Zanussi ZWH7100P User manual

User manual

Washing Machine

ZWH 7100 P

ZWH 7120 P

Contents

Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2

Frost precaution _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4

Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4

Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5

Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6

Special accessories _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10

First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10

Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10

Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11

Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 18

Consumption values _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 21

Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 21

What to do if… _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 23

Subject to change without notice

Safety information

Important! Read carefully and keep for future reference.

• The safety of your appliance complies with the industry

standards and with legal requirements on the safety of

appliances. However, as manufacturers, we feel it is

our duty to provide the following safety notes.

• It is most important that this instruction book should

be retained with the appliance for future reference.

Should the appliance be sold or transferred to another

owner, or should you move house and leave the appli-

ance, always ensure that the book is supplied with the

appliance in order that the new owner can get to know

the functioning of the appliance and the relevant warn-

ings.

• You MUST read them carefully before installing or us-

ing the appliance.

• Before first starting up, check the appliance for any

damage incurred during transport. Never connect up a

damaged appliance . If parts are damaged, contact your

supplier.

• If the appliance is delivered in the winter months when

there are minus temperatures. Store it at room temper-

ature for 24 hours before using for the first time.

• This appliance is made for use in a normal domestic

situation. The manufacturer is not responsible for

freezing damages. Read "Frost precaution".

General safety

• It is dangerous to alter the specifications or attempt to

modify this product in any way.

• During high temperature wash programmes the door

glass may get hot. Do not touch it!

• Make sure that small children and pets do not climb

into the drum. To avoid this, please check inside the

drum before using.

• Any objects such as coins, safety pins, nails, screws,

stones or any other hard, sharp material can cause ex-

tensive damage and must not be placed into the appli-

ance.

• Only use the advised quantities of fabric softener and

detergent. Damage to the fabric can ensue if you over-

fill. Refer to the manufacturer’s recommendations of

quantities.

• Wash small items such as socks, laces, washable belts

etc in a washing bag or pillow case as it is possible for

such items to slip down between the tub and the inner

drum.

• Do not use your appliance to wash articles with whale-

bones, material without hems or torn material.

• Always unplug the appliance and turn off the water

supply after use, cleaning and maintenance.

• Under no circumstances should you attempt to repair

the appliance yourself. Repairs carried out by inexper-

ienced people may cause injury or serious malfunc-

tioning. Contact your local Service Centre. Always in-

sist on genuine spare parts.

Installation

• This appliance is heavy. Care should be taken when

moving it.

• All packing and transit bolts must be removed before

use. Serious damage can occur to the product and to

property if this is not adhered to. See relevant section

in the user manual.

• This appliance is free standing only. DO NOT build it in

under a counter and DO NOT remove the worktop for

any reason.

• After having installed the appliance, check that it is not

standing on the inlet and drain hose and the worktop is

not pressing the electrical supply cable against the

wall.

• Install the appliance on a flat hard floor.

• Never place cardboard, wood or similar materials un-

der the appliance to compensate for any unevenness in

the floor.

• If the appliance is situated on a carpeted floor, please

adjust the feet in order to allow air to circulate freely

under the appliance.

• Check that the appliance does not touch the wall or

other kitchen units.

• This appliance must be connected to a cold water sup-

ply.

• Do not use the hose from your previous appliance to

connect to water supply. Always use the hose supplied

with the appliance.

• The inlet hose must not be lengthened. If it is too short

and you do not wish to move the tap, you will have to

purchase a new, longer hose specially designed for

this type of use.

• Always be sure, that there is no water leakage from ho-

ses and their connections after the installation.

• If the appliance is installed in a location subject to

frost, please read the “Frost precaution” chapter. Man-

ufacturer decline any responsibility for freezing dam-

ages.

• Any plumbing work required to install this appliance

should be carried out by a qualified plumber or compe-

tent person.

• Any electrical work required to install this appliance

should be carried out by a qualified electrician or com-

petent person.

Use

• This appliance is designed for domestic use. It must

not be used for purposes other than those for which it

was designed.

• Only wash fabrics which are designed to be machine

washed. Follow the instructions on each garment label.

• Do not overload the appliance. See the "Washing Pro-

gramme Chart".

• Before washing, ensure that all pockets are empty and

buttons and zips are fastened. Avoid washing frayed or

torn articles and treat stains such as paint, ink, rust,

and grass before washing. Underwired bras must NOT

be machine washed.

• The detergent dispenser drawer is provided with an in-

sert for liquid detergent. Do not use the insert down-

wards for gelatinous detergents, with programmes in-

cluding prewash, with the delay start option. In all

these cases you can use metering balls or sachets pro-

vided with the detergent, Take out the metering aid at

the end of the washing cycle.

• Garments which have been in contact with volatile pe-

troleum products should not be machine washed. If

volatile cleaning fluids are used, care should be taken

to ensure that the fluid is removed from the garment

before placing in the appliance.

• Never pull the power supply cable to remove the plug

from the socket; always take hold of the plug itself.

• Never use the appliance if the power supply cable, the

control panel, the working surface or the base are dam-

aged so that the inside of the appliance is accessible.

Child safety

• This appliance is not intended for use by persons (in-

cluding children) with reduced physical sensory or

mental capabilities or lack of experience and knowl-

edge unless they have been given supervision or in-

struction concerning use of the appliance by a person

responsible for their safety.

• Children should be supervised to ensure that they do

not play with the appliance.

• The packaging components (e.g. plastic film, polystyr-

ene) can be dangerous to children - danger of suffoca-

tion! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• Make sure that children or pets do not climb inside the

drum. To prevent children and pets becoming trapped

inside the drum this appliance incorporates a special

feature.

To activate this device, ro-

tate the button (without

pressing it) inside the

door clockwise until the

groove is horizontal. If

necessary use a coin.

To disable this device and

restore the possibility of

closing the door, rotate the

button anti-clockwise until

the groove is vertical.

Frost precaution

If the appliance is installed in a place where the tempera-

ture could drop below 0°C, proceed as follows to remove

any water remaining inside the appliance:

1. unplug the appliance;

2. turn off the water tap;

3. unscrew the water inlet hose from the tap;

4. unscrew the drain hose from the rear support and

unhook it from sink or spigot;

5. place a bowl on the floor;

6. let the drain hose run along the floor, place the ex-

ternal extremities of the drain and inlet hoses in the

bowl placed on the floor and let water drain out com-

pletely;

7. screw the water inlet hose to the tap and the drain

hose to the rear of the appliance again;

When you intend to start the appliance up again, make

sure that the room temperature is above 0°C.

Environment concerns

The symbol on the product or on its packaging

indicates that this product may not be treated as

household waste. Instead it should be taken to the

appropriate collection point for the recycling of electrical

and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by inappropriate

waste handling of this product. For more detailed

information about recycling of this product, please contact

your local council, your household waste disposal service

or the shop where you purchased the product.

Packaging materials

The materials marked with the symbol are recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Ecological hints

To save water, energy and to help protect the environment,

we recommend that you follow these tips:

• Normally soiled laundry may be washed without pre-

washing in order to save detergent, water and time (the

environment is protected too!).

• The machine works more economically if it is fully loa-

ded.

• With adequate pre-treatment, stains and limited soiling

can be removed; the laundry can then be washed at a

lower temperature.

• Measure out detergent according to the water hard-

ness, the degree of soiling and the quantity of laundry

being washed.

Product description

1 2 3

Detergent dispenser drawer

Worktop

Control panel

Door opening handle

Rating plate (on the inner edge)

Front adjustable feet

Water drain hose

Drain hose support

Hose holders

Water inlet hose

Mains cable

Back feet

ZWH 7100 P = 2 front adjustable feet ZWH 7120 P = 4 adjustable feet

Technical data

Dimensions Width

Height

Depth

60 cm

85 cm

54 cm

Electrical connection Information on the electrical connection is given on the rating plate, on the

inner edge of the appliance door.

Water supply pressure Minimum

Maximum

0,05 MPa

0,8 MPa

Maximum Load Cotton 7 kg

Spin Speed Maximum 1000 rpm (ZWH 7100 P)

1200 rpm (ZWH 7120 P)

Installation

Unpacking

Warning!

• Read carefully the "Safety information" chapter

before installing the appliance.

x 3

x 2

x 1

Warning! Remove and keep all transit devices so

that they can be refitted if the appliance ever has

to be transported again.

Necessary tools

10 mm

30 mm

• Remove the external

film. Use a cutter, if

necessary.

• Remove the cardboard top.

• Remove the polystyrene packaging materials.

• Spread the front piece

on the floor behind the

appliance and then lay

the appliance carefully

rear side down on it.

Make sure that no ho-

ses are crushed in the

process.

• Remove the polystyrene base from the bottom.

• Return appliance to it's

upright position.

• Open the door and re-

move the plastic hose

guide, the bag contain-

ing the instruction

booklet and the plastic

plug caps from the

drum.

• Remove the power supply cable and the draining and

inlet hose from the hose holders (C) on the rear of

the appliance.

• Unscrew the three bolts (A) and remove the hose

holders (C).

• Slide out the relevant plastic spacers (B).

Warning! Do not re-

move the drain hose

from the rear support. Re-

move this hose only if it is

necessary to drain the wa-

ter. Refer to "Frost precau-

tion" and "What to do if".

• Plug the smaller upper hole and the two large ones

with the corresponding plastic plug caps.

Positioning and levelling

Level the appliance by raising or lowering the feet. De-

pending on the model, the appliance can have four ad-

justable feet, or two front-adjustable feet and two back

fixed feet.

The appliance MUST be level and stable on a flat hard

floor. If necessary, check the setting with a spirit level.

Any necessary adjustment can be made with a spanner.

Accurate levelling prevents vibration, noise and dis-

placement of the appliance during operation.

Repeat the levelling action, if the appliance is not level

and stable.

Water inlet

Connect the hose to a tap

with a 3/4” thread.

35°

45°

Loosen the ring nut to angle the hose to the left or right

depending on the position of your water tap. Do not

place the inlet hose downwards. After positioning the

inlet hose, be sure to tighten the ring nut again to pre-

vent leaks.

Water drainage

Firstly form a hook in the end of the drain hose using

the plastic hose guide supplied with the appliance .

The end of the drain hose can be positioned in four

ways:

• Hooked over the edge of a sink using the plastic

hose guide.

Tie the plastic hose guide to the tap with a string to pre-

vent that the drain hose unhooks when the appliance is

emptying.

• Onto a sink outlet spigot.

Push the drain hose onto the spigot and secure with a

clip, ensure a loop is formed in the drain hose to pre-

vent waste from the sink entering the appliance.

If the outlet spigot has not been used before, remove

any blanking plug that may be in place.

• Directly into a drain pipe at a height of not less than

60 cm and not more than 100 cm.

MAX 100cm

The end of the drain hose

must always be ventilated,

i.e. the inside diameter of

the drain pipe must be

larger than the outside di-

ameter of the drain hose.

The drain hose must not

be kinked.

• Directly to a built-in drain pipe in the room wall.

The drain hose may be extended to a maximum of 4

metres. An additional drain hose and joining piece

is available from your Local Centre.

Connections overview

115 cm 140 cm

mc150mc100

max 100 cm

min. 60 cm

max 100 cm

min. 60 cm

mc9 0 mc115

Electrical connection

• The appliance must be earthed.

• Make sure that the electrical information on the rating

plate agree with your domestic power supply.

• Always use a correctly installed shockproof socket.

• Do not use multi-way plugs, connectors and extension

cables. There is a risk of fire.

• Do not replace or modify the mains cable yourself.

Contact the After Sales Service.

• Make sure that the mains plug and cable is not

squashed or damaged by the back of the appliance.

• Make sure that the mains plug is accessible after in-

stallation.

• Do not pull the mains cable to disconnect the appli-

ance. Always pull the mains plug.

• This appliance complies with the E.E.C. Directives.

