Philips HD7830 User manual

Brand: Philips

Model: HD7830

Category: Coffee makers

Type: User manual

2 3 4 5

7 8 9

10 11 12

14 15 16 17

18 19 20 21

22 23 24 25

27 28 29

30 31 32 33

34 35

HD7830

Coffee Machine

RQO

ENGLISH

Introduction

With Douwe Egberts SENSEO

coffee pods, you can

enjoy a perfect cup of coffee at any time of the day. Every

cup is freshly brewed to give you that smooth and full

taste.

Using more than 250 years of coffee expertise, Douwe

Egberts has roasted and ground specially selected coffee

beans that, when prepared using a special brewing

method co-developed with Philips, ensure a full, smooth

taste and delicious foam layer. This joint creation, known

as the SENSEO

coffee pod system, consists of the

Philips SENSEO

coffee machine and specially developed

Douwe Egberts SENSEO

coffee pods. Only when used

together will you be rewarded with a sensational cup of

SENSEO

coffee with the delicious SENSEO

foam layer.

To ensure a smooth and full coffee taste, you should keep

the following things in mind:

Fresh water

Use fresh water every day. If you have not used the coffee

machine for three days, you have to ush it with fresh

water before you use it again (see section ‘Flushing’ in

chapter ‘Cleaning’).

Fresh coffee pods

Use the SENSEO

coffee pods that have been specially

developed by Douwe Egberts for your SENSEO

coffee

machine for a full, round taste. The Douwe Egberts

SENSEO

coffee pods will stay fresh longer if you store

them in an airtight storage container.

A clean machine

Clean and descale your Philips SENSEO

coffee machine

regularly (see chapters ‘Cleaning’ and ‘Descaling’). Remove

used coffee pods after brewing. If a used pod has been

left in the coffee machine and you have not used the

machine for some time, ush the machine before you use

it again (see section ‘Flushing’ in chapter ‘Cleaning’).

General description (Fig. 1)

A Display

1 Heat-up indication

2 Coffee volume indication

3 Water rell indication

4 Descaling indication

B Volume select button

C Outow valve

D Water reservoir

E Grip area

F Sealing ring

G Water distribution disc

H 1-cup pod holder q

I 2-cup pod holder qq

J Cover of coffee spout

K Coffee spout

L Coffee collector

M Cup tray

N Drip tray

O 1-cup button q

P Water level light rings

Q On/off button with indicator light

R 2-cup button qq

Important

Read these instructions for use carefully before using the

machine and save them for future reference.

Check if the voltage indicated on the bottom of

the machine corresponds to the local mains voltage

before you connect the machine.

If the mains cord is damaged, it must be replaced

by Philips, a service centre authorised by Philips

or similarly qualied persons in order to avoid a

hazard.

To prevent unexpected contact with hot water,

always make sure the lid of the SENSEO

machine

is properly locked before you start using the

machine.

Never put normal ground coffee or use torn pods

in the SENSEO

machine, as this will cause it to

become blocked.

Do not use the machine in combination with

a transformer, as this could cause hazardous

situations.

Put the machine on a at, stable surface.

Never let the machine operate unattended.

Do not use the machine at altitudes higher than

2200 metres above sea level.

The machine does not work at temperatures below

10 °C.

Flush the coffee machine with fresh water before

using it for the rst time (see chapter ‘Preparing

the machine for use’). This will cause the boiler to

ll with water, which is essential for the machine to

work properly.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and in accordance with the instructions in this

instruction manual, the appliance is safe to use according

to scientic evidence available today.

Preparing the machine for use

YOU CANNOT BREW COFFEE IF YOU HAVE NOT

FLUSHED THE SENSEO

COFFEE MACHINE FIRST!

Note that the display will not work until you have

ushed the machine.

The ushing cycle causes the boiler to be lled with

water. After this the coffee machine is ready for use.

Flush the machine in the following way:

1 Remove the water reservoir (Fig. 2).

2 Fill the water reservoir with cold water up to

the MAX indication and put it back onto the

machine. (Fig. 3)

3 Release the lid by moving the lever upwards (Fig. 4).

4 Open the lid (Fig. 5).

5 Put the 1-cup pod holder q or the 2-cup pod

holder qq in the machine without pod(s). (Fig. 6)

6 Close the lid and lock the lever (Fig. 7).

Note: Make sure the lever is properly locked by pushing it

down until it snaps home with a click.

