Porter-Cable 97466 User manual

Brand: Porter-Cable

Model: 97466

Category: Power tools

Type: User manual

DEFINITIONS - SAFETY GUIDELINES

indicates an imminently hazardous situation which, if not avoid-

ed, will result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

indicates a potentially haz ard ous situation which, if not avoided,

may result in minor or mod er ate injury.

used without the safety alert symbol indicates potentially hazard-

ous situation which, if not avoided, may result in property damage.

To reduce the risk of injury, read the instruction manual.

GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warningS and inStructionS

for future reference

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of flam-

mable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets

will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication. A moment of inattention while operating power tools may result in serious per-

sonal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off position before connect-

ing to power source and/or battery pack, picking up or carrying the tool. Carrying power

tools with your finger on the switch or energising power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving

parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such pre-

ventive safety measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these instructions

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

5) SERVICE

a) Have your power tool serviced by a qualified repair person using only identical replace-

ment parts. This will ensure that the safety of the power tool is maintained.

ADDITIONAL SPECIFIC SAFETY RULES

SAFETY WARNINGS COMMON FOR GRINDING, SANDING, WIRE BRUSHING, POLISHING OR

ABRASIVE CUTTING-OFF OPERATIONS:

a) This power tool is intended to function as sander or polisher. Read all safety warnings,

instructions, illustrations and specifications provided with this power tool. Failure to follow all

instructions listed below may result in electric shock, fire and/or serious injury.

b) Operations such as grinding, wire brushing or cutting-off are not recommended to be

performed with this power tool. Operations for which the power tool was not designed may

create a hazard and cause personal injury.

c) Do not use accessories which are not specifically designed and recommended by the

tool manufacturer. Just because the accessory can be attached to your power tool, it does not

assure safe operation.

d) The rated speed of the accessory must be at least equal to the maximum speed marked on

the power tool. Accessories running faster than their RATED SPEED can break and fly apart.

e) The outside diameter and the thickness of your accessory must be within the capacity

rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or con-

trolled.

f) The arbor size of wheels, flanges, backing pads or any other accessory must properly fit

the spindle of the power tool. Accessories with arbor holes that do not match the mounting

hardware of the power tool will run out of balance, vibrate excessively and may cause loss of

control.

g) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing an accessory, position yourself and bystanders

away from the plane of the rotating accessory and run the power tool at maximum no-load speed

for one minute. Damaged accessories will normally break apart during this test time.

h) Wear personal protective equipment. Depending on application, use face shield, safety gog-

gles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop

apron capable of stopping small abrasive or workpiece fragments. The eye protection must be

capable of stopping flying debris generated by various operations. The dust mask or respirator

must be capable of filtrating particles generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work area. Anyone entering the work area must

wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly

away and cause injury beyond immediate area of operation.

j) Hold power tool by insulated gripping surfaces only, when performing an operation where

the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contact-

ing a "live" wire may make exposed metal parts of the power tool "live" and shock the operator.

k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled into the spinning accessory.

l) Never lay the power tool down until the accessory has come to a complete stop. The spin-

ning accessory may grab the surface and pull the power tool out of your control.

m) Do not run the power tool while carrying it at your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the accessory into your body.

n) Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the hous-

ing and excessive accumulation of powdered metal may cause electrical hazards.

o) Do not operate the power tool near flammable materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may

result in electrocution or shock.

KICKBACK AND RELATED WARNINGS

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other

accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes

the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the

point of the binding.

For example, if a backing pad is snagged or pinched by the workpiece, the edge of the pad that is

entering into the pinch point can dig into the surface of the material causing the wheel to climb out or

kick out. The wheel may either jump toward or away from the operator, depending on direction of the

wheel’s movement at the point of pinching.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and

can be avoided by taking proper precautions as given below.

a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or

torque reaction during start-up. The operator can control torque reactions or kickback forces, if

proper precautions are taken.

b) Never place your hand near the rotating accessory. Accessory may kickback over your hand.

c) Do not position your body in the area where power tool will move if kickback occurs. Kickback

will propel the tool in direction opposite to the wheel’s movement at the point of snagging.

d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory

and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create

frequent kickback and loss of control.

SAFETY WARNINGS SPECIFIC FOR SANDING OPERATIONS:

a) Do not use excessively oversized sanding disc paper. Follow manufacturer’s recommenda-

tions when selecting sanding paper. Larger sanding paper extending beyond the sanding pad

presents a laceration hazard and may cause snagging, tearing of the disc or kickback.

SAFETY WARNINGS SPECIFIC FOR POLISHING OPERATIONS:

a) Do not allow any loose portion of the polishing bonnet or its attachment strings to spin

freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment

strings can entangle your fingers or snag on the workpiece.

EXTENSION CORD

An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety.

The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a drop in line voltage resulting in

loss of power and overheating. When using more than one extension to make up the total length, be

sure each individual extension contains at least the minimum wire size. The following table shows

the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the

next heavier gauge. The smaller the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V

25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V

50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

Always use eye protection. All users and bystanders must wear eye protection that

conforms to ANSI Z87.1.

Always wear proper personal hearing protection that conforms to ANSI S12.6

(S3.19) during use. Under some conditions and duration of use, noise from this product may

contribute to hearing loss.

ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSIZ87.1eyeprotection(CAN/CSAZ94.3),

• ANSIS12.6(S3.19)hearingprotection,

• NIOSH/OSHA/MSHArespiratoryprotection.

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some

examples of these chemicals are:

• leadfromlead-basedpaints,

• crystallinesilicafrombricksandcementandothermasonryproducts,and

• arsenicandchromiumfromchemically-treatedlumber(CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area, and work with approved

safety equipment, such as those dust masks that are specially designed to filter out microscopic

particles.

• Avoid prolongedcontactwith dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption

of harmful chemicals.

Use of this tool can generate and/or disburse dust, which may cause serious and perma-

nentrespiratoryorotherinjury.AlwaysuseNIOSH/OSHAapprovedrespiratoryprotectionappropriatefor

the dust exposure. Direct particles away from face and body.

SYMBOLS

The label on your tool may include the following symbols.

The symbols and their definitions are as

follows:

V ....................... volts A ................. amperes

Hz .................... hertz W ................ watts

min ................... minutes

.............. alternating current

................ direct current .............. alternating or direct current

..................... Class I Construction

o ............... no load speed

......................... (grounded)

............... earthing terminal

.................... Class II Construction ............... safety alert symbol

......................... (double insulated) BPM ........... beats per minute

…/min .............. per minute RPM ........... revolutions per minute

OPM ................ orbits per minute

ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

1. Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the con-

taminated dust. The greatest danger of lead poisoning is to children and pregnant women.

2. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we

recommend the following precautions when sanding any paint:

PERSONAL SAFETY

1. No children or pregnant women should enter the work area where the paint sanding is being

done until all clean up is completed.

2. A dust mask or respirator should be worn by all persons entering the work area. The filter should

be replaced daily or whenever the wearer has difficulty breathing. See your local hardware store

fortheproperNIOSHapproveddustmask.

3. NO EATING, DRINKING or SMOKING should be done in the work area to prevent ingesting

contaminated paint particles. Workers should wash and clean up BEFORE eating, drinking or

smoking. Articles of food, drink, or smoking should not be left in the work area where dust would

settle on them.

Instruction manual

Manuel d'instructions

Manual de'instrucciones

7345

7346

7346SP

7424XP

97455

97466

www.deltaportercable.com

INSTRUCTIVO DE OPERACIÓN, CENTROS

DE SERVICIO Y PÓLIZA DE GARANTÍA.

LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

VARIABLE SPEED

RANDOM ORBIT

SANDER/POLISHER

Polisseuse á orbite aléatoire

á vitesse variable

Pulidora de órbita excéntrica

de velocidad variable

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a manner as to minimize the amount of dust generated.

2. Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mil thickness.

3. Sanding should be done in a manner to reduce tracking of paint dust outside the work area.

CLEANING AND DISPOSAL

1. All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration

of the sanding project. Vacuum filter bags should be changed frequently.

2. Plastic drop cloths should be gathered up and disposed of along with any dust chips or other

removal debris. They should be placed in sealed refuse receptacles and disposed of through

regular trash pick-up procedures. During clean up, children and pregnant women should be kept

away from the immediate work area.

3. All toys, washable furniture and utensils used by children should be washed thoroughly before

being used again.

Save theSe inStructionS

MOTOR

Be sure your power supply agrees with nameplate marking. 120 Volts AC means your tool will operate on

alternating current. As little as 10% lower voltage can cause loss of power and can result in overheating.

All Porter Cable tools are factory-tested; if this tool does not operate, check the power supply.

Accessories must be rated for at least the speed recommended on the tool warning label.

Accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be

above tool speed as shown on tool nameplate.

To reduce the risk of injury, turn unit off and disconnect it from power source

before installing and removing accessories, before adjusting or when making repairs. An

accidental start-up can cause injury.

OPERATION

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-

up can cause injury.

AUXILIARY HANDLE

An auxiliary handle (A) Fig. 1 is furnished with the tool. You can install the auxiliary handle on either

side of the front housing to facilitate either right-handed or left-handed operation.

Use this handle at all times to maintain complete control of the tool.

TO START AND STOP TOOL

Make certain that the switch is in the “OFF” position, and the power source is the same as that

specified on the tool’s nameplate.

1. Connect the tool to the power source.

2. Slide the switch button (B) Fig. 1 forward to start the motor. Slide the switch button to the rear

to stop the motor.

VARIABLE SPEED

Adjust the speed by turning the thumbwheel (C) Fig. 2. Thumb-wheel position #1 provides the slow-

est operating speed (2500 OPM) and position #6, the fastest (6800 OPM). You can change the speed

while the motor is running or while it is stopped.

USING THE POLISHER (FIG. 3)

If your workpiece is so light that it can be moved by the rotating pad, anchor it securely

to prevent possible bodily injury.

1. Read and follow the directions supplied with the product (polishes, waxes, cleaners, etc.).

2. Apply a small amount of the product directly to the polishing pad.

3. Grasp the polisher firmly with both hands - one hand on auxiliary handle and one hand on motor

housing.

4. Position the polisher with the polishing pad against the work surface and start the polisher.

NEVER run or stop the tool when it is not in contact with the work surface.

5. Move the polisher back and forth in a sweeping motion, over-lapping each previous pass.

6. DO NOT apply additional pressure. Allow the polisher to work under its own weight.

7. Do not mix products (wax, polish, cleaner, etc.) on the same pad. Label each pad to prevent

confusion.

8. The polishing pad is designed for product application only. Remove product residue with a soft

cotton cloth.

INSTALLING/REMOVING ABRASIVE DISC (FIG. 4)

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-

up can cause injury.

1. Place the tool on the work-bench with the pad up (Fig. 4).

2. Clean dust from the pad face.

3. Position the disc on the sander pad and press the disc firmly on the pad.

4. Position the tool with the abrasive contacting scrap material. Start the tool and operate it

momentarily with firm pressure to seat the disc to the pad.

Failure to properly seat the disc to the pad may result in the disc being thrown from

the pad, causing personal injury.

6. Remove the disc by peeling it away from pad.

NOTE FOR PSA PADS:Donotstorethetoolwiththeabrasivediscinstalled.Heatgeneratedbythe

sanding operation increases the adhesive bond between the disc and the pad. If the disc is left on

the pad for an extended period of time after use, it will be difficult to remove.

CHANGING THE BACK-UP PAD

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-

up can cause injury.

1. Engage the flats of the spindle (D) Fig. 5 with the supplied spindle wrench (E).

NOTES:

A. If necessary, rotate the pad by hand to expose the spindle flats.

B. The pad is removed in Fig. 5 for clarity.

C. A spacer is supplied with the 7346SP and 7424XP to allow the backup pad to clear the eccen-

tric plate screws (F) Fig. 5. Mount the spacer on the shaft before attaching the backup pad.

2. While holding the spindle with the wrench, use your other hand to rotate the pad counterclock-

wise to remove.

3. To install the pad, reverse the above procedure.

USING THE SANDER (FIG. 6)

Secure the workpiece to prevent it from moving. Friction between the sanding disc and the work-

piece can spin the workpiece away from sander and may cause bodily injury.

Always use eye protection. To reduce the risk of injury, all users and bystanders must

wear eye protection that conforms to ANSI Z87.1.

Use of this tool can generate and/or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face and body.

INSTALLING ACCESSORY DUST COLLECTION ADAPTER AND HOSE

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-

up can cause injury.

1. Remove sander pad (G) Fig. 4.

2. LoosenPhillipsheadscrew(H)Fig.7ondustcollectionadapter(I)andslidetheadapteruponto

the vacuum housing (J) as shown in Fig. 7.

3. Orient dust hole (K) Fig. 8 as shown and tighten Phillips head screw.

4. Attach dust hose adapter (L) and dust hose (M) as shown.

TROUBLESHOOTING

For assistance with your tool, visit our website at www.deltaportercable.com for a list of service centers,

or call the PORTER-CABLE Customer Care Center at (888) 848-5175.

MAINTENANCE

To reduce the risk of injury, turn unit off and disconnect it from power source before

installing and removing accessories, before adjusting or when making repairs. An accidental start-

up can cause injury.

ALWAYS USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. Also use

face or dust mask if cutting operation is dusty. ALWAYS wear certified safety equipment:

 • ANSIZ87.1eyeprotection(CAN/CSAZ94.3)

 • ANSIS12.6(S3.19)hearingprotection

 • NIOSH/OSHA/MSHArespiratoryprotection.

REPAIRS

For assistance with your tool, visit our website at www.deltaportercable.com for a list of service centers,

or call the PORTER-CABLE Customer Care Center at (888) 848-5175.

CLEANING

Periodically blowing dust and chips out of the motor housing using clean, dry compressed

air is a suggested maintenance procedure. To reduce the risk of serious personal injury, ALWAYS wear

ANSI Z87.1 safety glasses while using compressed air.

When cleaning, use only mild soap and a damp cloth on plastic parts. Many household

cleaners contain chemicals which could seriously damage plastic. Also, do not use gasoline, turpentine,

lacquer, paint thinner, dry cleaning fluids or similar products which may seriously damage plastic parts.

NEVER let any liquid get inside the tool; NEVER immerse any part of the tool into a liquid.

FAILURE TO START

Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in

the outlet. Also, check for blown fuses or open circuit breakers in the line.

LUBRICATION

This tool has been lubricated with a sufficient amount of high grade lubricant for the life of the unit under

normal operating conditions. No further lubrication is necessary.

BRUSH INSPECTION

For your continued safety and electrical protection, brush inspection and replacement on this tool

should ONLY be performed by a PORTER-CABLE FACTORY SERVICE CENTER OR PORTER-CABLE

AUTHORIZEDWARRANTYSERVICECENTER.

At approximately 100 hours of use, take or send your tool to your nearest PORTER-CABLE Factory

Service center or PORTER-CABLE Authorized Warranty Service Center to be thoroughly cleaned and

inspected.Havewornpartsreplacedandlubricatedwithfreshlubricant.Havenewbrushesinstalled,and

test the tool for performance.

Any loss of power before the above maintenance check may indicate the need for immediate servicing of

yourtool.DONOTCONTINUETOOPERATETOOLUNDERTHISCONDITION.Ifproperoperatingvoltage

is present, return your tool to the service station for immediate service.

SERVICE

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at

www.deltaportercableservicenet.com. You can also order parts from your nearest PORTER-CABLE

Factory Service Center or PORTER-CABLE Authorized Warranty Service Center. Or, you can call our

Customer Care Center at (888) 848-5175.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about

PORTER-CABLE, its factory service centers or authorized warranty service centers, visit our website at

www.deltaportercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our

service centers are fully guaranteed against defective material and workmanship. We cannot guarantee

repairs made or attempted by others.

YoucanalsowritetousforinformationatPORTER-CABLE,4825Highway45North,Jackson,Tennessee

38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of

your tool (model number, type, serial number, etc.).

ACCESSORIES

Since accessories, other than those offered by PORTER-CABLE, have not been tested with

this product, use of such accessories with this tool could be hazardous. To reduce the risk of injury, only

PORTER-CABLE recommended accessories should be used with this product.

