5019 301 05345
Whirlpool is a registered trademark of Whirlpool USA
Programme
Care
Labels
Type of wash/Notes
Max
Load
Detergents and additives Special options Max
Spin
Speed
rpm
Tempera-
ture
°C
Bleach Softener Main
Wash
Prewash Start
Delay
Easy
Ironing
Prewash Intensive
Rinse
Rinse
Hold
Spin Speed
Reduction
kg
Départ
retardé
Anti-
froissage
Pré-
lavage
Rinçage
plus
Arrêt cuve
pleine
Essorage
Cotton
Coton
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc.
made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be selected as well.
5.5
❉❉
Yes
❉❉❉❉ ❉ ❉ ❉
1400
20 to 95
Synthetics
Synthétiques
Normally to heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen,
Trevira), polyamide (Perlon, Nylon) or blends with cotton.
2.5
—
❉
Yes
❉❉❉❉ ❉ ❉❉
1)
900
1)
20 to 60
Daily
Slightly to normally soiled textiles made of cotton and/or synthetics.
3.0
—
❉
Yes —
❉❉
—
❉❉❉
1400
30 to 60
Rapid Plus
Chrono
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with
cotton.
3.0
—
❉
Yes —
❉❉
—
❉❉❉
1400
20 to 60
Delicates
Délicat
Curtains and delicate clothing, dresses skirts, shirts and blouses.
1.5
—
❉
Yes
❉❉
—
❉
—
❉❉
1)
900
1)
20 to 40
Wool
Laine
Only woollens with a felt-free finish, labelled with the woolmark and identified as
machine washable.
If you select “Rinse Hold” do not leave items to soak for too long.
1.0
—
❉
Yes —
❉
———
❉❉
1)
900
1)
20 to 40
Silk
Soie
Textiles made of silk, linen, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. No spinning.
1.0
—
❉
Yes —
❉
———
❉
—
0
2)
20 to 30
Rinse + spin
Rinçage & Essorage
—
Same as the last rinse and the final spin in the “Coloured Cotton” programme.
5.5
—
❉
——
❉❉
—
❉❉❉
1400
—
Spin
Essorage
—
In this programme spinning is intensive. Same as the spin cycle in the “Coloured
Cotton” programme.
5.5
—
———
❉
——— —
❉
1400
—
Gentle spin
Essorage court
—
In this programme spinning is gentle. Same as the spin cycle in the “Wool”
programme.
1.5
—
———
❉
——— —
❉
1)
900
1)
—
Drain
Vidange
—
Drain only - no spinning. Alternative method of terminating programme after “Rinse
Hold”.
——
———— — — — —
—
——
A. Temperature Selection Buttons
B. Programme Sequence Indicator
C. “Start/Pause” Button
D. “Door Open” Indication
E. “Start Delay” Button
F. “Spin Speed Reduction” Button
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the
indication lights switch off automatically.
Unsuitable combinations of options are
deselected automatically.
❉
: optional / Yes : dosing required
1)
For improved garment care spin speed is restricted to
900 rpm in this programme.
2)
For improved garment care spin speed is null in this
programme.
A
B
F
DC
E
AWM 8141
GB
3gb05345.fm Page 1 Tuesday, April 30, 2002 2:00 PM
Black process 45.0° 100.0 LPI
5019 301 05345
Whirlpool is a registered trademark of Whirlpool USA
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized
conditions in compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in
the table in relation to the water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the
household conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
Add the detergents as described in the programme
table or in the chapter “Detergents and Additives” in
the booklet.
1. Turn the
programme selector knob
to the
desired programme.
2. The remaining time display shows the duration of
the chosen programme (in hours and minutes)
and the pilot lamp of the
“Start/Pause”
button
is flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
The recommended temperature (see the indicator)
can be altered by pressing “
+
” or “
-
” button.
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the
indication lights switch off automatically.
Unsuitable combinations of options are
deselected automatically.
“Easy Ironing” button
• Can be used together with Cotton, Synthetics and
Daily programmes to make ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive Rinse” button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for the
programme “Synthetics”, “Daily” and “Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
CONSUMPTION DATA
Programme
Temperature Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)*
Cotton 90 5.5 54** 1.90 2:00
Cotton 60 5.5 49 1.04 2:20
Cotton 40 5.0 44 0.60 2:05
Synthetics 60 2.5 55 0.80 1:30
Synthetics 40 2.5 55 0.60 1:20
Daily 40 3.0 44 0.45 1:00
Rapid Plus 30 3.0 37 0.40 0:30
Delicates 40 1.5 60 0.60 0:45
Wool 30 1.0 60 0.30 0:40
Silk 30 1.0 45 0.30 0:40
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE
PROGRAMME
SELECT ANY DESIRED OPTION
Note:
The programme stops to “Rinse Hold” at the
time the “Rinse Hold” light in the programme flow
indication is on.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the
“Start/Pause”
button
again when flashing.
“Spin Speed Reduction” button
• Every programme has an automatic predefined
maximum spin speed.
• Press the button to set another spin speed.
• If the spin speed “
0
” is selected, the final
spinning is cancelled but intermediate spin
peaks remain during rinse. The water is drained
out only.
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night
when electricity is cheaper.
• Select programme, temperature and options.
• Press the “Start Delay” button to select the
delay time by 1 to 23 hours;
• Press the
“Start/Pause”
button.
• The time delay indication disappears when the
programme starts and it is replaced by the
remaining time.
• The number of hours preselected can later be
reduced pressing again the “Start Delay”
button.
To cancel the “Start Delay”.
• Turn the programme selector to the “”
position.
• Reselect the desired programme and options
and press the
“Start/Pause”
button.
Open the tap and press the
“Start/Pause”
button.
The pilot lamp of the
“Start/Pause”
button lights
up.
The indicator lamps show the sequence reached in
the programme. After starting the programme, the
sequence indication runs from left to right through
Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding lamp goes out.
The door can be opened when the “Door Open”
indication is on.
• The remaining time is on “0:00” and all the lights
of the programme sequence indication are off.
1. Turn the programme selector to the
“”
position.
2. Turn the water supply tap off.
3. Open the door and unload the machine.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. Press the
“Start/Pause”
button again. The
new programme continues at the same position
where the previous programme was
interrupted. Do not add detergent for this
programme.
1. Press the
“Start/Pause”
button to pause the
programme. The light flashes.
2. Set the programme selector to “Drain”. The
spin indicators show
“0”
and the remaining
time shows “0:02”.
3. Press the
“Start/Pause”
button to start the
drain programme.
START DELAY
PROGRAMME START
DOOR LOCK
PROGRAMME END
CHANGE THE PROGRAMME, TEMPERATURE,
OPTIONS AFTER PROGRAMME START
CANCEL A PROGRAMME BEFORE THE END
3gb05345.fm Page 2 Tuesday, April 30, 2002 2:00 PM
Black process 45.0° 100.0 LPI
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool AWM 6103 Owner's manual
-
-
-
-
-
-
-
-
-