Special accessories

Rubber feet kit (4055126249)

Available from your authorized dealer.

The rubber feet are particularly recommended on floating,

slippery and wooden floors.

Mount the rubber feet to prevent vibration, noises and dis-

placement of the appliance during operation.

Read carefully the instructions supplied with the kit.

First use

• Ensure that the electrical and water connections

comply with the installation instructions.

• Ensure that the drum is empty.

• Before the first wash, run a cotton cycle at the

highest temperature without any laundry in the

machine, to remove any manufacturing residue

from the drum and tub. Pour 1/2 a measure of

detergent into the main wash compartment and

start the machine.

Personalisation

Buzzer

The appliance is provided with an acoustic device, which

sounds in the following cases:

• at the end of the cycle;

• if there is a fault.

By pressing the 4 and 5

buttons simultaneously for

about 6 seconds, the

acoustic signal is deacti-

vated (except if there is a

fault).

By pressing these 2 buttons again, the acoustic signal

is reactivated.

Child safety lock

This device permits you to leave the appliance unattended

so you do not need to worry that children might be injured

by or cause damage to the appliance. This function re-

mains enabled also when the appliance is not working.

There are two different ways to set this option:

1. Before pressing button 9: it will be impossible to

start the appliance.

2. After pressing button 9: it will be impossible to

change any other programme or option.

To enable or disable this

option press simultane-

ously for about 6 seconds

buttons 2 and 3 until on

the display, the icon

appears or disappears.

Daily use

Sort out the laundry

Follow the wash code symbols on each garment label and

the manufacturer’s washing instructions. Sort the laundry

as follows: whites, coloureds, synthetics, delicates, wool-

lens.

Before Loading The Laundry

Important! Make sure that

no metal objects are left in

the laundry (e.g. hair clips,

safety pins, pins). Button

up pillowcases, close zip

fasteners, hooks and pop-

pers. Tie any belts or long

tapes. Remove any hooks

(e.g curtains).

• Never wash whites and coloureds together. Whites may

lose their «whiteness» in the wash.

• New coloured items may run in the first wash; they

should therefore be washed separately the first time.

• Rub particularly soiled areas with a special detergent or

detergent paste.

• Treat curtains with special care.

• Wash the socks and the gloves inside the bag or a net.

Remove stubborn stains before washing:

Blood: treat fresh stains with cold water. For dried stains,

soak overnight in water with a special detergent then rub

in the soap and water.

Oil based paint: moisten with benzine stain remover, lay

the garment on a soft cloth and dab the stain; treat several

times.

Dried grease stains: moisten with turpentine, lay the gar-

ment on a soft surface and dab the stain with the fingertips

and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust removing

product used cold. Be careful with rust stains which are

not recent since the cellulose structure will already have

been damaged and the fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites and fast

coloureds only).

Grass: soap lightly and treat with bleach (whites and fast

coloureds only).

Ball point pen and glue: moisten with acetone

, lay the

garment on a soft cloth and dab the stain.

Lipstick: moisten with acetone as above, then treat stains

with methylated spirits. Treat any residual marks with

bleach.

Red wine: soak in water and detergent, rinse and treat with

acetic or citric acid, then rinse. Treat any residual marks

with bleach.

Ink: depending on the type of ink, moisten the fabric first

with acetone

, then with acetic acid; treat any residual

marks on white fabrics with bleach and then rinse thor-

oughly.

Tar stains: first treat with stain remover, methylated spirits

or benzine, then rub with detergent paste.

Open the door by carefully pulling the door handle

outwards

Load the laundry

Place the laundry in the

drum, one item at a time,

shaking them out as much

as possible.

Maximum Loads

Recommended loads are indicated in the «Wash-

ing Programmes».

General rules:

• Cotton, linen: drum full but not too tightly packed;

• Synthetics: drum no more than half full;

• Delicate fabrics and woollens: drum no more than one

third full.

1) do not use acetone on artificial silk.

Close the door gently

Warning! Make sure

that any fabrics were

not trapped when closing

the door.

Detergents and additives

Good washing results also depend on the choice of deter-

gent and use of the correct quantities to avoid waste and

protect the environment.

Although biodegradable, detergents contain substances

which, in large quantities, can upset the delicate balance

of nature.

The choice of detergent will depend on the type of fabric

(delicates, woollens, cottons, etc.), the colour, washing

temperature and degree of soiling.

All commonly available washing machine detergents may

be used in this appliance:

• powder detergents for all types of fabric,

• powder detergents for delicate fabrics (40°C max) and

woollens,

• liquid detergents, preferably for low temperature wash

programmes (60°C max) for all types of fabric, or spe-

cial for woollens only.

Quantity of detergent to be used

The type and quantity of detergent will depend on the type

of fabric, load size, degree of soiling and hardness of the

water used.

For the quantity of detergent, refer always to what is writ-

ten on the product packing.

Use less detergent if:

• you are washing a small load,

• the laundry is lightly soiled,

• large amounts of foam form during washing.

Degrees of water hardness

Water hardness is classified in so-called “degrees” of

hardness. Information on hardness of the water in your

area can be obtained from the relevant water supply com-

pany, or from your local authority.

If the water hardness degree is medium or high we sug-

gest you to add a water softener following always the

manufacturer’s instructions.

When the degree of hardness is soft, readjust the quantity

of the detergent.

Open the detergent dispenser drawer

Compartment for

powder or liquid detergent

used for main wash.

Compartment for liquid

additives (fabric softener,

starch).

Warning! If you wish to carry out the prewash, pour

the detergent among washing items into the drum.

Warning! Depending on the type detergent you use

(powder of liquid), ensure that the flap, placed in the

main wash compartment, is in the desired position.

Flap for powder or liquid detergent

UP- Flap position if using

POWDER detergent

DOWN - Flap position if

using LIQUID detergent

during main wash

PUSH

If the flap is not in the desired position:

• Remove the drawer. Push the drawer edge outwards

where indicated by the arrow (PUSH) to facilitate

drawer removal.

The flap is down and you wish to use powder detergent:

• Rotate the flap up-

wards. Ensure to fit the

flap completely in.

• Carefully put the drawer

back.

• Measure out the deter-

gent.

• Pour the powder deter-

gent into the main wash

compartment

The flap is up and you wish to use liquid detergent:

• Rotate the flap down-

wards.

• Carefully put the drawer

back.

• Measure out the detergent.

For the quantity of detergent, refer always to what

is written on the product packing and ensure that

the detergent can be poured in the drawer.

•

Pour the liquid detergent in the compartment

without exceeding the limit indicated in the flap. The

detergent must be placed in the appropriate com-

partments of the dispenser drawer before starting the

wash programme.

Warning! Do not use the flap in "DOWN" position

with:

• Gelatinous detergent or thick detergent.

• Powder detergent.

• With programmes with prewash.

• Do not use liquid detergent if the washing programme

doesn't start immediately.

In all above listed cases, use the flap in "UP" posi-

tion .

Measure out the fabric softener

Pour fabric softener or any

additives into the compart-

ment marked

(do not

exceed the «MAX» mark

in the drawer). Any addi-

tives must be placed in the

appropriate compartments

of the dispenser drawer

just before starting the

wash programme.

Close the detergent dispenser drawer

Set your washing programme

The control panel permits to select a washing programmes and different options.

When an option button is selected, the corresponding pilot light is on. Otherwise it is off.

For compatibility among washing programmes and options, see the "Washing Programmes". If an incorrect op-

tion is selected, the integrated red pilot light of the button 9 flashes 3 times and the display shows the message

Err.

1 2 3 4 5 6 9

7 8

Programme selector dial Turn the programme selector dial to the required programme. The selector

dial can be turned either clockwise or counter-clockwise. The green pilot

light of the button 9 starts flashing: the appliance is now switched on.

If you turn the programme selector dial to another programme when

the appliance is working, the red pilot light of the button 9 will flash 3

times and the message Err is displayed to indicate a wrong selection. The

appliance will not perform the new selected programme.

