NIDEC SANKYO WJ6ICM0M0-1X90 User manual

Type
User manual

NIDEC SANKYO WJ6ICM0M0-1X90 is a wireless radio frequency transceiver module designed for use in embedded applications. It operates in the 2.4 GHz frequency band (2400 MHz to 2483.5 MHz) and is compliant with the IEEE 802.15.4 standard. The module supports various modulation schemes, including BPSK, QPSK, and OQPSK, and can operate at data rates up to 250 kbps. It has a built-in antenna and is capable of transmitting and receiving data over a range of approximately 100 meters (line of sight).

NIDEC SANKYO WJ6ICM0M0-1X90 is a wireless radio frequency transceiver module designed for use in embedded applications. It operates in the 2.4 GHz frequency band (2400 MHz to 2483.5 MHz) and is compliant with the IEEE 802.15.4 standard. The module supports various modulation schemes, including BPSK, QPSK, and OQPSK, and can operate at data rates up to 250 kbps. It has a built-in antenna and is capable of transmitting and receiving data over a range of approximately 100 meters (line of sight).

Manual Requirement of FCC
Our product (FCC ID: WJ6ICM0M0-1X90) will be sold and installed into certain end products.
Therefore, we will not supply the user’s manual. However, we will ask the end-product
manufacturer to include following statements in the end-product user manual in accordance
with FCC requirements.
Also, Installation manual is included in Theory of Operation as it contains technical
confidential information.
Requirement for User Manual
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Properly shielded and grounded cables and connectors must be used for connection to host
computers and / or peripherals in order to meet FCC emission limits.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures :
-- Reorient or relocate the receiving antenna
-- Increase the separation between the equipment and receiver
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Requirement for Product Label
we will ask the end-product manufacturer to affix the following on the end-product.
- Contains FCC ID : WJ6ICM0M0-1X90
  • Page 1 1
  • Page 2 2

NIDEC SANKYO WJ6ICM0M0-1X90 User manual

Type
User manual

NIDEC SANKYO WJ6ICM0M0-1X90 is a wireless radio frequency transceiver module designed for use in embedded applications. It operates in the 2.4 GHz frequency band (2400 MHz to 2483.5 MHz) and is compliant with the IEEE 802.15.4 standard. The module supports various modulation schemes, including BPSK, QPSK, and OQPSK, and can operate at data rates up to 250 kbps. It has a built-in antenna and is capable of transmitting and receiving data over a range of approximately 100 meters (line of sight).

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI