Fine Art FINE700 User manual

Brand: Fine Art

Model: FINE700

Category: Stroboscopes & disco lights

Type: User manual

http:// en.fineart-light.com

- 1 -

Contents

Contents……………………………………………………………1

FINE700 Spot dimensions ………………………………………3

Brief Introduction………………………………………………4

Safety Information………………………………………………4

Transportation…………………………………………………6

Accessories …………………………………………………6

Transportation Lock………………………………………6

Lamp ………………………………………………………………7

Lamp Model: HTI 700W/D4/75 ……………………………7

Lamp replacement …………………………………………7

Operation of Lamp replacement…………………………7

Lamp adjustment……………………………………………8

AC Power ……………………………………………………………9

Fuse…………………………………………………………9

Power supply adjustment…………………………………9

Power connection …………………………………………9

Data ………………………………………………………………10

Data Connection……………………………………………10

DMX Data Connection………………………………………10

Installation …………………………………………………… 11

Install Fixtures on Truss ………………………………11

Control Panel ……………………………………………………13

DMX Address and protocol …………………………………13

Fine 700 Spot Gobo/ Color configuration …………………13

Animation Wheel …………………………………………13

Gobo Wheel …………………………………………………14

Color Wheel ………………………………………………16

Fine 700 Spot Specification …………………………………17

Dimmer and Strobe …………………………………………17

http:// en.fineart-light.com

- 2 -

CMY System…………………………………………………17

Static Color ………………………………………………17

Rotating gobos……………………………………………18

Static gobos ………………………………………………18

Gobo Animation ……………………………………………18

Iris …………………………………………………………18

Prism ………………………………………………………18

Focus & Zoom………………………………………………18

Pan/Tilt……………………………………………………18

Speed Control………………………………………………19

Controlling Channel …………………………………………19

DMX Channel………………………………………………21

Menu Control ………………………………………………30

Routine Maintenance ………………………………………36

Disassembly………………………………………………36

Cleaning ……………………………………………………40

Fine 700 Spot Channel Protocol………………………………42

http:// en.fineart-light.com

- 3 -

FINE 700 Spot dimensions

http:// en.fineart-light.com

- 4 -

Brief Introduciton

We appreciate you choose FINE700 Spot, and the features are as follows:

0-100% mechanical dimmer and strobe

CMY system

8 colors, including 2 CTC (color temperature correction) filters

6 rotating gobos and 9 static gobos

Changeable animation gobos

3-facet rotating prism

Iris

Focus and zoom

Pan 540°, tilt 246°

Electronic ballast

Safety information

Warning! This product is for professional application only, and it is not

for household use.

This product presents risks of lethal or severe injury due to fire

and heat, electric shock, ultraviolet radiation, lamp explosion, and falls.

Read this manual before powering or installing the fixture, follow the

safety precautions listed below and observe all warnings in this manual

and printed on the fixture. If you have questions about how to operate

the fixture safely, please contact your dealer.

Protection from blast

z Shields,lenses or ultraviolet screens shall be changed if they have

become visibly damaged to such an extent that their effectiveness is

impaired

z The lamp shall be changed if it has become damaged or thermally

deformed

Protection from Electric shock

z Cut off the power supply when remove or install lamp, fuse and other

spares; ensure the fixtures are grounded reliably.

http:// en.fineart-light.com

- 5 -

z Use a power supply comply with the fixtures, overload and creepage

protection are required.

z Don’t explore the fixture in rain or moist environment.

z Ask professional technician for maintenance.

Protection from UV radiation and lamp explosion

z Don’t use fixtures without or with broken lens, covers.

z Allow the fixture to cool for at least 30 minutes when opening

removing the lamp. Protect hands and eyes with gloves and safety

glasses.

z Don’t stare directly into the light or exposed lamp while it is lit.

z Replace the lamp before usage exceeds the maximum service life or

the lamp broken.

Protection from burns and fire

z Never attempt to bypass the thermostatic switch or fuses, and

remember to replace defective fuses with the specified type and rating.

z Keep combustible materials (such as fabric, wood, paper) at least

0.5meter away from the fixture.

z Do not illuminate surfaces within 1.2 meters of the fixture.

z Keep at least 0.1 meters around fans and air vents.

z Don’t place filters or other materials over the lens

z Cool off the fixture at lease 30 minutes before removing it.

z Use the spares which are from FINE ART.

z Don’t operate the fixture when the ambient temperature exceed 40 ℃.

Protection from injury when fixture falls

z Don’t remove the fixture alone

z When suspending the fixture, ensure that the structure can hold at least

10 times the weight of all installed devices.

z Make sure that all covers and rigging hardware are securely fastened

and use an approved means of secondary attachment such as a safety

cable.

http:// en.fineart-light.com

- 6 -

z During installation or remove fixtures, keep in mind that the working

flat roof is lower than the working position.

Transportation

Note! Unlock the tilt lock when operate the fixture.

Accessories

This Fine700 Spot is pack in flight case or carton, 1 or 2 PCS/CTN, each

fixture is equipped with accessories as follows:

Users’ Manual

2 clamps

Guarantee card

1 safety cable

1 Data cable

Transportation Lock

Fixtures are locked during the transportation, the position of lock is showed

in the picture, unlock it before operating the fixture.

Picture 1

http:// en.fineart-light.com

- 7 -

Lamp

Lamp model: HTI 700W/D4/75

Fine700 Spot use OSRAM HTI 700 W/D4/75 discharge lamp, as this

efficient short-arc source with a color temperature of 7380 K, a color

rendering index of 75, an average service life of 750 hours and hot restrike.

Warning! Install other lamps will creates safety hazard or damage the

fixture.

The average service life of this lamp is 750 hours, in order to reduce

the risk of fixture, please replace the lamp before the usage exceed 125% of

the service life.

Lamp replacement

Note! Don’t touch the bulb with bare hands, so oils won’t touch the

bulb, keep the bulb clean. Clean lamp with alcohol, and polish it with dry

cloth.

Operation of Lamp replacement

1. Cut off the power supply, cool off it at least 30 minutes, place the body

at 15, and lock the body.

2. See picture 2, open the cover, loose the screws as the arrow showed,

pull the lamp assembly straight back as far as it goes and let it rest in

place.

Picture 2

3. See picture 3, To disassembly the lamp, loose the poles of the lamp with

a screwdriver from the socket, then pull out two poles one by one

respectively.

Picture 3

http:// en.fineart-light.com

- 8 -

4. See picture 4, To install the lamp, Aim two poles of the lamp to the

matched socket in advance (Ensure the direction of lamp’s nipple

toward the socket), then push two poles into the socket synchronously.

Picture4

5. Lift the lamp assembly so that lamp is level with the center of the

reflector. Push the assembly straight in until it seats, making sure the

lamp passes

Note: Push and pull the lamp assembly along with the slider bar, don’t touch

hardware that locate around the reflector, in case the lamp broken.

To align the lamp

1. Apply power and allow the fixture to reset. Using a controller or the

control menu, strike the lamp and project an open white beam on a flat

surface.

2. See Figure 5. Center the hot spot vertically using the top Allen-head

adjustment screw (A) in the center of the rear plate. Center the hot spot

horizontally using the side-to-side adjustment screws (B).

3. If there is an excessive hot spot, turn the bottom adjustment screw (B)

counterclockwise until the light is evenly distributed. If the light is

brighter around the edge than it is in the center, or if light output is low,

turn the bottom adjustment screw (B) clockwise until the light is bright

and evenly distributed.

4. Repeat Step 2.

http:// en.fineart-light.com

- 9 -

Picture 5

AC Power

Warning! For protection from electric shock, the fixture must be grounded

(earthed). The AC mains supply must be fitted with a fuse or

circuit breaker and ground-fault (earth-fault) protection.

Important! Please check the power supply before applying power.

Fuse

FINE700 Spot has two kinds of fuse:

z 15 AT fuse for use with AC supplies of 100 - 130 volts

z 10AT fuse (installed) for use with AC supplies of 200 - 250 volts

Power supply adjustment

Voltage range: 90-260V, which can be shift by 110-220V alternation

switch.

Power Connection

Notice! Connect the FINE 700 Spot directly to AC power. Do not connect it

to a dimmer system; doing so may damage the fixture. We have

equipped with standard 3 pin connector, please connect the power

according to the marks below, yellow/green wires grounded stable,

if you have any other questions, please consult qualified technician.

http:// en.fineart-light.com

- 10 -

To apply power, set the power switch on the base to the “I” position.

Wire Color Connector Marks

Brown Live wire L

Blue Neutral wire N

Yellow/Green Ground wore

Data

Important! Never connect more than 1 data input and 1 data output.

FINE700 Spot has both 3-pin and 5-pin XLR sockets for DMX input and

output. The pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin

3 to hot (+).

Connection equipment

z Use shielded twisted-pair cable designed for DMX512 devices:

standard microphone cable cannot transmit control data reliably over

long runs. 24 AWG cable is suitable for runs up to 300 meters.

Heavier gauge cable and/or a DMX512 signal amplifier is

recommended for longer runs.

z Never use both outputs to split the link. To split the serial link into

branches use a splitter.

z Do not overload the link. At most 32 devices may be connected on a

serial link.

z Terminate the link by installing a termination plug in the output

socket of the last fixture. The termination plug, which is a male XLR

plug with a 120 Ohm, 0.25 Watt resistor soldered between pins 2 and

3, soaks up the control signal so it does not reflect and cause

interference. If a splitter is used, terminate each branch of the link.

Data Link

1、 Connect the DMX data output from the controller to FINE700

Spot’s 3-pin or 5-pin input (male) socket.

http:// en.fineart-light.com

- 11 -

2、 Using the sockets that match your data cable, connect the output of

the fixture closest to the controller to the input of the next fixture.

3、 Insert a male 120 Ohm XLR termination plug in the 3-pin or 5-pin

output of the last fixture on the link.

Installation

FINE700 Spot can be placed on stage or clamped to a truss in any

orientation. The mounting points allow the clamp brackets to be fastened

parallel or perpendicular to the front as shown Figure 6.