• To switch the appliance off, turn the programme selector dial to the posi-

tion

• To cancel or change a running programme, switch the appliance off by

turning the programme selector dial to the position

. Select the new

programme by turning the selector to the desired programme. Start the

new programme by pressing the button 9 again. The water in the tub will

be not emptied out.

Temperature button

95°

60°

40°

30°

Push the temperature button to select the most suitable temperature for

washing your laundry.

: Cold wash

Spin reduction

900

1200

700

By selecting a programme, the appliance proposes automatically the maxi-

mum spin speed provided for that programme.

Press this button repeatedly to change the spin speed, if you want your

laundry to be spun at a different speed. The relevant light illuminates.

Rinse Hold By pressing this button the corresponding pilot light illuminates.

By selecting this function the water of the last rinse is not emptied out to

prevent the fabrics from creasing. Before opening the door it will be neces-

sary to empty out the water.

To empty out the water, please read the paragraph «At the end of the pro-

gramme».

Super Quick By pressing this button the corresponding pilot light illuminates.

Short cycle for lightly soiled items or for laundry which needs only freshen-

ing up.

With this option, a reduced load of laundry is recommended:

• Cottons 3,5 kg

• Synthetics and delicates 2 kg

Extra Rinse This appliance is designed to save energy. If it necessary to rinse the laun-

dry using an extra quantity of water (extra rinse), select this option. Some

additional rinses will be performed. This option is recommended for people

who are allergic to detergents, and in areas where the water is very soft.

Display

7.1

7.2

7.3

The display shows the following information:

7.1 Delay Start icon

7.2 Child safety lock

This device permits you to leave the appliance unattended during it's func-

tioning.

7.3

• Duration of the selected programme

After selecting a programme, the duration is displayed in hours and mi-

nutes (for example

). The duration is calculated automatically on

the basis of the maximum recommended load for each type of fabric. Af-

ter the programme has started, the time remaining is updated every mi-

nute.

•Delayed start

The selected delay set by pressing the relevant button appears on the

display for a few seconds, then the duration of the selected programme is

displayed again. The delay time value decreases by one unit every hour

and then, when 1 hour remains, every minute.

• Alarm codes

In the event of operating problems, some alarm codes can be displayed,

for example

(see paragraph «What to do if...»).

•Incorrect option selection

If an option which is not compatible with the set wash programme is se-

lected, the message Err is displayed at the bottom of the display for a few

seconds and the integrated red light of button 9 start flashing.

• End of programme

When the programme has finished a zero (

) is displayed, the door

pilot light 10 and the pilot light of button 9 go out and the door can be

opened.

Delay Start The programme can be delayed from 30 min - 60 min - 90 min, 2 hours and

then by 1 hour up to a maximum of 20 hours by means of this button.

Before you start the programme, if you wish to delay the start, press this

button to select the desired delay.

The selected delay time value will appear on the display for a few seconds,

then the duration of the programme will appear again.

You must select this option after you have set the programme and before

you start the programme.

You can cancel or modify the delay time at any moment, before you press

button 9.

Selecting the delay start:

• Select the programme and the required options.

• Select the delay start by pressing button 8.

• Press button 9:

– the appliance starts its hourly countdown.

– the programme will start after the selected delay has expired.

Cancelling the Delay Start after having started the programme:

• Set the appliance to PAUSE by pressing button 9.

•

Press button 8 once. On the display will appear

• Press button 9 again to start the programme.

• The selected delay can be changed only after selecting the washing

programme again.

• The door will be locked throughout the delay time. If you need to

open the door, you must first set the appliance to PAUSE by press-

ing button 9 and wait a few minutes before opening the door. After

you have closed the door, press the same button again.

The Delay Start cannot be selected with the draining programme.

Start/Pause Start the programme by pressing the button 9

•To start the selected programme, press the button 9, the corresponding

green pilot light stops flashing. The pilot light 10 illuminates to indicate

that the appliance starts operating and the door is locked. If you have

chosen a delayed start, the appliance will begin the countdown.

