1
Owner’s Manual
Desktop
Charging Stations
USB Charging (Model: CSD1006USB)
AC Charging with Surge Protection (Model: CSD1006AC)
Español 14 • Français 27
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2017 Tripp Lite. All rights reserved.
Product Features 2
Package Contents 2
Optional Accessories 3
Important Safety Warnings 3
Setup 4
USB Charging 5
AC Charging 8
Adjusting Storage Shelf 11
Dividers (All Models)
Specifications 11
Product Registration and 12
Warranty Information
Ultimate Lifetime Insurance 13
Policy (CSD1006AC only)
17-01-038-933657.indb 1 1/5/2017 5:15:57 PM
2
Product Features
Package Contents
Both Models
• Charge up to 10 tablets, smartphones or other mobile devices
• Doubles as a USB or AC charger and storage unit, providing space to neatly
organize your devices as they charge
• Removable dividers customize the unit’s storage space according to the number
and size of devices being charged
CSD1006USB Model
• BC1.2 rapid charging with a single port is capable of providing up to 5V 2.4A
• Overcurrent protection prevents devices from pulling more power than the charger
is capable of supporting
• Overcharging protection stops charging when a device battery is full
CSD1006AC Model
• 2880-joule surge suppression rating
• EMI/RFI noise filtering
• Diagnostic LED indicates Protected (green) and Grounded (red)
• Automatic shutoff cuts power to outlets when the protection circuit has been
compromised
• $100,000 Ultimate Lifetime Insurance for connected equipment
(U.S., Canada, and Puerto Rico only)
CSD1006USB
• USB Charger
• External Power Supply with 5-15P
Plug (Input: 100V-240V, 50/60 Hz;
Max Output: 12V, 8A)
• Enclosure unit with locking lid
• USB charger enclosure mount
• Keys
• Combination cable lock
• Owner’s Manual
CSD1006AC
• 10-Outlet AC Surge Protector
• Enclosure unit with locking lid
• Keys
• Combination cable lock
• Owner’s Manual
17-01-038-933657.indb 2 1/5/2017 5:15:57 PM
3
Optional Accessories
Important Safety Warnings
• M100-Series USB to Lightning
®
Cables
• M110-Series USB to Apple
®
30-Pin Cables
• Always read the safety instructions carefully.
• Keep these instructions for future reference.
• Do not install near any heat sources such as radiators, heat registers, stoves, or
other equipment (including amplifiers) that produces heat.
• Unplug the unit when unused for extended periods of time.
• To reduce the risk of fire or electric shock, do not expose this unit to rain or
moisture, including any dripping or splashing.
• Objects filled with liquids, such as vases, should never be placed on or near the
unit.
• The unit presents an electric shock hazard; do not open.
• The outlet used to power the unit should be easily accessible and located near
the equipment.
• The power supply cord is for indoor use only.
•
Maximum ambient temperature around the unit must not exceed 104°F (40°C).
• The power supply cord’s plug and inlet are used as the disconnect device for
the unit and its connected peripherals. The power supply cord should be easily
accessible during operation.
• Refer to the marking label on the unit for input and output ratings. Do not
overload the power supply.
• Use of this equipment in life support applications where failure of this equipment
can reasonably be expected to cause the failure of the life support equipment or
to significantly affect its safety or effectiveness is not recommended.
17-01-038-933657.indb 3 1/5/2017 5:15:57 PM
4
Setup
Both Models
1
After removing the protective packing, locate the separate box at the
rear of the enclosure unit containing the USB charger or AC surge
protector. Remove it from the box.
2
Remove the enclosure lid by pushing out and lifting up.
17-01-038-933657.indb 4 1/5/2017 5:15:58 PM
5
Setup
3
Lift and remove the storage shelf from the enclosure.
4
Attach the charging unit to the enclosure:
CSD1006USB Model
A
Slide the included mounting bracket onto the enclosure’s rear slots.
17-01-038-933657.indb 5 1/5/2017 5:15:58 PM
6
Setup
CSD1006USB Model (continued)
B
Insert the USB charging unit into the mounting bracket with the USB ports
facing upward.
C
Connect USB charging cables appropriate for the number and type of
devices. The slots located at the top and front of the enclosure base allow for
convenient cable routing.
17-01-038-933657.indb 6 1/5/2017 5:15:59 PM
7
Setup
CSD1006USB Model (continued)
D
Once all desired USB cables are connected, place the storage shelf on top of
the enclosure base.
Note: To remove or adjust storage
shelf dividers, refer to pg. 11.
E
Connect the electronic devices to the USB power cables and place items inside
the shelf tray.
F
Use the included power supply to connect the charging unit to a Tripp Lite
surge protector or AC wall outlet.
G
Proceed to step 5.
17-01-038-933657.indb 7 1/5/2017 5:15:59 PM
8
Setup
B
Connect the AC power cables appropriate for the number and type of
devices. The slots located at the top and front of the enclosure base allow for
convenient cable routing.
CSD1006AC Model
A
Insert the AC surge protector into the enclosure’s rear slots. Make sure the AC
outlets are facing outward.
17-01-038-933657.indb 8 1/5/2017 5:16:00 PM
9
Setup
CSD1006AC Model (continued)
C
Once all desired AC power cables are connected, place the storage shelf on top
of the enclosure base.
D
Connect the electronic devices to the AC power cables and place items inside
the shelf tray.
E
Plug the charging unit into an AC wall outlet.
F
Proceed to step 5.
Note: To remove or adjust storage
shelf dividers, refer to pg. 11.
17-01-038-933657.indb 9 1/5/2017 5:16:00 PM
10
Setup
Both Models
5
To prevent device tampering and theft, reattach the enclosure lid to the
top of the enclosure. Use the included key to lock the barrel lock.
6
Secure the enclosure unit to a desk using the included combination
cable lock.
17-01-038-933657.indb 10 1/5/2017 5:16:01 PM
11
Remove the enclosure lid, then remove any personal electronic devices stored on
the shelf tray. Lift the shelf tray. Once the shelf is removed, push in the three tabs
securing the divider to the bottom of the tray
A
, then pull the divider upward to
disengage from the shelf tray
B
. Repeat as necessary for additional shelf dividers.
Adjusting Storage Shelf Dividers (All Models)
A
B
Specifications
CSD1006USB
Ports (x10) USB A Female
External Power Supply
Input: 100-240V, 50/60 Hz; Max Output: 12V 8A
USB Output Capable of providing up to 5V 2.4A to a single port.
Operating Temperature 41° to 95°F (5° to 35°C)
Storage Temperature -4° to 122°F (-20° to 50°C)
Relative Humidity 20% to 80%
Regulatory Approvals CE, FCC, RoHS, REACH, WEEE
CSD1006AC
Outlets (x10) 5-15R
Input Connection Type NEMA 5-15P Plug
Input Cord Length 6 ft. (1.83 m)
AC Surge Suppression Rating 2880 joules
Operating Temperature 41° to 95°F (5° to 35°C)
Storage Temperature -4° to 122°F (-20° to 50°C)
Relative Humidity 20% to 80%
Regulatory Approvals UL 1449 3rd Edition, RoHS
17-01-038-933657.indb 11 1/5/2017 5:16:01 PM
12
Product Registration
1-Year Limited Warranty (CSD1006USB Model)
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically
entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period
of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited
to repairing or replacing (at its sole option) any such defective products. To obtain service under
this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or
an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized
TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief
description of the problem encountered and proof of date and place of purchase. This warranty does
not apply to equipment, which has been damaged by accident, negligence or misapplication or has
been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any
costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software,
loss of data, costs of substitutes, claims by third parties, or otherwise.
Lifetime Limited Warranty (CSD1006AC Model)
Seller warrants this product, if used in accordance with all applicable instructions, to be free from
original defects in material and workmanship for its lifetime. If the product should prove defective
in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion. Service under this Warranty can only be obtained by your delivering or shipping the product
(with all shipping or delivery charges prepaid) to: Tripp Lite, 1111 W. 35th St., Chicago, IL 60609.
Seller will pay return shipping charges.
The warranties of all TRIPP LITE surge protectors are null and void if they have been connected to the
output of any UPS system. The warranties of all TRIPP LITE UPS Systems are null and void if a surge
protector has been connected to its output receptacles.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT,
MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS,
ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY
EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow
limitations on how long an implied warranty lasts, and some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations or exclusions may not apply
to you. This Warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction.)
WARNING: The individual user should take care to determine prior to use whether this device is
suitable, adequate or safe for the use intended. Since individual applications are subject to great
variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these
devices for any specific application.
17-01-038-933657.indb 12 1/5/2017 5:16:01 PM
13
Ultimate Lifetime Insurance Policy
(CSD1006AC Model Only)
This is a limited warranty valid in the U.S., Canada and Puerto Rico only.
Tripp Lite warrants, for the lifetime of the product, (at Tripp Lite’s option) to repair or replace (on a
pro rata basis) directly connected equipment that is damaged due to power transients while properly
connected to Tripp Lite products offering the Ultimate Lifetime Insurance Policy. Power transients
include spikes and surges on the AC power, data or telephone lines that the Tripp Lite products have
been designed to protect against (as recognized by industry standards). The following four paragraphs
are conditions that must be complied with before the warranty becomes valid; failure to comply with
these requirements will void the warranty.
AC Power Line Transients: To claim damages, the Tripp Lite product must be plugged into a properly
wired and grounded outlet. No extension cords or other electrical connections may be used. The
installation must comply with all applicable electrical and safety codes set forth by the National Electrical
Code (NEC). Except as provided above, this warranty does not cover any damage to properly connected
electronic equipment resulting from a cause other than an “AC power transient”. If user meets all of the
above requirements, Tripp Lite will repair or replace (at Tripp Lite’s option) equipment up to the specified
value (See Ultimate Lifetime Insurance Policy Limits). No coverage is allowed for damage entering from
telephone or data lines, unless they are separately protected, as described below.
Telephone and Data Line Transients: Tripp Lite will repair or replace directly connected equipment
that is damaged by transients on telephone and/or data lines only when all such paths are protected
by a Tripp Lite protection product(s) and the AC power (utility) line is simultaneously protected by a
Tripp Lite power protection device (UPS, surge suppressor or line conditioner) with Ultimate Lifetime
Insurance coverage. Additional telephone and/or data line connected devices downstream must have
their own telephone and/or dataline protectors.
Reimbursement dollar limits will be equal to that of the Tripp Lite power protection protector. Coverage
is excluded where a suitable environment for the protection device is not provided, including, but not
limited to, lack of a proper safety ground. Telephone service equipment must also include a properly
installed and operating “primary protection” device at the telephone service entrance (such devices
are normally added during telephone line installation).
All above warranties are null and void if the Tripp Lite product has been improperly installed, tampered
with or altered in any way, or if the connected equipment was not used under normal operating
conditions or in accordance with any labels or instructions. All claims under this warranty must be
submitted in writing to Tripp Lite within 30 days of the occurrence or the claim will not be considered.
This warranty does not include damage resulting from accident or misuse, and applies to the domestic
(USA & Canada) use of these products only. Tripp Lite reserves the right to determine whether the
damage to the connected equipment is due to malfunction of the Tripp Lite product by requesting
the equipment in question be sent to Tripp Lite for examination. This policy is above and beyond, only
to the extent needed, of that provided by any coverage of connected equipment provided by other
sources, including, but not limited to, any manufacturer’s warranty and/or any extended warranties.
EXCEPT AS PROVIDED ABOVE, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some
states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s)
or exclusion(s) may not apply to purchaser. EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP
LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Specifically, Tripp Lite is not liable for any costs, such as lost profits or revenue, loss of equipment,
loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties or
otherwise. Coverage also does not apply to connected medical and industrial equipment.
To receive service under this warranty, you must be the original purchaser/user of the product in
question. You must obtain a Returned Material Authorization (RMA) number from Tripp Lite. Products
must be returned to Tripp Lite with transportation charges prepaid and must be accompanied by a
brief description of the problem encountered and proof of date and place of purchase.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
17-01-038-933657.indb 13 1/5/2017 5:16:01 PM
14
Manual del Propietario
Estaciones de Carga
para Escritorio
Carga USB (Modelo: CSD1006USB)
Carga de CA con Supresión de Sobretensiones
(Modelo: CSD1006AC)
English 1 • Français 27
1111 W. 35th Street, Chicago, IL 60609 EE. UU. • www.tripplite.com/support
Copyright © 2017 Tripp Lite. Todos los derechos reservados.
Características del Producto 15
Contenido del Empaque 15
Accesorios Opcionales 16
Advertencias de Seguridad Importantes 16
Configuración 17
Carga USB 18
Carga de CA 21
Ajuste de los Divisores de Estante de 24
Almacenamiento (Todos los Modelos)
Especificaciones 25
Garantía 26
17-01-038-933657.indb 14 1/5/2017 5:16:01 PM
15
Características del Producto
Contenido del Empaque
Ambos Modelos
• Cargan hasta 10 tabletas, smartphones u otros dispositivos móviles.
• Funciona tanto como cargador USB o cargador AC y también como unidad de
almacenamiento, proporcionando espacio para organizar perfectamente sus
dispositivos mientras se cargan
• Los separadores removibles personalizan el espacio de almacenamiento de la
unidad de acuerdo al número y tamaño de los dispositivos que se estén cargando
Modelo CSD1006USB
• La carga rápida BC1.2 con un solo puerto es capaz de alimentar hasta 5V 2.4A
• La protección contra sobrecorriente evita que los dispositivos jalen más energía
que la que el cargador es capaz de soportar
• La protección contra sobrecarga detiene la carga cuando se completa la batería
del dispositivo
Modelo CSD1006AC
• Valor nominal de supresión de sobretensiones de 2880 joules
• Filtrado de ruidos EMI/RFI
• LED de diagnóstico indica Protegido (verde) y con Conexión a Tierra (rojo)
• El apagado automático corta la alimentación a los tomacorrientes cuando el
circuito de protección ha sido comprometido
• $100,000 Seguro Máximo de por Vida para el equipo conectado
(EE. UU., Canadá y Puerto Rico únicamente)
CSD1006USB
• Cargador USB
• Fuente de alimentación externa con
clavija 5-15P (Entrada: 100 ~ 240V,
50/60Hz, 2A; Salida Máxima:
12V, 8A)
• Gabinete con tapa asegurable
• Soporte del gabinete del cargador
USB
• Llaves
• Cable de seguridad de combinación
• Manual del Propietario
CSD1006AC
• Supresor de Sobretensiones de CA
con 10 Tomacorrientes
• Gabinete con tapa asegurable
• Llaves
• Cable de seguridad de combinación
• Manual del Propietario
17-01-038-933657.indb 15 1/5/2017 5:16:01 PM
16
Accesorios Opcionales
Advertencias de Seguridad Importantes
• Cables USB a Lightning
®
de la Serie M100
• Cables de 30 Pines de la Serie M110 USB a Apple
®
• Lea siempre con cuidado las instrucciones de seguridad.
• Conserve estas instrucciones para consulta futura.
• No lo instale cerca de fuentes de calor tales como radiadores, rejillas de
calefacción, calentadores u otros equipos (incluyendo amplificadores) que
produzcan calor.
• Desconecte la unidad cuando no se use por períodos prolongados.
• Para reducir el riesgo de incendio o descarga eléctrica, no exponga esta unidad a
la lluvia o humedad, incluyendo cualquier goteo o salpicadura.
• Objetos que contengan líquidos, como floreros, no deben colocarse nunca sobre
o cerca de la unidad.
• La unidad presenta un riesgo de descarga eléctrica; no la abra.
• El tomacorrientes usado para alimentar la unidad debe ser fácilmente accesible y
ubicarse cerca del equipo.
• El cable de alimentación es solo para uso en interiores.
•
La temperatura ambiente máxima alrededor de la unidad no debe exceder los 40°C
[104°F].
• La clavija del cable de alimentación y la entrada se usan como dispositivo
de desconexión para la unidad y sus periféricos conectados. El cable de
alimentación debe ser fácilmente accesible durante la operación.
• Consute la etiqueta de identificación en la unidad para ver las especificaciones
de entrada y salida. No sobrecargue la fuente de alimentación.
• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en
donde la falla de este equipo pueda razonablemente causar la falla del equipo de
soporte de vida o afectar significativamente su seguridad o efectividad.
17-01-038-933657.indb 16 1/5/2017 5:16:01 PM
17
Ensamble
Ambos Modelos
1
Después de retirar el empaque protector, coloque la caja separada en
la parte posterior de la unidad del gabinete que contiene al cargador de
USB o el supresor de sobretensiones de CA. Extráigalo de la caja.
2
Retire la tapa del gabinete empujándola y levantándola.
17-01-038-933657.indb 17 1/5/2017 5:16:02 PM
18
Ensamble
3
Levante y retire el estante de almacenamiento del gabinete.
4
Fije la unidad de carga en el gabinete:
Modelo CSD1006USB
A
Deslice el soporte de instalación incluido en las ranuras posteriores del
gabinete.
17-01-038-933657.indb 18 1/5/2017 5:16:02 PM
19
Ensamble
Modelo CSD1006USB (continuación)
B
Inserte la unidad de carga USB en el soporte de instalación con los puertos
USB viendo hacia arriba.
C
Conecte los cables de carga USB apropiados para el número y tipo de
dispositivos. Las ranuras ubicadas en la parte superior y frontal de la base del
gabinete permiten la adecuada conducción del cableado.
17-01-038-933657.indb 19 1/5/2017 5:16:02 PM
20
Ensamble
Modelo CSD1006USB (continuación)
D
Una vez conectados todos los cables USB deseados, coloque el estante de
almacenamiento en la parte superior de la base del gabinete.
Nota: Para retirar o ajustar
los divisores del estante
de almacenamiento,
consulte la página 24.
E
Conecte los dispositivos electrónicos a los cables de alimentación USB y
coloque las unidades a cargar dentro del estante de almacenamiento.
F
Use la fuente de alimentación incluida para conectar la unidad de carga a un
supresor de sobretensiones de Tripp Lite o un tomacorrientes de pared de CA.
G
Proceda al paso 5.
17-01-038-933657.indb 20 1/5/2017 5:16:03 PM
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