Picture 6

Warning!

Always use 2 clamps to rig the fixture. Lock each clamp with both

1/4-turn fasteners. The fasteners are locked only when turned fully

clockwise. Attach an approved safety cable to the attachment point labelled

“SAFETY WIRE” in the base. Never use the carrying handles for secondary

attachment.

Clamp the fixture on a truss

1、 Check that the rigging clamps are undamaged and can bear at least

10 times the weight of the fixture. Check that the structure can

bear at least 10 times the weight of all installed fixtures, clamps,

cables, auxiliary equipment, etc.

http:// en.fineart-light.com

- 12 -

2、 Bolt each clamp securely to a clamp bracket with an M12 bolt and

lock nut.

3、 Align a clamp with 2 mounting points in the base. Insert the

fasteners into the base and turn both levers a full 1/4-turn

clockwise to lock. Install the second clamp.

4、 If the truss can be low, fixture can be clamp directly from the flight

case. Block access under the work area. Working from a stable

platform, hang the fixture on the truss with the arrow towards the

area to be illuminated. Tighten the rigging clamps.

5、 Install a safety wire that can bear at least 10 times the weight of

the fixture. The attachment point is designed to fit a carabiner

clamp.

6、 Check that the tilt lock is released. Verify that there are no

combustible materials or surfaces to be illuminated within 1.2

meters (42 inches) of the fixture, and that there are no flammable

materials nearby.

Picture 7 Picture 8

http:// en.fineart-light.com

- 13 -

Control panel

LCD control panel used for set address and fixture functions.

DMX Address set up

The DMX address, also known as the start channel, is the first channel

used to receive instructions from the controller. For independent control,

each fixture must be assigned its own control channels. Address sharing can

be useful for diagnostic purposes and symmetric control, particularly when

combined with the inverse pan and tilt options.

Two control mode: 23 channels and 31 channels.

FINE700 Spot color/gobo structure

Animation wheel

FINE700 Spot is equipped with 191160001 gobo, and there are other gobos

for choose.

Pic9 P/N:191160001 191160002 191160003 191160004

Animation wheel replacement

The replacement animation wheel can be inserted with the magnet in or

out to suit your application. In fixed applications, install the wheel with the

magnet forwards, away from the drive mechanism, for easier removal. In

touring or similar applications where the fixture is frequently moved, install

the animation wheel with the magnet in towards the drive mechanism for a

more secure hold.

① Remove the gobo module as described on page 31(Routine maintenance:

Disassembly).

http:// en.fineart-light.com

- 14 -

② Bring the animation wheel to the side of the module closest to you by

turning the black belt on the right as show in page 32.

③ To avoid bending the animation wheel while removing, break the

magnets initial hold by prying the wheel off with a screwdriver inserted

from the back. Once you have broken the hold, you can safely grasp the

wheel by the edge and remove.

④ Orient the replacement wheel with the magnet in or out to suit your

application (see note above this list). Place the wheel over the drive

mechanism and align the hole in the wheel with the drive pin.

⑤ Reinstall the gobo module. Verify that the guide pins are correctly seated

and that the module is securely locked.

Gobo wheel

Gobo wheel 1 provides 6 rotating gobos; gobo wheel 2 provides 9 static

gobos.

The standard gobo configuration is shown in Figure 10, and other gobos can

be replaced according to customers’ requirements.

Picture 10

Customization

To optimize effect, all gobos should be:

Outside diameter：---------------------∅27.9 +0/-0.2mm（1.1 +0/-0.01 in）

Maximum gobo diameter：-----------23mm（0.9 in）

http:// en.fineart-light.com

- 15 -

Material: High temperature resistant glass and 0.5mm high temperature

resistant aluminum alloy.

On wheel 1, the gobo retention spring works with gobos up to 3 mm in

thickness. Thicker gobos can be glued to the holder.

Aluminum gobo with low cost and perfect effect, the useful life will depend

on the gobo pattern and the projection cycle.

Gobos are interchangeable between FINE400 Spot and FINE700 Spot.

Orientation

Coated Glass Gobos Coating side(more

effective side)

towards lamp

non-coating side back

against the lamp

Textured Glass Gobos Textured side towards

lamp

smooth side back

against the lamp

Metal gobos More effective side

towards lamp

black side back against

the lamp

Image/text gobos True image towards

lamp

reversed image towards

lamp

Replacement of rotating gobo wheel

1、 rasp the holder by the teeth and pull the holder lightly towards the front

lens to release the holder and remove it from the wheel.

2、 Unhook the end of the gobo spring furthest from the gobo and pull out

the spring. Drop the gobo out of the holder.

3、 Insert the new gobo in the holder, insert the spring with the narrow end

against the gobo, and push the end of the spring in under the lip of the

holder.

4、 Work the rim of the gobo holder under both clips and snap the gobo

holder back into position on the gobo wheel. If necessary, a small

screwdriver or similar tool may be used to pry the clips away from the

wheel.

http:// en.fineart-light.com

- 16 -

Picture11

Replace static gobos

1、 Turn the gobo wheel to the desired position. Press the gobo from the

lamp side to release. Remove the gobo.

2、 To insert a gobo, orient the gobo and place the edges under the retention

spring.

Color Wheel

FINE700 Spot has 1 color wheel with 8 changeable dichroic color

filters, as shown in picture 12.

Picture 12 Color wheel (view from prism side)

Replace color filters

Notice! Wear cotton gloves while handling color filters and coating side

towards to the lamp.

1、 Turn the color wheel to access the desired filter position for easy

disassembly.

2、 Press the filter forwards slightly to release it and then grasp it by the

edges and remove. If your fingers are too large, protect the glass with a

piece of paper that has been folded several times and grasp the filter

with needle nose pliers.

http:// en.fineart-light.com

- 17 -

Picture 13

3、 Slide it under the retention spring until it snaps into place to insert a

new color filter.

FINE700 Spot functions

Dimming, strobe and power adjustment

The mechanical dimmer/shutter system provides smooth, high-resolution

100 percent dimming, instant open and blackout, random and variable

strobe effects up to 10 Hz, and random and variable pulses in which the

dimmer snaps open and slowly dims or snaps closed and slowly opens.

Output power can be adjusted from 50%-100%.

CMY system

CMY system adopts continuous dichroic Cyan, magenta and yellow

color filters. It is a kind of color fading system, moving colors form

white light, 3 kinds of color filters superpose completely create

blinding, and two kinds of color filters mix create another color.

Static color

There are 8 positions for 8 PCS color filters on the color wheel, and

it can rotate random with different speed as well as continuous

rotating.

http:// en.fineart-light.com

- 18 -

Rotating gobos

There are 6 gobos on the rotating gobo wheel.

Gobos can rotate with different speed or index in a position, and with

16 bit fine resolution. Gobos can be selected, indexed (positioned at a

programmed angle), rotated continuously, and shaken (bounced). The gobo

wheel can also be scrolled continuously. Gobo position and rotating speed

can be controlled through position/speed channel, and fine orientation of

gobo position can be adjusted further through 16bit fine channel.

Static gobo

Static gobo wheel has 9 gobos can rotating with different speed and

rotate continuous.

Animation wheel

Animation wheel can create animation effect such as rising flame and

rolling water.

Iris

Offer freely pulse iris effect with different speed.

Prism

The fixture is equipped with 3 facet changeable prism, and the prism

can rotate clockwise and anti-clockwise with different speed.

Focus and zoom

The focus lens focuses the beam from approximately 2 meters (6.5 feet)

to infinity. The separate zoom lens varies the focused beam angle from 14°

to 30°.

Pan and tilt

Pan 540°, tilt 246°, and if fine orientation required, please choose

16bit channel.

Pan/tilt speed (fast, normal, slow) and effects speed channels

http:// en.fineart-light.com

- 19 -

Speed control

The controllable speed from static situation to rotation of the fixture:

the speed can be controlled by pan/tilt speed and effect speed channels, all

of which can operate separately.

Tracking mode to open the iris, for example, you program a scene with

the iris fully closed and a second scene with the iris fully open. If you set a

cross-fade time between the two scenes, to say 10 seconds, the controller

gradually changes the iris position value from 199 (closed) to 0 (open).

Controlling Channels

Controlling mode: 23 channels mode and 31 channels mode

23 controlling channels

Channel 1: Shutter, strobe, reset, lamp on/off

Channel 2: Dimmer

Channel 3: CMY Cyan

Channel 4: CMY Magenta

Channel 5: CMY Yellow

Channel 6: Color wheel

Channel 7: Gobo I

Channel 8: Gobo I, gobo orientation and rotation

Channel 9: Gobo I 16bit

Channel 10: Gobo II

Channel 11: Gobo/color Macro function

Channel 12: animation wheel

Channel 13: animation wheel angle/speed

Channel: Prism

Channel 15: Iris

Channel 16: Focus

Channel 17: Zoom

Channel 18: Pan

Channel 20: Tilt

http:// en.fineart-light.com

- 20 -

Channel 21: Tilt Fine 16bit

Channel 22: Pan&Tilt Speed

Channel 23: Effect Speed

31 controlling channels:

Channel 1: Shutter, strobe, reset, lamp on/off

Channel 2: Dimmer

Channel 3: Dimmer 16bit

Channel 4: CMY Cyan

Channel 5: CMY Cyan 16bit

Channel 6: CMY Magenta

Channel 7: CMY Magenta 16bit

Channel 8: CMY Yellow

Channel 9: CMY Yellow 16 bit

Channel 10: Color wheel

Channel 11: Color wheel 16bit

Channel 12: Gobo I

Channel 13: Gobo wheel I, gobo orientation and rotation

Channel 14: Gobo wheel I 16bit

Channel 15: Gobo wheel II 16bit

Channel 16: Gobo&color Macro function

Channel 17: Animation gobo

Channel 18: Animation gobo, angle/speed

Channel 19: Prism

Channel 20: Iris

Channel 21: Iris 16bit

Channel 22: Focus

Channel 23: Focus 16bit

Channel 24: Zoom

Channel 25: Zoom 16bit

Channel 26: Pan

Channel 27: Pan Fine 16bit

Channel 28: Tilt

http:// en.fineart-light.com

- 21 -

Channel 29: Pan Fine 16bit

Channel 30: Pan&tilt speed

Channel 31: Effect Speed

DMX Channels

Starting code: 0

Channels

Value Percent Function

1 1

0-19

20-49

50-72

73-79

80-99

100-119

120-127

128-147

148-167

168-187

188-190

191-193

194-196

197-199

200-202

203-207

208-217

218-227

228-237

238-247

248-255

0-7

8-19

20-28

29-31

31-39

39-47

47-50

50-58

58-65

66-73

74-75

75-76

76-77

77-78

78-79

80-81

82-85

85-89

89-93

93-97

97-100

Shutter, strobe, reset, lamp on/off

Shutter closed

Shutter open

strobe, fast→slow

Shutter open

Opening strobe pulse, fast → slow

Closing strobe pulse, fast → slow

Shutter open

Random strobe, fast

Random strobe, medium

Random strobe, slow

Shutter open

Random opening pulse, fast

Random opening pulse, slow

Random closing pulse, fast

Random closing pulse, slow

Shutter open

Reset fixture

Shutter open

Lamp on

Shutter open

lamp off

2 2 0-255 0-100 Dimmer 0%-100%

http:// en.fineart-light.com

- 22 -

3 - 0-255 0-100 Dimmer 16bit

4 3

0-255

1-127

128-254

255

0-100

1-50

50-99

100

Cyan

white→cyan

CMY combination(set normal

11 controlling channels or

extend 16 controlling channels)

Normal mode

At least 0-100%

At most 0-100%

Normal mode

5 - 0-255 0-100 Cyan 16bit

6 4

0-255

1-127

128-254

255

0-100

1-50

50-99

100

Magenta

white → magenta

CMY combination(set normal

11 controlling channels or

extend 16 controlling channels)

Normal mode

At least 0-100%

At most 0-100%

Normal mode

7 - 0-255 0-100 Magenta 16bit

8 5

0-255

0-100

Yellow

white→yellow

CMY combination(set normal

11 controlling channels or

extend 16 controlling channels)

