M-system CLSP User manual

Brand: M-system

Model: CLSP

Type: User manual

M-system CLSP

The M-system CLSP is a clamp-on pulse sensor designed for indoor use in environments with temperatures ranging from 0 to 55°C (32 to 131°F) and relative humidity within 80% RH. It has a power input rating of 12V DC and an operational range of 12V ±10%, with a maximum current draw of 5mA.

The CLSP is designed to be mounted on a wall using the provided mounting holes. It features a terminal cover that can be removed to connect wires according to the provided connection diagram. The input cable is connected by squeezing the levers on both sides of the top section to detach the tabs and pulling out the top section. The input cable is then placed in the indicated position and the top section is put back and bound over the tabs/levers with a binding strap.

M-system CLSP

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■ PACKAGE INCLUDES:

Clamp-on pulse sensor ........................................................(1)

■ MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■ POWER INPUT RATING & OPERATIONAL RANGE

•Locate the power input rating marked on the product and

conﬁrm its operational range as indicated below:

12V DC rating: 12V ±10%, max. 5mA

■ GENERAL PRECAUTIONS

•Before you remove the module or mount it, turn off the

power supply and input signal for safety.

■ ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the air,

install the module inside proper housing with sufﬁcient

ventilation.

•Do not install the module where it is subjected to continu-

ous vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within 0 to 55°C (32

to 131°F) with relative humidity within 80% RH in order

to ensure adequate life span and operation.

■ WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■ AND ....

•The module is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required

for satisfying complete performance described in the data

sheet.

COMPONENT IDENTIFICATION

Terminal Cover

(separable)

Specifications

*Binding strap here

Tab

BodyInput Cable

Lever

Top Section

INSTALLATION

■ MOUNTING THE MODULE

1) Remove the terminal cover and connect wires according

to the connection diagram. Be aware of the wire inser-

tion direction (See ‘Inserting Wires’).

2) Put the terminal cover back so that its keys meet the key

holes. Be aware of the cover direction.

12V

Terminal Cover

Key

Terminal Cover

Key Hole

Mounting Hole

3) Tighten screws using the mounting holes to ﬁx the mod-

ule on a wall.

■ CONNECTING THE INPUT CABLE

1) Squeeze the levers on both sides to detach the tabs and

pull out the top section.

2) Place the input cable to the position indicated on the

above drawing.

3) Put back the top section and bind over the tabs/levers

with a binding strap.

CLAMP-ON PULSE SENSOR

MODEL

CLSP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

EM-9237 Rev.3 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■ EXTERNAL DIMENSIONS unit: mm (inch)

49.1 (1.93)

33 (1.30)

39 (1.54)

34 (1.34)

28 (1.10)

22 (.87)

2–3.5 dia. MTG HOLE

(.55)

79 (3.11)

5 (.20) dia.

3–M3 SCREW

TERMINAL COVER

12V

■ CONNECTION DIAGRAM

12V

CLSP

PULSE INPUT

–

POWER SUPPLY

PULSE OUTPUT

WIRING INSTRUCTIONS

■ SOLDERLESS TERMINAL unit: mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.75 mm

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

■ INSERTING WIRES

Insert the output and power supply wires from the direction

as shown below and tighten ﬁrmly (torque 0.5 N·m).

12V

CHECKING

1) Terminal wiring: Check that all cables are correctly con-

nected according to the connection diagram.

2) Power input voltage: Check voltage across the terminal

12V – R0 with a multimeter.

3) Input: Check the input signal.

4) Output: Check the output signal.

LIGHTNING SURGE PROTECTION

M-System offers a series of lightning surge protector for

protection against induced lightning surges. Please contact

M-System to choose appropriate models.

CLSP

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: inf[email protected].jp

EM-9237 Rev.3 P. 2 / 2

M-system CLSP User manual

Brand: M-system

Model: CLSP

Type: User manual

M-system CLSP

Download PDF

report

M-system CLSP User manual

M-system CLSP User manual

Related papers

Other documents