Frigidaire FPHI2188PF User manual

Category
Fridge-freezers
Type
User manual
TABLE OF CONTENTS
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
All about the
Use & Care
of your Refrigerator
Important Safety Instructions ......................2
Installation ................................................4
Door Removal Instructions ..........................5
Handle Installation .....................................6
Connecting Water Supply ............................8
Ice Service ...............................................10
807876502 (September 2013)
Controls ...................................................10
Normal Operating Sounds and Sights ......... 11
Care and Cleaning ....................................12
Before you Call .........................................14
Major Appliance Warranty .........................15
2
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
IMPORTANT
IMPORTANT indicates installation, operation or
maintenance information which is important but
not hazard-related.
DANGER
DANGER indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
Denitions
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol
to avoid possible injury or death.
Doors
Handles are secure and tight
Door seals completely to cabinet on all sides
Freezer door is level across the top
Leveling
Refrigerator is level, side-to-side and tilted
¼” (6mm) front-to-back
Toe grille is properly attached to refrigerator
Cabinet is setting solid on all corners
Electrical Power
House power turned on
Refrigerator plugged in
Ice Maker
House water supply connected to
refrigerator
No water leaks present at all connections -
recheck in 24 hours
Ice maker is turned ON
Ice & water dispenser operates correctly
Frontltermustbeushwithlterhousing
(select models)
Final Checks
Shipping material removed
Fresh food and freezer temperatures set
Crisper humidity controls set
Registration card sent in
Installation Checklist
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
IMPORTANT SAFETY INSTRUCTIONS
For your Safety
• DO NOT store or use gasoline, or other
ammableliquidsinthevicinityofthisor
any other appliance. Read product labels for
warningsregardingammabilityandother
hazards.
• DO NOT operate the refrigerator in the
presence of explosive fumes.
• Avoid contact with any moving parts of
automatic ice maker.
• Remove all staples from the carton. Staples
can cause severe cuts, and also destroy
nishesiftheycomeincontactwithother
appliances or furniture.
WARNING
Please read all instructions before using this
refrigerator.
Child Safety
Destroy or recycle the carton, plastic bags, and
any exterior wrapping material immediately after
the refrigerator is unpacked. Children should never
use these items to play. Cartons covered with
rugs, bedspreads, plastic sheets or stretch wrap
maybecomeairtightchambers,andcanquickly
cause suffocation.
Proper Disposal of your Refrigerator
or Freezer
Risk of child entrapment
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators or
freezers are still dangerous – even if they will sit for
“just a few days”. If you are getting rid of your old
refrigerator or freezer, please follow the instructions
below to help prevent accidents.
3
IMPORTANT SAFETY INSTRUCTIONS
Grounding type wall receptacle
Power cord with
3-prong grounded plug
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
Electrical information
• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., 15 Amp, AC only
electrical outlet. The power cord of the appliance
isequippedwithathree-pronggroundingplug
for your protection against electrical shock
hazards. It must be plugged directly into a
properly grounded three prong receptacle. The
receptacle must be installed in accordance with
localcodesandordinances.Consultaqualied
electrician. Avoid connecting refrigerator to a
Ground Fault Interrupter (GFI) circuit. Do not
use an extension cord or adapter plug.
• If the power cord is damaged, it should be
replaced by an authorized service technician to
prevent any risk.
• Never unplug the refrigerator by pulling on the
powercord.Alwaysgriptheplugrmly,and
pull straight out from the receptacle to prevent
damaging the power cord.
• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.
• Performance may be affected if the voltage varies
by 10% or more. Operating the refrigerator with
insufcientpowercandamagethecompressor.
Such damage is not covered under your warranty.
• Do not plug the unit into an electrical outlet
controlled by a wall switch or pull cord to prevent
the refrigerator from being turned off accidentally.
WARNING
These guidelines must be followed to ensure
that safety mechanisms in this refrigerator will
operate properly.
IMPORTANT
Turning the Freezer and Fresh Food controls
to “0” (Mechanical controls) will disable your
refrigerator’s cooling system, but does not
disconnect the power to the light bulb and
other electrical components. To turn off power
to your refrigerator you must unplug the power
cord from the electrical outlet.
CAUTION
To avoid personal injury or property damage,
handle tempered glass shelves carefully. Shelves
may break suddenly if nicked, scratched, or
exposed to sudden temperature change.
Proper Disposal of Refrigerators/Freezers
We strongly encourage responsible appliance
recycling/disposal methods. Check with your utility
company or visit www.recyclemyoldfridge.com for
more information on recycling your old refrigerator.
Before you throw
away your old
refrigerator/freezer:
• Remove doors.
• Leave shelves in
place so children
may not easily climb
inside.
• Have refrigerant
removed by a
qualiedservice
technician.
IMPORTANT
CFC/HCFC Disposal
Your old refrigerator may have a cooling system
thatusedCFCsorHCFCs(chlorouorocarbons
orhydrochlorouorocarbons).CFCsandHCFCs
are believed to harm stratospheric ozone if
released to the atmosphere. Other refrigerants
may also cause harm to the environment if
released to the atmosphere.
If you are throwing away your old refrigerator,
make sure the refrigerant is removed for
properdisposalbyaqualiedtechnician.If
you intentionally release refrigerant, you may
besubjecttonesandimprisonmentunder
provisions of environmental legislation.
4
NOTE
If your refrigerator is placed with the door
hinge side against a wall, you may have to
allow additional space so the door can be
opened wider.
NOTE
Raise the front of the refrigerator enough so
the doors close freely when opened halfway.
The refrigerator should slope ¼” to ½” from
front to back. Then level the refrigerator from
side-to-side.
INSTALLATION
CAUTION
Do Not install the refrigerator where the
temperature will drop below 55°F (13°C) or rise
above 110°F (43°C). The compressor will not
be able to maintain proper temperatures inside
the refrigerator.
Do Not block the toe grille on the lower front of your
refrigerator.Sufcientaircirculationisessentialfor
the proper operation of your refrigerator.
This Use & Care Guide provides general operating
instructions for your model. Use the refrigerator
only as instructed in this Use & Care Guide. Before
starting the refrigerator, follow these important
rststeps.
Location
• Choose a place that is near a grounded
electrical outlet. Do Not use an extension cord
or an adapter plug.
• If possible, place the refrigerator out of direct
sunlight and away from the range, dishwasher
or other heat sources.
• Therefrigeratormustbeinstalledonaoor
that is level and strong enough to support a
fully loaded refrigerator.
• Consider water supply availability for models
equippedwithanautomaticicemaker.If
you do not hook up water to the refrigerator,
remember to turn the ice maker off.
Installation
Installation clearances
• Allow the following clearances for ease
of installation, proper air circulation, and
plumbing and electrical connections:
Sides&Top ⅜inch
Back 1 inch
Leveling
All four corners of your refrigerator must rest
rmlyonasolidoor.Yourrefrigeratorisequipped
with adjustable front rollers or front leveling
screws to help level your unit.
Raise
Raise
Adjustable Front Roller (some models)
Stationary Front Roller with Leveling Screw
(some models)
To level your
refrigerator:
1. Remove
toe grille.
2. Useat-
blade
screwdriver
or⅜”
socket
wrench to
adjust front rollers. Use adjustable wrench to
adjust leveling screws.
5
NOTE
The direction in which your
refrigerator doors open (door swing)
can be reversed, from left to right
or right to left, by moving the door
hinges from one side to the other.
Reversing the door swing should be
performedbyaqualiedperson.
DOOR REMOVAL INSTRUCTIONS
Top Hinge
Cover Front
Screw
Top Hinge
Cover Rear
Screw
Bottom
Hinge
Screw
Top
Hinge
Screw
Door removal and reversal instructions:
1. Remove toe grille.
2. Remove top hinge cover. Trace around the hinge with a soft
lead pencil. This makes reinstallation easier. Remove top
hinge and lift door off center hinge pin. Set door aside.
3. Unscrew center hinge pin using adjustable wrench and save
for reassembly. Ensure plastic washer stays on hinge pin.
4. Lift refrigerator door off of bottom hinge and set aside.
5. Remove center hinge and shim by removing inside screw
and loosening two outside screws enough to allow hinge
and shim to slide out. Tighten screws.
6. Loosen two outside screws on opposite side of refrigerator,
remove inside screw and install center hinge.
7. Removetwoscrewsonbottomhingewith⅜”socketwrench.
8. Install bottom hinge on opposite side with the two screws
removed from step 7.
9. Unscrew bottom hinge pin using adjustable wrench. Move hinge
pin to other hole in hinge and tighten with adjustable wrench.
10. Reverse door handles (see instruction on next page).
11. Move freezer and refrigerator door stops to opposite side.
Before starting screws, use an awl to puncture the foam.
12. Position refrigerator door onto bottom hinge pin and screw
center hinge pin through center hinge into top of door. Close
refrigerator door to help align hinge hole.
13. Tighten center hinge pin with adjustable wrench.
14. Remove cabinet and hinge hole plugs and move to opposite side.
15. Lower freezer door onto center hinge pin.
16. Close freezer door. Have an assistant lift up on opposite side
of door while tightening screws to install top hinge.
17. Flip toe grille and reinstall.
18. Plug in electrical power cord and turn refrigerator temperature
control to center position. Adjust setting as necessary.
IMPORTANT
Before you begin, turn the
refrigerator temperature control to
“0” and remove the electrical power
cord from the wall outlet. Remove
any food from door shelves.
Door
Stop
Shim
Washer
Hinge
Pin
Center
Hinge
Screws
Hinge
Hole
Plug
Handle
Hole
Plug
Door
Stop
Screw
Washer
Hinge
Pin
Bottom
Hinge
Screws
Toe
Grille
Door Stop
Screw
Door
Stop
Top
Hinge
Cover
Top
Hinge
Adjustable
Wrench
Socket
Wrench Set
3/8" Fixed
Wrench
Tools Necessary:
Phillips
TM
Head
oror
6
IMPORTANT
To ensure proper installation of handles, please
review these instructions and illustrations
thoroughly prior to installing the handles.
Additionally, before installing the door handles,
make sure the door swing is correct. Your
model will have either a right hand or left hand
door swing. Follow instructions in the Use &
Care Guide to reverse the doors, if necessary.
HANDLE INSTALLATION
To attach metal refrigerator handle:
1. Place rounded part of handle onto shoulder
screw on face of door and align the two holes
in top of handle with the two holes in top of
door. Do not tighten the set screw yet.
2. Install the two screws into the top of the
handle.
3. Tighten the set screw on the rounded part of
thehandleuntilthehandleisushwiththe
door, then tighten another ½ turn.
CAUTION
Wear gloves and use extreme CAUTION when
installing these handles. The rounded end of
the handles may be sharp.
To attach metal freezer handle:
1. Place rounded part of handle onto shoulder
screw on face of door and align the two holes
in bottom of handle with the two holes in
bottom of door. Do not tighten the set screw
yet.
2. Install the two screws into the bottom of the
handle.
Stainless Steel Models
Screw
Handle
Button
Plug
Set
Screw
Shoulder
Screw
Shoulder
Screw
Nameplate
Handle
Set
Screw
Screw
Screw
Handle
Shoulder
Screw
Set
Screw
3. Tighten the set screw on the rounded part of
thehandleuntilthehandleisushwiththe
door, then tighten another ½ turn.
Shoulder
Screw
Set
Screw
Handle
Screw
7
To reverse refrigerator/freezer handles:
Handles may be easier to reverse while doors are
off. Reverse freezer and refrigerator handles as
shown.
CAUTION
Be sure doors are set aside in a secure position
where they cannot fall and cause personal
injury.
To attach plastic refrigerator handle:
1. Place top of handle over dovetail screw, pull
handle straight down until handle is aligned
with screw holes on top of door.
2. Secure top of handle with two screws.
To attach plastic freezer handle:
1. Place top of handle over dovetail screw, pull
handle straight up until handle is aligned with
screw holes on bottom of door.
2. Secure bottom of handle with two screws.
HANDLE INSTALLATION
Screw
Handle
Button
Plug
Lock Handle
over
Dovetail Screw
Dovetail
Screw
Screw
Dovetail
Screw
Lock Handle
over
Dovetail Screw
Handle
Screw
Nameplate
8
CONNECTING THE WATER SUPPLY
Before Installing The Water Supply Line,
You Will Need:
• BasicTools:adjustablewrench,at-blade
screwdriver, and Phillips
TM
screwdriver
• Access to a household cold water line with
water pressure between 30 and 100 psi.
• A water supply line made of ¼ inch (6.4
mm) OD, copper or stainless steel tubing.
To determine the length of tubing needed,
measure the distance from the ice maker inlet
valve at the back of the refrigerator to your
cold water pipe. Then add approximately 7
feet (2.1 meters), so the refrigerator can be
moved out for cleaning (as shown).
• A shutoff valve to connect the water supply
line to your household water system. DO NOT
use a self-piercing type shutoff valve.
• A compression nut and ferrule (sleeve) for
connecting a copper water supply line to the
ice maker inlet valve.
WARNING
To avoid electric shock, which can cause
death or severe personal injury, disconnect
the refrigerator from electrical power before
connecting a water supply line to the
refrigerator.
CAUTION
To Avoid Property Damage:
• Copper or Stainless Steel braided tubing
is recommended for the water supply line.
Water supply tubing made of ¼ inch plastic
is not recommended to be used. Plastic
tubing greatly increases the potential for
water leaks, and the manufacturer will not be
responsible for any damage if plastic tubing
is used for the supply line.
• DO NOT install water supply tubing in areas
where temperatures fall below freezing.
• Chemicals from a malfunctioning softener
can damage the ice maker. If the ice maker
is connected to soft water, ensure that the
softener is maintained and working properly.
IMPORTANT
Ensure that your water supply line connections
comply with all local plumbing codes.
NOTE
Check with your local building authority
for recommendations on water lines and
associated materials prior to installing your
new refrigerator. Depending on your local/
state building codes, Frigidaire recommends for
homes with existing valves its Smart Choice
®
water line kit 5305513409 (with a 6 ft. Stainless
Steel Water Line) and for homes without an
existing valve, Frigidaire recommends its Smart
Choice
®
water line kit 5305510264 (with a 20
ft. Copper Water Line with self-tapping saddle
valve). Please refer to www.frigidaire.com/store
for more information.
To Connect Water Supply Line To Ice Maker
Inlet Valve
1. Disconnect refrigerator from electric power
source.
2. Place end of water supply line into sink or
bucket.TurnONwatersupplyandush
supply line until water is clear. Turn OFF water
supply at shutoff valve.
3. Remove plastic cap from water valve inlet and
discard cap.
4. If you use copper tubing - Slide brass
compression nut, then ferrule (sleeve) onto
water supply line. Push water supply line into
water valve inlet as far as it will go (¼ inch
/ 6.4 mm). Slide ferrule (sleeve) into valve
inletandngertightencompressionnut
onto valve. Tighten another half turn with a
wrench; DO NOT over tighten. See Figure 1.
If you use stainless steel tubing - The nut and
ferrule are already assembled on the tubing.
Slide compression nut onto valve inlet and
ngertightencompressionnutontovalve.
Tighten another half turn with a wrench; DO
NOT over tighten. See Figure 2.
5. With steel clamp and screw, secure water
supply line (copper tubing only) to rear panel
of refrigerator as shown.
6. Coil excess water supply line (copper tubing
only), about 2½ turns, behind refrigerator
as shown and arrange coils so they do not
vibrate or wear against any other surface.