8 5

1-127

128-254

255

1-50

50-99

100

Normal mode

At least 0-100%

At most 0-100%

Normal mode

http:// en.fineart-light.com

- 23 -

9 - 0-255 0-100 Yellow 16bit

10 6

0-17

17-34

34-51

51-68

68-85

85-102

102-119

119-136

136-153

154-158

159-163

164-168

169-173

174-178

179-183

184-188

189-193

194-198

0-7

7-13

13-20

20-27

27-33

33-40

40-47

47-53

53-60

60-62

62-64

64-66

66-68

68-70

70-72

72-74

74-76

76-78

color wheel

smooth change of colors

white→color 1

color1→2

color2→3

color3→4

color4→5

color5→6

color6→7

color7→8

color8→white

stepping change of colors

color8 CTC3200-4100

color7 CTC4200-5500

color 6 half green

603 color 5 yellow 603

color 4 magenta 301

color 3 pink 312

color 2 blue 102

color 1 green 208

open

10 6

199-219

220-240

241-245

246-250

251-255

78-86

86-94

95-96

96-98

98-100

continuous rotation of colors

clockwise fast→slow

anticlockwise slow→fast

random position and color

fast

medium

slow

11 - 0-255 0-100 color wheel 16bit

http:// en.fineart-light.com

- 24 -

12 7

0-11

12-15

16-19

20-23

24-27

28-31

32-35

36-39

40-43

44-47

48-51

52-55

56-59

60-71

72-83

84-95

96-107

0-4

4-5

6-7

7-9

9-10

11-12

12-13

14-15

15-16

17-18

18-20

20-21

22-23

23-27

28-32

33-37

37-42

Gobo wheel I,gobos and function

selecting static gobos

open

gobo 1

gobo 2

gobo 3

gobo 4

gobo 5

gobo 6

selecting rotatable gobos

gobo 1

gobo 2

gobo 3

gobo 4

gobo 5

gobo 6

selecting dithering gobos

gobo1,dithering,slow→fast

gobo2,dithering,slow→fast

gobo3,dithering,slow→fast

gobo4,dithering,slow→fast

http:// en.fineart-light.com

- 25 -

12 7

108-119

120-131

132-143

144-155

156-167

168-179

180-191

192-203

204-229

230-255

42-46

47-51

52-56

56-61

61-65

66-70

70-75

70-79

80-90

90-100

gobo5,dithering,slow→fast

gobo6,dithering,slow→fast

selecting dithering gobos

gobo1,dithering,slow→fast

gobo2,dithering,slow→fast

gobo3,dithering,slow→fast

gobo4,dithering,slow→fast

gobo5,dithering,slow→fast

gobo6,dithering,slow→fast

gobo wheel rotation

clockwise, slow→fast

anticlockwise, fast→slow

13 8

0-255

0-2

3-127

128-252

253-255

0-100

1-50

51-99

100

gobo wheel I

If static gobo is chosen

angle orientation 0-360°

If rotatable gobo is chosen

No rotation

clockwise, slow→fast

anticlockwise, fast→slow

No rotation

14 9 0-255 0-100 Gobo wheel I 16bit

15 10

0-11

11-22

22-33

33-44

44-55

55-66

66-77

0-4

4-8

8-13

13-17

17-21

21-26

26-30

gobo wheel II

smooth change of colors

white→gobo1

gobo1→2

gobo2→3

gobo3→4

gobo4→5

gobo5→6

gobo6→7

http:// en.fineart-light.com

- 26 -

15 10

77-88

88-99

99-110

110-112

113-121

122-130

131-139

140-148

149-157

158-166

167-175

176-184

185-193

194-202

203-221

222-240

241-245

246-250

251-255

30-34

34-39

39-43

43-44

44-47

48-51

51-54

55-58

58-61

62-65

65-68

68-72

72-76

76-79

79-87

87-94

95-96

96-98

98-100

gobo7→8

gobo8→9

gobo9→white

white

stepping change of colors

gobo 9

gobo 8

gobo 7

gobo 6

gobo 5

gobo 4

gobo 3

gobo 2

gobo 1

open

continuous rotation of gobos

clockwise, fast→slow

anticlockwise, slow→fast

ndom position and gobo

fast

medium

slow

16 11

0-15

16-55

56-95

0-5

6-21

22-37

gobo/color Macro function

gobo wheel II and color wheel

without Macro function

gobo wheel II dithering,

slow →fast

color wheel, dithering,

slow →fast

http:// en.fineart-light.com

- 27 -

16 11

96-135

136-175

176-215

216-255

37-53

53-68

69-84

85-100

gobo wheel II and color wheel

dithering, slow →fast

random CMY mixed color(basic

channel3、4、5 are set as “at

least” and extended channel4、

5、6 are set as “at most”)

fast

medium

slow

17 12

0-9

10-19

20-29

30-39

40-49

50-139

140-229

230-255

0-3

4-7

8-11

12-15

16-19

20-54

55-89

90-100

animation gobos

open

Tilt default position

Pan default position

Tilt continuous rotation

Pan continuous rotation

angle default position, tilt→pan

angle continuous rotation, tilt→pan

open

18 13

0-255

0-2

3-127

128-252

253-255

0-100

0-1

1-50

51-99

99-100

animation gobo, angle and speed

if default position is chosen

rotation angle, min→max

if continuous rotation

is chosen

no rotation

anticlockwise, slow→fast

clockwise, fast→slow

no rotation

http:// en.fineart-light.com

- 28 -

19 14

0-19

20-79

80-89

90-149

150-215

216-220

221-225

226-230

231-235

236-240

241-245

246-250

251-255

0-7

8-31

31-35

35-58

59-84

85-86

87-88

89-90

91-92

93-94

95-96

96-98

98-100

prismrotation

prism open

prism insert, anticlockwise, fast→slow

prism insert, no rotation

rism insert, clockwise, slow→fast

prism open

prism Macro function

Macro function 1

Macro function 2

Macro function 3

Macro function 4

Macro function 5

Macro function 6

Macro function 7

Macro function 8

20 15

0-199

200-215

216-229

230-243

244-246

247-249

250-252

253-255

0-78

78-84

85-90

90-95

96-96

97-98

98-99

99-100

Iris

open→shut

shut

opening pulse, fast→slow

closing pulse, fast→slow

random opening pulse,fast

random opening pulse,slow

random closing pulse,fast

random closing pulse,slow

21 - 0-255 0-100 iris 16bit

22 16

0-255

0-100

focus

infinity→2m, 0-100 linear

adjustment

23 - 0-255 0-100 Focus 16bit

http:// en.fineart-light.com

- 29 -

24 17

0-255

0-100

Zoom

0-100 linear adjustment

25 - 0-255 0-100 Zoom 16bit

26 18 0-255 0-100 pan 8bit

27 19 0-255 0-100 pan 16bit

28 20 0-255 0-100 tilt 8bit

29 21 0-255 0-100 tilt 16bit

30 22

0-2

3-242

243-245

246-248

249-251

252-255

0-1

1-95

95-96

96-97

98-98

99-100

pan/tilt speed control

tracking mode

fast→slow

slow

medium

fast

color switch during the movement

31 23

0-2

3-245

246-251

252-255

0-2

3-245

246-248

249-251

252-255

0-1

1-96

96-98

99-100

0-1

1-96

96-97

98-98

99-100

Effect speed

dimmer,animation wheel,focus and zoom

tracking mode

fast→slow

tracking mode

fastest

color speed

tracking mode

fast→slow

non-shortest circuit, tracking mode

shortest circuit, tracking mode

color switch during the movement

http:// en.fineart-light.com

- 30 -

31 23

0-245

246-248

249-251

252-255

0-2

3-245

246-251

252-255

0-251

252-245

0-96

96-97

98-98

99-100

0-1

1-96

96-98

99-100

0-98

99-100

gobo speed

moderate speed

non-shortest circuit, tracking mode

shortest circuit, tracking mode

color switch during the movement

gobo wheel speed

tracking mode

fast→slow

tracking mode

color switch during the movement

prism speed

moderate speed

color switch during the movement

Control menu

Menu Item

Secondary

project

option

Note (bold is for default

setting)

Address — —

1-512 DMX address

Specific

X Reverse —

Normal DMX pan

controlling left→right

OPEN

Reversal DMX pan

controlling right→left

Y Reverse —

Normal DMX tilt

controlling up→down

OPEN

Reversal DMX tilt

controlling down→up

X、Y Swap —

Normal pan&tilt

controlling channels

OPEN

Exchange pan&tilt

controlling channels

http:// en.fineart-light.com

- 31 -

8/16bit —

23 CH 23 channel controlling mode

31 CH 31 channel controlling mode

Lamp PWR —

Lamp on-off is

uncontrollable by DMX

OPME

Lamp on-off is

controlled by DMX

Soft RST —

Channel reset is

controllable by DMX

OPEN

Channel reset is

controlled by DMX

Shortest —

OPEN

Color/gobo/effect wheel

in reverse route

Colr/gobo/effect

wheel in shortest route

PWR Save —

CLOSE lamp is brightest

OPEN

DMX controls electric

linear dimmer

Fan Contl —

DMX can not

control fan speed

OPEN

DMX can control fan

speed

Speed

X Y SP

FASH X、Y high speed mode

MIDDLE X、Y medium speed mode

SLOW X、Y low speed mode

X Y Smoot — 0-9

0-9, X 、 Y smooth

adjustment

Channel

Channel 01 — 0-255

shutter→on/off→strobe→qui

ck→resetlighter

Channel 02 — 0-255 0%-100% dimmer

Channel 03 — 0-255 CMY Cyan

http:// en.fineart-light.com

- 32 -

Channel 04 — 0-255 CMY Magenta

Channel 05 — 0-255 CMY Yellow

Channel 06 — 0-255

color wheel

smooth switch→stepping

switch→continuous

rotation→random position

and color

Channel 07 — 0-255

gobo wheel I

Static gobo→rotatable

gob→dithering gobo

→rotation of gobo wheel

Channel 08 — 0-255

gobo wheel I

angle orientation/ rotation

speed and direct of the gobo

Channel 09 — 0-255

gobo wheel I

16bit

Channel 10 — 0-255

gobo wheel II

smooth switch→

tepping switch→continuous

otation→ Random position

and gobo

Channel 11 — 0-255

gobo/color

Macro function of gobo

wheel II and color wheel I

and color wheel II

Channel 12 — 0-255

animation gobo

open→default

position→continuous rotation

animation Macro function

http:// en.fineart-light.com

- 33 -

Channel 13 — 0-255

animation gobo angle/

speed angle orientation/

the rotation speed and direct

of the gobo

Channel 14 — 0-255

prism

open→insert→rotation→pri

sm Macro function

Channel 15 — 0-255

Iris

on/off→opening/closing

pulse →random

opening/closing pulse

Channel 16 — 0-255

focus

infinity→2m

Channel 17 — 0-255

Zoom

0-100% linear adjustment

Channel 18 — 0-255 X-axis rough adjustment

Channel 19 — 0-255 X-axis precise adjustment

Channel 20 — 0-255 Y-axis rough adjustment

Channel 21 — 0-255 Y-axis precise adjustment

Channel 22 — 0-255

an/tilt speed control

Channel 23 — 0-255

Effect speed

Dimmer, animation wheel,

focus and zoom/

color speed/gobo speed/

gobo wheel speed/

rism speed

Channel 24

…

Channel 40

0-255

http:// en.fineart-light.com

- 34 -

Adjust

Slot 00 — 0000-FFFF dimmer excursion

Slot 01 — 0000-FFFF magenta excursion

Slot 02 — 0000-FFFF iris excursion

Slot 03 — 0000-FFFF zoom excursion

Slot 04 — 0000-FFFF

rotation of animation wheel

excursion

Slot 05 — 0000-FFFF focus excursion

Slot 06 — 0000-FFFF

Animation wheel glide

excursion

Slot 07 — 0000-FFFF gobo II excursion

Slot 08 — 0000-FFFF yellow excursion

Slot 09 — 0000-FFFF cyan excursion

Slot 10 — 0000-FFFF

rism rotation excursion

Slot 11 — 0000-FFFF

Slot 12 — 0000-FFFF Gobo I rotation excursion

Slot 13 — 0000-FFFF Gobo I glide excursion

Slot 14 — 0000-FFFF Prism open excursion

Slot 15 — 0000-FFFF

Slot 16 — 0000-FFFF Color wheel II excursion

Slot 17 0000-FFFF pan excursion

Slot 18 0000-FFFF tilt excursion

Slot 19

…

Slot 23

0000-FFFF

Message

Lamp TMR — —

display the total operation

hours of the lamp

CLR TMR — — Clear time

Tools Chalevel

Rec 01 000-255 strobe control

Rec 02 000-255 Dimmer control

Rec 03 000-255 CMY Cyan

Rec 04 000-255 CMY Magenta

http:// en.fineart-light.com

- 35 -

Rec 05 000-255 CMY Yellow

Rec 06 000-255 Color wheel

Rec 07 000-255 Gobo wheel I

Rec 08 000-255

orientation speed of gobo

wheel I

Rec 09 000-255

16bit

Gobo wheel I 16bit

Rec 10 000-255 Gobo wheel II

Rec 11 000-255 gobo/color macro function

Rec 12 000-255 Animataion gobo

Rec 13 000-255

animation gobo

orientation speed

Rec 14 000-255 prism

Rec 15 000-255 iris

Rec 16 000-255 focus

Rec 17 000-255 zoom

Rec 18 000-255

X-axis rough adjust-

ment

Rec 19 000-255

X-axis precise adjust-

ment

Rec 20 000-255

Y-axis rough adjust-

ment

Rec 21 000-255

Y-axis precise adjust-

ment

Rec 22 000-255 Speed of X-axis and Y-axis

Rec 23 000-255 Effect speed

Code

Code 0 —

Product information for

inquiry

Code 1 —

Code 2 —

Code 3 —

Code 4 —

http:// en.fineart-light.com

- 36 -

Code 5 —

Code 6 —

Code 7 —

Code 8 —

Code 9 —

Code 11 —

Code 12 —

Code 13 —

Code 14 —

Code 15 —

Reset

Home

Manual reset of fixture

Reset

Routine Maintenance

FINE700 series products require routine maintenance. The service life

is mainly depends on the working environment. Please consult the Fine Art

technicians and refer any service operation that is not described here to a

qualified Fine Art technician.

Note! Damage caused by excessive dust, smoke fluid and inadequate

use is not covered by the warranty.

Warning! Disconnect the fixture from power before removing any

cover.

Tilt Lock

The tilt position of the head can be locked for transportation and service

with the tilt lock. See picture 1: to lock or unlock the head, pull the lock out

and turn it one-quarter turn in either direction.

Dismount

The dismount of the pattern module

1. See picture 14: Turn the four retaining screws in the top and bottom

head covers one quarter-turn counter-clockwise to release the covers.

http:// en.fineart-light.com

- 37 -

Picture 14

2. See picture 15: Turn the fixture to the proper position and pull the

strap I as shown in the picture, so that the magnifier reaches to top

position which is near the light head.

Picture 15

3. See picture 16: Pull the strap II to make the focus lens reach to the

top position which is near the light head.

http:// en.fineart-light.com

- 38 -

Picture 16

4. See picture 17: Turn the fixture to the proper position; pull the

strap in the direction shown in the picture so that the animation

wheel moves to the module center. Please avoid bending the

animation wheel when taking out the module.

Picture 17

5. See picture 18: Unlock the gobo module by pulling the levers on

each side towards the center, and then lift the module straight up to

remove from the head.

http:// en.fineart-light.com

- 39 -

Picture 18

6. When reinstalling the module, verify that the guide pins are

correctly seated and that the module is securely locked.

The dismount of the strobe modules

1. See Picture 19: Like the gobo module, the strobe module is also

can be released by pulling the levers on each side towards the center,

and then lift the strobe module straight up to remove from the head.

Picture 19

2. When reinstalling the strobe module, verify that the guide pins are

correctly seated and that the module is securely locked.

Note: The gobo module must be removed before the strobe module.

http:// en.fineart-light.com

- 40 -

Cleaning

Regular cleaning can prolong the service life and ensure the good

performance of the fixture. Use care when cleaning optical components. The

coated surfaces are fragile and easily scratched. Do not use solvents that can

damage plastic or painted surfaces.

Cleaning of optical components

1、Disconnect the fixture from power and allow the components to cool

completely, and then remove the cover.

2、Vacuum or gently blow away dust and loose particles with compressed

air.

3 、 Remove stuck particles with an unscented tissue or cotton swab

moistened with glass cleaner or distilled water. Do not rub the surface

and blow away loose particles with compressed air

4、 Remove smoke and other residues with cotton swabs or unscented

tissues moistened with isopropyl alcohol. A commercial glass cleaner

may be used, but residues must be removed with distilled water. Clean

with a slow circular motion from center to edge and dry with a soft

cotton cloth.

Cleaning of fan and air vent

Remove dust from the head fans and air vents with a soft brush, cotton

paper, vacuum, or compressed air.

Cleaning and replacement of the air filter

1、See picture 20: Disconnect the fixture from the power supply. On each

side of the fixture, remove the 2 screws that hold the side covers with

cross screwdriver; slide the covers forward to remove, and then remove

the air filter.

2、Get rid of the dust in the air filter with cleaner or pressed air. If they are

saturated with smoke fluid, etcetera, soak them in warm soapy water

and blot dry

3、Position the filters on the side covers and reinstall it.

Page is loading ...

Fine Art FINE700 User manual

Brand: Fine Art

Model: FINE700

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

Fine Art FINE700 User manual

Fine Art FINE700 User manual

Other documents