Page is loading ...
AT-BRKT15 Wall-Mount Bracket Installation Manual
This manual will assist you in the installation of your AT-BRKT15. When
opening this Allied Telesyn product, make sure the package you have
received is complete and free of visible damage from shipping. This pack-
age should include:
• 1 bracket (A)
• 4 #8 x 7/8" self-tapping panhead screws (D)
• 4 “Bantam Plug” #8-10 plastic screw anchors
• Cable tie wraps (C)
NOTE
The AT-BRKT15 is only designed for use in ATI products.
The AT-BRKT15 is for mounting the ATI repeaters, such as the
AT-MR12x, AT-MR410T and AT-MR810T series, that are housed in the
“slim-line” micro-case.
Installation of the repeater in the mounting bracket requires the follow-
ing tools:
• Mounting screws for your application (shown in Figure 1 as D)
• Hammer
• Drill and 3/16" bit (or equivalent)
• Pencil
• Awl or other punch
NOTE
The AT-BRKT15 must be mounted in a vertical orientation with the
power supply (as indicated by the power receptacle)
up
to gain
maximum convection cooling.
Allied Telesyn International
19015 North Creek Parkway, Suite 200
Bothell, WA 98011
U.S. & International Tel: 800/424-4284
Technical Support Tel: 800/428-4835
4
PN 613-10353 Rev. A
This document produced using
Recycled Materials
Installing your Allied Telesyn AT-BRKT15
Refer to Figure 1.
1. Using the bracket as a template, mark the screw holes.
2. Use an awl or other punch to punch pilot holes.
3. Drill the holes.
4. If mounting on wallboard, insert the Bantam plugs into the holes.
Figure 1: Vertical Installation Example
Gently encourage the plugs with a hammer if necessary.
5. Remove the repeater’s bottom corner screws (B) and rubber feet.
6. Mount the repeater in the bracket using the corner screws, but
without the rubber feet.
7. Mount the bracket to the wall using the #8 x 7/8" pan head Phillips
screws (D).
8. Set aside the rubber feet. They are no longer required.
For specific dimensions, please see Figure 2.
Figure 2: Dimensions
These dimensions are subject to change without further notice from ATI.
C
D
B
A
B
D
4.63
0.20
0.37
0.14
3.67
4.63
1.70
6.14
10.40
8.15
(15.60)
(11.76)
(0.94)
(0.36)
(0.51)
(9.32)
(11.76)
(4.32)
(26.42)
(20.70)
2 3
Installing your Allied Telesyn AT-BRKT15
Refer to Figure 1.
1. Using the bracket as a template, mark the screw holes.
2. Use an awl or other punch to punch pilot holes.
3. Drill the holes.
4. If mounting on wallboard, insert the Bantam plugs into the holes.
Figure 1: Vertical Installation Example
Gently encourage the plugs with a hammer if necessary.
5. Remove the repeater’s bottom corner screws (B) and rubber feet.
6. Mount the repeater in the bracket using the corner screws, but
without the rubber feet.
7. Mount the bracket to the wall using the #8 x 7/8" pan head Phillips
screws (D).
8. Set aside the rubber feet. They are no longer required.
For specific dimensions, please see Figure 2.
Figure 2: Dimensions
These dimensions are subject to change without further notice from ATI.
C
D
B
A
B
D
4.63
0.20
0.37
0.14
3.67
4.63
1.70
6.14
10.40
8.15
(15.60)
(11.76)
(0.94)
(0.36)
(0.51)
(9.32)
(11.76)
(4.32)
(26.42)
(20.70)
2 3
AT-BRKT15 Wall-Mount Bracket Installation Manual
This manual will assist you in the installation of your AT-BRKT15. When
opening this Allied Telesyn product, make sure the package you have
received is complete and free of visible damage from shipping. This pack-
age should include:
• 1 bracket (A)
• 4 #8 x 7/8" self-tapping panhead screws (D)
• 4 “Bantam Plug” #8-10 plastic screw anchors
• Cable tie wraps (C)
NOTE
The AT-BRKT15 is only designed for use in ATI products.
The AT-BRKT15 is for mounting the ATI repeaters, such as the
AT-MR12x, AT-MR410T and AT-MR810T series, that are housed in the
“slim-line” micro-case.
Installation of the repeater in the mounting bracket requires the follow-
ing tools:
• Mounting screws for your application (shown in Figure 1 as D)
• Hammer
• Drill and 3/16" bit (or equivalent)
• Pencil
• Awl or other punch
NOTE
The AT-BRKT15 must be mounted in a vertical orientation with the
power supply (as indicated by the power receptacle)
up
to gain
maximum convection cooling.
Allied Telesyn International
19015 North Creek Parkway, Suite 200
Bothell, WA 98011
U.S. & International Tel: 800/424-4284
Technical Support Tel: 800/428-4835
4
PN 613-10353 Rev. A
This document produced using
Recycled Materials
/