7. Turn ON water supply at shutoff valve and
tighten any connections that leak.
8. Reconnect refrigerator to electrical power
source.
9
IMPORTANT
After connecting the water supply, refer to
“How to Prime the Water Supply System” for
important information about priming an empty
water supply system.
Your refrigerator’s water supply system includes
severaltubinglines,awaterlter,awater
valve, and a water tank. To ensure that your
water dispenser works properly, this system
mustbecompletelylledwithwaterwhenyour
refrigeratorisrstconnectedtothehousehold
water supply line.
Figure 1
Figure 2
Steel
Clamp
Stainless
Steel
water Line
Water Valve
Bracket
Valve Inlet
Water Valve
6 ft. Stainless Steel water line
from household water supply
Plastic Water Tubing
to Ice Maker
Fill Tube
Plastic Water
Tubing to Ice
Maker Fill
Tube
Steel
Clamp
Brass
Compression
Nut
Ferrule
(Sleeve)
Copper
water line
Water Valve
Bracket
Valve Inlet
Water Valve
Copper water line
from household
water supply
(Include enough tubing in loop
to allow moving refrigerator out
for cleaning.)
CONNECTING THE WATER SUPPLY
9. To turn ice maker on, lower wire signal arm
(side mounted) or set the ice maker’s On/
Off power switch to the “I” position (rear
mounted).
10
IMPORTANT
Turning the refrigerator/freezer temperature control
to “0” turns off the compressor and prevents the
refrigerator from cooling, but does not disconnect
the power to the light bulb and other electrical
components. To turn off power to your refrigerator,
you must unplug the power cord from the wall outlet.
NOTE
Whenrstturningrefrigeratoron,movecontrol(s)
to Normal. This is the recommended initial setting.
After 24 hours, adjust the controls as needed.
IMPORTANT
Your ice maker is shipped from the factory with
the wire signal arm in the ON position. To ensure
proper function for your ice maker, hook up water
supply immediately or turn ice maker OFF by
lifting the wire signal arm until it clicks and locks
in the UP position. If the ice maker is not turned
off and the water supply is not connected, the
water valve will make a loud chattering noise.
Auxiliary Freezer Control
Normal
ColderCold
Refrigerator/Freezer Control
Normal
Cold Colder
Allow 24 hrs for adjustments
Temperature Adjustment
• Adjust temperature gradually: move the knob
in small increments, allowing the temperature
to stabilize.
Turning the refrigerator/freezer control will change
temperatures in both compartments. The auxiliary
freezer control has no effect on electrical power to
the refrigerator.
To maintain temperatures, a fan circulates air in the
refrigerator and freezer compartments. For good
circulation, do not block cold air vents with food items.
CONTROLSICE SERVICE
If your refrigerator has an automatic ice maker,
noicewillbeproducedduringtherst24hours
of operation. Air in new plumbing lines may cause
the ice maker to cycle two or three times before
making a full tray of ice. With no usage, it will take
approximatelyonetotwodaystolltheicecontainer.
Newplumbingconnectionsmaycausetherst
production of ice cubes to be discolored or have an
oddavor.Discardicemadeduringtherst24hours.
Turning your Ice Maker On
After the plumbing connections have been
completed, the water supply valve must be
opened. Place the ice container under the ice
maker, pushing it as far back as possible. Lower
the wire signal arm to its “down” or ON position.
Turning your Ice Maker Off
To stop the ice maker, lift the wire signal arm until
it clicks and locks in the “up” or OFF position. The
ice maker also turns off automatically when the
ice container is full.
NOTE
Automatic ice makers are also optional accessories
that may be installed in most models at any time.
Call your local dealer for information.
Wire
Signal Arm
ON
OFF
Cool Down Period
To ensure safe food storage, allow the refrigerator
to operate with the doors closed for at least 8 to
12 hours before loading it with food.
Refrigerator & Freezer Controls
11
NOTE
Rigidfoaminsulationisveryenergyefcient,
but is not a sound insulator.
Understanding the sounds you may
hear
Yournew,high-efciencyrefrigeratormayintroduce
unfamiliar sounds. These sounds normally indicate
your refrigerator is operating correctly. Some
surfacesonoors,walls,andkitchencabinetsmay
make these sounds more noticeable.
IMPORTANT
During the automatic defrost cycle, you may
notice a red glow in the vents on the back wall
of your freezer compartment. This is normal
during the defrost cycle.
Following is a list of major components in your
refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the
evaporator may create a boiling or gurgling
sound.
B Evaporator fan You may hear air being
forced through the refrigerator by the
evaporator fan.
C Defrost heater During defrost cycles, water
dripping onto the defrost heater may cause a
hissing or sizzling sound. After defrosting, a
popping sound may occur.
D Automatic ice maker When ice has been
produced, you will hear ice cubes falling into
the ice bin. The ice maker will produce 2.5 to
3 pounds of ice every 24 hours depending on
usage conditions.
E Automatic defrost control These parts can
produce a snapping or clicking sound when
turning the cooling system on and off.
F Condenser fan You may hear air being
forced through the condenser.
G CompressorModern,high-efciency
compressors run much faster than in the
past. The compressor may have a high-
pitched hum or pulsating sound.
H Water valve Makes a buzzing sound each
timeitopenstolltheicemaker.
I Drain pan (not removable) You may hear
water dripping into the drain pan during the
defrost cycle.
J Condenser May create minimal sounds from
forced air.
A
B
C
D
E
F
G
H
I
J
NORMAL OPERATING SOUNDS AND SIGHTS
12
IMPORTANT
If you store or move your refrigerator in freezing temperatures, be sure to completely drain the water
supply system. Failure to do so could result in water leaks when the refrigerator is put back into
service. Contact a service representative to perform this operation.
CAUTION
• Pulltherefrigeratorstraightouttomoveit.Shiftingitfromsidetosidemaydamageooring.Be
careful not to move the refrigerator beyond the plumbing connections.
• Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp
hands.
NOTE
If you set your temperature controls to turn off cooling, power to lights and other electrical
components will continue until you unplug the power cord from the wall outlet.
Protecting your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any spills
immediately and clean the freezer and fresh food compartments at least twice a year. When cleaning,
take the following precautions:
• Never use CHLORIDE or cleaners with bleach to clean stainless steel.
• Do not wash any removable parts in a dishwasher.
• Always unplug the electrical power cord from the wall outlet before cleaning.
• Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which can
scratch the appliance surface.
• Do not remove the serial plate.
Donotuseabrasivecleanerssuchaswindowsprays,scouringcleansers,brushes,ammableuids,
cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on
plastic parts, interior doors, gaskets or cabinet liners. Do not use paper towels, metallic scouring pads,
or other abrasive cleaning materials or strong alkaline solutions.
CARE & CLEANING
13
Care & Cleaning Tips
Part What To Use Tips and Precautions
Interior &
Door Liners
• Soap and water
• Baking soda and water
Use2tablespoonsofbakingsodain1quartofwarmwater.
Be sure to wring excess water out of sponge or cloth before
cleaning around controls, light bulb or any electrical part.
Door
Gaskets
• Soap and water Wipe gaskets with a clean soft cloth.
Drawers &
Bins
• Soap and water Use a soft cloth to clean drawer runners and tracks.
Glass
Shelves
• Soap and water
• Glass cleaner
• Mildliquidsprays
Allow glass to warm to room temperature before immersing
in warm water.
Toe Grille • Soap and water
• Mildliquidsprays
• Vacuum attachment
Vacuum dust from front of toe grille. Remove toe grille (see
Installation Instructions). Vacuum backside, wipe with sudsy
cloth or sponge. Rinse and dry.
Exterior &
Handles
• Soap and water
• Non Abrasive Glass
Cleaner
Do not use commercial household cleaners containing
ammonia, bleach or alcohol to clean handles. Use a soft
cloth to clean smooth handles. DO NOT use a dry cloth to
clean smooth doors.
