of the display will show
the speed of the walk-
ing belt and the ap-
proximate number of
calories that you have
burned during your workout. The lower right cor-
ner of the display will also show your heart rate
when you use the handgrip pulse sensor.
To reset the display, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate if desired.
Before using the handgrip pulse sensor, remove
the sheets of clear plastic from the metal contacts.
In addition, make sure that your hands are clean.
To measure your
heart rate,
stand
o
n the foot rails
and place your
h
ands on the
metal contacts—
avoid moving
your hands.
When your pulse
is detected, the heart symbol in the display will
begin to flash each time your heart beats, one or
two dashes will appear, and then your heart rate
will be shown.
For the most accurate heart rate
reading, continue to hold the contacts for
about 15 seconds.
Turn on the fan if desired.
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a sec-
ond time. To turn off the fan, press the button a
third time. Note: If the fan is left on when the walk-
ing belt is stopped, the fan will automatically turn
off after a few minutes.
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion, or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 23 and turn off the
demo mode.
When you are finished using the treadmill,
switch the
on/off switch to the “off” position
and unplug the power cord.
8
7
6
5
17
Metal Contacts
18
H
OW TO USE A PRESET PROGRAM
I
nsert the key into the console.
S
ee HOW TO TURN ON THE POWER on page
16.
S
elect a preset program.
To select one of the ten
preset programs, press
the Program Select but-
ton repeatedly until one
of the programs num-
bered “P–1” through
“P–10” appears in the display. When a preset pro-
gram is selected, the maximum incline setting of
the program and the maximum speed setting of
the program will flash in the display for a few sec-
onds. The display will also show how long the pro
-
gram will last. A profile of the
speed settings of the
program will scroll across the matrix in the upper
right corner of the display.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several one-minute
periods. One speed setting and one incline setting
are programmed for each period. Note: The same
speed setting and/or incline setting may be pro-
grammed for two or more consecutive periods.
The speed setting for
the first period will be
shown in the flashing
Current Period column
of the matrix in the dis-
play. (The incline set-
tings are not shown in the matrix.) The speed set-
tings for the next four periods will be shown in the
columns to the right.
When only three seconds remain in the first period
of the program, both the Current Period column
and the column to the right will flash and a series
of tones will sound. If the speed and/or incline of
the treadmill is about to change, the speed setting
and/or the incline setting will flash in the display to
alert you.
When the first period is completed,
all speed set-
tings will move one column to the left
. The speed
s
etting for the second period will then be shown in
the flashing Current Period column and the tread-
m
ill will automatically adjust to the speed and in-
cline settings for the second period. Note: If all five
of the indicators in the Current Period column are
lit,
the speed settings may move downward
so that
only the highest indicators appear in the matrix.
The program will continue in this way until the
speed setting for the last period is shown in the
Current Period column and the last period ends.
The walking belt will then slow to a stop.
If the speed or incline setting for the current period
is too high or too low, you can manually override
the setting by pressing the Speed or Incline but-
tons. Every few times a Speed button is pressed,
an additional indicator will appear or disappear in
the Current Period column; if any of the columns
to the right of the Current Period column have the
same number of lit indicators as the Current
Period column, an additional indicator may appear
or disappear in those columns as well.
Important:
When the current period of the program ends,
the treadmill will automatically adjust to the
speed and incline settings for the next period.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 2 Km/H. When the next period of
the program begins, the treadmill will automatically
adjust to the speed and incline settings for the
next period. To end the program, press the Stop
button, remove the key, and then reinsert the key.
Follow your progress with the display.
See step 5 on page 17.
Measure your heart rate if desired.
See step 6 on page 17.
Turn on the fan if desired.
See step 7 on page 17.
When the program is completed, remove the
key from the console.
See step 8 on page 17.
7
6
5
4
3
2
1
Current Period
19
T
o use iFIT.com MP3 or CD programs
,
the treadmill
m
ust be connected to your MP3 player, CD player,
portable stereo, home stereo, or computer. See pages
19 and 20 for connecting instructions.
To use
iFIT.com programs directly from our Web site, the
treadmill must be connected to your computer. See
page 20 for connecting instructions. To use iFIT.com
video programs, the treadmill must be connected to
your VCR. See page 21 for connecting instructions.
HOW TO CONNECT YOUR MP3 PLAYER OR CD
PLAYER
A. Plug one end of the included 3.5mm to 3.5mm
stereo audio cable into the input jack on the con-
sole. Plug the other end of the cable into a jack on
your MP3 player or CD player. Plug your head-
phones into the headphone jack on the console.
HOW TO CONNECT YOUR PORTABLE STEREO
N
ote: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3
.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
A. Plug one end of a long 3.5mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the AUDIO OUT jack on your stereo.
B. See the drawing above. Plug one end of a long
3.5mm to 3.5mm stereo audio cable (available at
electronics stores) into the input jack on the con-
sole. Plug the other end of the cable into the LINE
OUT jack on your stereo. Note: While the cable is
plugged into the LINE OUT jack, do not plug your
headphones into the headphone jack on the con-
sole.
C. Plug one end of a long 3.5mm to 3.5mm stereo
audio cable (available at electronics stores) into the
input jack on the console. Plug the other end of the
cable into the PHONES jack on your stereo. Plug
your headphones into the headphone jack on the
console.
LINE OUT
PHONES
LINE OUT
PHONES
Audio
Cable
Headphones
A
AUDIO OUT
RIGHT
LEFT
LINE OUT
Audio Cable
A/B
PHONES
Audio
Cable
C
Headphones
H
OW TO CONNECT THE TREADMILL TO USE
I
FIT.COM PROGRAMS
20
HOW TO CONNECT YOUR HOME STEREO
N
ote: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
b
eing used, see instruction B.
A. Plug one end of a long 3.5mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into the LINE OUT jack on your stereo. Note: While
the cable is plugged into the LINE OUT jack, do not
plug your headphones into the headphone jack on
the console.
B. Plug one end of a long 3.5mm to RCA stereo audio
cable (available at electronics stores) into the input
jack on the console. Plug the other end of the cable
into an RCA Y-adaptor (available at electronics
stores). Next, remove the wire that is currently
plugged into the LINE OUT jack on your stereo and
plug the wire into the unused side of the Y-adaptor.
Plug the Y-adaptor into the LINE OUT jack on your
stereo. Note: While the Y-adaptor is plugged into the
LINE OUT jack, do not plug your headphones into
the headphone jack on the console.
HOW TO CONNECT YOUR COMPUTER
A
. Plug one end of a long 3.5mm to 3.5mm stereo
audio cable (available at electronics stores) into the
i
nput jack on the console. Plug the other end of the
cable into the LINE OUT jack on your computer.
Note: While the cable is plugged into the LINE OUT
jack, do not plug your headphones into the head-
phone jack on the console.
L
INE OUT
Audio Cable
A
CD
VCR
Amp
LINE OUT
LINE OUT
Audio Cable
A
CD
VCR
Amp
L
INE OUT
Audio
Cable
RCA
Y-adaptor
Wire removed from
LINE OUT jack
B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31

ProForm 475 Audio User manual

Category
Treadmills
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI