VarTech Systems VT084XB4 User manual

1

VT084 All Weather User’s Guide 150-181

Solutions for Demanding Applications

All Weather Series LCD Monitors

VT084XA4 · VT084XB4

User’s Guide

2

VT084 All Weather User’s Guide 150-181

Read these instructions completely before attempting to operate your new LCD Color Display.

Table Of Contents

Page

Section 1 Introduction

Section 4 Touchscreen

1.0 Overview 3 4.1 Touch Screen Introduction 11

1.1 VT084 General Features 3 4.2 Touch Screen Installation 11

1.2 Product Safety Precautions 3

Section 2 Display Setup Section 5 Troubleshooting

2.1 Inspection 4 5.1 General 12

2.2 Unpacking 4

2.3 Included Parts 4 Section 6 Maintenance

2.4 Installation Guidelines 4-5 6.1 Cleaning 13

2.5 Video Input Connections 6

Specifications 14-15

Section 3 Getting Started

3.1 Adjusting the display 7 Mechanical Drawings 16-17

3.2 OSD Adjustments 8-10

3

VT084 All Weather User’s Guide 150-181

INTRODUCTION

SECTION 1

1.1 Overview

VarTech All-Weather series includes waterproof, totally sealed, IP67 NEMA 6 LCD displays. These high resolution,

sunlight readable LCD displays provide exceptional clarity, viewing angles, extensive operational temperatures

(-40°C to +70°C), IP67 (NEMA 6) protection, and offer durable, 5-Wire, resistive touch screens.

1.2 VT084 General Features

o IP67 Fully Enclosed LCD

o Rugged Machined 6061 T6 Aluminum Enclosure

o Solid State LED Backlighting

o Optical Bonding (VBOND) front overlay (AR)

o Optional Resistive Touch Screens, standard and Armor

o VESA, Flush, RAM, and Panel Mounting Options

o Full Range Manual Dimming

o Push Button OSD (On-Screen Display)

1.3 Product Safety Precautions

• Ensure that sufficient space is available around the display to provide the circulation necessary for cooling.

• Ensure that the ambient air temperature will not exceed the specified maximum temperature.

• Do not attempt to service this display yourself. The rear chassis has a seal so that non qualified personnel

will not expose themselves to dangerous voltages or other risks.

• To protect from electrical shock, unplug the display power supply from the wall before moving.

• Do not place any heavy objects on the power cords. Damage may cause electrical shock.

• Unplug the power supply from the wall or unit if one of the following conditions exists:

Power cord or plug is damaged or frayed.

The display does not operate normally when the operating instructions are followed.

The display has been dropped or the enclosure has been damaged.

The display exhibits a distinct change in performance, indicating a need for service.

4

VT084 All Weather User’s Guide 150-181

DISPLAY SETUP

SECTION 2

2.1 Inspection of your VT084 All Weather Display

The Vartech VT084 All Weather display is supplied with different accessories depending on the model

configuration purchased. Verify that the display and accessories are what were ordered. Contact your Vartech

salesperson should there be any discrepancies.

2.2 Unpacking and setting up your VT084 All Weather Display

Before unpacking the product, inspect the shipping carton for damage. If damage is visible, immediately contact

VarTech and request assistance. Otherwise, proceed with unpacking. Keep the original packing material in case

you need to return the product for repair or transport it to another location. Use both the inner and outer packing

cartons to provide adequate protection for a unit returned for service.

Your display monitor package will consist of all or some of the components listed below. Open shipping

container and place all the components on a flat clean surface.

2.3 What is included with your VT084 All Weather Display

Installation instructions and cutout template

Panel Mount Screws

Four VESA or RAM mounting screws

Power cable and AC adapter if ordered

Video cable for input ordered (VGA, DVI, BNC)

Touch Interface Cable, Serial or USB (Optional when touch is installed)

CDROM with Touch Screen Drivers (Optional when touch is installed)

2.4 Installation Guidelines

Panel Mounting Guidelines

Observe these guidelines when installing the monitor in a panel.

Cut supporting panels to specifications before installation. Take precautions so metal cuttings do not enter

components already installed in the panel.

Supporting panels should be at least .125” thick in order to provide proper sealing against water and dust and

to provide proper support.

Install the monitor into the panel be careful not to cut hand on metal. Use .125” thick supplied gasket to ensure a

watertight seal. Do not use an adhesive.

Tighten the provided bolts. Do not over tighten as that can damage the helicoil inserts.

5

VT084 All Weather User’s Guide 150-181

VESA Mounting Guidelines

The VESA-mount option is used to install the monitor on an articulated arm using an optional bracket. For

a list of available mounts, please contact your Vartech salesperson.

Mounting Guidelines

Observe these guidelines when installing the monitor on an arm.

The mounting surface and the mounting arm must be strong enough to support both the monitor and the

mounting hardware.

The interface between the arm and the monitor must meet VESA FPMPMI 100 mm standards.

The mounting location must provide adequate clearance for positioning and moving the adjustable unit and

routing cables.

Mount the Monitor on a VESA Interface

Follow these steps to mount the monitor on a VESA interface.

1. Mount the arm to the VESA interface with screws, bolts, or clamps so the monitor cannot tip.

2. Align the monitor over the arm and insert four supplied screws through the arm bracket and into the monitor.

RAM Mounting Guidelines

RAM is the only universal ball-and-socket system that holds excessive amounts of weight in high vibration

applications for military, commercial and private use.

Mounting Guidelines

Observe these guidelines when installing the monitor on the provided RAM.

The mounting surface must be strong enough to support both the monitor and the RAM.

The mounting location must provide adequate clearance for positioning and moving the adjustable unit and

routing cables.

Follow these steps to mount the monitor on a RAM.

1. Mount the Base plate to the mounting surface where the monitor is intended to be permanently mounted

2. Mount the Shaft to the RAM interface by prying open the socket and slipping over the mounting ball.

3. Align the RAM monitor plate, attach using the supplied screws into the 3 RAM mounting holes (triangular

pattern)

4. Loosen the socket and slip the ball into the socket. Secure in place by tightening the socket.

Mechanical Drawings

Model

Description

Page(s)

VT084XA4/XB4

VESA/RAM Mount Drawing

16

VT084XA4/XB4

Flush Mount

17

6

VT084 All Weather User’s Guide 150-181

2.5 Input Video Connections

Typical Input Assembly

Connect to an Analog Video Source

All of the monitors support analog video. Your monitor is shipped with a high-quality analog video cable.

Use this video cable to connect a computer to the monitor.

Follow these steps to connect the monitor to an analog video source.

1. Connect one end of the 3 m (10 ft), analog video cable to the circular, 10pin VGA video input connector

on the monitor. Careful to align the red lines

2. Connect the other cable end to the VGA port of the computer.

You can use a couple to join to another cable with a maximum combined length of 15 m (50 ft) at lower monitor

resolutions, provided it is a high-quality video cable. Video amplifiers are available for longer distances.

7

VT084 All Weather User’s Guide 150-181

GETTING STARTED

SECTION 3

3.1 Adjusting the display

Set the monitor type

The VT084XA/XB monitors are not plug n play compatible and require initial setup to begin operation

1. Ensure video and power cables are connected and secure and connected to the source

2. Power on the monitor

3. Toggle through the input select button until your video source is labeled and the video is showing

4. Adjust geometry of screen if necessary by using the advanced On-screen display. Activate the OSD

By pushing the MENU button, move to the necessary sub menus by using the +/- keys and entering select

5. Make adjustments and save by exiting the menu

6. Once the initial setup is complete you will not be required to redo

On/OFF

Menu

-

+

Select

Input Select

Dimming POT

8

VT084 All Weather User’s Guide 150-181

3.2 OSD Adjustments

Selection page

Select input source

Select input source to Analog RGB

Select input source to DVI

Select input source to S-Video 1

Select input source to Composite 1

Select input source to S-Video 2 (No function now)

Select input source to Composite 2 (No function now)

Auto Source Seek

ON – Auto source select always enable

OFF – Disable auto source select function

Video system selection* 

Select Auto video system detection

Select PAL video system

Select PAL M video system

Select NTSC video system

Select NTSC 4.43 video system

Select SECAM video system

Wide screen mode

information display#

Select the input mode (1280 / 1360 / 1366 / 1368) to recognize and display the correct input

signal information display on the OSD menu.

1280 : 1280x768 1366: 1366x768

1360 : 1360x768 1368: 1368x768

9

VT084 All Weather User’s Guide 150-181

Exit

Exit the OSD menu and save the settings

Brightness and Contrast

Brightness

Increase/decrease brightness level.

Press – or + (- + ) Total : 256 steps

Contrast

Increase/decrease panel contrast level.

Press – or + (- + ) Total : 192 steps

Saturation*

Increase/decrease hue level.

Press – or + (- + ) Total : 256 steps

Hue*

Increase/decrease saturation level

Press – or + (- + ) Total : 128 steps

Exit

Exit the OSD menu and save the settings

Color

Auto RGB Calibration#

Yes

No

Color Temperature  (Adjust the warmness of the image displayed. The higher temperature the

coolest image looks like. The lower temperature the warmest image looks like.)

Adjust red color level

Press – or + (- +) Total :128 steps

Adjust green color level

Press – or + (- +) Total : 128 steps

Adjust blue color level

Press – or + (- +) Total : 128 steps

Press SEL UP/DN button to select item

Set the color temperature to 4200K

Set the color temperature to 5000K

Set the color temperature to 6500K

Set the color temperature to 7500K

Set the color temperature to 9300K

Gamma adjustment

Adjust Gamma settings (0.4 / 0.6 / 1.0 / 1.6 / 2.2)

Select Gamma to 0.4

Select Gamma to 0.6

Select Gamma to 1.0

Select Gamma to 1.6

Select Gamma to 2.2

Exit

Exit the OSD menu and save the settings

Position#

Auto setup

Auto adjust the positions, phase, frequency

Yes No

Frequency

Adjust the image horizontal size

Phase

Fine tune the data sampling position (adjust image quality)

Image Horizontal Position

Use +/- to move the image horizontally

Press – or + (- + )

Image Vertical

Use +/- to move the image vertically

Press – or + (- + )

Exit

Exit the OSD menu

10

VT084 All Weather User’s Guide 150-181

Utilities

OSD setting 

OSD Timeout : 0 / 10 / 20 / 30 / 40 / 50 / 60 seconds (Always on when set to 0)

Press – or + (- + )

OSD menu horizontal position

Press – or + (- + )

OSD menu vertical position

Press – or + (- + )

Load Factory Default

Initialize the setting stored in non-volatile memory

Sharpness

Adjust sharpness level

Press – or + (- + ) Total : 49 steps

Exit

Exit the OSD menu

* - Function in Video mode only

# - Function in ARGB mode only

Items marked  have sub menus.

Exit the OSD menu to save the setting chosen

Adjust the Brightness

Use the dimming potentiometer located on the front bottom right corner of the display to adjust the brightness level of the

LED backlights.

11

VT084 All Weather User’s Guide 150-181

TOUCHSCREEN

SECTION 4

4.1 Introduction

Touch screens are a common means to interface operator inputs to a system. The universal standard of Windows GUI

(Graphical User Interface) has significantly increased the use of touch screens.

The Vartech All Weather series offers two styles of 5 wire resistive technologies. The styles are standard resistive

and the more durable Armor resistive touch.

4.2 Installation

All Vartech Systems displays configured with a touch screen are supplied with a CDROM which includes user manuals,

application software, and drivers for various operating systems. Insert the supplied CDROM into a CDROM drive and

follow the installation instructions that will appear on the screen.

Technical support is available by contacting Vartech Systems customer support at 800-223-8050.

12

VT084 All Weather User’s Guide 150-181

TROUBLESHOOTING

SECTION 5

5.1

General

A general guide to troubleshooting a flat panel display system it is worth considering the system as separate elements,

such as: Controller (jumpers, PC settings) Panel (controller, cabling, connection, panel, PC settings) Backlight (inverter,

cabling,) Cabling Computer system (display settings, operating system) Through step by step cross checking with

instruction manuals and a process of elimination to isolate the problem it is usually possible to clearly identify the

problem area.

No image:

If the panel backlight is not working it may still be possible to just see some image on the display. A lack of

image is most likely to be caused by incorrect connection, lack of power, failure to provide a signal or

incorrect graphic card settings.

Image position:

If it is impossible to position the image correctly, i.e. the image adjustment controls will not move the image far enough,

then test using another graphics card. This situation can occur with a custom graphics card that is not close to standard

timings or if something is in the graphics line that may be affecting the signal such as a signal splitter (please note that

normally a signal splitter will not have any adverse effect).

Image appearance:

A faulty panel can have blank lines, failed sections, flickering or flashing display and

individual pixels, incorrect graphics card refresh rate, resolution or interlaced mode will

probably cause the image to be the wrong size, to scroll, flicker badly or possibly even

no image. Incorrect jumper settings on the controller may cause everything from total

failure to incorrect image. CAUTION: Do not set the panel power input incorrectly.

Sparkling on the display: faulty panel signal cable.

Backlight:

Items to check include: Power input, Controls, cables, and Inverter generally in this order. If half the screen is dimmer

than the other half: Check cabling for the inverter. If adjusting brightness control has no effect the chances are that the

VR rating or method of adjusting brightness is not compatible or correctly connected to the inverter. If system does not

power down when there is a loss of signal

Continued failure:

If unit after unit keeps failing consider and investigate whether you are short circuiting the equipment or doing

something else seriously wrong.

Generally after common sense issues have been resolved we recommend step by step substitution of known working

parts to isolate the problem.

13

VT084 All Weather User’s Guide 150-181

MAINTENANCE

SECTION 6

6.1 Cleaning

Occasionally clean the display panel and cabinet with a soft cloth dampened (not soaked) with a mild (non-abrasive)

glass cleaner. Keep turning a fresh side of the cloth toward the screen surface to avoid scratching it with accumulated

grit.

Note: The solvent should be applied only to the cloth, and not directly on the monitor screen.

Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow the screen to stand

dry. Special care should be taken when cleaning a touch screen or polycarbonate shield that is installed over the screen.

Abrasive and certain chemical cleaners can easily damage the surface. Never use alcoholic or ammoniac cleaners to

clean the polycarbonate shield or a touch screen.

Note: For best results cleaning a monitor with the optional antireflective tempered glass display shield, a solution of

denatured alcohol is recommended to thoroughly clean the display.

Replacing a Line Cord

To avoid shock and fire hazards, the monitor’s power cord should be replaced if the insulation becomes broken or if it

develops a loose internal connection.

Other Maintenance

Qualified service personnel should perform all maintenance, except for the power cord replacement described above.

14

VT084 All Weather User’s Guide 150-181

SPECIFICATIONS

ENGINEERING SPECIFICATIONS – VT084XA

Panel Size 8.4” (21cm)

Type Active Matrix Color Thin Film Transistor (TFT)

Native Panel Resolution SVGA

Pixel Format 800 (H) x 600 (V)

Pixel Pitch 0.213 (H) x 0.213 (V) mm

Pixel Arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe

Dot Pitch 0.0071 (H) x 0.213 (V) mm

Active Display Area

6.709” x 5.031”

170.4mm x 127.8mm

Viewing Angle (Left/Right) 80/80o (typ.)

Viewing Angle (Up/Down) 80/60o (typ.)

Color Gamut 40% (typ.)

Brightness 1200 Nits (typ.)

Contrast Ratio 600:1 (typ.)

Dimming Ratio 5000:1 (min.)

Response Time 25ms (typ.)

Back Lights 1 LED Rail rated 70,000 Hrs.

Video Connectors LEMO IP67

Colors Supported 16,777,216 (8-bit input)

Video Input Analog 0.7v p-p, TTL

Sync Separate H & V, Combined, SOG

Input Voltage 9 to 36VDC (12VDC typ.) – Amperage Draw 2.1A @ 12VDC for 25W

Power consumption 25 Watts (32 Watts with heater)

Temperature

Operating: -20 to 70ºC (optional -40 to 70ºC)

Storage: -40 to 75ºC

Humidity Operating/Storage: 0 to 100 %NC

Operating Altitude

Operating: Up to 10,000 ft

Storage: Up to 45,000 ft

15

VT084 All Weather User’s Guide 150-181

SPECIFICATIONS

ENGINEERING SPECIFICATIONS – VT084XB

Panel Size 8.4” (21cm)

Type Active Matrix Color Thin Film Transistor (TFT)

Native Panel Resolution XGA

Pixel Format 1024 (H) x 768 (V)

Pixel Pitch 0.1665 (H) x 0.1665 (V) mm

Pixel Arrangement RGB (Red dot, Green dot, Blue dot) vertical stripe

Dot Pitch 0.0555 (H) x 0.1665 (V) mm

Active Display Area

6.712” x 5.034”

170.496mm x 127.872mm

Viewing Angle (Left/Right) 85/85o (typ.)

Viewing Angle (Up/Down) 85/85o (typ.)

Color Gamut 72% (typ.)

Brightness 1000 Nits (typ.)

Contrast Ratio 400:1 (typ.)

Dimming Ratio 5000:1 (min.)

Response Time 25ms (typ.)

Back Lights 2 LED Rail rated 70,000 Hrs.

Video Connectors LEMO IP67

Colors Supported 16,777,216 (8-bit input)

Video Input Analog 0.7v p-p, TTL

Sync Separate H & V, Combined, SOG

Input Voltage

9 to 36VDC (12VDC typ.) – Amperage Draw 3.0A @ 12VDC for 36W (with

heater)p

Power consumption 38 Watts (45 Watts with heater)

Temperature

Operating: -20 to 70ºC (optional -40 to 70ºC)

Storage: -40 to 75ºC

Humidity Operating/Storage: 0 to 100 %NC

Operating Altitude

Operating: Up to 10,000 ft

Storage: Up to 45,000 ft

16

VT084 All Weather User’s Guide 150-181

17

VT084 All Weather User’s Guide 150-181

18

VT084 All Weather User’s Guide 150-181

Power Cable Diagram

The RED wire with the +V would be connected to the +DC input voltage (like 12VDC or 24VDC)

The BLACK wire with the –V would be connected to the DC input return.

Considering a DC battery, the +V is the positive terminal on the battery while the –V is the negative terminal on the

battery.

The WHITE wire with the SHD would be connected to the chassis of the voltage source. This wire is connected to the

cable SHIELD to help reduce noise from getting into the cable wires and causing any problems within the display. A

customer could elect not to connect the SHIELD wire.

19

VT084 All Weather User’s Guide 150-181

VARTECH SYSTEMS INC.

HEADQUARTERS

6399 Amp Drive, Clemmons, NC 27012

Toll-Free: 800.223.8050

International Phone: 001.225.298.0300

Fax: 225.297.2440

E-mail: sales@vartechsystems.com

www.vartechsystems.com

VarTech Systems VT084XB4 User manual

VarTech Systems VT084XB4 User manual

Related papers

Other documents