Mitsubishi AF1200CFMR User manual

Mitsubishi
Brand
Mitsubishi
Model
AF1200CFMR
Category
Split-system air conditioners
Type
User manual

This manual is also suitable for

Air-Conditioners
INDOOR UNIT
PEFY-AF1200CFM, PEFY-AF1200CFMR
OPERATION MANUAL
For safe and correct use, please read this operation manual thoroughly before operating the air-conditioner unit.
MANUEL D’UTILISATION
Pour une utilisation correcte sans risques, veuillez lire le manuel d’utilisation en entier avant de vous servir du climatiseur.
English
Français
n_WT05632X01_h1_h4.p65 9/10/09, 10:13 AM3
1 Set Temperature button
2 Timer Menu button 3 Mode button
Monitor/Set button Back button
4 Timer On/Off button 5 Louver button
Set Day button Operation button
6 Fan Speed button 7 Vane Control button
8 Ventilation button
Operation button
9 Check/Clear button 0 Test Run button
A Filter button B ON/OFF button
button
C Location of built-in room temperature sensor D Set Time button
•Never expose the remote controller to direct sunlight. Doing so can result in
the erroneous measurement of room temperature.
•Never place obstacles around the lower right-hand section of the remote con-
troller. Doing so can result in the erroneous measurement of room tempera-
ture.
2
ON/OFF
FILTER
CHECK
CLEAR
MENU
ON/OFF
TEST
TEMP.
CLOCK
OPERATION
BACK DAY
MONITOR/SET
1
2
3
4D5689C
0
A
B
7
A Time/Timer time
B Centralized control indicator
C Timer OFF indicator
D Timer mode indicator
E Operation mode display:
COOL, DRY, AUTO,
FAN, HEAT
F Function mode indicator G Preset temperature
H Power indicator I Louver
J Ventilation K Filter
L Sensor position M Room temperature
N Vane setting O Fan speed
P Operation lamp
ON/OFF
ERROR CODE
TIME
ON
OFF
Hr
AFTER
SUN MON TUE WED THU FRI SAT
TIMER
AFTER
ONLY 1Hr.
˚C˚F
WEEKLY
SIMPLE
AUTO OFF
FILTER
FUNCTION
˚C˚F
TEMP.
E
B
C
H
IN MGPJD
L
A
O
F
K
1 Touche [Set Temperature] (Réglage de la température)
2
Touche [Timer Menu] (Menu de la minuterie)
3 Touche [Mode]
Touche [Monitor/Set] (Contrôle/réglage)
Touche [Back] (Retour en arrière)
4
Touche [Timer On/Off] (Minuterie Marche/Arrêt)
5 Touche [Louver] (Louvre)
Touche [Set Day] (Réglage du jour)
Touche [Operation] (Fonctionnement)
6
Touche [Fan Speed] (Vitesse du ventilateur)
7
Touche [Vane Control] (Commande des ailettes)
8 Touche [Ventilation]
Touche [Operation] (Fonctionnement)
9
Touche [Check/Clear] (Contrôler/effacer)
0 Touche [Test Run] (Essai de fonctionnement)
A Touche [Filter] (Filtre) B Touche [ON/OFF] (Marche/arrêt)
Touche [ ]
C Emplacement du capteur intégré de température de la pièce
D Touche de [réglage de l’heure]
• Ne jamais laisser la commande à distance en plein soleil sinon les données de
température ambiante risquent d’être erronées.
• Ne jamais placer d’obstacle devant la partie inférieure droite de la commande
à distance sinon la lecture des températures pourrait ne pas être correcte.
A Heure/heure de la minuterie
B Témoin de commande à distance centralisée
C Témoin de minuterie OFF
D Témoin de mode de minuterie
E
Affichage du mode de fonctionnement
: COOL, DRY, AUTO,
FAN, HEAT
(
FROID, DESHU, AUTO,
VENTILATION,
CHAUD)
F Témoin de mode de fonctionnement G Température prédéfinie
H Témoin d’alimentation I Louvre
J Ventilation K Filtre
L Position du capteur M Température de la pièce
N Réglage des ailettes O Vitesse du ventilateur
P Témoin de fonctionnement
Remote controller-Button
Touche Commande à distance
Remote controller-Display
Affichage Commande à distance
English
Français
English
Français
WT05632X01_p02.p65 09/9/17, 12:022
3
1. Safety precautions
s Before operating the unit, make sure you read all the “Safety
precautions”.
s “Safety precautions” lists important points about safety.
