Cafe CYE22TSHSS Owner's manual

GEAppliances.com

Refrigerators

Bottom Freezer

239D3389P008 Pub No. 49-60713-1 09-14 GE

Write the model and serial

numbers here:

Model # ____________________

Serial # ____________________

Find these numbers on a label

on the left side, near the middle

of the refrigerator compartment.

GE Café™ models

Owner’s Manual and

Installation Instructions

Models that start with CFE are

Standard Depth Models (SD)

Models that start with CYE and CWE

are Counter Depth Models (CD)

Safety Instructions ............2-4

Operating Instructions

Features ..........................5, 6

Controls ..........................7, 8

Odor Remover ......................9

Dispenser ..........................10

Hot Water .........................11

Water Filter ........................12

Fresh Food Storage Options .....13,14

Climate Zone & Temperature

Controlled Drawer ...............15,16

Freezer ............................17

Automatic Ice maker ...............18

Care and Cleaning ................ 19

Replacing the Lights ................20

Installation Instructions

Preparing to Install the

Refrigerator ....................21, 22

Installing the Anti-Tip Bracket . . . 29, 30

Installing the Refrigerator .......23–33

Installing the Water Line ........34-35

Troubleshooting Tips ......38, 39

Normal Operating Conditions .......37

Service - Truth or Myth .........40, 41

Consumer Support

Warranty ..........................42

RPWFE Water Filter Cartridge Limited

Warranty ........................43

Performance Data Sheet ...........44

Consumer Support ........Back Cover

Modèles GE Café™

Manuel d’utilisation

et instructions

d’installation

Les numéros de modèle commençant par

CFE sont des modèles de profondeur normale

(PN).

Les numéros de modèle commençant par

CYE et CWE sont des modèles de profondeur

de comptoir (PC).

Réfrigérateurs

Modelos GE Café

TM

Manual del Propietario

e Instrucciones de

Instalación

Los modelos que comienzan con las letras

CFE son Modelos con Profundidad Estándar

(SD)

Los modelos que comienzan con las letras

CYE y CWE son Modelos con Profundidad de

Mesada (CD)

Refrigeradores

La section française commence à la

page 47

La sección en español empieza en la

página 93

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

2

IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING

GE Appliances website

For more information on your refrigerator’s operation, visit

www.GEAppliances.com In Canada visit GEAppliances.ca or call 800.561.3344.

 This refrigerator must be properly installed and located in

accordance with the Installation Instructions before it is

used.

 Unplug the refrigerator before cleaning and making repairs.

 NOTE: Repairs must be performed by a qualified Service

Professional.

 Replace all parts and panels before operating.

 Because of potential safety hazards under certain

conditions, we strongly recommend against the use of an

extension cord. However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA certified (in Canada), 3-wire grounding type

appliance extension cord having a grounding type plug

and outlet and that the electrical rating of the cord be 15

amperes (minimum) and 120 volts.

 To prevent suffocation and entrapment hazards to children,

Remove the fresh food and freezer doors from any

refrigerator before disposing of it or discontinuing its use.

 Do not store or use gasoline or other flammable vapors and

liquids in the vicinity of this or any other appliance.

 Power to the refrigerator cannot be disconnected by

any setting on the control panel, refrigerator must be

unplugged to remove power.

 Do not allow children to climb, stand or hang on the door

handles or the shelves in the refrigerator. They could

seriously injure themselves.

 In refrigerators with automatic ice makers, avoid contact

with the moving parts of the ejector mechanism, or with

the heating element that releases the cubes. Do not place

fingers or hands on the automatic ice making mechanism

while the refrigerator is plugged in.

 Do not clean glass shelves or covers with warm water

when they are cold. Glass shelves and covers may break if

exposed to sudden temperature changes or impact, such

as bumping or dropping. Tempered glass is designed to

shatter into many small pieces if it breaks.

 Keep fingers out of the “pinch point” areas; clearances

between the doors and between the doors and cabinet are

necessarily small. Be careful closing doors when children are

in the area.

 Do not touch the cold surfaces in the freezer compartment

when hands are damp or wet., skin may stick to these

extremely cold surfaces.

 Do not refreeze frozen foods which have thawed completely.

 Use a sturdy glass when dispensing ice (on models with ice

dispenser)

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety

messages will follow the safety alert symbol and the word “DANGER”, “WARNING”, or “CAUTION”. These words are defined as:

Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, explosion, electric shock, or injury when using your

refrigerator follow these basic safety precautions:

REFRIGERATOR SAFETY INFORMATION

SAFETY

WARNING

DANGER

CAUTION

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING. GEAppliances.com

3

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from refrigerator. Failure to do so can

result in fire, explosion, or death.

WARNING

Tip Over Hazard.

Built-in style models (model PYE, CYE, GYE, PWE, CWE, and ZWE) are top heavy, especially with any doors

open. These models must be secured with the anti-tip floor bracket to prevent tipping forward, which

could result in death or serious injury. Read and follow the entire installation instructions for installing

the anti-tip floor bracket packed with your refrigerator.

INSTALLATION

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong

(grounding) plug which mates with a standard 3-prong

(grounding) wall outlet to minimize the possibility of electric

shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is

your personal responsibility and obligation to have it replaced

with a properly grounded 3-prong wall outlet. Do not use an

adapter.

The refrigerator should always be plugged into its own

individual electrical outlet which has a voltage rating that

matches the rating plate.

A 115 Volt AC, 60 Hz, 15- or 20-amp fused, grounded

electrical supply is required. This provides the best

performance and also prevents overloading house wiring

circuits which could cause a fire hazard from overheated

wires.

Never unplug your refrigerator by pulling on the power cord.

Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have

become frayed or otherwise damaged. Do not use a cord

that shows cracks or abrasion damage along its length or at

either end.

When moving the refrigerator away from the wall, be careful

not to roll over or damage the power cord.

CONNECTING ELECTRICITY

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet

Do not remove the ground prong

Do not use an adapter

Failure to follow these instructions can result in death, fire, or electrical shock.

SAFETY (CONT.)

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING

Suffocation and child entrapment hazard.

Remove fresh-food and freezer doors from the refrigerator, prior to disposal. Failure to do so can

result in child entrapment which can lead to death or brain damage.

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous even if they will sit for “just a few days.”

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or

Freezer:

 Take off the fresh food and freezer doors.

 Leave the shelves in place so that children may not

easily climb inside.

Refrigerants

All refrigeration products contain refrigerants, which

under federal law must be removed prior to product

disposal. If you are getting rid of an old refrigeration

product, check with the company handling the disposal

about what to do.

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

IMPORTANT:

SAFETY (CONT.)

WARNING

Scalding Hazard.

The hot water dispenser is capable of heating water to a temperature of approximately 185°F (85°C).

Water temperatures above 125°F (52°C) can cause severe burns or death from scalding. Children, the

disabled, and the elderly are at highest risk of being scalded.

 The water coming from the dispenser is very hot. Use

extreme caution when dispensing and drinking water. Allow

water to cool to a drinkable temperature before drinking.

 When dispensing water below 125ÛF, always test the

temperature of the water before drinking.

 When dispensing hot water, the container can become

very hot. Use a temperature insulating container, such

as ceramic or Styrofoam. Using container materials such

as paper or plastic may result in a burn while holding the

cup. Do not use glass containers, as thermal shock can

cause the container to break and may result in scalding or

lacerations.

 Do not permit children to use the hot water dispenser.

 The hot water dispensing knob requires both twist and

push motions in order to reduce the risk of hot water being

dispensed unintentionally or by small children. Do not

tamper with or modify the hot water dispensing knob.

 Always follow the formula manufacturer’s instructions for

preparation of baby formula.

 Hold your cup or container close to the dispensing point to

minimize splashing of hot water that could contact your

hand. Do not dispense hot water into a cup resting on the

dispenser tray, as this will increase water splash.

 Do not use with water that is microbiologically unsafe or of

unknown quality.

 The hot water dispenser is designed to only dispense water.

Do not attempt to heat or dispense anything other than

water. Do not attempt to disassemble or clean the tank.

 A newly installed water filter cartridge will cause water to

spurt from the dispenser. Run 2 gallons of water through

the cold water dispenser (about 5 minutes) to remove air

from the system. Until this air is removed from the system

through the cold water dispenser, DO NOT use the hot water

dispenser as it may result in spurting of hot water and lead

to hot water scalding.

 The hot water dispensing tank is a non-pressurized tank,

with a vent on the tank and a dispenser tube outlet. Do

not modify the system, close or block the dispense tube, or

connect any other type of device to the tank or dispense

tube. Doing so may lead to rupture of the tank and hot

water scalding.

Use this appliance only for its intended purpose as described in this Owner’s Manual. To reduce the risk of severe burns,

scald injuries, or death when using your hot water dispenser, the instructions below must be followed:

HOT WATER DISPENSER

Space-saving ice maker*

Ice maker and bin are located on the door creating

more usable storage space.

Showcase LED lighting

LED lighting is positioned throughout the interior to

spotlight areas in the refrigerator. LEDs are located

under the fresh food door to light the freezer when

opened.

Drop-down tray*

Allows for extra door storage when you need it and

tucks away when you don’t.

Full-width temperature controlled drawer

Adjustable temperature control bin that can accommo-

date larger items.

Dairy bin

Separate compartment for your items.

Ice bin/Ice maker*

Ice maker with ice storage bins.

QuickSpace™ shelf*

Functions as a normal full-sized shelf when needed and

easily slides back to store tall items below.

Spillproof shelves

Designed to capture your spills for easier clean up.

Anti-slip Mat

Liner that captures spills, keeps containers from shifting

when the door is opened and is easily removable for

cleaning.

Removable door bin

Can be removed for those with a wall limiting the door

opening.

Climate zone bin

Separate bins for produce storage.

Water filter

Filters water and ice.

5

About the features. GEAppliances.com

* Select models only.

6

Door ice bin*

1. Open left fresh food door.

2. Pull down latch to release bin

door.

3. Using handhold lift ice bucket up

and out to clear locators in bot-

tom of bin.

4. To replace the ice bucket, set

it on the guide brackets and

push until the ice bucket seats

properly.

5. If bucket cannot be replaced,

rotate the Ice Bucket Fork 1/4

turn clockwise.

Drop down dairy bin*

1. Open right fresh food door.

2. Depress both buttons on lower

sides and bin will drop down.

3. Reverse to reinstall.

Ice/water filter

Remove filter/bypass plug

Push the indent on the cover and

open filter door. Pull out on filter/

bypass plug and pull straight back

to remove.

Installing the filter cartridge

Push the indent at the bottom of

the cover and open. Lift door and

align tabs on filter to filter/holder

and push filter into place.

Drop tray

(tray open)

Push in and

pull open

Ice bucket

Latch

About the features .

*Select Models Only

Swing

Push \ Pull

1

2

7

About the controls with temperature settings. GEAppliances.com

Temperature Express Modes Settings

Water

Lock

Controls

Precise

Fill

Hot

Water

Light

Water Crushed Cubed

NOTE: For optimal temperature performance, we

recommend to avoid placing food or other items directly

at the air flow vents or the fresh food air tower, thus

blocking the air flow.

Changing the Temperature for Control Style CYE/CFE

To Change the Refrigerator Temperature:

Access By: Temperature Button

Temperature

Activate By: Below the word “Refrigerator”, use the arrows to select the

desired temperature. Press DONE when finished to return to HOME screen.

To Change the Freezer Temperature:

Access By: Temperature Button

Temperature

Activate By: Below the word “Freezer”, use the arrows to select the desired

temperature. Press DONE when finished to return to HOME screen.

To turn OFF cooling system, access SETTINGS from the HOME screen. Page

over and tap COOLING SYSTEM ON. Press DONE to return to HOME screen.

To turn ON cooling system, access SETTINGS from the HOME screen. Page

over and tap COOLING SYSTEM OFF. Press DONE to return to HOME screen.

Turning the cooling system off stops the cooling to refrigerator, but it does

not shut off the electrical power.