Note: Never ush the machine with the lid open. The lid

must be properly locked.

7 Put the plug in an earthed wall socket.

8 Put a bowl (with a capacity of at least 1500

ml) under the spout openings to collect the

water. (Fig. 8)

9 Press the on/off button 3. (Fig. 9)

After pressing the on/off button 3, the display lights up

for a moment and the light rings around the 1-cup button

q and the 2-cup button qq burn continuously.

10 Press the 1-cup button q and the 2-cup button

qq briey at the same time. (Fig. 10)

The boiler lls itself with water from the water

reservoir. This may take some time (approx.

90 to 150 seconds). The machine switches off

automatically when the ushing cycle ends. During

the ushing cycle the machine produces more noise

than during a regular brewing cycle.

Never interrupt the ushing cycle halfway. If you do, the

boiler will not ll itself properly.

Note: Before you use the machine for the rst time, clean

the coffee spout, the coffee collector and the pod holders

with hot water and some washing-up liquid or in the

dishwasher. Clean the water reservoir thoroughly in hot

water, if necessary with some washing-up liquid.

Now your Philips SENSEO

coffee machine is ready for

use.

Brewing coffee

1 Fill the water reservoir with cold water up to

the MAX indication and put it back onto the

machine. (Fig. 3)

Never pour milk, coffee, hot water or carbonated water

into the water reservoir.

q MIN: minimum amount of water required to brew

1 cup of SENSEO

coffee.

qq MIN: minimum amount of water required to

brew 2 cups of SENSEO

coffee.

A full reservoir allows you to make 6 large cups h, 8

medium cups g or

10 small cups f of SENSEO

coffee. This makes it

unnecessary to ll the water reservoir each time you

want to make a cup of coffee.

2 Press the on/off button 3. (Fig. 9)

The indicator light blinks slowly and the display

shows the heat-up indication D while the water

is heating up. Heating up takes approx. 90

seconds. (Fig. 11)

The coffee machine is ready for use when the

indicator light burns continuously and the light rings

around the 1- cup button q and the 2-cup button

qq go on.

If the indicator light blinks rapidly and the display

shows the water rell indication s, the water

reservoir does not contain enough water for

brewing one cup of coffee. (Fig. 12)

If there is not enough water for brewing two cups

of coffee, the light ring around the 2-cup button

qq will not go on and this button cannot be

operated.

3 Release the lid by moving the lever upwards (Fig. 4).

4 Open the lid.

5 Place the appropriate pod holder in the machine.

Note: Make sure the pod holder is clean and the sieve in the

centre is not clogged, e.g. with loose coffee grounds.

If you want to make one cup of SENSEO

coffee,

use 1 coffee pod in combination with the 1-cup pod

holder q and the 1-cup button q. (Fig. 13)

If you want to make two cups of SENSEO

coffee,

use 2 coffee pods in combination with the deeper

2-cup pod holder qq and the 2-cup button

qq. (Fig. 14)

6 Place the SENSEO

coffee pod(s) properly in the

centre of the pod holder, with the convex side

pointing downwards.

Note: Use SENSEO

coffee pods from Douwe Egberts

specially designed for your SENSEO

coffee machine for a

full and round taste.

Note: Make sure the coffee in the pod(s) is evenly distributed

and press the pod(s) lightly into the pod holder.

Note: Never put normal ground coffee or use torn pods

in the SENSEO

machine, as this will cause it to become

blocked.

Place 1 SENSEO

coffee pod in the 1-cup pod

holder q. (Fig. 15)

Place 2 SENSEO

coffee pods in the 2-cup pod

holder qq. (Fig. 16)

7 Close the lid and lock the lever (Fig. 7).

Always check if the lid is properly locked. The lever must

be pushed down until it snaps home with a click.

Never start brewing with the lid open. The lid must be

properly closed.

8 Place one cup or two cups under the spout

openings. You can adjust the height of the coffee

spout by sliding it upwards or downwards (Fig. 17).

The cups you use should have a capacity of at least

100ml when brewing small cups f, 150ml when brewing

medium cups g and 170ml when brewing large cups h

of SENSEO

coffee. Do not use cups that are too large,

as they will cause the coffee to get cold more quickly.

9 Select the desired coffee volume by pressing the

volume select button j.

By varying the volume, you will also affect the

strength of the coffee.

Select 1 bar for a small cup of coffee (80

ml) (Fig. 18)

Select 2 bars for a medium cup of coffee (125

ml) (Fig. 19)

Select 3 bars for a large cup of coffee (145

ml) (Fig. 20)

10 Press the button indicating the number of cups of

SENSEO

coffee you want to brew. (Fig. 21)

Press the 1-cup button q for one cup.

Press the 2-cup button qq for two cups.

4222.001.9946.2

2/4

The light rings around the 1-cup button q and the 2-cup

button qq indicate if there is still enough water left for

brewing one or two cups of coffee. If there is not enough

water left in the water reservoir for brewing two cups

of coffee, the light ring around the 2-cup button qq will

not go on and this button cannot be operated.

The SENSE

coffee machine starts brewing.

The machine automatically supplies the selected

amount of water.

You can interrupt the brewing process at any time

by pressing the on/off button 3. If you switch

the machine back on after having interrupted the

brewing process, the machine will not complete the

interrupted brewing cycle.

Do not remove the water reservoir during a brewing

cycle, as this will cause the machine to draw in air. When

this happens, the next cup will only be partly lled.

Note: If you only get a small quantity of coffee or no coffee

at all out of the machine, you have not ushed the machine

properly before rst use. As a result, the boiler is not or not

completely lled. Flush the machine properly (see chapter

‘Preparing the machine for use’) before you brew another

cup of coffee.

11 Remove the coffee pod(s) after use by lifting the

pod holder out of the machine and emptying it.

Be careful when doing this, for there may still be some

water/coffee on the coffee pod(s).

Tips

By rinsing the pod holders, the coffee collector and

the coffee spout regularly, you will make sure that

the coffee always tastes optimally.

The SENSEO

coffee will taste best if you stir it

before drinking it.

If you intend to make another cup of SENSEO

coffee later, just leave the coffee machine switched

on. The machine will automatically switch itself off

after 1 hour. (Fig. 22)

Cleaning

Never immerse the SENSEO

coffee machine in water.

Never clean the machine by ushing it with the lid open.

1 Always unplug the machine before cleaning it.

2 Clean the outside of the machine with a moist

cloth.

3 Remove the coffee collector (Fig. 23).

4 Take the coffee spout out of the machine by sliding

it upwards (Fig. 24).

The coffee spout can only be taken out after the coffee

collector has been removed.

You can disassemble the coffee spout for more

thorough cleaning! (Fig. 25)

5 Clean the coffee spout, the coffee collector and

the drip tray in hot water, if necessary with some

washing-up liquid, or in the dishwasher (Fig. 26).

6 Hold the cup tray in your hand while cleaning it

with hot water, if necessary with some washing-up

liquid (Fig. 27).

The cup tray can also be cleaned in the dishwasher.

To clean the cup tray, always remove it from the

machine, as it might prove sharp when handled

incorrectly. Always handle it carefully.

7 Clean the pod holders in hot water, if necessary

with some washing-up liquid, or in the

dishwasher. (Fig. 28)

Check if the sieve in the centre of the pod holder is

clogged. If this is the case, unclog the sieve by rinsing the

pod holder under a running tap. Use a washing-up brush

to clean the sieve, if necessary.

8 Clean the water reservoir in hot water, if necessary

with some washing-up liquid. (Fig. 29)

Note: If you are using a washing-up brush, be careful not to

damage the valve in the bottom of the water reservoir.

9 Do not use an object with sharp edges to clean the

water inlet on the machine (Fig. 30).

10 Rinse the parts with fresh water after cleaning and

put them back into the machine.

11 Clean the water distribution disc with a moist

cloth (Fig. 31).

Be careful when you do this; make sure that the rubber

sealing ring does not get stuck under the edge of the

water distribution disc. If it does, the coffee machine will

start leaking!

Flushing

If you have not used the coffee machine for three days,

you have to ush it with fresh water before you use it

again.

Flush the machine in the following way:

1 Fill the water reservoir with cold water up to

the MAX indication and put it back into the

machine. (Fig. 3)

2 Put the 1-cup pod holder q or the 2-cup pod

holder qq in the machine without pod(s). (Fig. 13)

3 Put a bowl (with a capacity of at least 1500 ml)

under the coffee spout to collect the water (Fig. 8).

4 Press on/off button 3 (1) and subsequently press

the 1-cup button q and the 2-cup button qq

briey at the same time (2). (Fig. 32)

The machine lls itself with water from the water

reservoir. While this happens, water comes out of

the spout. When the ushing cycle is nished, the

machine switches itself off. During the ushing cycle,

the machine produces more noise than during a regular

brewing cycle.

Descaling

Regular descaling will prolong the life of the coffee

machine and will guarantee optimal brewing results for a

long time.

When you need to descale the machine, the

descaling indication b appears on

the display. This happens after 500 cups have

been brewed. After another 8 cups, the descaling

indication b disappears from the display

(whether or not you have performed the descaling

procedure). (Fig. 33)

1 Fill the water reservoir up to the MAX indication

with descaler and water according to the

instructions on the package of the descaler. Then

put the water reservoir back into the coffee

machine. (Fig. 3)

Use a liquid descaler based on citric acid.

2 Press the on/off button 3. (Fig. 9)

The machine is ready for use when the indicator light

burns continuously.

3 Place the 1-cup pod holder q in the coffee

machine, preferably with a used coffee pod in it.

Close the lid and make sure it is properly locked.

We advise you to put a used coffee pod in the pod

holder when you descale the machine. This pod will serve

as a ‘lter’ to prevent the sieve in the pod holder from

getting clogged with scale residues.

4 Put a bowl with a capacity of at least 1500 ml

under the spout openings to collect the mixture of

descaler and water. (Fig. 8)

5 Press the 2-cup button qq for 2 cups and let

the machine operate. Repeat this until the water

reservoir is empty. (Fig. 34)

Never descale the SENSEO

coffee machine with the

lid open. Make sure the lid is properly locked.

6 Repeat steps 1 to 5 with a new mixture of descaler

and water.

7 Empty the water reservoir to remove the mixture

of descaler and water.

8 Rinse the machine at least 3 times by repeating

steps 1 to 5, now using fresh water.

Do not rell the water reservoir with used hot

water.

9 Clean the pod holder after descaling to prevent the

sieve in the centre from getting clogged.

Frost-free storage

If the coffee machine has already been used and

therefore has been ushed with water, it may only be

used and stored in a frost-free place to prevent it from

becoming damaged.

Replacement

All removable parts can be ordered from your Philips

dealer or a Philips service centre.

Environment

Do not throw the machine away with the normal

household waste at the end of its life, but hand

it in at an ofcial collection point for recycling.

By doing this you will help to preserve the

environment (Fig. 35).

Guarantee & service

If you need service or information or if you have a

problem, please consult the worldwide guarantee leaet

or visit our website at www.philips.com. You can also

contact the Philips Customer Care Centre in your

country; they will be happy to help you.

The telephone number for the United Kingdom is: 0845-

6010354.

You will nd the telephone numbers for other countries

in the worldwide guarantee leaet. If there is no

Customer Care Centre in your country, turn to your

local Philips dealer or contact the Service Department of

Philips Domestic Appliances and Personal Care BV. You

will nd their address and fax number in the worldwide

guarantee leaet.

The purchase of the Philips SENSEO

coffee machine

does not exhaust any of the rights of Sara Lee/Douwe

Egberts or Philips under any of their patents nor does it

confer upon the purchaser a licence under these patents.

4222.001.9946.2

3/4

Troubleshooting

If you have a problem, you may nd the solution in the

table below. If the table does not provide the solution

to your problem or if you have a question, see chapter

‘Guarantee & service’.

Problem Solution

The indicator light

continues to blink

slowly.

You have not yet ushed the

coffee machine (see chapter

‘Preparing the machine for use’).

You have used the SENSEO

coffee machine at an altitude

higher than 2200 metres above

sea level. This has caused the

water in the machine to start

boiling before it has reached

the required temperature,

which prevents the machine

from functioning properly.

Switch the machine off and no

longer use it at altitudes higher

than 2200 metres above sea

level.

The SENSEO

coffee machine does

not produce coffee

when used for the

rst time.

You have not yet ushed the

coffee machine. When you use

the machine for the rst time,

you have to ush it before you

can start brewing coffee (see

chapter ‘Preparing for use’).

The display doesn’t

work when the

machine is switched

on for the rst time.

You have not yet ushed the

coffee machine. The display

starts working after the

machine has been ushed (see

chapter ‘Preparing for use’).

The indicator light

continues to blink

rapidly.

Make sure that:

the water reservoir has been

properly placed;

there is enough water in the

water reservoir (i.e. above the

q MIN level if you want to

brew 1 cup);

the ambient temperature is

not lower than 10

C. If it is,

the machine will not function

properly.

