Polar PDT 819 Program Chart

Brand: Polar

Model: PDT 819

Type: Program Chart

GB PDT 819

5019 801 10014

Programme Care Labels Type of wash / Notes

Max.

Load

Detergents and Additives Special options Max.

Spin

Speed

rpm

Temperature

Selector

°C

Programme

Selector

Softener Main

Wash

Pre-

wash

Intensive

Rinse

Intensywne

p³ukanie

Cotton with prewash

Heavily soiled, long wearing and temperature stable textiles in cotton and linen (bed linen, table linen, underwear,

shirts etc.).

4,5

Yes Yes

800 Max. 95°

Synthetics with

prewash

Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, Nylon) or blends

with cotton.

2,5

Yes Yes

800 Max. 60°

Delicate with prewash Heavily soiled curtains and delicate clothing, dresses, skirts, shirts and blouses.

1,5

Yes Yes – 800 Max. 40°

Cotton Slightly to normally soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.

5,0

Yes –

800 Max. 95°

Cotton short Slightly soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen.

3,0

Yes –

800 Max. 60°

Synthetics

Slightly to normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon,

Nylon) or blends with cotton.

2,5

Yes –

800 Max. 60°

Synthetics short Slightly soiled overalls and sportswear made of cotton, polyester, polyamide and blends with cotton.

2,5

Yes –

800 Max. 60°

Delicate Curtains and delicate clothing, dresses, skirts, shirts and blouses.

1,5

Yes – – 800 Max. 40°

Wool Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable.

1,0

Yes – – 800 Max. 40°

Handwash Textiles made of silk, linen, wool and viscose marked as “handwashable”.

1,0

Yes – – –

Max. 30°

Rinse and Spin

–

With this programme you can add starch and/or fabric softener.

The programme ands with an intensive spin cycle.

5,0

– –

800 –

Spin

–

In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.

5,0 – – – – 800 –

Gentle Spin

–

In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.

1,5 – – – – 800 –

Drain

–

Drain only - no spinning.

– – – – – – –

i : option / Yes : dosing required

For improved garment care spin speed is zero in this

programme.

A. “On/Off” Button (W³./Wy³.)

During the selected washing programme the

programme selector knob moves by steps

clockwise through the phases prewash, main

wash, rinse and spin. Each step takes from

some seconds to several minutes.

5019 801 10014

Programme

Temperature

Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 95 4,5 49* 1,70 2:05

Cotton 60 5,0 46 0,95 2:20

Cotton 40 4,5 44 0,60 2:05

Synthetics 60 2,0 55 0,80 1:30

Synthetics 40 2,0 55 0,60 1:20

Delicates 30 1,5 60 0,50 0:45

Wool 30 1,0 60 0,30 0:40

Handwash 30 1,0 60 0,30 0:50

Add the detergents as described in the programme

table or in the chapter “Detergents and Additives” in

the booklet.

1. Open the tap.

2. Turn the programme selector to the desired

programme.

3. Turn the temperature selector to the desired

temperature.

4. Turn the spin selector to the desired speed.

5. Special options can be selected.

6. Check that the door is well closed and turn

on the washing machine by pressing the

“On/Off” (W³./Wy³.) button. The indicator lights

up, indicating that the washing machine is on.

CONSUMPTION DATA

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values

in the table in relation to the water supply pressure and temperature, the load and the type of wash.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains

the water out.

ADD DETERGENTS, CLOSE THE DOOR AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

PROGRAMME CHANGE

To reselect a programme when a cycle has already

begun:

1. Switch off the appliance by pressing the

“On/Off” (W³./Wy³.) button.

2. Select the new programme.

3. Start the programme by pressing the “On/Off”

(W³./Wy³.) button.

END OF WASH CYCLE

1. At the end of the programme the programme

selector moves to the stop position.

2. To unload the machine wait for the door to

unlock (about 1 minute).

3. Switch off the appliance, open the door and

take out the laundry.

4. Close the tap and leave the door ajar to allow

the drum to dry out.

NOTES AND INDICATIONS FOR USE

• WATER LEVEL

It may not be visible as the cycle is optimised

for a minimum water consumption without

compromising washing results.

• SPIN SPEED CONTROL

Spin speed may be reduced automatically or

may even be excluded in the case of small

loads with highly absorbent garments (e.g.

bathrobes, bathmat).

This control avoids cloth and machine damage

and excessive vibrations and consequent noise

produced by the machine due to load

unbalance: by selecting high spin speeds the

noise level increases.

• MOTOR NOISE

The running noises of the new, electronically-

controlled motor are not the same as the ones

you are used to from your old appliance. Don't

be surprised - modern technology has a modern

sound.

• CLEANING THE FILTER

To ensure an impeccable function of the pump,

check the filter regularly and clean it if

necessary.

“Intensive Rinse” button (Intensywne p³ukanie)

• The amount of water is increased to ensure a

more intensive rinse.

• This option is particulary suitable for areas with

very soft water, washing baby linen and people

with detergents allergies.

Polar PDT 819 Program Chart

Polar PDT 819 Program Chart

Polar PDT 819 Program Chart

Related papers

Other documents