Exterior &
Handles
(Stainless
Steel Models
Only)
• Soap and water
• Stainless Steel
Cleaners
Never use CHLORIDE or cleaners with bleach to clean
stainless steel.
Clean stainless steel front and handles with non-abrasive
soapy water and a dishcloth. Rinse with clean water and a
soft cloth. Use a non-abrasive stainless steel cleaner. These
cleaners can be purchased at most home improvement or
major department stores. Always follow manufacturers
instructions. Do not use household cleaners containing
ammonia or bleach.
NOTE: Always clean, wipe and dry with the grain to prevent
scratching. Wash the rest of the cabinet with warm water
andmildliquiddetergent.Rinsewell,andwipedrywitha
clean soft cloth.
Replacing
Light Bulbs
• Unplug refrigerator
• Wear gloves
• Remove light cover
• Replace old bulb
• Replace light cover
• Plug in the refrigerator
CAUTION: Wear gloves when replacing light bulbs to avoid
getting cut. Use same wattage when replacing bulb
CARE & CLEANING
14
Common Occurrences
Before calling for service, review this list. It may save you time
and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
Refrigerator does not run. • Ensure plug is tightly pushed into electrical outlet.
• Check/replace fuse with a 15 amp time-delay fuse. Reset circuit
breaker.
• The refrigerator/freezer control is turned to “0”.
• Refrigerator may be in defrost cycle. Wait 20 minutes and check
again.
Freezer temperature too cold.
Refrigerator temperature is
satisfactory.
• Set auxiliary freezer control to a warmer setting until freezer
temperature is satisfactory. Allow 24 hours for the temperature
to stabilize.
Refrigerator temperature is too
cold. Freezer temperature is
satisfactory.
• Set refrigerator/freezer control to a warmer setting. Allow
24 hours for temperature to stabilize. Then check freezer
temperatures and adjust as needed.
Refrigerator is noisy or vibrates. • The cabinet is not level.
• Floor is weak.
• See Normal Operating Sounds and Sights section.
Odors in refrigerator. • Interior needs to be cleaned.
• Foods that produce odors should be covered or wrapped.
Cabinet light not working. • Replace light bulb.
• Ensure plug is tightly pushed into electrical outlet.
• Light switch may be stuck. Push in light switch, located on the
refrigerator control box, to release.
Automatic ice maker not
working (some models)
• Ensure the wire signal arm is not in UP position.
• Ice maker should produce 2.5 to 3 pounds of ice in a 24 hour
period.
• Water supply is turned off.
• Water pressure is too low.
• The freezer is not cold enough.
BEFORE YOU CALL
Visit our web site at
www.frigidaire.com.
1-800-944-9044 (United States)
1-800-265-8352 (Canada)
15
MAJOR APPLIANCE WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase,
Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective
in materials or workmanship when such appliance is installed, used and maintained in accordance with the
provided instructions.
Exclusions
If You Need Service
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the
USA or Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not in
ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Servicecallstorepairorreplaceappliancelightbulbs,airlters,waterlters,otherconsumables,or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12.Damagestothenishofapplianceorhomeincurredduringinstallation,includingbutnotlimitedto
oors,cabinets,walls,etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine
Electrolux parts or parts obtained from persons other than authorized service companies; or external causes
suchasabuse,misuse,inadequatepowersupply,accidents,res,oractsofGod.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE
YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX
SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE
AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY
OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF
IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux
Major Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is
warranted by Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations
under this warranty. Obligations for service and parts under this warranty must be performed by Electrolux
oranauthorizedservicecompany.Productfeaturesorspecicationsasdescribedorillustratedaresubject
to change without notice.
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
shouldserviceberequired.Ifserviceisperformed,itisinyourbestinteresttoobtainandkeepallreceipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers
below.
USA
1.800.944.9044
Frigidaire
10200 David Taylor Drive
Charlotte, NC 28262
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Frigidaire FPHI2188PF User manual

Category
Fridge-freezers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI