ProTemp Protemp PT-20F-DDF-A User's Manual And Operating Instructions

User’s Manual and

Operating Instructions

Please note the serial number of your fan, and write it on the back of this User’s Manual for future reference.

9500450290-13

668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996

Fax: (215) 891-8461 • Web: www.protemp.us • Email: [email protected]

This product meets and exceeds the requirements of OSHA 1910.212(a)(5), the standard which

regulates electric fan blade safety, and is certified under UL# E355088.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: Read and understand all of the instructions in this manual before assembling,

starting, or servicing the fan. Improper use of this fan can cause serious injury. Keep this manual for

future reference.

For General Ventilating Use Only. Do Not Use To Exhaust Hazardous Or Explosive

Materials And Vapors. Never use the fan in spaces which contain products such as

gasoline, solvents, paint thinners, dust particles, volatile or airborne combustibles, or any unknown

chemicals.

CAUTION

Model Numbers: PT-18W-DDF-A, PT-20F-DDF-A,

PT-20S-DDF, PT-24O-DDF, PT-24-DDF, PT-24-DDF-F,

PT-30-DDF, PT-30P-DDF-A, PT-30P-DDF-AF

User’s Manual and

Operating Instructions

Table of Contents

Safety Information................................................................................................................................. 3

Notes Page............................................................................................................................................4

Troubleshooting Guide........................................................................................................................19

Warranty................................................................................................................................Back Cover

5

18” Wall Fan

PT-18W-DDF-A

6-7

20” Floor Fan

PT-20F-DDF-A

8-10

20” Shop Fan

PT-20S-DDF

11

24” Barrel Fan

PT-24-DDF

PT-24-DDF-F

12-13

24” Omni Fan

PT-24O-DDF

14-16

30” Floor Fan

PT-30-DDF

17-18

30” Pedestal Fan

PT-30P-DDF-A

PT-30P-DDF-AF

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Safety Information

- Before operating always check fan for loose

or damaged parts. Inspect power cord for any

damage. Never use fan if any parts are

damaged or missing. Never use fan without

safety guards attached.

- Operate only on 120 volt 60 Hz (cycle) current

with a minimum of a 15 amp circuit.

- When used with an extension cord, use only

cord of proper size (Amp rating), UL listed, and

with receptacle to accept three prong grounded

plug furnished on the fan’s power cord. Always

keep power cord and extension cords away

from heat, oil, and sharp edges. Inspect cords

periodically and replace if damaged.

IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY, SERVICE OR

USE OF THIS FAN. FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN

SERIOUS PERSONAL INJURY AND / OR PROPERTY DAMAGE.

THIS IS A FAN - NOT A TOY!

TO REDUCE THE RISK OF

PERSONAL INJURY AND ELECTRIC SHOCK,

FANS SHOULD NOT BE PLAYED WITH OR

PLACED WHERE SMALL CHILDREN CAN

REACH IT.

WARNING

To guard against electric shock

while operating, do not allow fan

to come in contact with other grounded objects

such as pipes, radiators, etc.

WARNING

Risk of fire, electric shock, or

personal injury when performing

service or maintenance. Unplug or disconnect

the fan from the power supply before servicing.

WARNING

CAUTION Automatically

Operated Device - To Reduce

The Risk Of Injury Disconnect From Power

Source Before Servicing

WARNING

To Reduce The Risk Of Fire

Or Electric Shock, Do Not Use

This Fan With Any Solid- State Speed Control

Device.

WARNING

To Reduce The Risk Of Electric

Shock And Injury To Persons, Do

Not Use In a Window.

WARNING

To Reduce The Risk Of Electric

Shock, Do Not Expose To Water

Or Rain. This unit is designed for indoor use

only.

WARNING

Installation work and electrical

wiring must be done by

qualified person (s) in accordance with all

applicable codes and regulations.

WARNING

When servicing or replacing a

component requires the removal

or disconnection of a safety device, the safety

device is to be reinstalled or remounted as

previously installed before operating this fan.

WARNING

Use this fan only in the manner

intended by the manufacturer.

If you have any questions, contact Customer

Service at 800-641-6996.