The 2-cup button

qq cannot be

operated.

Make sure that there is enough

water in the water reservoir

for brewing 2 cups of coffee. If

the light ring around the 2-cup

button qq is out, there is not

enough water in the water

reservoir for brewing 2 cups.

Water leaks from

the coffee machine.

Make sure that:

the lid is properly closed (the

lever must be properly locked);

the water reservoir has not

been lled beyond the MAX

level;

the sieve in the centre of the

pod holder is not clogged. If it

is, unclog the sieve by holding

the pod holder under a running

tap. If necessary, you can use a

washing-up brush or a pin to

unclog the sieve;

the coffee pod has been put

properly in the centre of the

pod holder;

Problem Solution

the sealing ring is not stuck

under the edge of the water

distribution disc.

the water drops on the

worktop are not the result of

placing or removing the water

reservoir or removing used

coffee pods;

you do not remove the water

reservoir when the coffee

machine is heating up. This may

cause water that normally ends

up in the water reservoir to

leak out of the machine.

In all other cases, contact the

Philips Customer Care Centre

in your country.

The coffee spout

cannot be taken out

of the machine.

The coffee spout can only

be taken out after the coffee

collector has been removed.

The lid cannot be

opened.

A vacuum may have

temporarily formed under

the lid.

Switch the machine off. Pull the

lever up as far as it will go and

wait 24 hours before opening

the lid. You may need to use

quite some force.

Make sure that the sieve in

the centre of the pod holder

is not clogged. If it is, unclog

the sieve by holding the pod

holder under a running tap.

If necessary, you can use a

washing-up brush or a pin to

unclog the sieve.

If problems continue to occur,

contact the Philips Customer

Care Centre in your country.

The coffee machine

produces less coffee

than before.

Perhaps the sieve in the centre

of the pod holder is clogged. If

this is the case, unclog the sieve

by rinsing the pod holder under

a running tap. Use a washing-

up brush to clean the sieve, if

necessary.

Descale the machine (see

chapter ‘Descaling’).

The SENSEO

coffee machine

brews only a small

quantity of coffee

or no coffee at all

when it is used for

the rst time.

You have not ushed the

machine properly before rst

use. As a result, the boiler is

not or not completely lled.

Flush the machine properly (see

chapter ‘Preparing the machine

for use’) before you brew

another cup of coffee.

The lid cannot be

closed properly.

Check if a used coffee pod

is sticking to the water

distribution disc. If this is the

case, remove the used pod.

Check if you used the correct

pod holder. Use 2 pods in

combination with the deeper

2-cup pod holder qq.

Use 1 pod in combination with

the 1-cup pod holder q.

The machine has

been stored in a

room that was not

frost-free.

Contact the Philips Customer

Care Centre in your country.

Problem Solution

The SENSEO

coffee is not strong

enough.

Make sure that:

you have used the correct

number of pods and have

pressed the right button. Use

1 pod in combination with the

1-cup pod holder q and the

1- cup button q.

Use 2 pods in combination with

the 2-cup pod holder qq and

the 2-cup button qq.

the coffee pod(s) have been

placed properly in the centre

of the pod holder, to prevent

water from escaping along the

edge of the pod(s). When you

are using two coffee pods on

top of each other, make sure

that the convex sides of both

pods are pointing downwards

and press the pods lightly into

the pod holder;

you have not used the same

pod twice by accident;

the coffee in the pod is evenly

distributed;

If you prefer a more robust

avour, SENSEO

coffee pods

with a stronger blend are

available.

The SENSEO

coffee is too strong.

If you prefer a milder avour,

SENSEO

coffee pods with a

milder blend are available.

The coffee is not

hot enough.

Do not use cups that are too

large, as they will cause the

coffee to get cold more quickly.

Make sure the cups have a

capacity of at least 100 ml

when brewing small cups f,

150 ml when brewing medium

cups g and 170ml when

brewing large cups h.

The preferred coffee

volume cannot be

selected.

Make sure that there is enough

water in the water reservoir.

The coffee volume

indication does

not appear on the

display and it is not

possible to select a

volume.

Make sure that there is enough

water in the water reservoir.

4222.001.9946.2

4/4

Philips HD7830 User manual

Brand: Philips

Model: HD7830

Category: Coffee makers

Type: User manual

Download PDF

report

Philips HD7830 User manual

Philips HD7830 User manual

Related papers

Other documents