NEC NEC LCD 1711M Owner's manual

Page is loading ...

English

1 – User’s Manual

Table of Contents

Recommended Use.............................................................................2

Safety Precautions and Maintenance .............................................2

Introduction..........................................................................................4

About the Product...........................................................................4

Package Overview..........................................................................5

Declaration of the Manufacturer ..........................................................5

Declaration of the Manufacturer .....................................................5

Installation ...........................................................................................6

Product Overview ...........................................................................6

VESA Mount on your monitor .........................................................7

Start Your Installation ......................................................................8

User Controls ....................................................................................10

Front Panel Controls.....................................................................10

How to Use the OSD Menus.........................................................11

On-Screen Display Menus............................................................ 11

Appendix ...........................................................................................13

Troubleshooting............................................................................13

Warning Signal .............................................................................14

Product Dimensions .....................................................................15

Compatibility Modes .....................................................................16

FCC Statement ..................................................................................84

TCO’99..............................................................................................85

LCD1711M – 2

English

Recommended Use

• DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and

opening or removing covers may expose you to dangerous shock hazards or other

risks. Refer all servicing to qualified service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch

dangerous voltage points, which can be harmful or fatal or may cause electric

shock, fire or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may cause

shock or fire.

• Do not place this product on a sloping or unstable cart, stand or table, as the

monitor may fall, causing serious damage to the monitor.

• Do not place any objects onto the monitor and do not use the monitor outdoors.

• The inside of the flourescent tube located within the LCD monitor contains

mercury. Please follow the bylaws or rules of your municipality to dispose of the

tube properly.

Immediately unplug your monitor from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

• Do not bend power cord.

• Do not use monitor in high temperatured, humid, dusty, or oily areas.

Safety Precautions and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE

FOLLOWING WHEN SETTING UP AND USING

THE LCD COLOR MONITOR:

• If monitor or glass is broken, do not come in contact with the

liquid crystal and handle with care.

• Allow adequate ventilation around the monitor so that heat can

properly dissipate. Do not block ventilated openings or place the

monitor near a radiator or other heat sources. Do not put

anything on top of monitor.

• The power cable connector is the primary means of detaching

the system from the power supply. The monitor should be

installed close to a power outlet which is easily accessible.

• Handle with care when transporting. Save packaging for

transporting.

CAUTION

3 – User’s Manual

Recommended Use – continued

• For optimum performance, allow 20 minutes for warm-up.

• Adjust the monitor height so that the top of the screen is at or

slightly below eye level. Your eyes should look slightly

downward when viewing the middle of the screen.

• Position your monitor no closer than 40 cm and no further away

than 70 cm from your eyes. The optimal distance is 58 cm.

• Rest your eyes periodically by focusing on an object at least

6 m away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to minimize

glare and reflections. Adjust the monitor tilt so that ceiling lights do not reflect on

your screen.

• If reflected light makes it hard for you to see your screen, use an anti-glare filter.

• Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any

cleaning solution or glass cleaner!

• Adjust the monitor ’s brightness and contrast controls to enhance readability.

• Use a document holder placed close to the screen.

• Position whatever you are looking at most of the time (the screen or reference

material)directly in front of you to minimize turning your head while you are typing.

• Avoid displaying fixed patterns on the monitor for long periods of time to avoid

image persistence (after-image effects).

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomics benefits, we recommend the following:

• Use the preset Size and Position controls with standard signals

• Use the preset Color Setting

• Use non-interlaced signals with a vertical refresh rate between 60 - 75 Hz

• Do not use primary color blue on a dark background, as it is difficult to see and

may produce eye fatigue to insufficient contrast

• Image Persistence: Image persistence is when a residual or “ghost” image of a

previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’

image persistence is not permanent, but constant images being displayed for a

long period of time should be avoided.

To alleviate image persistence, turn off the monitor for as long as the previous

image was displayed. For example, if an image was on the monitor for one hour

and a residual image remains, the monitor should be turned off for one hour to

erase the image.

NOTE: As with all personal display devices, NEC-Mitsubishi Electronics Display-

Europe recommends using a moving screen saver at regular intervals whenever

the screen is idle or turning off the monitor when not in use.

CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR

CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK

THE FOLLOWING WHEN YOU POSITION THE MONITOR.

English

Introduction

LCD1711M – 4

About the Product

Having a 17” flat panel screen with an active matrix, thin-film

transistor (TFT) liquid crystal display (LCD), this product also demonstrates

following outstanding features.

•

Analog signal input

•

Active matrix TFT LCD technology

•

1280 x 1024 addressable pixels

•

17” diagonal screen size

•

31.5 ~ 80 kHz horizontal scan

•

56 ~ 75 Hz refresh rate

•

VESA wall mountable

•

Auto-adjustment

•

Multilingual OSD user controls

•

Foldable stand design brings users the conveniences for easy storage

and VESA Mounting applications

•

VESA DPMS power saving

•

Built-in speakers for multimedia application

•

Kensington lock capability

•

Power Supply: AC 100 - 120 V / 220 - 240 V 50/60 Hz

•

Current Rating: 0.8 A @ 100 - 120 V / 0.4 A @ 220 - 240 V

•

Weight: 4.9 kg (10.8 lbs)

•

Environmental Considerations:

Operating Temperature: 5 °C to 35 °C

Humidity: 30 % to 80 %

Altitude: 0 to 3,050 m

Storage Temperature: -10 °C to +60 °C

Humidity: 10 % to 85 %

Altitude: 0 to 12,000 m

English

5 – User’s Manual

Package Overview

LCD Display

Power Adapter

Power Cord

Audio-In Cable

Declaration of the Manufacturer

We hereby certify that the

monitor LCD1711M is in compliance

with Council Directive 73/23/EEC:

– EN 60950

Council Directive 89/336/EEC:

– EN 55022

– EN 61000-3-2

– EN 61000-3-3

– EN 55024

and marked with:

NEC-Mitsubishi Electric Visual

Systems Corporation

4-13-23, Shibaura,

Minato-Ku

Tokyo 108-0023, Japan

CD ROM

User’s Manual

LCD 1711M

User’s Manual

Bedienerhandbuch

Manual del usuario

Manuel Utilisateur

Manuale utente

English

VGA Signal Cable

LCD1711M – 6

Installation

Product Overview

Front View

Rear View

English

LCD Display

Speakers

Panel

Controls

Stand

Kensington Lock

Audio-In

Connector Ports

VGA input

DC

Power-In

7 – User’s Manual

VESA Mount on your monitor

This monitor conforms to the VESA Flat Panel Mounting Physical Mounting

Interface Standard which defines a physical mounting interface for flat

panel monitors, and corresponding standards for flat panel monitor mount-

ing devices, such as wall and table arms. The VESA mounting interface is

located on the back of your monitor.

To mount the monitor on a swing arm or other mounting fixture, follow the

instruction included with the mounting fixture to be used.

Caution! Please select the proper screws!

The depth from plastic back cover to the bottom of the screw hole

is 8 mm. The spec is M4 screw. To fulfil the safety requirements

the monitor must be mounted to an arm which guarantees the

necessary stability under consideration of the weight of the moni-

tor. The LCD monitor shall only be used with an approved arm

(e.g. GS mark).

VESA

Mounting

Interface

Slots

100 mm

English

Connecting the Display (Figure 8.1)

To set up this display, please refer to the following figure and procedures.

1. Be sure all equipments are off.

2. Connect the DC power cord to the power connector; plug one end of the

AC power cord into the power adapter, and then the other end into an

electrical outlet (1).

3. Connect the VGA signal cable from display VGA input connector to the

15-pin connector of your host computer and tighten the screws (2).

4. Connect the Audio-In cable from audio input port of your display to the

Audio-out port of your computer (3).

5. Turn on your computer and display.

LCD1711M – 8

Notice: To ensure the LCD display can work well with your computer,

please configure the display mode of your graphic card to make it

less than or equal to 1280 x 1024 resolution and make sure

timing of the display mode is compatible with the LCD display.

We have listed the "Compatibility Modes" of this LCD display in

appendices for your reference.

Start Your Installation

English

9 – User’s Manual

Figure 8.1

English

(1) Power Adapter

& Power Cord

(2) VGA Cable

(3) Audio-In cable

User Controls

LCD1711M – 10

Front Panel Controls

nocI/.oNlortnoCnoitcnuF

)1( M nottuBuneM.sunemDSOehtyalpsiD

)2( S otuA/tceleS.1morfsmetitnemtsujdaehttcelesoT

.sunemDSO

.2”tnemtsujdAotuA“ehtetavitcaoT

mumitponaniatbootnoitcnuf

.egami

)3(rewoPDCLehtforewopehtffo/nohctiwS

.yalpsid

)4(DELrewoP.1siyalpsidehtsetacidnineerG

.nodenrut

.2nisiyalpsidehtsetacidnirebmA

.edomgnivas-rewop

)5( – ssenthgirB.2/suniM.1.1stnemtsujdaehtfoeulavesaerceD

.smeti

.2.egamifossenthgirbehttsujdA

)6( + ffO/nOetuM.2/sulP.1.1tnemtsujdaehtfoeulavesaercnI

.smeti

.2noitcnufemulovehtekaM

.evitceffe/evitceffenI

English

(4)

(1)

(2)

(3)

(5)

(6)

11 – User’s Manual

How to Use the OSD Menus

1. Press the "M" button to display the OSD Menus. Press the "M" button

to move between the OSD Menus. Press "S" to enter the functions to

be adjusted and then press "S" to move between functions.

2. Adjust the value of the option by pressing "–" and "+". Press "S" to

confirm your choice.

3. To exit the OSD Menus, move to "Fourth OSD Menu" and press "M".

On-Screen Display Menus

First OSD Menu:

•

Auto-Adjustment

Choose this function to obtain an optimum image.

•

Contrast

Adjusts the contrast of the display image.

•

Horizontal Position

Changes the horizontal position of the image.

•

Vertical Position

Changes the vertical position of the image.

•

Frequency

Changes the display data frequency to match the frequency of your

graphic card. When you are experiencing vertical flickering bar, use this

function to make an adjustment.

•

Tracking

Synchronizes the signal timing of the display to that of the graphic card.

When you are experiencing unstable to flickering image, use this func-

tion to make an adjustment.

English

LCD1711M – 12

Second OSD Menu:

•

Display Mode

Selects this function to demonstrate the display resolution, vertical

refresh, and horizontal scan of the current mode

•

OSD Off-Time

Adjusts the time period for OSD menu disappear.

•

Language

Chooses the language you need.

•

Text-Graphic

Toggles between VGA text mode (mode M03H) and graphic mode

(mode M13H).

•

Sharpness

Adjust the sharpness of the image.

(This function is disabled when input signal is 1280 x 1024.)

•

Reset

Returns the display parameters of the current mode to its factory default

settings.

Third OSD Menu:

•

Volume

It allows you to control the volume sound.

•

Mute

It allows you to disable the sound immediately.

Fourth OSD Menu:

•

Color Setting

Adjusts the color temperature.

•

Color Adjustment-Red

It allows you to adjust the red color of the display.

•

Color Adjustment-Green

It allows you to adjust the green color of the display.

•

Color Adjustment-Blue

It allows you to adjust the blue color of the display.

English

Appendix

13 – User’s Manual

Troubleshooting

If you are experiencing trouble with the LCD display, refer to the following.

If the problem persists, please contact your local dealer or our service

center.

Problem: No image appears on screen.

•

Check that all the I/O and power connectors are correctly and well

connected as described in the "Installation" section.

•

Make sure the pins of the connectors are not crooked or broken.

Problem: Partial image or incorrectly displayed image.

• Check to see if the resolution of your computer is higher than that of the

LCD display.

• Reconfigure the resolution of your computer to make it less than or equal

to 1280 x 1024.

Problem: Image has vertical flickering line bars.

• Use "Frequency" to make an adjustment.

• Check and reconfigure the display mode of the vertical refresh rate of

your graphic card to make it compatible with the LCD display.

Problem: Image is unstable and flickering

• Use "Tracking" to make an adjustment.

Problem: Image is scrolling

• Check and make sure the VGA signal cable (or adapter) is well con-

nected.

• Check and reconfigure the display mode of the vertical refresh rate of

your graphic card to make it compatible with the LCD display.

Problem: Vague image (characters and graphics)

• Use "Frequency" to make an adjustment. If this problem still exists, use

"Tracking" to make an adjustment.

English

LCD1711M – 14

Warning Signal

Sometimes you probably will see the warning messages from this LCD

screen. This means that the LCD display cannot exactly receive the signal

from the computer graphic card.

There are three kind of situations that may happen. Please check the

connected cables or contact your local dealer for more information.

•

No Signal

This message means that the LCD display has been powered on but it

cannot receive any signal from the computer graphic card. Check all the

power switches, power cables, and VGA signal cable.

•

Going to Sleep

This message means that the LCD display is under the power saving

mode. In addition, the LCD display will go to this sleeping mode when

experiencing a sudden signal disconnecting problem.