Please be sure to follow them.
Symbols used in the text
Warning:
Describes precautions that should be observed to avoid the risk of injury or
death to the user.
Caution:
Describes precautions that should be observed to prevent damage to the unit.
Symbols used in the illustrations
: Indicates an action that must be avoided.
: Indicates that important instructions must be followed.
: Indicates a part which must be grounded.
: Indicates that caution should be taken with rotating parts. (This symbol is
displayed on the main unit label.) <Color: yellow>
:Beware of electric shock. (This symbol is displayed on the main unit label.)
<Color: yellow>
Warning:
Carefully read the labels affixed to the main unit.
1.1. Installation
s After you have read this manual, keep it and the Installation Manual in a
safe place for easy reference whenever a question arises. If the unit is
going to be operated by another person, make sure that this manual is
given to him or her.
Warning:
• The unit should not be installed by the user. Ask the dealer or an author-
ized company to install the unit. If the unit is installed improperly, water
leakage, electric shock or fire may result.
• Use only accessories authorized by Mitsubishi Electric and ask your
dealer or an authorized company to install them. If accessories are in-
stalled improperly, water leakage, electric shock or fire may result.
• The Installation Manual details the suggested installation method. Any
structural alteration necessary for installation must comply with local
building code requirements.
•Never repair the unit or transfer it to another site by yourself. If repair is
performed improperly, water leakage, electric shock or fire may result. If
you need to have the unit repaired or moved, consult your dealer.
•Keep the electric parts away from water (washing water) etc.
• It might result in electric shock, catching fire or smoke.
Note1:
When washing the Heat Exchanger and Drain Pan, ensure the Con-
trol Box, Motor and LEV remain dry, using a water proof covering.
Note2: Never drain the washing water for the Drain Pan and the Heat
Exchanger using the Drain Pump. Drain separately.
• The appliance is not intended for use by young children or infirm per-
sons without supervision.
•Young children should be supervised to ensure that they do not play
with the appliance.
• Do not use a leak detection additive.
1) Outdoor unit
Warning:
• The outdoor unit must be installed on a stable, level surface, in a place
where there is no accumulation of snow, leaves or rubbish.
• Do not stand on, or place any items on the unit. You may fall down or the
item may fall, causing injury.
Caution:
The outdoor unit should be installed in a location where air and noise emit-
ted by the unit will not disturb the neighbours.
2) Indoor unit
Warning:
The indoor unit should be securely installed. If the unit is loosely mounted, it
may fall, causing injury.
3) Remote controller
Warning:
The remote controller should be installed in such a way that children cannot
play with it.
4) Drain hose
Caution:
Make sure that the drain hose is installed so that drainage can go ahead
smoothly. Incorrect installation may result in water leakage, causing dam-
age to furniture.
5) Power line, fuse or circuit breaker
Warning:
• Make sure that the unit is powered by a dedicated supply. Other appli-
ances connected to the same supply could cause an overload.
• Make sure that there is a main power switch.
• Be sure to adhere to the unit’s voltage and fuse or circuit breaker ratings.
Never use a piece of wire or a fuse with a higher rating than the one
specified.
6) Grounding
Caution:
• The unit must be properly grounded. Never connect the grounding wire
to a gas pipe, water pipe, lightning conductor or telephone grounding
wire. If the unit is not grounded properly, electric shock may result.
• Check frequently that the ground wire from the outdoor unit is properly
connected to both the unit’s ground terminal and the grounding electrode.
1.2. During operation
Caution:
• Do not use any sharp object to push the buttons, as this may damage the
remote controller.
• Do not twist or tug on the remote controller cord as this may damage the
remote controller and cause malfunction.
•Never remove the upper case of the remote controller. It is dangerous to
remove the upper case of the remote controller and touch the printed
circuit boards inside. Doing so can result in fire and failure.
•Never wipe the remote controller with benzene, thinner, chemical rags,
etc. Doing so can result in discoloration and failure. To remove heavy
stains, soak a cloth in neutral detergent mixed with water, wring it out
thoroughly, wipe the stains off, and wipe again with a dry cloth.