•To interrupt a programme which is running, press the button 9: the cor-

responding green pilot light starts flashing. It is possible to change some

options of a running programme before the programme carries them out.

•To restart the programme from the point at which it was interrupted,

press the button 9.

• After the programme has started the door is locked. If, for any reason,

you need to open the door, set firstly the appliance to PAUSE by pressing

the button 9. After a few minutes it will be possible to open the door.

If the door remains locked, this means that the appliance is already heat-

ing or that the water level is too high. In any case, do not try to force the

door!

If you cannot open the door but you need to open it you have to switch

the appliance off by turning the selector dial to

. After a few minutes

the door can be opened (pay attention to the water level and tempera-

ture!). After closing the door, it is necessary to select the programme and

options again and to press the button 9.

Door light The pilot light 10 illuminates when the programme starts and indicates if the

door can be opened:

• light on: the door cannot be opened. The appliance is working or has

stopped with water left in the tub.

• light off: the door can be opened. The programme is finished or the water

has been emptied out.

• light blinking: the door is opening in a few minutes.

At the end of the programme

The appliance stops automatically. The pilot light of the

button 9 and the pilot light 10 go off. The display shows

If a programme or an option that ends with water left in the

tub has been selected, the pilot light 10 remains on and

the door is locked to indicate that the water must be emp-

tied out before opening the door.

Follow the below instructions to empty out the water:

•

Turn the programme selector dial to

• Select the draining or spinning programme.

• Reduce the spin speed if needed, by pressing the rele-

vant button.

• Press the button 9.

At the end of the programme, the door can be now

opened. Turn the programme selector dial to

to switch

the appliance off.

Remove the laundry from the drum and carefully check

that the drum is empty. If you do not intend to carry out

another wash, close the water tap. Leave the door open to

prevent the formation of mildew and unpleasant smells.

Warning! If there are children or pets in the house,

activate the child safety device in the inner side of

the door frame (for more details read " Child safety" in the

chapter "Safety Information").

Stand by : during programme setting up and once the pro-

gramme has finished, if the programme selector dial and

any button are not touched, after a few minutes the energy

saving system is enabled. The pilot lights and the display

go off. The green pilot light of the button 9 flashes with a

low frequency. By pressing any button the appliance will

come out of the energy saving status.

Door seal

At the end of every cycle,

check from the door seal

and remove objects that

could be trapped in the

fold.

Washing programmes

Programme - Maximum and Minimum Temperature - Cycle De-

scription - Maximum Spin Speed - Maximum Fabrics Load - Type

of Laundry

Options

Detergent Com-

partment

COTTONS

95°-

(Cold)

Main wash - Rinses - Maximum spin speed: 1000 rpm for

ZWH7100P - 1200 rpm for ZWH7120P

Max. load 7 kg - Reduced load 3,5 kg

White, coloured cotton and linen. Normally soiled items.

SPIN REDUCTION,

RINSE HOLD,

SUPER QUICK

EXTRA RINSE,

DELAY START

+ COTTON WITH PREWASH

95° -

(Cold)

Prewash - Main wash - Rinses - Maximum spin speed: 1000 rpm

for ZWH7100P - 1200 rpm for ZWH7120P

Max. load 7 kg - Reduced load 3,5 kg

White, coloured cotton and linen. Heavy soiled items.

SPIN REDUCTION,

RINSE HOLD

SUPER QUICK

EXTRA RINSE

DELAY START

Programme - Maximum and Minimum Temperature - Cycle De-

scription - Maximum Spin Speed - Maximum Fabrics Load - Type

of Laundry

Options

Detergent Com-

partment

ECO

60° - 40°

Main wash - Rinses - Maximum spin speed: 1000 rpm for

ZWH7100P - 1200 rpm for ZWH7120P

Max. load 7 kg

White and coloured cotton. This programme can be selected for

slightly or normally soiled cotton items. The temperature will de-

crease and the washing time will be extended. This allows to obtain

a good washing efficiency by saving energy.

SPIN REDUCTION,

RINSE HOLD,

EXTRA RINSE,

DELAY START

SYNTHETICS

60° -

(Cold)

Main wash - Rinses - Maximum spin speed at: 1000 rpm for model

ZWH 7100 P; 1200 rpm for model ZWH 7120 P

Max. load 3,5 kg - Reduced load 2 kg

Synthetic or mixed fabrics: underwear, coloured garments, non-

shrink shirts, blouses . Normally soiled items.

SPIN REDUCTION,

RINSE HOLD

SUPER QUICK

EXTRA RINSE,

DELAY START

MIX

(Cold)

Main wash - Rinses - Maximum spin speed at: 1000 rpm for model

ZWH 7100 P; 1200 rpm for model ZWH 7120 P

Max. load 3,5 kg

Highly energy efficient cold wash programme for lightly soiled

laundry. This programme requires a detergent which is active in

cold water.

SPIN REDUCTION,

RINSE HOLD,

EXTRA RINSE,

DELAY START

DELICATES

40°-

(Cold)

Main wash - Rinses - Maximum spin speed at 700 rpm

Max. load kg 3,5 - Reduced load 2 kg

Delicate fabrics: acrylics, viscose, polyester . Normally soiled

items.

RINSE HOLD,

SUPER QUICK

EXTRA RINSE,

DELAY START

WOOL / HANDWASH

40°-

(Cold)

Main wash - Rinses - Maximum spin speed: at 1000 rpm for model

ZWH 7100 P; 1200 rpm for model ZWH 7120 P

Max. load 2 kg

Machine washable wool, hand washable woollens and delicate fab-

rics with «hand washing» care symbol. Note: A single or bulky item

may cause imbalance. If the appliance doesn’t perform the final spin

phase, add more items, redistribute the load manually and then se-

lect the spinning programme.

SPIN REDUCTION,

RINSE HOLD,

DELAY START

Programme - Maximum and Minimum Temperature - Cycle De-

scription - Maximum Spin Speed - Maximum Fabrics Load - Type

of Laundry

Options

Detergent Com-

partment

RINSE

Rinse - Short spin speed 700 rpm. If a spin speed higher than 700

rpm is selected, by pressing the relevant button, the appliance per-

forms a long spin. (Maximum spin speed: 1000 rpm for ZWH7100P

- 1200 rpm for ZWH7120P)

Max. load 7 kg

To rinse and spin cotton garments which have been washed by

hand. Select the EXTRA RINSE option to intensify the rinsing ac-

tion. The appliance adds additional rinses.

SPIN REDUCTION,

RINSE HOLD,

EXTRA RINSE,

DELAY START

DRAIN

Draining of water

For emptying out the water left in the drum.

SPIN

Drain and long spin at maximum spin speed: 1000 rpm for

ZWH7100P - 1200 rpm for ZWH7120P

Max. load 7 kg

Separate spin for hand washed garments and after programmes

with the Rinse Hold option selected. You can choose the spin speed

by pressing the relevant button to adapt it to the fabrics to be spun.

If a spin speed at 700 rpm is selected, by pressing the relevant but-

ton, the appliance performs a short spin.

SPIN REDUCTION,

DELAY START

Special programmes

EASY IRON

60°-

(Cold)

Main wash - Rinses - Maximum spin speed at 900 rpm

In order to obtain the best anti-creasing result, reduce the load of

synthetic items. (Recommended load 1,5 kg)

Synthetic or mixed fabrics. Gentle wash and spin to avoid any

creasing. The appliance performs additional rinses.

SPIN REDUCTION,

RINSE HOLD,

EXTRA RINSE

DELAY START

BLANKET

30°

Main wash - Rinses - Maximum spin speed at 700 rpm

Special program for one sleeping bag, one duvet or washable coats

padded with synthetic filling or dawns. The Extra Rinse option is

activated automatically.

DELAY START

MINI 30

30°

Main wash - Rinses - Maximum spin speed at 700 rpm

Max. load 3 kg

Synthetics and delicates. Lightly soiled items or which only needs

freshening up.

DELAY START

Page is loading ...

Zanussi ZWH7100P User manual

Related papers

Other documents