WARNING

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

NOTES

__________________________________________________________________________________________

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Replacement Parts

Item # Description Part Number

1 Logo Plate 95-043-0370

2 Front Guard 95-032-0150

3

Fan Blade Assembly 95-003-06064

5

6 Upper Bracket 95-061-0100

7 Rear Guard 95-032-0250

8 Motor 95-030-0515

9 Switch Holder 95-031-0300

Item # Description Part Number

10 Switch Gasket 95-031-0340

11 Switch (Chain) 95-031-0110

12 Switch Cover 95-031-0500

13 Cord Bushing 95-026-0160

14 Pivot Washer 95-024-0300

15 Swivel Spacer 95-050-0185

16 Pivot Screw 95-024-0310

17 Capacitor 95-004-0215

18 Power Cord 95-026-0230

18” WALL FAN: PT-18W-DDF-A

1

2

3

4

5

6 7

8

9

10 11

12

13

14

15

16

17

18

Figure 1: Exploded View of PT-18W-DDF-A

Exploded View

Wall Mount Installation

1. Attach fan to wall or ceiling using Upper Bracket

(Item #6).

2. Be sure Upper Bracket (Item #6) is attached to a

suitable beam when hanging.

Tools Needed:

- 10mm Adjustable Wrench.

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4” stud, and that it

is able to support 50 pounds continuously.

WARNING

1. Attach wall mount to stud (Item #24*)

2. Attach Lower Support Frame (Item #21*) to the Wall

Mount (Item #24*) by replacing rear part of Lower

Support Frame into hook of Wall Mount and resting

front and rear feet of fan (Items #17* and #18*) onto

the wall.

* On Page 7

NOTE: Fan must be mounted to wall so that both feet

are positioned against the wall surface. Mounting

this fan to a bare stud without both fan feet posi-

tioned against a flat surface will result in damage

to the fan.

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

1. Remove 1 screw from each Frame Support L and R

(Items #7* and #19*).

2. Slide Frame Support L and Frame Support R into

Support Frame (Item #21*) and line up holes for screw.

3. Re-attach screw to Frame Support L and Frame

Support R.

4. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

Tools Needed:

- Phillips head screwdriver.

-10 mm adjustable wrench.

20” FLOOR FAN: PT-20F-DDF-A

Installation and Assembly

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4”

stud, and that it is able to support 50 pounds

continuously.

WARNING

20” FLOOR FAN - OPTIONAL WALL MOUNT

Wall Mount Installation

Figure 2: Wall Mount Installation

Figure 3: Wall Mount Installation - Close Up

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Replacement Parts

Item # Description Part Number

1 Logo Plate 95-043-0405

2 Front Guard 95-032-0160

3

Fan Blade Assembly 95-003-06164

5

6 Frame Washer 95-024-0250

7 Frame-Support L 95-024-0265

8 Main Circle Tube 95-024-0280

9 Top Washer 95-024-0290

10 Rear Guard 95-032-0260

11 Motor 95-030-0525

12 Switch Holder 95-031-0310

Item # Description Part Number

13 Switch 95-031-0120

14 Switch Cover 95-031-0510

15 Cord Bushing 95-026-0165

16 Control Knob 95-027-0110

17 Front Foot 95-023-0220

18 Rear Foot 95-023-0230

19 Frame-Support R 95-024-0275

20 Swivel Spacer 95-050-0180

21 Lower Support Frame 95-024-0245

22 Power Cord 95-026-0240

23 Capacitor 95-004-0225

24 Wall Mount Kit 95-078-0100

20” FLOOR FAN CONTINUED

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

23

22

17

18

19

20

21

24

Exploded View

Figure 4: Exploded View of PT-20F-DDF-A

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

20” SHOP FAN: PT-20S-DDF

Installation and Assembly

1. Remove Knob Screw (Item #15*) and Wing Nut (Item

#14*) from top of Post.

2. Slide Connector Bracket (Item #4*) onto top of post.

3. Line up holes on the Post and Connector Bracket

(Item #4*).

4. Re-insert the Knob Screw (Item #15) through the Post

and Connector Bracket (Item #14*) and tighten firmly

with the Wing Nut (Item #14*).

5. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

6. Set desired tripod stand height following “Tripod

Operation Instructions” below.

* On Page 10

Tripod Operation Instructions

TRIPOD LEG OPERATION

1. Fold legs out and slide support bracket to center of leg.

2. To adjust leg height; rotate locking ring clockwise to

loosen.

NOTE: Keep a firm grip on the tripod while leg is

unlocked! The leg will collapse into itself unless

held tightly.

NOTE: Be certain to make all three legs the same

height. Setting legs to different heights will make

the fan unbalanced and COULD FALL OVER.

3. Slide leg extension to desired height.

4. Rotate locking ring counter-clockwise and tighten firmly.

Be sure the leg is secure before moving to next leg.

5. Repeat steps 2-4 for remaining legs.

TRIPOD CENTER POST OPERATION

1. To change the post height; rotate locking ring

counter-clockwise to unlock post.

NOTE: Be certain to keep a firm grip on post while

unlocked! The fan will slide down to its lowest

point if it is not held and slowly moved to desired

position.

2. Raise or lower post to desired position.

3. Rotate locking ring clockwise to lock post and tighten

firmly.

DO NOT MOVE OR ADJUST

FAN WHILE IN OPERATION.

THIS CAN CAUSE DAMAGE TO FAN AND

INJURY TO THE OPERATOR.

WARNING

OPTIONAL CEILING MOUNT

1. Attach Ceiling Mounting Kit (Item #16*) to 2x4” stud

that is able to support 50 lbs continuously using

M6x40mm screw. (See Figure 5**)

3. Be Certain that the Safety Pin lines up with the groove

on the Connector Bracket (Item #4). (See Figure 6**)

2. Slide Connector Bracket (Item #4*) onto Ceiling

Mounting Post. (See Figure 7**)

4. Rotate the entire fan so the safety pin locks into place

and the holes on the Mounting Post line up with the

holes on the Connector Bracket (Item #4*). (See Figure

8**)

5. Insert the Knob Screw (Item #15*) through the

Mounting Post and Connector Bracket (Item #4*) and

tighten firmly with the Wing Nut (Item #14*).

(See Figure 8**)

* On Page 10

** On Page 9

Installation and Assembly

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4”

stud, and that it is able to support 50 pounds

continuously.

WARNING

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

20” SHOP FAN CONTINUED - OPTIONAL CEILING MOUNT

Figure 5:

Optional Ceiling Mount

Figure 8:

Optional Ceiling Mount

Figure 7:

Optional Ceiling Mount

Figure 6:

Optional Ceiling Mount

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

20” SHOP FAN CONTINUED

Exploded View

Replacement Parts

Item # Description Part Number

1 Logo Plate 95-043-0420

2 Front Guard 95-032-0185

3 Fan Blade Assembly 95-003-0616

4 Frame 95-001-0500

5 Rear Guard 95-032-0285

6 Motor 95-030-0525

7 Switch Holder 95-031-0335

8 Power Cord 95-026-0270

Item # Description Part Number

9 Power Switch 95-025-0600

10 Capacitor 95-004-0250

11 Bushing 95-026-0180

12 Switch Cover 95-031-0540

13 Tripod 95-040-0100

14 Wing Nut 95-075-0400

15 Base Knob 95-015-0220

16 Ceiling Mount Kit 95-078-0300

123

4

567 8 91011

121514

13

Figure 9: Exploded View of PT-20S-DDF

16

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

24” BARREL FAN: PT-24-DDF, PT-24-DDF-F

Installation and Assembly

1. Fully expand Pipe Frame (Item #20) open, and tighten

Frame Brackets (Items #21 and #22) with attached

bolt.

2. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

NOTE: This model CAN NOT be wall mounted.

Replacement Parts

Exploded View

Figure 10: Exploded View of

PT-24-DDF / PT-24-DDF-F

Item # Description Part Number

1 Logo Plate 95-043-0410

2 Front Guard 95-032-0170

3

Fan Blade Assembly 95-003-06214

5

6 Rubber Washer A 95-077-0100

7 Rubber Washer B 95-077-0110

8 Barrel 95-001-0300

9 Handle 95-006-0210

10 Rear Guard 95-032-0270

11 Motor 95-030-0530

12 Switch Holder 95-031-0320

Item # Description Part Number

13 Switch 95-031-0130

14 Cord Bushing 95-026-0170

15 Switch Cover 95-031-0520

16 Control Knob 95-027-0120

17 Power Cord 95-026-0250

18 Capacitor 95-004-0230

19 Foot 95-023-0210

20 Pipe Frame L/R 95-009-0500

21 Frame Bracket A 95-009-0510

22 Frame Bracket B 95-009-0520

23 Wheel Bolt 95-008-0310

24 Wheel 95-008-0110

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

24’’ OMNI DIRECTIONAL FAN: PT-24O-DDF

Replacement Parts

Item # Description Part Number

1 Front Guard 95-032-0170

2 Fan Barrel 95-001-0400

3 Power Knob 95-027-0130

4 Power Knob Holder 95-031-0325

5 Capacitor 95-004-0235

6 Power Cord 95-026-0255

7 Motor 95-030-0535

8 Motor Mount Assembly 95-030-0555

9 Motor Cooling Fan 95-030-0556

10 Fan Blade Assembly 95-003-0621

11 Rear Guard 95-032-0275

12 Front Leg 95-009-0600

13 Horizontal Adj. Knob 95-015-0150

14 Spacer 95-050-0200

15 Outer Ring Frame 95-024-0320

Item # Description Part Number

16 Vertical Adj. Knob 95-015-0150

17 Wall Mount 95-078-0200

18 Handle Pad 95-007-0100

19 Spacer 95-050-0200

20 Handle Arm 95-006-0300

21 Rear Leg 95-009-0610

22 Large Base Cap 95-024-0410

23 Large Base 95-024-0400

24 Foot Pad 95-023-0240

25 Wall Bracket - L 95-077-0100

26 Wall Bracket - R 95-077-0110

27 Small Base 95-024-0500

28 Small Base Cap 95-024-0510

29 Wheel 95-004-0155

30 Lower Mount 95-024-0325

31 Logo Plate 95-043-0331

Exploded View

1

2

3

4

5

7

8

9

10

11

12

13

14

16

19

17

18

21

20

22

23

25

26

27

Figure 11: Exploded View of: PT-24O-DDF

28

24

29

30

15

6

31

Installation and Assembly

1. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

24” OMNI FAN - OPTIONAL WALL MOUNT

1. Attach Wall Mount (Item #17*) to wood stud as shown

below.

2. Slide Wall Bracket L (Item #25*) and Wall Bracket

R (Item #26*) on Large Base (Item #23*) onto Wall

Mount.

* On Page 12

Tools Needed

-Flat head Screw Driver.

Wall Mount Installation

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4” stud, and that it

is able to support 105 pounds continuously.

WARNING

2”x4”

STUD

Wall

Wall Mount (Item #17*)

Handle Arm (Item #20*)

Wall Mount

(Item #17*)

Large Base

(Item #23*)

Figure 13: Wall Mount installation

Figure 12: Wall Mount installation Close Up

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

30” FLOOR FAN: PT-30-DDF

Replacement Parts

Item# Description Part Number

13 Wheel Axle 95-008-0260

14 Wheel Frame 95-008-0500

15 Upper Swivel Housing 95-050-0141

16 Frame Lower Swivel Latch 95-050-0150

17 Latch Spring 95-060-0155

18 Lower Swivel Housing 95-050-0161

19 Rear Guard 95-032-0240

20 Rear Swivel Bracket 95-050-0170

21 Capacitor 95-004-0200

22 Power Switch 95-025-0500

23 Rear Motor Cover 95-048-0100

24 Power Cord 95-026-0150

25 Guard Screw 95-033-0225

Item# Description Part Number

1 Front Guard 95-032-0140

2 Front Swivel Bracket 95-050-0100

3 Fan Blade Assy 95-003-0501

4 Motor 95-030-0500

5 Frame Foot 95-023-0200

6 Cart Frame 95-009-0400

7 Swivel Cover 95-050-0106

8 Frame Swivel Bracket 95-050-0111

9 Frame Upper Swivel Latch 95-050-0120

10 Swivel Latch Pin 95-050-0131

11 Frame Cap 95-011-0300

12 Wheel 95-008-0165

Installation and Assembly

1. Place the fan on level ground in a safe, desired position

then connect to an approved power source.

NOTE: This fan uses a folding wheel design. For quick

assembly, simply swing the wheels out and snap to

lock in place.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

Exploded View

23

25

24

25

Figure 14: Exploded View of PT-30-DDF

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

30” FLOOR FAN - OPTIONAL CEILING MOUNT

Ceiling Mount Installation

MOUNTING BRACKET INSTALLATION:

1. Remove Wheel Frame (Item #15)

2. Attach Cart Frame to Ceiling beam using U-bolts

(Item #5).

3. Assemble and attach Ceiling Mount Assembly as

shown in Figure 15 below.

Tools Needed

- Phillips and flat head screw driver.

- 10 mm adjustable wrench.

Item# Description Part Number

1 Safety Cable Assy 95-060-0100

2 Nut for Ceiling Swivel Pin 95-060-0180

3 Nut 95-060-0125

4 Upper Ceiling Bracket 95-060-0110

5 U-Bolt 95-060-0120

Ceiling Kit Replacement Parts

Item# Description Part Number

6 Top Washer 95-060-0120

7 Lower Ceiling Bracket 95-060-0160

8 Tapping Screw 5-15mm 95-060-0195

9 Ceiling Swivel Pin 95-060-0170

1

3

5

6

7

8

9

2

4

Figure 15: Exploded View of PT-30-DDF (ceiling mount kit)

Ceiling Kit Exploded View

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4” stud, and that it

is able to support 105 pounds continuously.

WARNING

This 30” Floor Fan (PT-30-DDF) is approved for use with

California’s BAR-97 Emissions Inspection System and meets

all BAR-97(EIS) required specications and standards

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

30” FLOOR FAN - OPTIONAL CEILING MOUNT CONTINUED

Ceiling Mount Installation

SAFETY CABLE INSTALLATION:

1. After the fan is securely mounted, feed the safety cable

between one of the swivel brackets as shown in Figure

15.

2. Pull safety cable through and secure cable with safety

cable U-bolt as shown in Figure 17.

3. Take other end of cable and wrap around beam

4. Secure cable loop as shown in step 2. Be sure there

is approximately 2 inches of slack in the safety cable

once both ends are secured.

5. Repeat on other side of fan so there are two safety

cables.

Tools Needed

- Phillips and flat head screw driver.

- 10 mm adjustable wrench

Figure 16: Safety Cable Installation

Figure 17: Safety Cable Installation - Close Up

The installer MUST be

certain that the support bracket is

mounted to a minimum of a 2x4” stud, and that it

is able to support 105 pounds continuously.

WARNING

Installation and Assembly

Tools Needed:

Pliers

Phillips head screwdriver

Flat head screwdriver

10mm / adjustable wrench

6mm hex wrench (included)

Parts Included In Box:

(1) Rubber Base Ring

(1) Base

(1) Front Guard

(1) Rear Guard

(1) Motor Assembly

(1) Fan Blade Assembly

(1) Spring

(1) Support Pole Assembly

1. Attach Rubber Base Ring (Item #16*) to outer edge of

Base (Item # 5*). Be sure ribbed side of Base Ring is

facing down.

2. Remove 5 screws from Flange on bottom of Lower

Support Pole (Item #13*).

3. Completely extend Upper Support Pole (Item #21*)

from Lower Support Pole and insert Spring into bottom

of Lower Support Pole.

4. Attach Support Pole Assembly to Base. Tighten

hardware using star pattern to insure a tight, uniform fit.

5. Stand assembly on Base, and press down Upper

Support Pole and then tighten Height Adjustment Knob

(Item #3*).

6. Attach Motor Support Assembly to Motor Assembly

(see Figure 18).

7. Place Motor Support into Upper Support Pole.

- Insert Pivot Bolt and tighten.

- Insert Tilt Adjustment Knob and tighten.

8. Remove 4 screws on motor, and attach the Rear Guard.

Tighten screws only after all 4 screws are reattached to

the motor.

9. Remove the screws on the Motor and attach the Rear

Guard onto groove in motor shaft, and replace screws

(See Figure 19).

10. Loosen the set screw on the back of the Fan Blade

Assembly and slide onto the motor shaft.

11. Position set screw over flat groove on motor shaft an

tighten set screw using 6mm hex wrench (included). Be

sure set screw is on the groove, and the front of Fan

Blade Assembly is flush with front of shaft before

tightening.

12. Attach Front Guard by first aligning the top hooks of

the Front Guard onto the top of the Rear Guard edge.

Work your way around the Guard, placing the Front

Guard hooks over the Rear Guard edge. If necessary,

use a flat head screwdriver to help pry the Front Guard

hooks over the Rear Guard edge. Continue until all

hooks are completely attached to the Rear Guard

edge.

NOTE: This model CAN NOT be wall mounted

* On Page 18

30” PEDESTAL FAN: PT-30P-DDF-A, PT-30P-DDF-AF

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Figure 19: Attaching Rear Guard to Motor

Rear Guard

Motor

Motor Assembly

Machine Screw

Pivot Bolt

Tilt

Adjustment

Knob

Motor Support

Assembly

Wing Nut

Nut

Upper Support Pole

Figure 18: Attaching Motor to Motor Support Assembly

Do NOT slide fan blade screw

beyond the groove on the shaft!

This will cause the fan blade to not spin properly

and can cause damage to your fan! Be sure that fan

shaft is flush with front of fan blade assembly.

CAUTION

30” PEDESTAL FAN

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

Item # Description Part Number

1 Logo Plate 95-043-0340

2 Front Guard 95-032-0181

3 Height Adjustment Knob 95-015-0205

4

Fan Blade Assembly 95-003-06315

6

7 Power Switch (Chain) 95-031-0140

8 Motor Assembly 95-030-0545

9 Rear Guard 95-032-0281

10 Height Adjust. Knob Nut 95-015-0215

11 Pipe Ring 95-017-0215

12 Pipe Support 95-017-0220

Item # Description Part Number

13 Lower Support Pole 95-017-0205

14 Latch Spring 95-060-0210

15 Upper Base 95-024-0225

16

Lower Base (Rubber

Base Ring)

95-024-0235

17 Motor Support 95-030-0560

18 Left Support 95-030-0570

19 Right Support 95-030-0575

20 Tilt Adjustment Knob 95-015-0210

21 Upper Support Pole 95-010-0305

22 Power Cord 95-026-0260

23 Capacitor 95-004-0240

Replacement Parts

Figure 20: Exploded View of

PT-30P-DDF-A / PT-30P-DDF-AF

1

2

12

4

5

6

7

9

8

3

10

11

13

14

16

17

19

22

21

15

20

18

23

Exploded View

Troubleshooting Guide

Problem Possible Cause Corrective Action

Fan does not operate

1. No power

Inspect power cord for damage. Be sure unit is

plugged in and turned on.

2. Bad motor Replace motor

Reduced Air Flow

1. Obstruction

Turn off and unplug fan. Remove guard and make sure

nothing is obstructing the fan blades.

2. Bad switch or capacitor

Replace switch or capacitor (Note: To prolong life of

fan, operate fan first in 1(LOW) for 5-10 seconds before

switching to higher speed.

Humming sound but no

operation

1. Bad capacitor Replace capacitor

Excess Noise (vibration,

squealing)

1. Fan is not on level ground Turn off fan, and move unit to smooth level surface.

2. Guard is not secure Check guard screws to be sure all are tight.

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

1 YEAR LIMITED WARRANTY

PINNACLE PRODUCTS INTERNATIONAL, INC. WARRANTS THIS

PRODUCT TO THE ORIGINAL RETAIL PURCHASER ONLY, TO BE

FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP FOR

A PERIOD OF ONE (1) YEAR FROM THE DATE OF INITIAL PUR-

CHASE. THIS PRODUCT MUST BE PROPERLY INSTALLED, MAIN-

TAINED AND OPERATED IN ACCORDANCE WITH THE INSTRUC-

TIONS PROVIDED.

PINNACLE PRODUCTS INTERNATIONAL, INC. REQUIRES REA-

SONABLE PROOF OF YOUR DATE OF PURCHASE FROM AN

AUTHORIZED RETAILER OR DISTRIBUTOR. THEREFORE, YOU

SHOULD KEEP YOUR SALES SLIP, INVOICE, OR

CANCELLED CHECK FROM THE ORIGINAL PURCHASE. THIS

LIMITED WARRANTY SHALL BE LIMITED TO THE REPAIR OR

REPLACEMENT OF PARTS, WHICH PROVE DEFECTIVE UNDER

NORMAL USE AND SERVICE WITHIN THE

WARRANTY PERIOD, AND WHICH PINNACLE PRODUCTS

INTERNATIONAL, INC. SHALL DETERMINE AT ITS

REASONABLE DISCRETION.

THIS WARRANTY DOES NOT APPLY TO PRODUCTS

PURCHASED FOR RENTAL USE.

THIS LIMITED WARRANTY DOES NOT COVER REPLACEMENT OF

BELTS OR TIGHTENING OF BELTS, OR ANY

FAILURES OR OPERATING DIFFICULTIES DUE TO NORMAL

WEAR AND TEAR, ACCIDENT, ABUSE, MISUSE, ALTERATION,

MISAPPLICATION, IMPROPER INSTALLATION OR IMPROPER

MAINTENANCE AND SERVICE BY YOU OR ANY THIRD PARTY.

FAILURE TO PERFORM NORMAL AND ROUTINE MAINTENANCE

ON THE FAN, SHIPPING DAMAGE, DAMAGE RELATED TO

INSECTS, BIRDS, OR ANIMALS OF ANY KIND, AND DAMAGE DUE

TO WEATHER CONDITIONS ARE ALSO NOT COVERED. IN ADDI-

TION, THE LIMITED WARRANTY DOES NOT COVER DAMAGE TO

THE FINISH, SUCH AS SCRATCHES, DENTS, DISCOLORATION,

RUST OR OTHER WEATHER DAMAGE, AFTER PURCHASE.

ALL TRANSPORTATION COSTS FOR THE RETURN OF THE DAM-

AGED PRODUCT OR PARTS WILL BE THE

RESPONSIBILITY OF THE PURCHASER. UPON RECEIPT OF DAM-

AGED ITEM, PINNACLE PRODUCTS INTERNATIONAL, INC. WILL

EXAMINE THE ITEM AND DETERMINE IF

DEFECTIVE.

PINNACLE PRODUCTS INTERNATIONAL, INC. WILL REPAIR

OR REPLACE AND RETURN THE ITEM, FREIGHT PRE-PAID. IF

PINNACLE PRODUCTS INTERNATIONAL, INC. FINDS THE ITEM

TO BE IN NORMAL OPERATING CONDITION, OR NOT DEFEC-

TIVE, THE ITEM WILL BE RETURNED FREIGHT

COLLECT.

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER EXPRESS

WARRANTIES. PINNACLE PRODUCTS INTERNATIONAL, INC.

DISCLAIMS ALL WARRANTIES FOR PRODUCTS THAT ARE PUR-

CHASED FROM SELLERS OTHER THAN AUTHORIZED RETAIL-

ERS OR DISTRIBUTORS.

AFTER THE PERIOD OF THE ONE (1) YEAR LIMITED

WARRANTY EXPIRES, PINNACLE PRODUCTS INTERNATIONAL,

INC. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

APPLICATION. FURTHER, PINNACLE PRODUCTS

INTERNATIONAL, INC. SHALL HAVE NO

LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY

FOR ANY SPECIAL, INDIRECT, PUNITIVE,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES. PINNACLE

PRODUCTS INTERNATIONAL, INC. ASSUMES NO

RESPONSIBILITY FOR ANY DEFECTS CAUSED BY THIRD PAR-

TIES. THIS LIMITED WARRANTY GIVES THE

PURCHASER SPECIFIC LEGAL RIGHTS; A PURCHASER MAY

HAVE OTHER RIGHTS DEPENDING UPON WHERE HE OR SHE

LIVES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMI-

TATION OF SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW LONG

A WARRANTY LASTS, SO THE ABOVE EXCLUSION AND LIMITA-

TIONS MAY NOT APPLY TO YOU.

PINNACLE PRODUCTS INTERNATIONAL, INC. DOES NOT

AUTHORIZE ANY PERSON OR COMPANY TO ASSUME FOR

IT ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION

WITH THE SALE, INSTALLATION, USE, REMOVAL, RETURN,

OR REPLACEMENT OF ITS EQUIPMENT, AND NO SUCH REP-

RESENTATIONS ARE BINDING ON PINNACLE PRODUCTS

INTERNATIONAL, INC.

ALWAYS BE SURE TO SPECIFY MODEL NUMBER AND SERIAL NUMBER WHEN MAKING ANY CLAIM

WITH PINNACLE PRODUCTS INTERNATIONAL, INC. FOR YOUR CONVENIENCE USE THE SPACE

PROVIDED BELOW TO LIST THIS INFORMATION:

Model #: ____________________ Serial #: ______________________

Date of Purchase: _________________

NEVER LEAVE A FAN

UNATTENDED WHILE

OPERATING OR WHILE

CONNECTED TO A POWER

SOURCE

668 Stony Hill Road #302 Yardley, PA 19067 USA Toll Free: (800) 641-6996

Fax: (215) 891-8461 • Web: www.protemp.us • Email: [email protected]

Register Online at: www.protemp.us/Product_Registration.php

ProTemp Protemp PT-20F-DDF-A User's Manual And Operating Instructions

This manual is also suitable for

ProTemp Protemp PT-20F-DDF-A User's Manual And Operating Instructions

Related papers

Other documents