•

Out of range

This message means that the signal of the computer graphic card is not

compatible with the LCD display. When the signal is not included in the

compatibility mode we have listed in the Appendices of this manual, the

LCD will display this message.

English

15 – User’s Manual

169.9 mm/6.57”

52 mm/2.05”

Product Dimensions

Front View

Side View

Top View

English

382.7 mm/15.07”

377.5 mm/14.86”

edoMnoituloseRycneuqerF.V

)zH(

ycneuqerF.H

)zHk(

AGV053x046075.13

AGV004x046075.13

AGV084x046065.13

AGV004x027075.13

AGVASEV084x046279.73

AGVASEV084x046575.73

AGVSASEV006x008652.53

AGVSASEV006x008069.73

AGVSASEV006x008271.84

AGVSASEV006x008579.64

AGXASEV867x4201064.84

AGXASEV867x4201075.65

AGXASEV4201x08210646

AGXSASEV4201x08210646

AGXSASEV4201x08215708

CLcaMelppA084x046769.43

TIcaMelppA084x046760.53

caMelppA426x238577.94

caMelppA867x4201572.06

LCD1711M – 16

Compatibility Modes

English

Page is loading ...

LCD1711M – 32

Kompatibilitätsmodi

-stätilibitapmoK

idom

sudoM

gnusölfuA

zneuqerF.V

)zH(

zneuqerF.H

)zHk(

AGV053x046075,13

AGV004x046075,13

AGV084x046065,13

AGV004x027075,13

AGVASEV084x046279,73

AGVASEV084x046575,73

AGVSASEV006x008652,53

AGVSASEV006x008069,73

AGVSASEV006x008271,84

AGVSASEV006x008579,64

AGXASEV867x4201064,84

AGXASEV867x4201075,65

AGXASEV867x4201570,06

AGXSASEV4201x08210646

AGXSASEV4201x08215708

CLcaMelppA084x046769,43

TIcaMelppA084x046760,53

caMelppA426x238577,94

caMelppA867x4201572,06

Deutsch

Page is loading ...

odoMnóiculoseR.VaicneucerF

)zH(

.HaicneucerF

)zHk(

AGV053x046075,13

AGV004x046075,13

AGV084x046065,13

AGV004x027075,13

AGVASEV084x046279,73

AGVASEV084x046575,73

AGVSASEV006x008652,53

AGVSASEV006x008069,73

AGVSASEV006x008271,84

AGVSASEV006x008579,64

AGXASEV867x4201064,84

AGXASEV867x4201075,65

AGXASEV867x4201570,06

AGXSASEV4201x08210646

AGXSASEV4201x08215708

CLcaMelppA084x046769,43

TIcaMelppA084x046760,53

caMelppA426x238577,94

caMelppA867x4201572,06

49 – Manual del usuario

Español

Modos de Compatibilidad

Page is loading ...

LCD1711M – 66

Modes de compatibilité

edoMnoituloséR.VecneuqérF

)zH(

.HecneuqérF

)zHk(

AGV053x046075,13

AGV004x046075,13

AGV084x046065,13

AGV004x027075,13

AGVASEV084x046279,73

AGVASEV084x046575,73

AGVSASEV006x008652,53

AGVSASEV006x008069,73

AGVSASEV006x008271,84

AGVSASEV006x008579,64

AGXASEV867x4201064,84

AGXASEV867x4201075,65

AGXASEV867x4201570,06

AGXSASEV4201x08210646

AGXSASEV4201x08215708

CLcaMelppA084x046769,43

TIcaMelppA084x046760,53

caMelppA426x238577,94

caMelppA867x4201572,06

Français

Page is loading ...

Modalità compatibili

odoMenoizulosiR.VazneuqerF

)zH(

.OazneuqerF

)zHk(

AGV053x046075,13

AGV004x046075,13

AGV084x046065,13

AGV004x027075,13

AGVASEV084x046279,73

AGVASEV084x046575,73

AGVSASEV006x008652,53

AGVSASEV006x008069,73

AGVSASEV006x008271,84

AGVSASEV006x008579,64

AGXASEV867x4201064,84

AGXASEV867x4201075,65

AGXASEV867x4201570,06

AGXSASEV4201x08210646

AGXSASEV4201x08215708

CLcaMelppA084x046769,43

TIcaMelppA084x046760,53

caMelppA426x238577,94

caMelppA867x4201572,06

Italiano

83 – Manuale utente

Page is loading ...

NEC NEC LCD 1711M Owner's manual

Related papers

Other documents