Hunter 23775 User manual

HEPAtech

®

Air Purication System

Air Purier Model HEPAtech

®

Filter Pre-Filters

30057A, 30061 30928 30901

30067A, 30124A 30928 30901

www.hunterfan.com

Model 30067A, 30124AModel 30057A, 30061

ENGLISH

Page 2

ESPAÑOL

Página 9

FRANÇAIS

Page 17

2

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THIS AIR

PURIFIER AND SAVE THESE IMPORTANT INSTRUCTIONS

1. This Air Purier is designed for use on a at, level surface and may not

work properly on an uneven surface. ALWAYS place this Air Purier

on a rm, level surface. ALWAYS place the Air Purier at least

six (6) inches away from walls and heat sources such as

stoves, radiators, or heaters.

2. Place the Air Purier in an area that is out of the reach of children.

3. Before using the Air Purier, extend the cord and inspect for any signs of

damage. DO NOT use the product if the cord has been damaged.

4. This product has a polarized plug (one blade is wider than the other) as

a safety feature. This plug will t into a polarized outlet only one way. If

the plug does not t fully into the outlet, reverse the plug. If it still does not

t, contact a qualied electrician. DO NOT attempt to defeat or override

this safety feature.

5. ALWAYS UNPLUG the Air Purier when it is not in operation, while

the lter is being changed, and while it is being cleaned.

6. DO NOT tilt or move the Air Purier while it is in operation. Shut off

and unplug before moving.

7. DO NOT immerse the Air Purier in water as permanent damage

will occur. Refer to and follow the CLEANING AND FILTER

REPLACEMENT instructions.

Introduction

Thank you for purchasing the HEPAtech

®

Air Purication System from Hunter

Fan Company. You have purchased our latest development in portable Air

Purication Systems. This system has been developed to improve the quality of

the air you breathe.

Our HEPAtech

®

Air Purication System out performs other air purication

systems by quickly and effectively removing dust, smoke, and pollen particles

as small as .1 microns in size. Room air is pulled in through the front grill and

cleaned across the HEPAtech

®

lter. Clean air is then released out the top grill

in order to avoid stirring up settled particles.

Using the Ionizer

Using the ionizer improves the quality of air in the room. Negative ions are

released into the air and positively charged dust, smoke, and pollen particles

are attracted to the negative ions. These particles settle out of the air and

can be vacuumed up during normal cleaning. These particles are also more

easily captured by the HEPAtech

®

lter as they pass through the HEPAtech

®

Air Purication System. To ensure the best air circulation in the room, we

recommend that you place your air purier six inches away from any walls.

3

Tabs for

opening the

front grill

HEPAtech

®

Filter

Pre-Filter

Front

Grill

Figure 2 - Model 30067A, 30124A

Figure 3

Hook Tape

Grill Vents

Hook Tape

Front

Grill

Pre-Filter

HEPAtech

®

Filter

Buttons for

opening the

front grill

Setting Up Your Air Purier

1. Remove your air purier from the box and take it out of the clear plastic

protective bag.

2. Place your HEPAtech

®

Air Purier on a rm, at oor.

3. Before turning the Air Purier ‘on,’ open the front grill.

• For Model 30057A, 30061: To release the front grill, press the buttons

on the side until the front grill slides easily over the buttons. (Refer to Figure

1.)

• For Model 30067A, 30124A: To release the front grill, place your

ngers behind the tabs and pull forward. (Refer to Figure 2.)

4. Next, check the HEPAtech

®

lter by pressing rmly on all four corners of the

lter to ensure that it is fully inserted into the lter opening.

5. The carbon pre-lter is mounted inside of the front grill with “hook” tape.

Conrm that it covers the grill vents. (Refer to Figure 3.)

6. Place the lter installation reminder sticker on the inside edge of the front

grill. Circle the month and write the year of installation for the pre-lter and

HEPAtech

®

lter.

7. Replace the lter and front grill. Be sure that the bottom grill tabs are in

position rst, and then push the top of the grill forward until it is closed. The

unit is now ready for normal operation. NOTE: This unit will not operate

unless the door is placed in the correct position.

8. Plug the unit into a 120V electrical outlet.

AIR PURIFIER PARTS

Figure 1 - Model 30057A, 30061

4

Operating Your Air Purier

On/Speed Control: Rotate the Speed Control knob to set the desired

speed. A setting of zero (0) indicates that the unit is off, one (1) is low speed,

two (2) is medium speed, and three (3) is high speed. The fan speed can be

adjusted at any time.

Ionizer: Press this button to turn ‘on’ the ionizer. When the ionizer is ‘on’,

the green light near the button will be illuminated.

Pre-Filter and Filter Timers

This air purier contains timers that indicate when the pre-lter and lter

should be changed. The timer automatically counts the number of hours that

each lter has been in use. When the pre-lter counter reaches 1400 hours

(approximately three months of use), the pre-lter indicator will be lit to show

that the pre-lter should be changed. When the HEPAtech

®

lter counter

reaches 2800 hours (approximately four to six months of use), the HEPAtech

®

lter indicator will be lit to indicate that the lter should be changed. The exact

life of the pre-lter and lter will depend upon the environment. If necessary,

the lters should be changed more frequently.

To reset the pre-lter or lter timers when one indicator (or both) is

lit:

1. Change the lter and/or pre-lter as described in the Maintenance

section of the manual.

2. To reset the counter to zero hours and turn off the indicator, simply press

and hold the lter reset key for three seconds. If both the pre-lter and lter

indicators are lit, the reset key will rst turn off the pre-lter indicator. Then,

you must release the reset key and then press and hold the lter reset key

again for three seconds to turn off the lter indicator.

To reset the pre-lter or lter timers before the indicators are lit:

In some environments, you may want to change the pre-lter or lter more

frequently than indicated by the lter indicators. This procedure allows you to

reset the pre-lter or lter counter before the indicators are lit.

1. Change the lter and/or pre-lter as described in the Maintenance

section of the manual.

2. Now, you must choose which timer you want to reset. Press and hold the

lter reset key (approximately three seconds) until the pre-lter indicator

ashes. Press the reset key again to alternate between the two indicators.

The timer that will be reset is designated by the ashing indicator.

3. Once you have the correct indicator ashing, press and hold the reset key

for three seconds to reset that timer to zero hours. The indicator will stop

ashing when it has been reset. If needed, repeat these steps to reset the

other timer.

5

Cleaning and Filter Replacement

1. Clean the outside of the unit with a soft, damp cloth. The front grill can be

removed and cleaned in soapy water. Remove the pre-lter before cleaning

the front grill.

2. At least every 90 days, replace the carbon pre-lter. This

is necessary to maintain proper odor removing and overall ltration

performance. If necessary, it can be changed more often. Mark the new

lter installation sticker included with the new carbon pre-lter. Be sure to

remove any plastic wrapping that may be on the new lter

before you place it in the Air Purier.

3. While replacing the pre-lter, you should view the condition of the

HEPAtech

®

Filter. Compare the lter to the color coded chart that is on the

inside of the housing. If the lter matches the dark color on the chart, you

should remove the lter and replace it with a new lter. Mark the new lter

installation sticker included with the new HEPAtech

®

Filter. Depending

on use and environment, the HEPAtech

®

Filter should last

four to six months.

4. Gently pull on the lter to remove it from the unit. While removing the lter,

note the directional arrows printed on the top of the lter. The new lter will

be installed with the same orientation. Once removed, the used lter can be

discarded.

5. Remove the new lter from its wrapping and look at the directional arrows

printed on the side of the lter. Install the lter with arrows pointing towards

the unit. Press the lter rmly into the air purier. To avoid damaging the

lter media, you should press on the frame of the lter only.

6. If you notice a decrease in air output or an increase in noise, the HEPAtech

®

Filter may be clogged. Replace it with a new HEPAtech

®

Filter.

Replacement Filters

To obtain a replacement filter for your Air Purifier, call 1-800-4Hunter

for your nearest retailer or Hunter Customer Service at (US) 1-888-830-

1326, (Canada) 1-866-268-1936. Please be prepared to tell the operator

the model number of your Air Purier and the model number of the lter

you need to replace. Visit our website at www.hunterfan.com.

Hunter Air Purier Model No.: 30057A 30067A, 30061

30124A

Pre-Filter Replacement Model No.: 30901 30901 30901

HEPAtech

®

Filter Replacement Model No.: 30928 30928 30928

6

To learn more about Hunter Fan Company products,

please see our Web page at:

www.hunterfan.com

Hunter Original

®

Programmable

Thermostat

The Care-Free

Humidier

™

Carbon

Pre-Filter

HEPAtech

®

Filter

99.97% – .1

Microns

Dust &

Irritants

Pollen &

Allergens

Odors Bacteria Pet Hair &

Dander

Ionizer

How the HEPAtech

®

Air Purication System Works

As the air is pulled into the purier, the activated carbon pre-lter absorbs odors

and catches large particles. Then, the air travels through the HEPAtech

®

lter where

the smaller particles are collected. Then, the ionizer releases negative ions into

the air that attract positively charged dust, smoke, and pollen particles. Finally, the

clean, puried air is released back into the room.

Other Home Comfort Products from Hunter

7

(Continued)

Hunter Fan Company

HEPAtech™ Air Purication System

5 YEAR LIMITED WARRANTY

The Hunter Fan Company makes the following limited warranty to the original

residential user or consumer purchaser of the HEPAtech™Air Purication System:

If any part of your HEPAtech™ Air Purication System (“Air Purier”) motor fails

during the rst ve (5) years from the date of installation due to a defect in mate-

rial or workmanship, we will provide a replacement Air Purier free of charge.

Installation is deemed to occur at the date of purchase.

If the Air Purier cord, ionizer, or front grill fails any time within one (1) year after

installation due to a defect in material or workmanship, we will replace or, at our

option, repair the unit free of charge at our nearest service center or at our Ser-

vice Department in Memphis, Tennessee. You will be responsible for all parts and

labor costs after this one-year period.

IF THE ORIGINAL RESIDENTIAL USER OR CONSUMER PURCHASER CEASES TO OWN

THE AIR PURIFIER, THIS WARRANTY AND ANY IMPLIED WARRANTY WHICH THEN

REMAINS IN EFFECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED.

NO WARRANTY, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANT-

ABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT TO THE

FILTER MATERIAL OR CARBON FILTER.

THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF

ANY IMPLIED WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO

THE MOTOR IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET

FORTH ABOVE.

This warranty is voided if the air purier is not purchased and used in the USA or

Canada.

This warranty excludes and does not cover defects, malfunctions or failures of the

Air Purier which were caused by repairs by persons not authorized by us, use of

parts or accessories not authorized by us, mishandling, modications, or damage

to the Air Purier while in your possession, or unreasonable use, including failure

to provide reasonable and necessary maintenance. This warranty does not cover

Air Puriers used in commercial applications. There are no express or implied war-

ranties as to commercial purchasers or users.

To obtain service, contact the nearest Hunter authorized service center or the

Hunter Fan Company Service Department, 7130 Goodlett Farms Pkwy Suite 400,

Memphis, Tennessee 38016, 1-888-830-1326. For the name of our nearest au-

thorized Hunter Fan Company Service Center, write to the Hunter Fan Company

at the preceding address. You will be responsible for insurance and freight or

other transportation to our factory service center. We will return the Air Purier

freight prepaid. The Air Purier should be properly packaged to avoid damage in

transit since we will not be responsible for any such damage. Proof of purchase

is required when requesting warranty service. The purchaser must present sales

receipt or other document that establishes proof of purchase.

8

Hunter Fan Company

2500 Frisco Avenue

Memphis, Tennessee 38114

USA

Printed in China & Taiwan

IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR DIRECT, INDIRECT, SPE-

CIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES IN EXCESS OF THE PURCHASE PRICE

OF THE AIR PURIFIER. YOUR SOLE REMEDY WILL BE REPAIR OR REPLACEMENT AS

PROVIDED ABOVE.

SOME AMERICAN STATES AND CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS

ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

SOME AMERICAN STATES AND CANADIAN PROVINCES DO NOT ALLOW THE EXCLU-

SION OR LIMITATION OF DIRECT, INDIRECT SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

SOME AMERICAN STATES AND CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION

OR INVALIDITY OF EXPRESS OR IMPLIED WARRANTIES IF THE USER CEASES TO OWN

THE AIR PURIFIER, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE

OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.

ESPAÑOL

www.hunterfan.com

Modelo de

puricador de aire Filtro HEPAtech

®

Pre-Filtros

30057A, 30061 30928 30901

30067A, 30124A 30928 30901

HEPAtech

®

Sistema de

puricación de aire

Modelos 30067A, 30124A

Modelos 30057A, 30061

9

Page is loading ...

FRANÇAIS

D E P U I S

www.hunterfan.com

Modèle de

puricateur d’air Filtre HEPA Pré-ltres

30057A, 30061 30928 30901

30067A, 30124A 30928 30901

HEPAtech

®

Système

puricateur d’air

Modèles 30067A, 30124A

Modèles 30057A, 30061

17

Page is loading ...

Hunter 23775 User manual

Hunter 23775 User manual

in other languages

Related papers

Other documents