Gorenje E017AIS30E2BSB Owner's manual

Page is loading ...

GB

An introduction to the cooker hood –

Figure 1

1) Light switch

2) Motor speed switch

3) Work area light switch

4) Metal fat filter

5) Fat filter support

If you wish to remove the fat filter, please

refer to Figure 2.

Pull down the handle and pull out the metal fat filter. If

you wish to remove the fat filter support, press both

buttons B (Figure 3) and pull out the support.

Usage

You can use the cooker hood in two different ways:

- The air is pumped out of the cooking space.

- The air is filtered.

Operating in pumping mode

The air is sucked out of the room through a tube that is

attached by element D to the exahust aperture (Fig. 4).

Operating in filtering mode:

- The air is cleaned by an active carbon filter and is

then pumped back into the cooking space.

- Using the filter is neccessary if an exahust tube is

not available or impossible to install.

- Exahust itself is above the hanging element and is

connected to a tube which crosses the element itself.

Please adhere to the following rulse for operating in this

mode:

a) Order a filter with your supplier. Specify the exact

model of your cooker hood.

b) Remove the metal fat filter (Fig. 2).

c) Remove the frame by pushing the B buttons (Fig.

3). Please note that some filters are wrapped in

plastic foil to protect them during storage. Remove

the foil before installing the filter.

d) Insert the filter (one on each side, Fig. 5) and turn

the handle clockwise until it snaps into place.

e) Replace the frame and fat filter in reverse order.

Installation

Installation: The distance between the cooker hood and

the cooker should be at least 65 centimeters with electric

cookers and at least 75 cm with gas cookers or

combined electric/gas cookers.

Caution!

The intake air should never be directed to a smoke and

vapour exahust tube of an appliance that does not use

electricity as its source of energy! If the cooker hood is

used together with such appliances, please insure that

the room is properly ventilated. You should also never

use any open flame under the hood. Open flame can

damage the filters and cause a fire and should therefore

be avoided. Frying should also be supervised at all times

to make sure the oil does not catch fire.

Adhere to the local safety and technical regulations

regarding smoke emissions at all times!

We are not responsible for any problems, injuries or

fires which may occur if the instructions in this booklet

are not followed.

Tips for installing and using the hood:

- If a segment of the tube is horisontal, try tilting it

upwards a bit (aprox. 10%). That will increase the

efficiency of the cooker hood.

- This appliance is most effective when used in

pumping mode. Therefore, use it in this mode if

possible.

- This appliance is most effective when used with

short lengths of tubing (max. 4 meters) with few

curves.

Connecting this appliance to electrical

line:

The voltage provided by the electrical company must

be the same as indicated on the technical data label

which is on the inside of the cooker hood. If a plug is

provided, plug it into an outlet. Otherwise, install a bipolar

switch that adheres to safety regulations and has the

contacts at a distance of at least 3 milimeters. If the

outlet is hard to reach, install the bipolar switch anyway.

We are not responsible for any problems, injuries or

fires which may occur if the instructions in this booklet

are not followed.

Installing the cooker hood

When the cooker hood is ready, install it. This appliance

is intended to be installed into a cabinet or similar

supporting element.

- Make an opening on the bottom of the cabinet. Its

dimensions should be the same as those indicated

in Fig. 6.

Please follow these instructions to install the cooker

hood:

a) Remove the metal fat filter and the frame

b) Install the cooker hood into the opening.

c) Screw in the supplied screws into holes (F) (Fig. 6).

d) Replace the frame.

e) Install the metal fat filter (Fig. 2).

Usage instructions:

The fan has adjustable power settings. Use them

according to the concetration of smoke and vapor.

We recommend you turn on the hood 5 minutes before

you start cooking and leave it on for 15 minutes after

you have finished cooking.

Maintenance:

Before doing any maintenance, unplug the cooker hood.

Fat filter is to be cleaned monthly with a mild detergent

manually or using a dishwasher with low temperature

and short program.

To remove the fat filter (M), push the handles (N)

downwards.

Carbon filter (filtration version only)

This filter is neither washable nor renewable. It is used

to catch unpleasant smells that develop when cooking.

It should be mounted on the safety grille of the motor

and replaced every 4 months.

Installation: Install filter (P) on the safety grille and turn

GB

the handle in clockwise direction till it falls into place.

To remove, reverse the above procedure.

The carbon filter is not supplied. It has to be ordered

separately.

Cleaning:

The cooker hood should be cleaned regularly on the

outside as well as inside. Use a damp cloth with neutral

liquid cleaners. Do not use abrasive cleaners. Always

disconnect the hood before cleaning.

Changing the lightbulbs:

Remove the fat filter’s support grille and the filter to gain

access to the lightbulb cavity. Remove the burned-out

lightbulb and replace it with an oval lightbulb with

maximum power of 40 Watts (E14).

Use figures of the elements on the first few pages of

this booklet as a reference.

Follow the instructions in this booklet.

Fire hazard is increased f you do not adhere to the

instrucions for cleaning the cooker hood and replacing

and cleaning the filter.

Page is loading ...

Gorenje E017AIS30E2BSB Owner's manual

This manual is also suitable for

Gorenje E017AIS30E2BSB Owner's manual

in other languages

Related papers

Other documents