This supplement provides corrections to and additional information for the
ThinkPad 600E User's
Reference
(part number 27L8078). Read this supplement with the
User's Reference
.
Setting the Region Code
If you want to view a DVD movie on your computer, you need to set the DVD region code. You can set
the region code when you start DVD Express for the first time. For instructions for setting the region
code, read this flyer instead of the
Online User's Guide
.
DVD Region Codes:
Regional coding is part of the protection scheme for DVD content. The world is divided into six
regions, so that specific content can be viewed only in the region where it is appropriate. For
example, Region 1 (U.S. and Canada) content can be viewed only in Region 1. The DVD Movie
Player Program application is also region–specific. You must select a region to play DVD
content. After you have selected a region, you can play content only from that region.
An
incorrect region code setting causes your computer to hang; you can recover your
computer only with the Recovery CD.
Part Number: 27L8312
ThinkPad 600E
User's Reference Supplement
Note: When you view a DVD movie on your computer, only the 800x600 resolution with the 256-color LCD setting
is available.
Copyright IBM Corp. 1998
1
Attention
Make sure the first DVD content you play is from the appropriate region. You can verify the
region code of the content by looking at the region code symbol on the back of the content
packaging. If the first DVD you play is from a region other than the region you selected, your
system will no longer play DVD content. Recover your system using the Recovery CD.
To set the region code, do as follows:
1
Click on Start, move the cursor to Programs and Mediamatics DVD Express, and then click on
Mediamatics DVD Player.
The “Select DVD Region” window appears.
2
Select the region code and click on OK.
Installing the Hot/Warm Swap Driver
The hot/warm swap driver is preinstalled in your computer. If you need to reinstall the driver, read the
appropriate section.
To install the hot/warm swap driver
for Windows 98
, do the following:
1
Start Windows 98.
2
Insert the Utility Driver Diskette for Windows 95 into the diskette drive.
3
Click on Start and move the cursor to Settings and Control Panel.
4
Click on Control Panel.
Region Code Country
1 U.S. and Canada
2 Europe, Middle East, South Africa, Japan
3 Southeast Asia, Taiwan, Korea
4 Latin America, Australia, New Zealand
5 Former Soviet Union, the rest of Africa, India
6 People's Republic of China
2
5
Double-click on Add New Hardware.
6
Click on Next.
7
Click on Next again.
8
Select No, and click on Next.
9
Select No again, and click on Next.
10
Click on Other devices, and click on Next.
11
Click on Have Disk....
12
Type A:\
13
Click on OK.
14
Select ThinkPad Hot/Warm Swap Driver, and click on Next.
15
Click on Finish.
16
Restart the computer.
To install the hot/warm swap driver
for Windows 95
, do the following:
1
Start Windows 95.
2
Insert the Utility Driver Diskette for Windows 95 into the diskette drive.
3
Click on Start and move the cursor to Settings; then click on Control Panel.
4
Double-click on Add New Hardware.
5
Click on Next.
6
Select No, and click on Next.
7
Click on Other devices, and click on Next.
8
Click on Have Disk....
9
Type A:\
10
Click on OK.
3
11
Select ThinkPad Hot/Warm Swap Driver, and click on Next.
12
Click on Finish.
13
Restart the computer.
Corrections to the User's Reference
This section corrects information in the
User's Reference
. Use this information instead of the
corresponding information in the
User's Reference
.
The term
UltraslimBay tray
in the
User's Reference
should be
UltraBay tray
.
If you want to use two diskette drives at the same time, you need to install one drive in the
UltraslimBay. The secondary drive can be one of the following:
– Attached to the computer's external diskette drive connector
– Attached through the port replicator
– In the bay of the docking station
If you dock your computer to a docking station:
– If you use a SelectaDock I or SelectaDock II docking station, connect the power cord to a
docking station and connect the AC Adapter to a SelectaBase 600 port replicator.
– If you use a SelectaDock III docking station, connect the power cord to the docking station.
Protection Notice Requirement
This device is protected by U.S. patent numbers 4631603, 4577216, 4819098, 4907093, and other
intellectual property rights. The use of Macrovision's copy protection technology in the device must
be authorized by Macrovision and is intended for home and other limited pay-per-view use only,
unless otherwise authorized in writing by Macrovision. Reverse engineering or disassembly is
prohibited.
4
/