CYE/CFE Control Style CWE Control Style

Refrigerator

Hold 3 Sec for °F/°C

Hold 3 Seconds

Recommended: 37 °F

Actual Set

Energy Smart

Energy Smart Override

Hold 3 Seconds

Freezer

Door Alarm

Ice Maker

Lock Controls

Reset Filter

Recommended: 0°F

F

Changing Temp. for Control Style CWE

Temperature Display is located on inside of left-hand

refrigerator door. To change the temperature, press and

release the REFRIGERATOR or FREEZER pad. The ACTUAL

TEMP light will come on and the display will show the actual

temperature. To change the temperature, tap either the

REFRIGERATOR or FREEZER pad until the desired

temperature is displayed.

To turn OFF cooling system, press and hold the

REFRIGERATOR and FREEZER pads simultaneously for 3

seconds. When the cooling system is OFF the display should

read OFF.

To turn ON cooling system, press either REFRIGERATOR or

FREEZER pad. The display will show the preset temperature

settings of 37°F for refrigerator and 0°F for freezer. Turning

the cooling system off stops the cooling to refrigerator, but it

does not shut off the electrical power.

About the controls features.

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer

compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and

freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment.

NOTE: The refrigerator is shipped with protective film covering the temperature

controls. If this film was not removed during installation, remove it now.

8

Temperature Express Modes Settings

Water

Lock

Controls

Precise

Fill

Hot

Water

Light

Water Crushed Cubed

Hot Water

Dispenses up to 10 ounces of filtered hot water from user

selected ranges of 90°F to 185°F.

Hot Water Knob

Illuminates to indicate hot water is ready. Dispenses with two

motions: a counter-clockwise twist and then push to dispense.

Precise Fill

Precisely dispenses filtered water in accurate measurements

in ounces, cups, quarts, or liters using paddle.

Refrigerator temp control

Adjust freezer compartment temperature.

Fresh food temp control

Adjust fresh food compartment temperature.

TurboFreeze™ setting

Activate TurboFreeze to quickly restore freezer

temperatures after frequent door openings.

TurboCool™ setting

Activate TurboCool to quickly restore fresh food temperature after

frequent door openings.

Humidity setting

Humidity setting can be normal or high.

Lock controls

Press and hold 3 seconds to lock out ice and water dispenser

and all feature and temperature buttons.

LED dispenser light

LED lighting that can be turned on/off to light your dispenser.

Photo Upload

Insert USB memory stick to upload personal photos to the

refrigerator LCD screen. LCD will provide on screen prompts to

load and view slideshow. Make sure the photos are in the root

directory in your USB.

Additional Settings

• Connected Home ready

• Slideshow

• Reset filter

• Ice maker on/off

• Door alarm

• Sound control

• Cooling system On/Off

• Metric/English units

Additional Modes

• Sabbath Mode

Press and hold lock & light simultaneously for 3 seconds to

enter/exit Sabbath mode.

Activate Sabbath Mode to turn off interior lights, tempera-

ture control and advanced features. Compressor will run on

a timed defrost when in Sabbath mode.

Control Style A, External Controls

CFE/CYE Models

Refrigerator

Hold 3 Sec for °F/°C

Hold 3 Seconds

Recommended: 37 °F

Actual Set

Energy Smart

Energy Smart Override

Hold 3 Seconds

Freezer

Door Alarm

Ice Maker

Lock Controls

Reset Filter

Recommended: 0°F

F

Controls Style B, Internal Controls

CWE Models

Door Alarm

Sounds to alert when the freezer or fresh food doors

have been left open.

Reset Filter

Hold for 3 seconds after replacing filter.

Lock Controls

Press and hold 3 seconds to lock out ice and water

dispenser and all feature and temperature buttons.

Freezer temp control

Adjust freezer compartment temperature

Refrigerator temp control

Adjust fresh food compartment temperature

Ice maker setting

Turn your ice makers on/off.

GEAppliances.com

9

10

About the dispenser. (CFE & CYE Models Only)

Dispenser tray

Important Facts About Your Dispenser



Do not add ice from trays or bags to the door ice maker

bucket. It may not crush or dispense.



Avoid overfilling glass with ice and use of narrow glasses.

Backed-up ice can jam the chute or cause the door in the

chute to freeze shut. If ice is blocking the chute remove the ice

bucket, poke it through with a wooden spoon.



Beverages and foods should not be quick-chilled in the

door ice maker bin. Cans, bottles or food packages in the

storage drawer may cause the ice maker or auger to jam.



To keep dispensed ice from missing the glass, put the glass

close to, but not touching, the dispenser opening.



Some crushed ice may be dispensed even though you

selected CUBED ICE. This happens occasionally when a few

cubes accidentally get directed to the crusher.



After crushed ice is dispensed, some water may drip from the

chute.



Sometimes a small mound of snow will form on the door in the

ice chute. This condition is normal and usually occurs when you

have dispensed crushed ice repeatedly. The snow will eventually

evaporate.

If no water is dispensed when the refrigerator is first installed,

there may be air in the water line system. Press the dispenser

paddle for at least five minutes to remove trapped air from the

water line and to fill the water system. To flush out impurities in

the water line, throw away the first six full glasses of water.

To remove Dispenser Tray



Pull Dispenser Tray out until it stops.



Locate tab in the center on the bottom and push up.



Pull Dispenser Tray assembly out.



Lift metal Dispenser Tray out at center notch to clean.

To reinstall Dispenser Tray



Place the Dispenser Tray cover on top of catch tray and

position under the two plastic retainers on either side.



Center Dispenser tray, and align with center guides.



Push in until is firmly in place.

Water & Ice Dispenser

(See About the controls

with temperature settings &

About the control features)

To Use the Internal Water Dispenser (CWE Models Only)

The water dispenser is located on

the left wall inside the refrigerator

compartment.

To dispense water:

Hold the glass against the recess.

Push the water dispenser button.

Hold the glass underneath the

dispenser for 2–3 seconds after

releasing the dispenser button. Water

may continue to dispense after the

button is released.

If no water is dispensed when the refrigerator is first installed,

there may be air in the water line system. Press the dispenser

button for at least 5 minutes to remove trapped air from the

water line and to fill the water system. During this process,

the dispenser noise may be loud as the air is purged from the

water line system. To flush out impurities in the water line,

throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser should be

cleaned periodically by wiping with a clean cloth or sponge.

WARNING

Laceration Hazard

 Never put fingers or any other object into ice crusher

discharge opening. Doing so can result in contacting the ice

crushing blades and lead to serious injury or amputation

 Use a sturdy glass when dispensing ice. A delicate glass may

break and result in personal injury.

11

About Hot Water. (CFE & CYE Models Only)

GEAppliances.com

To Use Hot Water Dispenser

• Press HOT WATER button.

• Select desired water temperature on the LCD screen (90, 150,

170, 185, or Custom).

• When hot water is ready (indicated on the screen and by a

beeping sound) hold container with left hand centered in the

recess under the spout.

• To dispense water, rotate the hot water knob counterclockwise

and then push it in. The knob must be held in during dispense.

Important Facts about HOT WATER

•

WARNING

Scalding Hazard.

The water coming from the dispenser is very hot and can cause

scalds or burns. Read all warnings prior to use. (See page 4.)

• Always use a container that is suitable for hot liquids (ceramic,

styrofoam, etc.)

• The maximum single hot water dispense amount is 10 oz.

Additional hot water can be dispensed by restarting the hot

water feature through the LCD screen.

• HOT WATER works best with household water pressure of 40 to

100 psi.

• HOT WATER will time out if unused and may require a short

reheat time.

Temperature Express Modes Settings

Water

Lock

Controls

Precise

Fill

Hot

Water

Light

Water Crushed Cubed

About the GE

®

RPWFE water filter cartridge.

12

*Select Models Only

Water Filter Cartridge

The water filter cartridge is located in the fresh food interior

on the left side wall, near the top.

This product uses radio frequency identification (RFID) to

detect leaks and monitor filter status. The RFID technology is

certified by the FCC.

When to replace the filter cartridge

The filter cartridge should be replaced every six months or

earlier if 170 gallons of water has been dispensed or the flow of

water to the dispenser or icemaker decreases.

Touch Screen Models: A filter status message will appear on

the screen when the water filter needs to be replaced. The filter

status will automatically update when the filter is replaced.

Non-touch Screen Models: A filter indicator light will illuminate

on the screen when the water filter needs to be replaced.

Removing the filter cartridge

To replace the filter, first remove the old cartridge by opening

the filter door and pulling on the bottom of the cartridge to allow

it to swing outward. When the cartridge can no longer swing,

gently pull to unseat it from the cartridge holder. DO NOT TWIST

CARTRIDGE. A small amount of water may drip out.

Installing the Filter Cartridge

1. Align top of filter cartridge with cartridge holder with the word

“FRONT” facing outward then push the cartridge toward

the rear of the unit until it is fully seated. DO NOT TWIST THE

FILTER CARTRIDGE!

2. While continuing to ensure cartridge is fully seated in the

holder, gently swing the filter inward until it is in position. If

filter will not swing easily, check to ensure filter is properly

aligned and fully seated within the cartridge holder. Close the

filter door.

3. Run two gallons of water through the cold water dispenser

(about 5 minutes) to remove air from the system. A newly

installed filter cartridge will cause water to spurt from the

dispenser. Use a large pitcher or sports bottle to catch the

water spray. DO NOT use hands-free auto-fill (some models)

until all air is removed from the system.

4. Reset Filter Status message (non-touch screen models).

WARNING

Scalding Hazard.*

Use of the hot water dispenser prior to purging air from the

system may result in spurting of hot water and lead to hot water

scalding. Follow the instructions above to purge all air from the

system through the cold water dispenser prior to using the hot

water dispenser.

Note: It is normal for water to appear discolored during the initial

system flush. Water color will return to normal after first few

minutes of dispensing.

Filter Bypass Plug

To reduce the risk of property damage due to water leakage,

you MUST use the filter bypass plug when a replacement filter

cartridge is not available. The dispenser and icemaker will not

operate without either the filter or bypass plug installed. The

bypass plug is installed in the same way as a filter cartridge.

FCCID: ZKJ-EBX1532P001 ICID: 10229A-EBX1532P001

“This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.”

“This device complies with Industry Canada licence-exempt

RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2)

this device must accept any interference, including interference

that may cause undesired operation of the device.”

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to have access to small parts

during the installation of this product. The disposable filter cartridge should be replaced every 6 months at the rated capacity,

or sooner if a noticeable reduction in flow rate occurs.

For the maximum benefit of your filtration system, GE recommends the use of GE-branded filters only. Using GE-branded filters

in GE and Hotpoint

®

refrigerators provides optimal performance and reliability. GE filters meet rigorous industry NSF standards

for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE-branded filters

for use in GE and Hotpoint refrigerators and there is no assurance that non-GE-branded filters meet GE’s standards for quality,

performance and reliability.

If you have questions, or to order additional filter cartridges, visit our website at www.geapplianceparts.com or call GE

Parts and Accessories, 800.626.2002.

Customers in Canada should consult the yellow pages for the nearest Camco Service Center.

Swing

Push \ Pull

13

Rearranging the Shelves

To remove:

Remove all items from the shelf.

Tilt the shelf up at the front.

Lift the shelf up at the back and bring the

shelf out.

To replace:

While tilting the shelf up, insert the top hook

at the back of the shelf in a slot on the

track.

Lower the front of the shelf until the bottom

of the shelf locks into place.

Spillproof Shelves

Spillproof shelves have special edges to help

prevent spills from dripping to lower shelves.

Shelves in the refrigerator compartment are adjustable.

Quick Space Shelf *

This shelf splits in half and slides under itself for

storage of tall items on the shelf below.

This shelf can be removed and replaced or

relocated (just like spillproof shelves).

NOTE: The back half of the Quick Space Shelf is

not adjustable.

About the fresh food storage options. GEAppliances.com

*Select Models Only

14

About the fresh food storage options.

Non-Adjustable Bins on the Door (Dispenser Models - Left Hand Door)

To remove: Lift the bin straight up, then pull

out.

To replace: Engage the bin in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then pull out.

To replace or relocate: Slide in the bin just

above the molded door supports, and push

down. The bin will lock in place (see page 33).

Non-Adjustable Dairy Bin*

To remove: Lift the dairy bin straight up,

then pull out.

To replace: Engage the bin in the molded door

supports and push down. The bin will lock in

place. See page 33.

Drop down tray *

(tray open)

1. Open right fresh food

door

2. Depress both buttons

on lower sides of bin

and bin will drop down.

3. Reverse to reinstall.

The ice maker door bins are not

interchangeable, note the location upon

removal and replace the bin in its proper

location.

*Select Models Only

Non-Dispense Models

(Left Hand Door)

ClimateZone

Temperature Controlled Drawer

The Temperature Controlled Drawer is a

full-width drawer with adjustable temperature

control. This drawer can be used for large

miscellaneous items.

To change setting, press select button.

Keep fruits and vegetables organized in

separate compartments for easy access.

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

15

About the climate zone and temperature

controlled drawer. GEAppliances.com

32° 34° 38°

Note: Temperatures indicate the appropriate tem-

peratures for the food and actual temperatures may

vary based on normal operation and other factors

such as door openings and fresh food set point.

CAUTION

Laceration Hazard.

Do not store glass bottles at this setting. If

they are frozen, they can break and result

in personal injury.

Meat Beverage Deli

Select

To remove:

Pull the drawer out to the stop position.

Lift the front of the drawer up and out.

To replace:

Pull left and right slides until fully extended.

Place drawer back in first and rotate drawer

front down to seat on slide.

Push the drawer in to closed position.

How to Remove and Replace the Adjustable Deli/Produce Drawer

To remove:

Pull the drawer out to the stop position.

Slide pan divider to right to release it from

pan.

To replace:

Reverse steps 1 and 2 to replace drawer

divider.

How to Remove and Replace Drawer Divider*

About the climate zone and temperature controlled drawer.

16

*Select Models Only

17

About the freezer. GEAppliances.com

Freezer Basket and Drawer

Basket.

Drawer

Ice Bucket*

Non-Adjustable Bin in the Freezer

To remove: push in plastic tab on either left or

right side

To replace: slide bin into location until it

locks into place.

Basket Removal

To remove, CFE only:

Open freezer door to the stop position.

Remove freezer door bin by pushing

plastic tab on either left or right side to

release bin hinge pin.

Remove freezer basket by lifting up the

rear of the basket and moving basket

rearward until the front of the basket

can be rotated upward and out.

Lift it out to remove.

To remove, CYE and CWE only:

Open fresh food doors.

Open freezer doorto the stop position.

Remove freezer basket by lifting up the

rear of the basket and rotate it

upward.

Lift it out to remove.

To replace:

Reverse step 1 thru 4 to replace.

*Select Models Only

18

About the automatic ice maker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Ice maker (on some models)

The ice maker will produce seven cubes

per cycle approximately 100–130 cubes

in a 24-hour period, depending on freezer

compartment temperature, room temperature,

number of door openings and other use

conditions.

The ice maker will fill with water when it cools to

15°F (–10°C). A newly installed refrigerator may

take 12 to 24 hours to begin making ice cubes.

If the refrigerator is operated before the water

line connection is made to the unit or if the

water supply to an operating refrigerator is

turned off, make sure that the ice maker is

turned off. Once the water has been connected

to the refrigerator, the ice maker may be turned

on. See the table below for details.

You may hear a buzzing sound each time the

ice maker fills with water.

Throw away the first few batches of ice to allow

the water line to clear.

Be sure nothing interferes with the sweep of the

feeler arm.

When the bin fills to the level of the feeler

arm, the ice maker will stop producing ice. It is

normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale and shrink.

NOTE: In homes with lower-than-average water

pressure, you may hear the ice maker cycle

multiple times when making one batch of ice.

Lift and pull

Ice Box

Door

Ice Bucket and Dispenser*

• Open the ice box door on inside of the left

door.

• Pull up and out on on the ice bucket in

the left hand door to remove it from the

compartment .

• To replace the ice bucket, set it on the

guide brackets and push until the ice

bucket seats properly.

• If bucket cannot be replaced, rotate the ice

bucket fork 1/4 turn clockwise.

Freezer Ice Bucket*

The ice storage is in the freezer compartment

drawer.

• Open the freezer drawer.

• The ice bucket is located on the left side of

the upper basket.

• Pull the upper basket forward to remove

the ice bucket.

Feeler Arm

Ice maker

Display Type (See Page 7) Model # How to turn the ice maker on/off

Control Style A CYE/CFE Use the settings menu on the touchscreen

Control Style B CWE Use the “ICE MAKER” button on the control

How to Turn the Ice Maker On/Off

WARNING

To minimize the risk of personal injury, avoid contact with the moving parts of the ejector

mechanism, or with the heating element that releases the cubes. Do not place fingers or

hands on the automatic ice making mechanism while the refrigerator is plugged in.

Freezer

Ice

Bucket

19

Care and cleaning of the refrigerator. GEAppliances.com

Cleaning the Outside

The stainless steel panels, door handles and trim.

Do not use appliance wax, polish, bleach, or other products

containing chlorine on stainless steel.

Stainless steel can be cleaned with a commercially available

stainless steel cleaner. A spray-on stainless steel cleaner

works best.

Silver-accented plastic parts.

Wash parts with soap or other mild detergents. Wipe clean with

a sponge, damp cloth or paper towel.

Do not use scouring pads, powdered cleaners, bleach or

cleaners containing bleach because these products can

scratch and weaken the paint finish.

Should spill tray need cleaning use lime remover.

Cleaning the Inside

Unplug the refrigerator before cleaning.

If this is not practical, wring excess moisture out of sponge or

cloth when cleaning around switches, lights or controls.

Use an appliance wax polish on the inside surface between

the doors.

8VHZDUPZDWHUDQGEDNLQJVRGDVROXWLRQ³DERXWD

tablespoon (15 ml) of baking soda to a quart (1 liter) of water.

This both cleans and neutralizes odors. Rinse and wipe dry.

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All

types of floor coverings can be damaged, particularly cushioned

coverings and those with embossed surfaces.

Raise the leveling legs located at the bottom front of the

refrigerator.

Pull the refrigerator straight out and return it to position by

pushing it straight in. Moving the refrigerator in a side direction

may result in damage to the floor covering or refrigerator.

Lower the leveling legs until they touch the floor.

When pushing the refrigerator back, make sure you don’t

roll over the power cord or water supply line.

For long vacations or absences, remove food and unplug the

refrigerator. Clean the interior with a baking soda solution of

one tablespoon (15 ml) of baking soda to one quart (1 liter) of

water. Leave the doors open.

LCD Models: turn refrigerator off at control (pg 7) .

If the temperature can drop below freezing, have a qualified

service technician drain the water supply system to prevent

serious property damage due to flooding.

1) Turn refrigerator off (pg. 7) or unplug the refrigerator.

2) Empty ice bucket

3) Turn water supply off

If you cut the water supply off, turn off the ice maker (pg. 18).

Upon returning from vacation:

1) Replace the water filter.

2) Run 2 gallons of water through the cold water dispenser

(about 5 minutes) to flush the system.

3) Dispense 185°F hot water 3 times (10 oz. each) to flush the

system.

Preparing for Vacation

Preparing to Move

Secure all loose items such as shelves and drawers by taping

them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest

the front or back of the refrigerator against the hand truck. This

could damage the refrigerator.

Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during

moving.

CAUTION

Do not clean glass shelves or covers

with warm water when they are cold. Glass shelves and

covers may break if exposed to sudden temperature

changes or impact such as bumping or dropping.

Tempered glass is designed to shatter into many small

pieces if it breaks.

20

Replacing the lights

Refrigerator Lights (LEDs)

There is LED lighting in fresh food

compartment and on the bottom of

the fresh food doors to light the freezer

compartment.

An authorized technician will need to

replace the LED light.

If this assembly needs to be replaced, call

GE Service at 1.800.432.2737

in the United States or 1.800.561.3344

in Canada.

Page is loading ...

Cafe CYE22TSHSS Owner's manual

This manual is also suitable for

Cafe CYE22TSHSS Owner's manual

in other languages

Related papers

Other documents