Product code
052 xx 7921
Assembly Instruction
610 00 7921
Issue: B
Help and advice
Tools Required Help and Advice
Dear Customer,
In the unlikely event of you finding any parts either missing or faulty, it will not be
necessary to go to the trouble of returning the complete item.
Simply Write to us at: Customer Service Department, Addspace Furniture Limited,
Braithwell Way, Hellaby Industrial Estate, Hellaby, Rotherham, South Yorkshire, S66 8 QY.
Please include the following information: Unit Description, Product Code, Product Colour,
Place of Purchase, Catalogue Ref. No., Item Code.
THE SCREWPACK CONTAINS ITEMS WHICH MAY PROVE DANGEROUS TO CHILDREN
ESPECIALLY THOSE UNDER
36 MONTHS. WE THEREFORE RECOMMEND CAUTION IS
OBSERVED DURING THE ASSEMBLY OF YOUR UNIT. IF THE UNIT CONTAINS SCREW
COVERCAPS, WE SUGGEST THAT THESE ARE GLUED INTO POSITION.
You can also e-mail your requests to us at: customer[email protected].uk
Alternatively contact us on 01709 534123 and leave your name, address, daytime telephone
number and the nature of your call on the answerphone. All calls will be actioned asap.
NEST OF TABLES
Step by Step Assembly Instructions
Product Dimensions
HHHHxWWWWxDDD
420x420x420mm
Tape Measure
Cross Head Screwdriver
Do not throw away any of the packaging until you have checked
that you have all the component parts and fittings.
IMPORTANT! PLEASE READ.
Before you start take a few moments to
read through this leaflet and then follow
the step by step instructions.
CUSTOMER HELPLINE:
01709 534123
ASSEMBLY TIME: 45min Approx.
COMPONENT PARTS LIST
DESCRIPTION SIZE QTY CODE
TOP(LARGE) 420x420x15 1
5996
PAGE 2
760001103
CODE QTY
760003004
CODE QTY
16 16
aa bb
FITTINGS
5996
6003
6005
TOP ( SMALL) 360x360x15 1
5997
LH END ( LARGE ) 404x404x15 1
5998
RH END ( LARGE ) 404x404x15 1
6003
5998
5997
6004
5999
6013
LH END ( SMALL ) 344x344x15 1
5999
RH END ( SMALL ) 344x344x15 1
6004
RAIL ( LARGE ) 376x190x15 1
6005
RAIL ( SMALL ) 316x190x15 1
6013
0
10
20
30
40
50
60
mm
STEP 1 PAGE 3
LOCATE FITTINGS - NOTE: THICK LINES INDICATE FINISHED EDGES.
Fittings you will need in this step:
5996
LOCATE FITTINGS - CONTINUED...
(x4)
(x8)
bb
aa
ENSURE CAM ARROW
POINTS TOWARDS EDGE
WITH HOLE.
SCREW IN DOWEL
UNTIL TIGHTENED.
bb
bb
bb
aa
aa
bb
bb
bb
bb
bb
aa
Fittings you will need in this step:
bb
5997
aa
aa
(x4)
bb
(x4)
aa
(x4)
bb
Fittings you will need in this step:
(x8)
aa
Fittings you will need in this step:
6003
5998
bb
bb
bb
bb
bb
bb
bb
bb
aa
aa
aa
aa
aa
aa
aa
aa
aa
aa
aa
aa
6004
5999
LOCATE FITTINGS - CONTINUED...
LOCATE FITTINGS - CONTINUED...
6013
6005
STEP 3 PAGE 4
STEP 5
LIFT UNITS UP
LOCATE LH/RH ENDS TO RAILS
CONGRATULATIONS YOUR UNIT IS COMPLETE
PLEASE NOTE:TO KEEP YOUR UNIT IN PERFECT CONDITION CLEAN ONLY WITH A SOFT DAMP CLOTH.DO NOT USE
ANY ABRASIVE CHEMICAL CLEANERS. DO NOT SUBJECT YOUR UNIT TO HEAT OR MOISTURE. I E BY
PLACING HOT OR DAMP CUPS ETC ON ANY OF THE SURFACES.
STEP 4
ATTACH TOP LH/RH END PANELS
INSERT DOWELS IN
PANELS 5998,5999,
6003 AND 6004 INTO
CAMS IN RAILS 6005
AND 6013.
THEN LOCK.
TURN CAM 180 DEGREES
TO LOCK.
6005
5996
5998
6003
6013
5999
6004
5997
5998
6003
5999
6004
INSERT DOWELS IN
PANEL 5996 AND
5997, INTO CAMS IN
PANELS 5998,5999
6003 AND 6004.
THEN LOCK.
TURN CAM 180 DEGREES
TO LOCK.
WE RECOMMEND THAT THE UNIT IS LIFTED AND NOT DRAGGED.
/
