Zephyr Genova ZGE-E30AS290 Installation guide

Use, Care, and Installation Guide

www.zephyronline.com

Model number:

Serial Number:

APR14.0401 © Zephyr Corporation

Genova

ZGE-E30AS

ZGE-E36AS

ZGE-E30AS290

ZGE-E36AS290

www.zephyronline.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet

....................................... 5

Mounting Height & Clearance

................................ 6

Ducting Options

........................................................... 7

+RRG6SHFL¿FDWLRQV

................................................... 8

Preparing the Cabinet

............................................... 9

Installing the Hood

...................................................... 10 - 12

Ductless Recirculation

.............................................. 13

FEATURES & CONTROLS

Touch Controls

.............................................................. 14-15

Remote Control (Optional)

....................................... 16

MAINTENANCE

Hood and Filter Cleaning

......................................... 17

Lights

................................................................................ 18

Wiring Diagram

............................................................ 19

TROUBLESHOOTING

................................................................ 20

LIST OF PARTS AND ACCESSORIES

.............................. 21

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG

F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516

,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

 7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG

 7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG

 <RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV

,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ

E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV

attics, crawl spaces or garages. Hood not intended for installation over an outdoor grill.

OPERATION

$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH

ground path is adequate.

Do not ground to a gas pipe.

&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase

and install appropriate connector if necessary.

ZGE-E30AS, ZGE-E36AS - 370 Watts, 3.5 Amps

ZGE-E30AS290, ZGE-E36AS290 - 167 Watts, 3.5 Amps

List of Materials

4

www.zephyronline.com

(3) Wire Nuts

(1) Suction Cup

(1) 6” round damper (pre-installed)

(1) hood body with sliding glass

(2) upper installation brackets

(2) lower installation brackets

(1) filler panel (pre-installed)

(1) hardware package

MODELS: ZGE-E30AS, ZGE-E30AS290, ZGE-E36AS, ZGE-E36AS290

PARTS SUPPLIED

HARDWARE PACKAGE CONTENTS

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

- Cable connector (if required by local codes)

- Recirculating kit accessory - ZRC-00GE

- Remote control accessory - 14000005

(2) halogen lights, GU-10 50W

(1) decorative mesh filter

(2) M4 x 8 (2) M4 x 1”

(4) 3/16 x 3/8”

(4) 3/16 x 1”

5

Duct pieces

To t a l

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

8” Round,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6” Round,

90

0

elbow

15 Ft. x ( ) =

Ft.

6” Round,

45

0

elbow

9 Ft. x ( ) =

Ft.

7” Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

To t a l

Equivalent number

length x used =

6”- 8” Round

wall cap

with damper

30 Ft. x ( ) =

Ft.

Round

wall cap

with damper

30 Ft. x ( ) =

Ft.

7” or 8”

Round,

90

0

elbow

15 Ft. x ( ) =

Ft.

7” or 8”

Round,

45

0

elbow

9 Ft. x ( ) =

Ft.

6”- 8” Round,

roof cap

30 Ft. x ( ) =

Ft.

7” or 8”

Round,

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length of a 3 1/ 4” x 10” rectangular 6” or 7”

diameter round duct should not exceed 100 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

Installation – Ducting Calculation Sheet

Installation – Installing the Hood

6

www.zephyronline.com

DUCTING

A minimum of 6” round ducting must be used to

PDLQWDLQPD[LPXPDLUÀRZHI¿FLHQF\

Always use rigid type metal ducts only. Flexible

GXFWVFRXOGUHVWULFWDLUÀRZE\XSWR

Use calculation worksheet to compute total duct

work.

ALWAYS, when possible, reduce the number of

transitions and turns. If a long duct run is required,

increase duct size from 6” to 7” or 8”.

If turns or transitions are required: Install as far

away from opening and as far apart, between 2,

as possible.

36”

24” min.

32” max.

Mounting height from top of cooking surface to

bottom of hood should be no less than 24” and no

more than 32”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV

mounted too high will be hard to reach and will

ORVHSHUIRUPDQFHDQGHI¿FLHQF\

If available, also refer to range manufacturer’s

height clearance requirements and recommended

hood mounting height above range. Always check

your local codes for any differences.

DAMAGE-SHIPMENT / INSTALLATION:

 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH

installation.

 ,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKH

unit to the store in which it was bought for

repair or replacement.

 ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLU

or replacement is the responsibility of the

customer.

 ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU

than the customer), repair of replacement must

be made by arrangement between customer

and installer.

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid Metal ductwork only.

)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZFHUWL¿HG6LOYHU7DSHRU'XFW7DSH

Ducting Options Example

Installation – Ducting Options

soffit or crawl space

roof pitch w/

flashing & cap

ductless

recirculating

w/ gravity damper

side wall cap

ductless

recirculating

soffit

8

www.zephyronline.com

Installation – +RRG6SHFL¿FDWLRQV

front of hood

side of hood

top of hood

500mm

19

11

16

"

76mm

3"

280mm

11"

912mm

35

7

8

"

760mm

29

15

16

"

242mm

9

1

2

"

153mm

6

"

197mm

7

3

4

"

180mm

7

1

16

"

16mm

5

8

"

445mm

17

1

2

"

473mm

to

18

5

8

"

286mm

11

1

4

"

6mm

1

to

4

"

1

3

8

"

35mm

153mm

6

"

41mm

5

8

"

1

28mm

1

8

"

1

junction box

blower outlet

9

7

3/4

”

7”

9-

7/8”

19-7/8”

C/L

1

-

9/16”

Installation – Preparing the Cabinet

Fig.1

front edge

glass handle

Fig.2

1. Determine and mark center line on wall and cabinet bottom with a pencil.

2. If the cabinet bottom is recessed, wood blocking must be installed to ensure proper

DOLJQPHQWRIWKHKRRGZLWKWKHFDELQHWERWWRP:RRGEORFNLQJVKRXOGEHÀXVK 

within cabinet bottom.

3. Follow the dimensions in Fig.1 and cut-out the bottom of your cabinet to create an opening

IRUWKHKRRGWR¿WWKURXJK,I\RXKDYHDIUDPHOHVVFDELQHWEHJLQWKH´PHDVXUHPHQW

(referenced in Fig.1) from front of the cabinet door. This way the front edge of the hood will

EHÀXVKZLWKWKHFDELQHWGRRUVZKHQFORVHGVHH)LJ

10

www.zephyronline.com

Installation – Installing the Hood

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be

properly grounded. Turn off electrical power at service entrance before wiring.

!

1) Prepare electrical wiring and ducting in cabinet. Location of junction box and blower outlet can be found on page 8.

2) Unscrew the (10) screws from front panel and place

the panel aside, Fig.3. You will now have access to the

interrior of the range hood.

Fig.3 Fig.4

3) Open cabinet doors. Lift range hood and slide it through

the opening located in the bottom of the cabinet, Fig.4.

Make sure opening matches the dimensions on page 9,

Fig.1.

4) There are spring clips located on the left and right sides

of the hood body which will temporarily hold the hood in

place, Fig.5.

Fig.5 Fig.6

5) Secure upper brackets to left and right sides of hood

body by using (2) 3/16 x 3/8” screws for each bracket.

Fig.6. Make sure the (2) captive nut screw holes on

the bracket are facing downward. Note: Due to limited

workspace in 30” cabinets you will need to use a right

angle or 2” long Philips head screwdriver.

1

2

Installation – Installing the Hood

11

6) Place lower installation brackets under upper installation

brackets located on left and right sides of hood body,

Fig.7. Note: The wider portion of the lower installation

bracket should be at the bottom.

Fig.7 Fig.8

7) From inside the hood, secure (1) M4x8 screw into

each lower installation bracket. The position of this

screw is adjustable to accomodate various cabinet

bottom thicknesses, Fig.8. Do not fully tighten screw yet.

8) Install (2) 3/16x1” screws into the captive nuts of each

upper installation bracket. Tighten screws to adjust the

height of range hood until there is no gap between the

cabinet bottom and front edge of hood, Fig.9. After hood

is positioned, fully tighten the lower installation bracket

screw from step 7, Fig.8-1.

Fig.9 Fig.10

$¿OOHUSDQHOLVLQFOXGHGWRDFFRPRGDWHPXOWLSOHFDELQHW

depths. Inside the hood are (2) thumb screws located

on the left and right sides at the back of the hood,

Fig.10A. Turn each thumb screw clockwise to push

WKH¿OOHUSDQHOWRZDUGVWKHZDOO)LJ%7LJKWHQWKXPE

VFUHZVXQWLO¿OOHUSDQHOPHHWVWKHZDOODQGLVVHFXUHGLQ

SODFH6HHKRRGVSHFL¿FDWLRQVRQSDJHIRUVXSSRUWHG

cabinet depths.

A

B

1

2

1

Installation – Installing the Hood

12

www.zephyronline.com

A

10) Place 6” round ducting over blower collar and secure

with aluminum duct tape. If using hood in ductless

recirculating mode turn to page 13.

Install electrical wiring. Note: A cable lock (not

included) may be required by local codes. Check

with local requirements and codes, purchase and install

appropriate connector if necessary.

Make sure no packing material is inside hood. Power

up hood check for leaks around duct tape and verify all

functions.

Fig.11 Fig.12A

11) Secure (2) 1” wood screws (A) into the screw holes on

WKHOHIWDQGULJKWVLGHVRIWKH¿OWHURSHQLQJ7KLVZLOOVHFXUH

the hood body to the cabinet base and prevent the hood

from shifting after installation.

Fig.12B

12) Place front panel back on hood body and secure in

place by using the (10) screws previously removed from

step 2.

13

Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed.

When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust

IURPFRRNLQJDUHGUDZQDQG¿OWHUHGE\DQRSWLRQDOFKDUFRDO¿OWHU7KHDLULVWKHQSXUL¿HGDQGUHFLUFXODWHGEDFN

within the home.

We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct

ZRUNLISRVVLEOH7KHKRRGLVPRVWHIIHFWLYHDQGHI¿FLHQWDVDQH[KDXVWKRRG2QO\ZKHQWKHH[KDXVWRSWLRQ

is not possible should you recourse to converting the hood into a recirculating hood.

:KHQFRQYHUWHGWREHDUHFLUFXODWLQJKRRGDFKDUFRDO¿OWHULVUHTXLUHGRQWRSRIWKHGHFRUDWLYHPHVK¿OWHU

2UGHUDFFRUGLQJWRLWVSDUWQXPEHUEHORZ7KHGHFRUDWLYHPHVK¿OWHULVLQWHQGHGWRFDSWXUHUHVLGXHIURP

FRRNLQJDQGWKHRSWLRQDOFKDUFRDO¿OWHUKHOSVWRSXULI\IXPHVH[KDXVWHGIURPFRRNLQJIRUUHFLUFXODWLRQ

RECIRCULATING KIT (REQUIRED IF NOT DUCTED OUTSIDE THE HOME)

.LWLQFOXGHVFKDUFRDO¿OWHUEUDFNHWVDQGUHWXUQDLUYHQW

Hood Model Part No. Filters in Pkg.

ZGE (all models) ZRC-00GE 1

1. Purchase recirculating kit per the part number above.

 5HPRYHGHFRUDWLYHPHVK¿OWHUIURPKRRGDQGSODFHFKDUFRDO¿OW H U  R Q  W R S  R I  

PHVK¿OWHU6HFXUHFKDUFRDO¿OWHUWRPHVK¿OWHUE\XVLQJWKHVXSSOLHGZLUH

brackets as shown in Fig.13.

5HLQVWDOOGHFRUDWLYHPHVK¿OWHU

Charcoal Filter Replacement

Hood Model Part No. Qty to Order

ZGE (all models Z0F-C0GE 1

Installation – Ductless Recirculation

4. In order to recirculate the air properly, a return air vent must be installed to

allow recycled air to be returned to the kitchen, Fig. 14. Ducting must be run

from the blower to the return air vent. The return air vent can be positioned

RQWRSRIWKHFDELQHWRULQDVRI¿WFHLOLQJ

5. Enable Charcoal Filter Change indicator on control panel. See page 15.

 &KDUFRDO¿OWHUPXVWEHUHSODFHGDIWHUHYHU\KRXUVRIXVHRUDSSUR[LPDWHO\

every 3 to 4 months based on an average daily use of 1 hour of cooking time)

The microprocessor in the controls, when set, will elapse and count usage

WLPHDQGLQGLFDWHZKHQFKDUFRDO¿OWHUUHSODFHPHQWLVUHTXLUHGHYHU\KUV

Fig.13

Fig.14

14

www.zephyronline.com

Blower On/Off

By pressing , the blower is switched On and Off. When switched On, the blower will

operate at the last setting before it was switched Off. When switched Off the entire hood

powers Off, including the lights.

Speed Selection

The 3 speed levels are selected by pressing to decrease and to increase speed

level. The display indicates speed level selected. Pressing when the hood is Off will

also switch the blower On.

Delay Off

Delay Off is used for programmed shut down of blower and lights 5 minutes after the function

is activated. Press once and a dot will appear in the lower right side of the Display

indicating the function is on. The hood will change to Speed 1 and shut down after 5 minutes.

Lights Normal/Dim/Off

Switch lights on to Normal by pressing once, again to Dim and again to switch Off.

1

2

3

4

Display

Displays blower speed level, delay off status, mesh filter clean and charcoal filter replace notification.

5

Lights Normal/Dim/Off

5 Min Delay Off

Display (speed level, delay of

f, filter clean/replace)

Speed Selection

Blower On/Off

NOTE: Blower and lights will automatically shut off when the glass is closed. The hood

also has a built in memory function that will automatically turn the blower and

lights on at the last setting when the glass is pulled open.

Blower will not operate while the glass is closed but the lights will still function.

The decorative mesh filter is required to be cleaned frequently and as recommended in

order to maintain blower efficiency. If improperly maintained, residue from cooking will

sift through filter and cause damage to hood blower and other sensitive components by

possibly clogging duct work and creating a fire hazard.

Features & Controls – Touch Controls

15

Decorative Mesh Filter Clean Reminder (metal mesh filter)

Whether your hood is installed as an exhaust or purifying unit, a decorative mesh filter is fitted by the factory. This

mesh filter is intended to filter out residue from cooking. It need not be replaced on a regular basis but is required to

be kept clean. After every 30 hours of use the Filter Clean Reminder function in the microprocessor will automati-

cally remind you by a flashing when the mesh filter needs to be cleaned. The filter can be cleaned by hand

with non-abrasive soap or in a dishwasher. A heavily soiled filter should also be soaked in grease cutting

detergent prior to cleaning.

Decorative Mesh Filter Clean Indicator

When flashes on display, the mesh filter installed is

required to be cleaned. This will occur after every 30

hours of use.

Re-setting Function

Reset the filter clean reminder timer when filter is cleaned

and re-installed. With hood off, press and hold for

approximately 5 seconds until on display disappears

. . The filter clean reminder function is now reset

and a new 30 hours elapse cycle is initiated.

F

Clean Filters

display < F > flashes

F

hold 5 sec. display from < F > to < >

To Reset

F

Charcoal Filter Replace Reminder (charcoal filter, if installed)

When your hood is installed as a recirculating unit it must be fitted with a charcoal filter to purify exhaust and fumes

from cooking and then recirculate the air within the home. This charcoal filter must be replaced after every 120 hours

of use. The charcoal filter should never be cleaned or placed in a dish washer.

The charcoal filter replace reminder function in the microprocessor needs to be switched on. When switched on, the

microprocessor will elapse and count usage time. When charcoal filter replacement is needed a flashing will

appear on the display.

C

Setting the Charcoal Filter Replace Reminder

With hood off, hold for approximately 5 seconds.

The display will change from (exhaust mode) to

(recirculating mode). This indicates that the elapse

timer function is switched on and charcoal filter is being

used.

Charcoal Filter Replace Indicator

When the display starts flashing, the charcoal filter

needs to be replaced. Purchase replacement charcoal

filters from Zephyr.

Re-setting Function

After charcoal filter is replaced, with hood off, press and

hold for apprimately 5 seconds until on the

display disappears . The filter change reminder is

now re-set and a new 120 hour elapse cycle is initiated.

C

hold 5 sec. display from < - > to < C >

Set Mode

display < C > flashes

Change FIlter

C

hold 5 sec. display from < C > to < >

To Reset

C

Features & Controls – Filter Clean and Replace Reminder

16

www.zephyronline.com

Features & Controls – Remote Control (Optional)

FCC Caution:7RDVVXUHFRQWLQXHGFRPSOLDQFHDQ\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHSDUW\

responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part

15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful

interference, and (2) This device must accept any interference received, including interference that may cause

undesired operation.

Remote control is sold as an optional accessory. Purchase Zephyr part number: 14000005

This remote control may operate in humid environments, but not when placed on a wet surface.

Blower On/Speed Selection

By pressing , the blower is switched On. Press again to cycle through all

three blower speeds.

Blowers On/Hood Off

By pressing , the blowers will power on at the last speed setting. Press

again and the entire hood will power off, including lights.

Delay Off

Lights On/Dim/Off

Switch lights On by pressing once, again to dim and again to switch Off.

Blower On/

Speed Selection

1

2

3

4

Blower On/

Power Off

2

5 Min Delay Off

3

Lights On/Dim/Off

4

By pressing , the blower and lights will enter Delay Off mode. A dot will

appear in the lower right corner of the power pack display indicating the

function is on. The blower will change to speed 1 and shut down after 5

minutes.

A

-

+

SYNCHRONIZATION: To create a unique link between your range hood and remote control please follow the below steps:

1. With range hood off, press and hold the “lights” button on the range hood until the letter “F” shows on the display screen.

2. Press the “lights” button on the remote, the lights on the hood will turn on. The synchronization is complete.

REMOTE CONTROL FEATURES:

The RF remote control is equipped with a magnet for easy storage. The remote may be placed on any magnetic surface such

as a refrigerator or the Zephyr remote holder. Maximum remote control communication distance from power pack is 15 feet.

REMOTE CONTROL MAINTENANCE:

Clean the remote control using non abrasive detergents

Follow instructions below for replacing battery.

8VLQJDVPDOOÀDWKHDGVFUHZGULYHUUDLVHWKHFRYHURIWKHEDWWHU\GRRUA)

in order to access the battery compartment.

Remove the battery and replace with Type A23 12V.

Negative end of battery should face the spring inside the remote.

Replace battery door and recycle old battery.

17

SURFACE MAINTENANCE:

Periodically clean with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent

steel wool or scouring pads which will scratch and damage surface.

For heavier soil use liquid degreaser.

After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners to polish and buff

out the stainless luster and grain. Always scrub lightly with clean cotton cloth and with the grain.

Do not use any product containing chlorine bleach. Do not use “orange” cleaners.

Decorative Mesh Filters

7KHPHVK¿OWHULQVWDOOHGE\WKHIDFWRU\LVLQWHQGHGWR¿OWHURXWUHVLGXHDQGJUHDVHIURPFRRNLQJ,WQHHGQRW

be replaced on a regular basis but is required to be kept clean.

Filter should be cleaned after every 30 hours of use or once a month.

Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if

heavily soiled.

'U\¿OWHUDQGUHLQVWDOOEHIRUHXVLQJKRRG

Replacing Mesh Filter

6KRXOG¿OWHUZHDURXWGXHWRDJHDQG

prolonged use, replace with the following part

number:

Hood Model: Part No. Qty. to Order.

All ZGE Models 50200036 1

5HSODFHDQ\GDPDJHG¿OWHUWKDWKDVSXQFWXUHG

or broken mesh or damaged frame.

7RUHPRYHGHFRUDWLYHPHVK¿OWHU

1. Pull down on handle.

7LOW¿OWHUGRZQDQGUHPRYHIURPKRRG

2

1

Maintenance – Hood and Filter Cleaning

18

www.zephyronline.com

REPLACING LIGHT BULBS

CAUTION: Light bulb becomes extremely hot when turned on.

DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.

Make sure all power is turned off and bulbs are not hot.

Remove by turning bulb counter-clockwise. Note: Bulb does not unscrew; it turns 60 degrees,

stops and falls out.

,IEXOEVDUHGLI¿FXOWWRWXUQGXHWRSURORQJHGXVH¿UPO\DWWDFKDJODVVVXFWLRQFXSDSSUR[LPDWHO\WKHGLDPHWHURI

the bulb or use a rubber/latex glove to grip the bulb and turn counter clockwise.

Replacement bulbs are available at specialty lighting stores. Purchase type (MR16) GU-10 50W halogen.

For Zephyr part numbers please turn to page 21 of the manual.

Maintenance – Lights

Page is loading ...

Zephyr Genova ZGE-E30AS290 Installation guide

Related papers

Other documents