A complete line of accessories is available from your PORTER-CABLE Factory Service Center or a

PORTER-CABLE Authorized Warranty Service Center. Please visit our Web Site www.deltaportercable.

com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair, without charge, any defects due to faulty materials or workmanship for three

years from the date of purchase. This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit www.deltaportercable.

com or call (888) 848-5175. This warranty does not apply to accessories or damage caused where repairs

have been made or attempted by others. This warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our:

1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn parts caused by nor-

mal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the performance of your

PORTER-CABLE Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date

of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in

Latin America, see country specific warranty information contained in the packaging, call the local com-

pany or see website for warranty information.

To register your tool for warranty service visit our website at www.deltaportercable.com.

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free replacement.

TO REDUCE THE

RISK OF INJURY,

USER MUST READ INSTRUCTION MANUAL.

ALWAYS USE PROPER EYE AND RESPIRATORY

PROTECTION.

U. S. PATENT 5,061,090 D326042

PORTER-CABLE, JACKSON, TN 38305 U.S.A.

Model 7XXX

6" (152 mm) Variable Speed

Random Orbit Sander

PARA EL MANEJO

SEGURO LEA EL

MANUAL DE INSTRUCCIONES. SIEMPRE SE DEBERÁ

LLEVAR LA PROTECCIÓN APROPIADA PARA LA VISTA Y

PARA LAS VÍAS RESPIRATORIAS.

À TITRE PRÉVENTIF,

LIRE LE GUIDE. IL

FAUT TOUJOURS PORTER DE L’ÉQUIPEMENT DE

PROTECTION OCULAIRE ET RESPIRATOIRE APPROPRIÉ.

PARA EL MANEJO

SEGURO LEA EL

MANUAL DE INSTRUCCIONES. SIEMPRE SE DEBERÁ

LLEVAR LA PROTECCIÓN APROPIADA PARA LA VISTA Y

PARA LAS VÍAS RESPIRATORIAS.

À TITRE PRÉVENTIF,

LIRE LE GUIDE. IL

FAUT TOUJOURS PORTER DE L’ÉQUIPEMENT DE

PROTECTION OCULAIRE ET RESPIRATOIRE APPROPRIÉ.

TO REDUCE THE

RISK OF INJURY,

USER MUST READ INSTRUCTION MANUAL.

ALWAYS USE PROPER EYE AND RESPIRATORY

PROTECTION.

U. S. PATENT 5,061,090 D326042

PORTER-CABLE, JACKSON, TN 38305 U.S.A.

Model 7XXX

6" (152 mm) Variable Speed

Random Orbit Sander

PARA EL MANEJO

SEGURO LEA EL

MANUAL DE INSTRUCCIONES. SIEMPRE SE DEBERÁ

LLEVAR LA PROTECCIÓN APROPIADA PARA LA VISTA Y

PARA LAS VÍAS RESPIRATORIAS.

À TITRE PRÉVENTIF,

LIRE LE GUIDE. IL

FAUT TOUJOURS PORTER DE L’ÉQUIPEMENT DE

PROTECTION OCULAIRE ET RESPIRATOIRE APPROPRIÉ.

PARA EL MANEJO

SEGURO LEA EL

MANUAL DE INSTRUCCIONES. SIEMPRE SE DEBERÁ

LLEVAR LA PROTECCIÓN APROPIADA PARA LA VISTA Y

PARA LAS VÍAS RESPIRATORIAS.

À TITRE PRÉVENTIF,

LIRE LE GUIDE. IL

FAUT TOUJOURS PORTER DE L’ÉQUIPEMENT DE

PROTECTION OCULAIRE ET RESPIRATOIRE APPROPRIÉ.

FIG. 1

FIG. 2 FIG. 3

FIG. 4

FIG. 5 FIG. 6

FIG. 7

FIG. 8

Page is loading ...

Porter-Cable 97466 User manual

Brand: Porter-Cable

Model: 97466

Category: Power tools

Type: User manual

Download PDF

report

in other languages

français: Porter-Cable 97466 Manuel utilisateur
español: Porter-Cable 97466 Manual de usuario

Porter-Cable 97466 User manual

Porter-Cable 97466 User manual

in other languages

Related papers

Other documents