Trendnet TPE-S88 Owner's manual

Trendnet
Brand
Trendnet
Model
TPE-S88
Category
Network switches
Type
Owner's manual

Trendnet TPE-S88 is an advanced networking device that combines the functionality of a switch and a power over Ethernet (PoE) injector. It is equipped with 8 10/100Mbps Power-over-Ethernet ports and 8 10/100Mbps ports, allowing you to connect various network devices such as computers, IP cameras, VoIP phones, and access points.

The PoE ports on the TPE-S88 can provide power to compatible devices, eliminating the need for separate power cables. This makes it ideal for powering devices in locations where it may be difficult or inconvenient to run additional cabling, such as on ceilings or in remote areas.

Trendnet TPE-S88 is an advanced networking device that combines the functionality of a switch and a power over Ethernet (PoE) injector. It is equipped with 8 10/100Mbps Power-over-Ethernet ports and 8 10/100Mbps ports, allowing you to connect various network devices such as computers, IP cameras, VoIP phones, and access points.

The PoE ports on the TPE-S88 can provide power to compatible devices, eliminating the need for separate power cables. This makes it ideal for powering devices in locations where it may be difficult or inconvenient to run additional cabling, such as on ceilings or in remote areas.

Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TPE-S88
Version 01.07.05
Power-over-Ethernet Smart Switch
Quick Installation Guide
Commutateur intelligent Power-over-Ethernet
Guide d'installation rapide
PoE-Smart-Switch
Kurzanleitung zur Installation
Guía de instalación rápida de
conmutador inteligente de Power-over-Ethernet (PoE)
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
2
3
4
9
1. Prepare for Installation ......................................................................
2. Product Detail .....................................................................................
3. Hardware Installation ........................................................................
4. Configure the Power-over-Ethernet Web Smart Switch ...................
Thank you for purchasing TRENDnet's TPE-S88 Power-over-Ethernet Smart
Switch. This guide will help you set up your Power-over-Ethernet Smart Switch.
Following the installation instructions should be quick and easy. If you run into
problems, please refer to the Troubleshooting section of this guide. If you need
further technical support, please visit www.TRENDNET.com or call technical
support by phone.
Verify Package Contents
Please make sure you have everything in the box:
1
1. Prepare for Installation
English QIG
English
TPE-S88
AC Power Cord
Quick Installation Guide
CD-ROM
4 rubber shock cushions
2 mounting brackets
with screws
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
TPE-S88
Version 01.07.05
Power-over-Ethernet Smart Switch
Quick Installation Guide
Commutateur intelligent Power-over-Ethernet
Guide d'installation rapide
PoE-Smart-Switch
Kurzanleitung zur Installation
Guía de instalación rápida de
conmutador inteligente de Power-over-Ethernet (PoE)
2
2. Product Detail
The TPE-S88 has eight 10/100Mbps Power-over-Ethernet ports and eight
10/100Mbps ports. It also has 5 types of LED that indicate power, CPU
operation, network activity, data transfer rate, and Power-over-Ethernet status.
English
CPU
Operation
Power
Data
Transfer
Rate
Network
Activity
Power-over-
Ethernet Status
10/100 Mbps
Power-over-
Ethernet Ports
10/100 Mbps
Ports
3
English
Connect the power cord to the TPE-S88 and plug the power cord into an
available power outlet.
3. Hardware Installation
4
English
4. Configure the Power-Over-Ethernet
Web Smart Switch
Note: For MAC Users, change your computers IP address to
192.168.0.X (where X is an available number from 1-253), and enter
192.168.0.1 in your web browser to access the Print Server's Web
Utility.
1. Insert the TPE-S88 CD-ROM into your computer's CD-ROM drive.
2. Click Start Run. Type d:\Web-Management Utility\setup.exe . If your
CD-ROM uses a different letter than d, then use a different letter
(i.e. e:\Web-Management Utility\setup.exe).
3. Click Next.
4. Click Next.
For Windows Users
5
English
5. Click Next.
6. Click Next.
7. Click OK.
6
English
8. Click Start All Programs web_management_utility. Click the
web_management_utility icon.
9. Click Discovery. Select the discovered switch and click Configuration
setting.
10. Type in the IP address that applies to your existing network. Type in the
Default Gateway (i.e. your router's local IP address). Type in a Password
and Click Set.
11. Double-click the selected switch.
12. On the Monitor List, double-click the selected switch.
English
7
13. Type in your password. Click Login.
For more information in using all the web smart features, please consult the
user's guide.
English
8
9
Technical Support Hours
7:00AM ~ 6:00PM, Monday through Friday
Pacific Standard Time (except holidays)
Contact Technical Support
Telephone: +1-310-626-6252
Fax: +1-310-626-6267
Website: www.TRENDNET.com
E-mail: [email protected]
Troubleshooting
Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
Q5:
A5:
After connecting the TPE-S88 to a power outlet, the LEDs do not turn on?
Please check the following connections:
1. Double check the connection of the power cord to the TPE-S88.
2. Double check the connection of the power cord to the power outlet.
3. Double check that the power outlet is receiving power.
When I access the TPE-S88 using a web browser, I get a screen that tells me “only
one user can login”. What do I do?
Another computer is configuring the TPE-S88. Please wait until the user logs off.
After the user logged off from the web configuration page, I try to login into the
TPE-S88, but I still get a screen that tells me “only one user can login.”
Disconnect the power cord from the TPE-S88. Wait for 5 seconds and
reconnect the power cord to the TPE-S88. Allow another 3-5 seconds for the
switch to power on. Now attempt to access the web configuration page to login.
When I connect a computer to the switch's port, the LINK/ACT LED turns on, but
the 100Mbps LED remains off.
When the 100Mbps LED remains off, the computer's connection speed is
10Mbps. Please consult the User's guide in the CD-ROM for more information.
I connect a PoE device into the switch's PoE port, but the PoE Status LED remains
off.
Please check the following connections:
1. Make sure that the CAT 5 cable is properly inserted into the PoE port.
2. Make sure that the CAT5 cable is properly inserted into a PoE device.
If you have further questions, please contact Trendware's Technical Support Department.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received including interference that may cause undesired operation.
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.
TRENDnet
TRENDware, USA
What's Next in Networking
@
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDware’s website at http://www.TRENDNET.com
TRENDware International, Inc.
3135 Kashiwa Street
Torrance, CA 90505
http://www.TRENDNET.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Trendnet TPE-S88 Owner's manual

Trendnet
Brand
Trendnet
Model
TPE-S88
Category
Network switches
Type
Owner's manual

Trendnet TPE-S88 is an advanced networking device that combines the functionality of a switch and a power over Ethernet (PoE) injector. It is equipped with 8 10/100Mbps Power-over-Ethernet ports and 8 10/100Mbps ports, allowing you to connect various network devices such as computers, IP cameras, VoIP phones, and access points.

The PoE ports on the TPE-S88 can provide power to compatible devices, eliminating the need for separate power cables. This makes it ideal for powering devices in locations where it may be difficult or inconvenient to run additional cabling, such as on ceilings or in remote areas.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents