Biostar 945P-A7G Owner's manual

945P-A7G/945PL-A7G Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protec tion against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. There is no guarantee

that interference will not occur in a particular ins tallation.

The vendor makes no represe ntatio ns o r warranties with respec t to the

contents here and specially disclaims any implied warranties of merchantability

o r fi tness fo r a ny p u rp ose . F urt he r t he ve ndo r res e rves t he ri g ht to rev ise t his

publication and to make changes to the contents here without obligation to

notify any party beforehand.

D uplication of this publication, in part or in whole, is not allowed without first

obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and

we will not be res ponsible for any mis takes found in this user’s manual. All the

brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction .............................................1

1.1 Before You Start...................................................................1

1.2 Package Checklist................................................................1

1.3 Motherboard Features..........................................................2

1.4 Rear Panel Connectors (Ver 6.x)............................................ 4

1.5 Rear Panel Connectors (Ver 5.x)............................................ 4

1.6 Motherboard Layout (for Ver 6.x)..........................................5

1.7 Motherboard Layout (for Ver 5.x).......................................... 6

Chapter 2: Hardware Installation..............................7

2.1 Installing Central Processing Unit (CPU)................................7

2.2 FAN Headers........................................................................9

2.3 Installing System Memory.....................................................10

2.4 Connectors and Slots............................................................12

Chapter 3: Headers & Jumpers Setup .....................14

3.1 How to Setup Jumpers..........................................................14

3.2 Detail Settings.....................................................................14

Chapter 4: Useful Help .............................................19

4.1 Driver Installation Note .......................................................19

4.2 Award BIOS Beep Code........................................................20

4.3 Extra Information................................................................20

4.4 Troubleshooting...................................................................21

Chapter 5: WarpSpeeder™ III .................................22

5.1 Introduction........................................................................22

5.2 System Requirement............................................................22

5.3 Installation.........................................................................23

5.4 WarpSpeeder™ III................................................................24

Appendencies: SPEC In Other Language ................30

German................................................................................................30

France..................................................................................................32

Italian..................................................................................................34

Spanish................................................................................................36

Portuguese...........................................................................................38

Polish...................................................................................................40

Russian................................................................................................42

Arabic..................................................................................................44

Japanese..............................................................................................46

945P-A7G/945PL-A7G

1

CHAPTER 1: INTRODUCTION

1.1 B

EFORE YOU START

Tha nk you for choosing our pro duct. Before yo u sta rt installing the

mo the rboa rd , plea se make sure you fo llow the instructions be low:

 Prepare a dry and stable working environment with

s ufficie nt ligh ting .

 Always disconnect the computer from power outlet

be fo re ope ra tion.

 Befo re you take the mo the rboa rd ou t f rom a n ti-s ta tic

bag, ground yourself properly by touching any safely

grounde d appliance, o r use grounded wrist strap to

remove the static charge.

 Avo id tou ch ing the compone nts o n mo the rboa rd o r the

rear side of the board unless necessary. Hold the board

on the edge, do not try to bend or flex the board.

 Do not leave any unfastene d sma ll parts inside the

case after installation. Loose parts will cause short

circuits which ma y damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and wate r.

1.2 PACKAGE CHECKLIST

HDD Cable x 1

Se ria l ATA Cab le x 1

Use r’s Manual x 1

Fully Setup Driver CD x 1

Rear I/O Panel for ATX Case x 1

FDD Cable x 1 (optional)

USB 2.0 Cable x 1 (optiona l)

S/PDIF Cable x 1 (optional)

Se ria l ATA Po we r Cab le x 1 (o p tio nal)

Note: The package contents may differ by area or your motherboard version.

Motherboard Manual

2

1.3 MOTHERBOARD FEATURES

945P-A7G 945PL-A7G

CPU

LGA 77 5

Intel Core2Duo / Pentium 4 / Pentium D /

Celeron D processor up to 3.8 GHz

Supports Hy per -Thre ading

Execute Disable Bit

Enha nced Intel SpeedStep

Extende d Memor y 64 Tech nolog y

LGA 77 5

Intel Core2Duo / Pentium 4 / Pentium D /

Celeron D processor up to 3.8 GHz

Supports Hy per -Thre ading

Execute Disable Bit

Enha nced Intel SpeedStep

Extende d Memor y 64 Tech nolog y

FSB 533 / 80 0 / 1 06 6 MHz 533 / 80 0 / 1 06 6 MHz

Chipset

Intel 9 45P

Intel ICH7

Intel 9 45PL

Intel ICH7

Super I/O

ITE IT 87 12F

H/W Monitor

Fan Spee d Co ntroller

ITE's "Smart G uardia n" fu nction

ITE IT 87 12F

H/W Monitor

Fan Spee d Co ntroller

ITE's "Smart G uardia n" fu nction

Main

Memory

DIMM Slots x 4

Eac h DIMM sup ports 2 56/ 51 2MB & 1GB

DDR2

Max Memory C apicity 4GB

Dual Channel Mode DDR 2 memory module

Supports D DR2 5 33 / 667

DIMM Slots x 2

Eac h DIMM sup ports 2 56/ 51 2MB & 1GB

DDR2

Max Memory C apicity 2GB

Dual Channel Mode DDR 2 memory module

Supports D DR2 4 00 / 533

IDE

Integrated I DE Controller

Ultra DMA 33~100 Bus Master Mode

supports PIO Mo de 0~4,

Integrated I DE Controller

Ultra DMA 33~100 Bus Master Mode

supports PIO Mo de 0~4,

SATA

Integrated Serial ATA Controller

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 specification compliant.

Integrated Serial ATA Controller

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 specification compliant.

LAN

Realtek RTL 8110SC

10/ 100 /1000 Mb/s auto neg otiation

Half / Full duplex capability

Realtek RTL 8110SC

10/ 100 /1000 Mb/s auto neg otiation

Half / Full duplex capability

Sound

Codec

ALC861VD(Ver 6.x) / ALC88 8(Ver 5.x)

5.1 c ha nnels a udio o ut (Ver 6.x)

7.1 c ha nnels a udio o ut (Ver 5.x)

High- Defi nition Audio s upport

ALC861VD(Ver 6.x) / ALC88 8(Ver 5.x)

5.1 c ha nnels a udio o ut (Ver 6.x)

7.1 c ha nnels a udio o ut (Ver 5.x)

High- Defi nition Audio s upport

945P-A7G/945PL-A7G

3

945P-A7G 945PL-A7G

PCI Express x 16 slot x1 PCI Express x 16 slot x1

PCI Express x 1 slot x2 PCI Express x 1 slot x2 Slots

PCI slot x3 PCI slot x3

Floppy connector x1 Floppy connector x1

IDE Co nnector x1 IDE Co nnector x1

SATA Connector x4 SATA Connector x4

Front Pa nel Co nnector x1 Front Pa nel Co nnector x1

Front Audi o Co nnector x1 Front Audi o Co nnector x1

CD-in Co nnector x1 CD-in Co nnector x1

S/PDIF out connector x1 S/PDIF out connector x1

CPU Fan hea der x1 CPU Fan hea der x1

System Fan hea der x1 System Fan hea der x1

Chassis open header (optional) x1 Chassis open header (optional) x1

Clear CMOS header x1 Clear CMOS header x1

USB connector x2 USB connector x2

Power Connector (24pi n) x1 Power Connector (24pi n) x1

On Board

Connector

Power Connector (4pin) x1 Power Connector (4pin) x1

Back Panel

I/O

PS/2 Keyboard x1

PS/2 Mo use x1

Serial Port x1

Printer Port x1

LAN port x1

USB Port x4

Audio J ack (Ver 6.x) x3

Audio J ack (Ver 5.x) x6

PS/2 Keyboard x1

PS/2 Mo use x1

Serial Port x1

Printer Port x1

LAN port x1

USB Port x4

Audio J ack (Ver 6.x) x3

Audio J ack (Ver 5.x) x6

Board Size 205 (W) x 30 5 (L) mm 205 (W) x 30 5 (L) mm

OS

Support

Windows 2000 / XP / VISTA

Biostar Reserves the ri

g

ht to add or remo ve

support for any OS with or without notice.

Windows 2000 / XP / VISTA

Biostar Reserves the ri

g

ht to add or remove

support for any OS with or without notice.

Motherboard Manual

4

1.4 REAR PANEL CONNECTORS (VER 6.X)

PS/2

Mouse

PS/ 2

Keyboard

USBX2USBX2

LAN

COM1

Lin e In/

Surround

Line Out

Mic In 1/

Bass/ Center

Printer Port

1.5 REAR PANEL CONNECTORS (VER 5.X)

PS/2

Mouse

PS/ 2

Keyboard

USBX2USBX2

LA N

COM1

Line In

Line Out

Mic In

Center

Re ar

Side

Pr int e r P ort

Since t he au dio c hip s up por ts Hig h Definiti on A udio Specific atio n, t he func tion of eac h a udi o

jack c an be d efine d b y sof twar e. T he in pu t / out pu t fu nctio n o f e ach au dio jac k listed ab o ve

represe nts t he def ault s etti ng. Ho wever, when c on necti ng e xter nal microph on e t o t he au dio

port, pleas e us e t he Lin e I n ( blu e) an d Mic In (Pin k) a udio j ac k.

945P-A7G/945PL-A7G

5

1.6 MOTHERBOARD LAYOUT (FOR VER 6.X)

DDR2_A1

DDR 2_A2 (Only for 945P-A7G )

DDR2_B1

DDR 2_B2 (Only for 945P-A7G )

FDD1

IDE1

PEX1

_

1

PEX1

_

2

PEX16_1

PCI1

PCI 2

PCI 3

JPA NEL 1

JATX PW R1

JC FA N1

JATX PWR 2

JAUDIO 1

JAUDIOF1

Super

I/O

JC I1

(

O

p

tional

)

JCMOS1

SATA1

SATA2

SATA3

SATA4

Codec

JCDIN1

JSP DI F

_

OU T

JSFAN1

10 /1 00 LA N

BAT1

BIOS

JKBMS1

JRJ45USB1

Intel

ICH7

LGA775

CPU1

C

O

M

1

J

C

O

M

1

Intel

945P

or

945PL

JPRNT1

Note: ■ represents the 1

st

pin.

Motherboard Manual

6

1.7 MOTHERBOARD LAYOUT (FOR VER 5.X)

DDR2_A1

DDR 2_A2 (Only for 945P-A7G )

DDR2_B1

DDR 2_B2 (Only for 945P-A7G )

FDD1

IDE1

PEX1

_

1

PEX1

_

2

PEX16_1

PCI1

PCI 2

PCI 3

JPA NEL 1

JATX PW R1

JC FAN1

JATX PWR2

JAUDIO2

JAUDIOF1

Super

I/O

JC I1

(

O

p

tional

)

JCMOS1

SATA1

SATA2

SATA3

SATA4

Codec

JCDIN1

JSP DI F

_

OUT

JSFAN1

10 /1 00 LA N

BAT1

BIOS

JKBMS1

JRJ45USB1

Intel

ICH7

LGA775

CPU1

CO M1JC OM1

Intel

945P

or

945PL

JPRNT1

Note: ■ represents the 1

st

pin.

945P-A7G/945PL-A7G

7

CHAPTER 2: HARDWARE INSTALLATION

2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Special Notice:

Remove Pin Cap before installation, and make good preservation

for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin-Cap

Step 1: Pull the socket locking lever out from the socket and then raise the

lever up to a 90-degree angle.

Motherboard Manual

8

Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will

fit only in the correct orientation.

Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked

position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it

on the retention frame. Connect the CPU FAN power cable into

the JCFAN1. This completes the installation.

945P-A7G/945PL-A7G

9

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan

cable and connector may be different according to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to

pin#1.

JCFAN1: CPU Fan Header

Assignment

1 Ground

2 +12V

3 FAN RPM rate

sense

1

4

JCFAN1

4 Smart Fan

Control

JSFAN1: System Fan Header

Assignment

1 Ground

2 +12V

JSFAN1

31

3 FAN RPM rate

sense

Note:

The JCFAN1 a nd JSFAN1 s up port 4- pin and 3-pin h ead co nnec tor. W he n co nn ecting

with wir es ont o c onn ect ors, ple ase no te that t he r e d wir e is t he positi ve an d s houl d b e

conn ected t o pi n#2, and th e bl ac k wire is Gro und a nd s ho uld b e c on nect ed to GND.

Motherboard Manual

10

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DDR2_A1

DDR2_A2( On ly for )945P-A7G

DDR2_B1

DDR2_B2( On ly for )945P-A7G

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the

break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining

chip snap back in place and the DIMM is properly seated.

945P-A7G/945PL-A7G

11

B. Memory Capacity

For 945P-A7G

DIMM Socket

Location

DDR Module Total Memory Size

DDR2_A1 256MB/512MB/1GB *1

DDR2_A2 256MB/512MB/1GB *1

DDR2_B1 256MB/512MB/1GB *1

DDR2_B2 256MB/512MB/1GB *1

Max memory 4GB.

For 945PL-A7G

DIMM Socket

Location

DDR Module Total Memory Size

DDR2_A1 256MB/512MB/1GB *1

DDR2_B1 256MB/512MB/1GB *1

Max memory 2GB.

C. Dual Channel Memory installation

To trigger the Dual Channel f unction of the motherboard, the memory module

must meet the following requirements:

Install memory module of the same density in pairs, shown in the f ollowing table.

For 945P-A7G

Dual Channel Status

DDR2_A1

DDR2_A2 DDR2_B1 DDR2_B2

Enabled O X O X

Enabled X O X O

Enabled O O O O

For 945PL-A7G

Dual Channel Status

DDR2_A1

DDR2_B1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or

x16)

Motherboard Manual

12

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard prov ides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the

prov ided f loppy drive ribbon cable.

1

234

33

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

The IDE connector can connect a master and a slave drive, so y ou can connect

up to two hard disk driv es.

IDE1

40

21

39

945P-A7G/945PL-A7G

13

PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

- Maximum theoretical realized bandwidth of 4GB/s simultaneously per

direction, f or an aggregate of 8GB/s totally.

PEX1_1/PEX1_2: PCI-Express x1 Slots

- PCI-Express 1.0a compliant.

- Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total.

- PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

- 2X bandwidth ov er the traditional PCI architecture.

PEX16_1

PEX1_1

PEX1_2

PCI1/PCI2/PCI3: Peripheral Component Interconnect Slots

This motherboard is equipped with 3 standard PCI slots. PCI stands f or

Peripheral Component Interconnect, and it is a bus standard for expansion

cards. This PCI slot is designated as 32 bits.

PCI3

PCI2

PCI1

Motherboard Manual

14

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SET UP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is

placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SET T ING S

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep

button, and speaker connection. It allows user to connect the PC case’s front

panel switch functions.

1

SLP

PW R

_

LED

On/Off

RST

HLED

SP K

++

+

8

-

916

Pin Assignment Function Pin Assignment Function

1 +5V 9 Sleep control

2 N/A 10 Ground

Sleep button

3 N/A 11 N/A N/A

4 Speaker

Speaker

connector

12 Power LED (+)

5 HDD LED (+) 13 Power LED (+)

6 HDD LED (-)

Hard drive LED

14 Power LED (-)

Power LED

7 Ground 15 Power button

8 Reset control

Reset button

16 Ground

Power-on button

945P-A7G/945PL-A7G

15

JATXPWR1: ATX Power Source Conne ctor

This connector allows user to connect 24-pin power connector on the ATX

power supply.

Pin Assignment

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

9 Standby Voltage

+5V

10 +12V

11 +12V

12 2 x 12 Detect

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 -5V

21 +5V

22 +5V

23 +5V

13

1

24 12

24 Ground

JATXPWR2: ATX Power Source Conne ctor

By connecting this connector, it will provide +12V to CPU power circuit.

Assignment

1 +12V

2 +12V

3 Ground

3

41

2

4 Ground

Motherboard Manual

16

JUSB3/JUSB4: Headers for USB 2.0 Ports at Front Panel

This motherboard prov ides 2 USB 2.0 headers, which allows user to connect

additional USB cable on the PC front panel, and also can be connected with

internal USB dev ices, like USB card reader.

Assignment

1 +5V (fused)

2 +5V (fused)

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

210

9

1

JUSB3 JUSB4

10 NC

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC f ront

panel. It will disable the output on back panel audio connectors.

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

6 Jack Sense

7 Front Sense

8 Key

9 Left line in

10 Jack Sense

1

9

2

10

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source f rom the v ariaty dev ices,

like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc..

Assignment

1 Left Channel

Input

2 Ground

3 Ground

14

4 Right Channel

Input

945P-A7G/945PL-A7G

17

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting

and the CMOS data, please carefully f ollow the procedures to avoid damaging

the motherboard.

13

Pin 1-2 Close:

Normal Operation (Default).

13

Pin 2-3 Close:

Clear CMOS data.

※ Clear CMOS Procedures:

1. Remov e AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait f or f ive seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

JCI1: Chassis O pen Heade r (Optional)

This connector allows system to monitor PC case open status. If the signal has

been triggered, it will record to the CMOS and show the message on next

boot-up.

Assignment

1 Case open signal

12

2 Ground

Motherboard Manual

18

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interf ace, it

satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

SATA 4

SATA1 SATA 3

SATA2

174

7 Ground

JSPDIF_OUT: Digital Audio out Connectors

This connector allows user to connect the PCI bracket SPDIF output

header.

Assignment

1 +5V

2 SPDIF_OUT

31

3 Ground

Page is loading ...

Biostar 945P-A7G Owner's manual

Biostar 945P-A7G Owner's manual

Related papers

Other documents