•Never block or cover the indoor or outdoor unit’s intakes or outlets. Tall
items of furniture underneath the indoor unit, or bulky items such as
large boxes placed close to the outdoor unit will reduce the unit’s effi-
ciency.
Warning:
• Do not splash water over the unit and do not touch the unit with wet
hands. An electric shock may result.
• Do not spray combustible gas close to the unit. Fire may result.
• Do not place a gas heater or any other open-flame appliance where it will
be exposed to the air discharged from the unit. Incomplete combustion
may result.
Contents
1. Safety precautions ...................................................................................... 3
1.1. Installation ................................................................................. 3
1.2. During operation ........................................................................ 3
1.3. Disposing of the unit .................................................................. 4
2. How to operate ........................................................................................... 4
2.1. ON/OFF ..................................................................................... 4
2.2. Return air temperature adjustment ........................................... 4
2.3. Ventilation .................................................................................. 4
2.4. Others ........................................................................................ 5
3. Maintenance ............................................................................................... 5
4. Troubleshooting ........................................................................................... 6
5. Installation, reinstalling, and maintenance .................................................. 7
6. Specifications .............................................................................................. 7
WT05632X01_en.p65 09/9/17, 15:533
4
Warning:
• Do not remove the front panel or the fan guard from the outdoor unit
when it is running. You could be injured if you touch rotating, hot or high-
voltage parts.
•Never insert fingers, sticks etc. into the intakes or outlets, otherwise in-
jury may result, since the fan inside the unit rotates at high speed. Exer-
cise particular care when children are present.
• If you detect odd smells, stop using the unit, turn off the power switch
and consult your dealer. Otherwise, a breakdown, electric shock or fire
may result.
• When you notice exceptionally abnormal noise or vibration, stop opera-
tion, turn off the power switch, and contact your dealer.
• Do not over-cool. The most suitable inside temperature is one that is
within 5 °C [41 °F] of the outside temperature.
• Do not leave handicapped people or infants sitting or standing in the path
of the airflow from the air-conditioner. This could cause health problems.
Caution:
• Do not direct the airflow at plants or caged pets.
•Ventilate the room frequently. If the unit is operated continuously in a
closed room for a long period of time, the air will become stale.
In case of failure
Warning:
•Never remodel the air conditioner. Consult your dealer for any repair or serv-
ice. Improper repair work can result in water leakage, electric shock, fire, etc.
• If the remote controller displays an error indication, the air conditioner
does not run, or there is any abnormality, stop operation and contact
your dealer. Leaving the unit as it is under such conditions can result in
fire or failure.
• If the power breaker is frequently activated, get in touch with your dealer.
Leaving it as it is can result in fire or failure.
• If the refrigeration gas blows out or leaks, stop the operation of the air
conditioner, thoroughly ventilate the room, and contact your dealer. Leav-
ing the unit as it is can result in accidents due to oxygen deficiency.
When the air conditioner is not to be used for a long
time
• If the air conditioner is not to be used for a long time due to a seasonal
change, etc., run it for 4 - 5 hours with the air blowing until the inside is
completely dry. Failing to do so can result in the growth of unhygienic,
unhealthy mold in scattered areas throughout the room.
• When it is not to be used for an extended time, keep the [power supply]
turned OFF.
If the power supply is kept on, several watts or several tens of watts will
be wasted. Also, the accumulation of dust, etc., can result in fire.
•Keep the power switched ON for more than 12 hours before starting op-
eration. Do not turn the power supply OFF during seasons of heavy use.
Doing so can result in failure.
1.3. Disposing of the unit
Warning:
When you need to dispose of the unit, consult your dealer. If pipes are re-
moved incorrectly, refrigerant (fluorocarbon gas) may blow out and come
into contact with your skin, causing injury. Releasing refrigerant into the
atmosphere also damages the environment.
2. How to operate
Before starting operation
• Operate after the “PLEASE WAIT” display has disappeared. The “PLEASE WAIT”
display briefly appears on the room temperature display (max. 3 minutes) when
the power is turned on and after a power failure. This does not indicate failure
of the air conditioner.
• Indoor unit operation mode is limited by the operation status of the connected
outdoor unit. If an outdoor unit and some of the connected indoor units are
already operating in the cooling mode, for example, only the cooling mode is
available for the rest of the units in the same group. If a different mode is re-
quested, the symbol that corresponds to the requested mode will blink, notify-
ing the user that the mode is currently unavailable. The same is true for the dry
and heating modes. This restriction, however, does not apply to the models
that support a simultaneous cooling/heating function.
• The outdoor units stop operating when all the connected indoor units stop
operating.
• During heating operation, even if the indoor unit is set to operation while the
outdoor unit is in defrost, operation starts after defrost of the outdoor unit has
ended.
2.1. ON/OFF
Start an operation
1. Press the B ON/OFF button
P Operation lamp lights up and operation starts.
Stop an operation
1. Press the B ON/OFF button again
Operation lamp goes off and operation stops.
• Once the buttons have been set, pressing the ON/OFF button only can repeat
the same operation thereafter.
• During operation, the operation lamp above the ON/OFF button lights up.
Caution:
Even if the ON/OFF button is pressed immediately after the operation is
once stopped, operation does not restart for about 3 minutes. This function
protects the machine. It automatically starts operation after 3 minutes has
lapsed.
2.2. Return air temperature adjustment
To change return air temperature
Press the 1 [Set Temperature] Button and set the return air temperature of
your choice.
Pressing
or
once changes the setting by 1 °C/1 °F.
If pressing continue, the setting continues to change by 1 °C [2 °F].
• Indoor temperature can be set within the following range.
PEFY-AF1200CFM :10 °C [50 °F] - 21 °C [70 °F]
PEFY-AF1200CFMR :17 °C [63 °F] - 28 °C [83 °F]
* The range of return air temperature display is 8 °C [46 °F] - 39 °C [102 °F].
Outside this range, the display flashes either 8 °C [46 °F] - 39 °C [102 °F] to
indicate if the return air temperature is lower or higher than the displayed tem-
perature.
2.3. Ventilation
• The ventilation unit (OA processing unit or LOSSNAY) automatically operation
when the indoor unit that is interlocked with operates.
• If the 8 Ventilation button is pressed while the indoor unit is stopped, only the
ventilator operates.
• Press the 8 Ventilation button to change the fan speed.
• Depending on the models, the indoor unit fan operates while the unit is in the
ventilation mode.
ON/OFF
CHECK
CLEAR
MENU
ON/OFF
TEST
TEMP.
CLOCK
OPERATION
BACK DAY
MONITOR/SET
1
E
2
8
B
P
7
FILTER
ERROR CODE
TIME
ON
OFF
Hr
AFTER
SUN MON TUE WED THU FRI SAT
TIMER
AFTER
ONLY 1Hr.
˚C˚F
WEEKLY
SIMPLE
AUTO OFF
FILTER
FUNCTION
˚C˚F
WT05632X01_en.p65 09/9/17, 15:534
5
3. Maintenance
Always have filters serviced by a qualified contractor.
Before maintenance, turn the power supply OFF.
Caution:
• Before start cleaning, stop operation and turn OFF the power supply.
Remember that the fan is rotating inside at high speed, posing a serious
risk of injury.
• Indoor units are equipped with filters to remove the dust of from the air.
Clean the filters following the procedures on the right. (The standard fil-
ter should normally be cleaned once a week, and the long-life filter at the
beginning of each season.)
• The life of the filter depends on where the unit is installed and how it is
operated.
How to clean
•Brush dust away lightly or clean it up with a vacuum cleaner. In the case of
severe staining, wash the filter in lukewarm water mixed with dissolved neutral
detergent or water, and then rinse off the detergent completely. After washing,
dry it and reattach it.
Caution:
• Do not dry the filter by exposing it to direct sunlight or warming it using
fire, etc. Doing so can damage the filter.
•Washing the filter in hot water (more than 50 °C [122 °F]) can also result
in damage.
Caution:
Never pour water or flammable sprays onto the air conditioner. Cleaning with
these methods can result in air conditioner failure, electric shock, or fire.
2.4. Others
: Displayed when control is executed by a separately
sold centralized control unit, etc.
STAND BY
DEFROST
: Displayed from the start up of heating operation until
the moment warm air blows out.
CHECK
: This display indicates if some abnormality is occur.
NOT AVAILABLE
: When a button is pressed for a function the indoor
unit cannot perform, this display flashes concurrently
with the display of that function.
FILTER
: Displayed when it is time to clean the filter.
Press the A Filter (
) button twice, then the display
disappear.
WT05632X01_en.p65 09/9/17, 15:535
6
4. Troubleshooting
Before you ask for repair service, check the following points:
Operation
It does not run.
Air flows out but it does
not cool enough or heat
enough.
Cool air or warm air
does not come out.
It runs briefly, but soon
stops.
The sound of the ex-
haust and rotation of
the motor can still be
heard after operation
stops.
The sound of the ex-
haust and the rotation
of the motor can be
heard intermittently af-
ter stop of running.
Warm air comes out in-
termittently when the
thermostat is OFF or
during fan operation.
Troubleshooting
Press the [ON/OFF] button after power restoration.
Turn the power supply ON.
Replace the fuse.
Install the ground breaker.
After checking the set temperature and inlet temperature
on the liquid crystal display, refer to Room temperature ad-
justment section.
Clean up the filter.
(Refer to Maintenance section.)
Remove.
Close.
Wait for a while.
(To protect the compressor, a 3-minute protection circuit is
built into the indoor unit. Therefore, there are occasions some-
times when the compressor does not start operating imme-
diately. There are cases when it does not run for as long as 3
minutes.)
Wait for a while.
(Heating operation starts after ending defrost ends.)
Rerun after removal.
Rerun after cleaning the filter. (Refer to [Caring for the ma-
chine].)
Wait for 3 minutes.
It soon stops. (If the noise occurs more than 2-3 times in an
hour, call a contractor for service.)
It soon stops. (If the room temperature rises uncomfortably
high in a small room, stop operation.)
Cause
Power failure
The power supply is turned OFF.
The fuse in the power supply is missing.
The ground breaker is missing.
Improper temperature adjustment.
The filter is filled with dust and dirt.
There are some obstacles at the air inlet and outlet of
the indoor and outdoor units.
Windows and doors are open.
The protect on circuit is in operation for 3 minutes.
Indoor unit operation was restarted during the heating
and defrosting operation.
There are some obstacles at the air inlet and outlet of
the indoor and outdoor units.
The filter is filled with dust and dirt.
If the other indoor units are in cooling operation, the
machine stops after operating a drain-lift mechanism
for 3 minutes when air-cooling operation is stopped.
If the other indoor units are in cooling operation, drained
water is brought in. If the drain water is collected, the
drain-lift mechanism initiates.
If the other indoor units are engaged in heating opera-
tion, the control valves are opened and closed from
time to time to maintain system stability.
Remote Controller
“'” display is not lit up.
No display appears even
when the [ON/OFF] but-
ton is pressed.
The liquid crystal display
shows that it is in the
state of operation.
The liquid crystal display
shows that it is in opera-
tion.
The “check” and check
code flashes on the liquid
crystal display.
All lights are out except
the powered display of
“'”.
All lights are out except
the powered display of
“'”.
The liquid crystal display
shows that it is in the
state of operation.
• If operation stops due to a power failure, the [protection circuit at power failure] operates and disables unit operation even after power is restored. In this case, press the
[ON/OFF] button again and start operation.
If malfunctions persist after the above, turn the power supply OFF and contact the dealer or contractor with information about the product name, the nature of the malfunction,
etc. If the display of “[check]” and (4 digit) check code flashes, tell the dealer or contractor contents of the display (check code). Never repair yourself.
The following symptoms are not air conditioner failures:
• The air blown out from the air conditioner can sometimes give off odors. This is due to cigarette smoke contained in the room air, the cosmetics smell, walls, furniture, etc.,
that is absorbed in the air conditioner.
•A hissing noise can be heard immediately after the air conditioner is started or stopped. This is the normal sound of the refrigeration flowing inside the air conditioner.
• The air conditioner sometimes snaps or clicks at the beginning or end of cooling/heating operation. This is the normal sound of friction on the front panel and other
sections due to expansion and contraction caused by temperature change.
WT05632X01_en.p65 09/9/17, 15:536
7
5. Installation, reinstalling, and maintenance
Installation area
Consult with your dealer for details on installation and transferring the installation.
Caution:
Never install the air conditioner where there is a risk of leakage of flammable
gas.
If gas leaks and accumulates around the unit, fire can result.
Never install the air conditioner at the following places:
• where there is a lot of machine oil
• direct exposure to the ocean and beach.
• where humidity is high
• where there are hot springs nearby
• where there is sulphuric gas
• where there is a high-frequency processing machinery (a high-frequency welder,
etc.)
• where acid solution is frequently used
• where special sprays are frequently used
• Install the indoor unit horizontally. Otherwise, water leakage can result.
•Take sufficient measures against electrical noise when installing the air condi-
tioners at hospitals or communication-related businesses.
If the air conditioner is used in any of the above-mentioned environments, frequent
operational failure can be expected. It is advisable to avoid these types of installa-
tion sites. For further details, consult with the dealer.
Regarding electrical work
Caution:
• The electrical work must be performed by a qualified contractor accord-
ing to the technical standard respecting electrical installation, internal
wiring rules, and the installation instruction manual with the absolute
use of exclusive circuits. The use of other products with the power source
can result in burnt-out breakers and fuses.
•Never connect the grounding wire to a gas pipe, water pipe, arrester, or
telephone grounding wire. For details, consult with the dealer.
• In some types of installation sites, the installation of an grand breaker is
mandatory. For details, consult with the dealer.
Regarding transfer of installation
• If removing and reinstalling the air conditioner, consult with the dealer in ad-
vance to ascertain the cost of the professional engineering work.
Caution:
When moving or reinstalling the air conditioner, consult with the dealer. De-
fective installation can result in electric shock, fire, etc.
Regarding sound
• In installing work, choose a place that can fully bear the weight of the air con-
ditioner, and where noise and vibration can be reduced.
• Choose a place where cool or warm air and sound from the outdoor air outlet
of the air conditioner does not inconvenience the neighbors.
• If any obstacles are placed near the outdoor air outlet of the air conditioner,
decreased performance and increased noise can result. Avoid placing any ob-
stacles adjacent to the air outlet.
• If the air conditioner produces any abnormal sound, consult with the dealer.
Maintenance and inspection
• If the air conditioner is used throughout several seasons, the internal compo-
nents can get dirty, reducing the performance.
Depending upon the conditions of usage, foul odors can be generated and
drainage can deteriorate due to dust and dirt, etc.
6. Specifications
Power source
Cooling capacity*1/Heating capacity*1 BTU/h
( ): Re-heat kW
Height mm [in.]
Dimension Width mm [in.]
Depth mm [in.]
Net weight kg [Ibs]
Airflow rate CFM
Fan
External static pressure*2
208V
230V
Noise level (Low-Middle-High)
*2
*3
208V
230V
Filter
PEFY-AF1200CFM
112,000/61,400
32.8/18.0
130 [287]
0.4 (99.6) -0.6 (149) -0.88 (219)
0.64 (159) -0.8 (199) -1.04 (259)
Item
Model
PEFY-AF1200CFMR
112,000/61,400 (24,200)
32.8/18.0 (7.1)
140 [309]
0.28 (70) -0.48 (120) -0.8 (200)
0.52 (130) -0.72 (180) -0.96 (240)
PEFY-AF1200CFM, PEFY-AF1200CFMR
208, 230V 60Hz
470 [18-9/16]
1385 [54-9/16]
1450 [57-1/8]
1200
41-43-46
44-46-48
Field Supplied
Notes: *1 Cooling/Heating capacity indicates the maximum value at operation under the following conditions:
Cooling: Indoor: 87 °F (30.5 °C) D.B./80 °F (26.7 °C) W.B. Outdoor: 87 °F (30.5 °C) D.B.
Heating: Indoor: 32 °F (0 °C) D.B. Outdoor: 32 °F (0 °C) D.B./27 °F (-2.6 °C) W.B.
Pipe length: 7.5 m (24-9/16 ft) Height difference: 0m (0 ft)
*2 The external static pressure is set to 0.88 in. WG (220 Pa) for PEFY-AF1200CFM or 0.8 in. WG (200 Pa) for PEFY-AF1200CFMR at factory shipment.
*3 The operating sound is the data that was obtained in an anechoic room.
WT05632X01_en.p65 09/9/17, 15:537
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
WT05632X01
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
Please be sure to put the contact address/telephone number on
this manual before handing it to the customer.
This product is designed and intended for use in the residential, commer-
cial and light-industrial environment.
n_WT05632X01_h1_h4.p65 9/10/09, 10:13 AM2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Mitsubishi AF1200CFMR User manual

Mitsubishi
Brand
Mitsubishi
Model
AF1200CFMR
Category
Split-system air conditioners
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents