Leonard LI1326X User manual

Page is loading ...

CONTENTS

Safety information 37

Safety instructions 38

Product description 40

Control panel 41

Programmes 42

Settings 42

Before first use 44

Daily use 45

Hints and tips 46

Care and cleaning 47

Troubleshooting 49

Technical information 52

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damages that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Do not let children play with the appliance.

• Keep detergents away from children.

• Keep children and pets away from the appliance door

when it is open.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• This appliance is intended to be used in household and

similar applications such as:

– farm houses; staff kitchen areas in shops, offices and

other working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

Leonard 37

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum)

must be between 0.5 (0.05) / 8 (0.8) bar (MPa)

• Obey the maximum number of 13 place settings.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualified persons in order to avoid a hazard.

• Put knives and cutlery with sharp points in the cutlery

basket with the points down or in a horizontal position.

• Do not keep the appliance door open without supervision

to prevent to fall on it.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• The ventilation openings in the base (if applicable) must

not be obstructed by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

SAFETY INSTRUCTIONS

Installation

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Do not install or use the appliance

where the temperature is less than 0

°C.

• Follow the installation instruction

supplied with the appliance.

• Make sure that the appliance is

installed below and adjacent to safe

structures.

Electrical connection

WARNING! Risk of fire and

electrical shock.

• The appliance must be earthed.

• Make sure that the electrical

information on the rating plate agrees

with the power supply. If not, contact an

electrician.

• Always use a correctly installed

shockproof socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

38 Leonard

• This appliance complies with the E.E.C.

Directives.

• Only for UK and Ireland. The appliance

has a 13 amp mains plug. If it is

necessary to change the fuse in the

mains plug, use fuse: 13 amp ASTA

(BS 1362).

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

• The water inlet hose has a safety valve

and a sheath with an inner mains

cable.

WARNING! Dangerous

voltage.

• If the water inlet hose is damaged,

immediately close the water tap and

disconnect the mains plug from the

mains socket. Contact the Authorised

Service Centre to replace the water

inlet hose.

Use

• Do not sit or stand on the open door.

• Dishwasher detergents are dangerous.

Obey the safety instructions on the

detergent packaging.

• Do not drink and play with the water in

the appliance.

• Do not remove the dishes from the

appliance until the programme is

completed. There can be detergent on

the dishes.

• The appliance can release hot steam if

you open the door while a programme

operates.

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

Service

• Contact the Authorised Service Centre

to repair the appliance. We recommend

only the use of original spare parts.

• When you contact the Authorised

Service Centre, ensure that you have

the following information that is

available on the rating plate.

Model :

PNC :

Serial Number :

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent

children and pets to get closed in the

appliance.

Leonard 39

PRODUCT DESCRIPTION

4

3

7

9

8

10

56

11

1

2

1

Upper spray arm

2

Lower spray arm

3

Filters

4

Rating plate

5

Salt container

6

Air vent

7

Rinse aid dispenser

8

Detergent dispenser

9

Cutlery basket

10

Lower basket

11

Upper basket

40 Leonard

CONTROL PANEL

1 2

45

3

1

On/off indicator

2

Programme marker

3

Indicators

4

Start button

5

Programme knob

Indicators

Indicator Description

Washing phase. It comes on when the washing phase operates.

Drying phase. It comes on when the drying phase operates.

End indicator.

Salt indicator. It is always off while the programme operates.

Leonard 41

PROGRAMMES

Programme Degree of

soil

Type of load

Programme

phases

Consumption values

1)

Dura‐

tion

(min)

Energy

(kWh)

Water

(l)

2)

Normal soil

Crockery and

cutlery

• Prewash

• Wash 50 °C

• Rinses

• Dry

195 1.039 11

Normal soil

Crockery and

cutlery

• Prewash

• Wash 65 °C

• Rinses

• Dry

120 -

130

1.3 - 1.6 15 - 17

3)

Fresh soil

Crockery and

cutlery

• Wash 60 °C

or 65 °C

• Rinses

30 0.8 9

1)

The pressure and the temperature of the water, the variations of the mains supply, the options and the quantity

of dishes can change the values.

2)

With this programme you have the most efficient use of water and energy consumption for crockery and cutlery

with normal soil. (This is the standard programme for test institutes).

3)

With this programme you can wash a load with fresh soil. It gives good washing results in a short time.

Information for test institutes

For all the necessary information for test

performance, send an email to:

[email protected]

Write down the product number (PNC)

that is on the rating plate.

SETTINGS

Programme selection mode and

user mode

When the appliance is in programme

selection mode it is possible to set a

programme and to enter the user mode.

In user mode, the following settings

can be changed:

• The level of the water softener

according to the water hardness.

These settings will be saved until you

change them again.

How to set the programme

selection mode

The appliance is in programme selection

mode when the on/off indicator comes on

and start indicator starts to flash.

When you activate the appliance, usually

it is in programme selection mode.

However, if this does not happen, you can

set the programme selection mode in the

following way:

Press and hold Start until the start

indicator starts to flash.

42 Leonard

The water softener

The water softener removes minerals from

the water supply, which would have a

detrimental effect on the washing results

and on the appliance.

The higher the content of these minerals,

the harder your water is. Water hardness

is measured in equivalent scales.

The water softener should be adjusted

according to the hardness of the water in

your area. Your local water authority can

advise you on the hardness of the water in

your area. It is important to set the right

level of the water softener to assure good

washing results.

Water hardness

German de‐

grees (°dH)

French de‐

grees (°fH)

mmol/l Clarke de‐

grees

Water softener

level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

5

1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5

1

2)

1)

Factory setting.

2)

Do not use salt at this level.

Whether you use a standard detergent

or multi-tabs (with or without salt), set

the proper water hardness level to keep

the salt refill indicator active.

Multi-tabs containing salt are

not effective enough to soften

hard water.

How to set the water softener

level

The appliance must be in programme

selection mode.

1. Make sure that the programme marker

on the knob is aligned with the

indicator on/off .

2. To enter the user mode, turn the knob

counterclockwise until the symbol of

the first programme is aligned with the

on/off indicator. Press and hold the

Start until the indicators start , on/off

and start to flash.

• The intermittent flashing of

refers to the current set level, e.g. 5

flashes + pause + 5 flashes = level

5.

3. Press the Start button again and again

to change the setting. Each time you

press the Start button the level

number increases. After level 10 you

will start again from level 1.

4. Turn knob to on/off position to confirm

the setting.

Leonard 43

BEFORE FIRST USE

1. Make sure that the current level of

the water softener agrees with the

hardness of the water supply. If not,

adjust the level of the water

softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start a programme to remove any

processing residuals that can still be

inside the appliance. Do not use

detergent and do not load the baskets.

When you start a programme, the

appliance can take up to 5 minutes to

recharge the resin in the water softener. It

seems that the appliance is not working.

The washing phase starts only after this

procedure is completed. The procedure

will be repeated periodically.

The salt container

CAUTION! Only use salt

specifically designed for

dishwashers.

The salt is used to recharge the resin in

the water softener and to assure good

washing results in the daily use.

How to fill the salt container

1. Turn the cap of the salt container

counterclockwise and remove it.

2. Put 1 litre of water in the salt container

(Only for the first time).

3. Fill the salt container with dishwasher

salt.

4. Remove the salt around the opening of

the salt container.

5. Turn the cap of the salt container

clockwise to close the salt container.

CAUTION! Water and salt can

come out of the salt container

when you fill it. After you fill the

salt container, immediately

start a programme to prevent

corrosion.

How to fill the rinse aid

dispenser

M

A

X

1

2

3

4

+

-

A

B

D

C

E

CAUTION! Only use rinse aid

specifically designed for

dishwashers.

1. Press the release button (D) to open

the lid (C).

2. Pour the rinse aid in the dispenser (A)

until the liquid reaches the fill level

'max'.

3. Remove the spilled rinse aid with an

absorbent cloth to prevent too much

foam.

4. Close the lid. Make sure that the

release button locks into position.

44 Leonard

Fill the rinse aid dispenser

when the indicator (E)

becomes clear.

You can turn the selector of the

released quantity (B) between

position 1 (lowest quantity) and

position 4 or 6 (highest

quantity).

DAILY USE

1. Open the water tap.

2. Turn the knob until the symbol of the

programme you want to set is aligned

with the on/off indicator. Set the

correct programme for the type of load

and the degree of soil.

• If the salt indicators is on, fill the

salt container.

3. Load the baskets.

4. Add the detergent.

5. Start the programme.

Using the detergent

20

30

BA D

C

1. Press the release button (B) to open

the lid (C).

2. Put the detergent, in powder or tablets,

in the compartment (A).

3. If the programme has a prewash

phase, put a small quantity of

detergent in the compartment (D).

4. Close the lid. Make sure that the

release button locks into position.

Using the multi-tablets

When you use tablets, that contain salt

and rinse aid, do not fill the salt container

and the rinse aid dispenser.

1. Adjust the water softener to the lowest

level.

2. Set the rinse aid dispenser to the

lowest position.

Setting and starting a

programme

Starting a programme

1. Open the water tap.

2. Close the appliance door.

3. Turn the knob until the symbol of a

programme you want to set is aligned

with the on/off indicator.

• On/off indicator comes on.

• Start indicator starts to flash.

4. Press Start.

• The programme starts and the

indicator of the washing phase is

on.

• On/off indicator and start indicator

are on.

Opening the door while the

appliance operates

If you open the door while a programme is

running, the appliance stops. It may affect

the energy consumption and the

programme duration. When you close the

door, the appliance continues from the

point of interruption.

Cancelling the programme

Press and hold Start until the start

indicator starts to flash.

Make sure that there is detergent in the

detergent dispenser before you start a

new programme.

Leonard 45

End of the programme

When the programme is completed the

indicator is on. If you do not

deactivate the appliance within 5 minutes

all indicators goes off. This helps to

decrease energy consumption.

1. To deactivate the appliance, turn the

knob until the programme marker is

aligned with the on/off indicator.

2. Close the water tap.

HINTS AND TIPS

General

The following hints will ensure optimal

cleaning and drying results in daily use

and also help to protect the environment.

• Remove larger residues of food from

the dishes into the waste bin.

• Do not pre-rinse dishes by hand. When

needed, use the prewash programme

(if available) or select a programme

with a prewash phase.

• Always use the whole space of the

baskets.

• When loading the appliance, make sure

that the dishes can be completely

reached and washed by the water

released from the spray arm nozzles.

Make sure that items do not touch or

cover each other.

• You can use dishwasher detergent,

rinse aid and salt separately or you can

use the multi-tablets (e.g. ''3in1'',

''4in1'', ''All in 1''). Follow the

instructions written on the packaging.

• Select the programme according to the

type of load and degree of soil. With

the ECO programme you have the

most efficient use of water and energy

consumption for crockery and cutlery

with normal soil.

Using salt, rinse aid and

detergent

• Only use salt, rinse aid and detergent

for dishwasher. Other products can

cause damage to the appliance.

• In areas with hard and very hard water

we recommend to use plain dishwasher

detergent (powder, gel, tablets

containing no additional agents), rinse

aid and salt separately for optimal

cleaning and drying results.

• At least once a month run the

appliance with the use of appliance

cleaner which is particularly suitable for

this purpose.

• Detergent tablets do not fully dissolve

with short programmes. To prevent

detergent residues on the tableware,

we recommend that you use the tablets

with long programmes.

• Do not use more than the correct

quantity of detergent. Refer to the

instructions on the detergent

packaging.

What to do if you want to stop

using multi-tablets

Before you start to use separately

detergent, salt and rinse aid do the

following procedure.

1. Set the highest level of the water

softener.

2. Make sure that the salt and rinse aid

containers are full.

3. Start the shortest programme with a

rinsing phase. Do not add detergent

and do not load the baskets.

4. When the programme is completed,

adjust the water softener according to

the water hardness in your area.

5. Adjust the released quantity of rinse

aid.

Loading the baskets

• Only use the appliance to wash items

that are dishwasher-safe.

• Do not put in the appliance items made

of wood, horn, aluminium, pewter and

copper.

46 Leonard

• Do not put in the appliance items that

can absorb water (sponges, household

cloths).

• Remove larger residues of food from

the dishes into the waste bin.

• Make soft the remaining burned food

on the items.

• Put hollow items (cups, glasses and

pans) with the opening down.

• Make sure that glasses do not touch

other glasses.

• Put cutlery and small items in the

cutlery basket.

• Put light items in the upper basket.

Make sure that the items do not move.

• Make sure that the spray arms can

move freely before you start a

programme.

Before starting a programme

Make sure that:

• The filters are clean and correctly

installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is dishwasher salt and rinse aid

(unless you use multi- tablets).

• The position of the items in the baskets

is correct.

• The programme is applicable for the

type of load and for the degree of soil.

• The correct quantity of detergent is

used.

Unloading the baskets

1. Let the tableware cool down before

you remove it from the appliance. Hot

items can be easily damaged.

2. First remove items from the lower

basket, then from the upper basket.

At the end of the program

water can still remain on the

sides and on the door of the

appliance.

CARE AND CLEANING

WARNING! Before

maintenance, deactivate the

appliance and disconnect the

mains plug from the main

socket.

Dirty filters and clogged spray

arms decrease the washing

results. Make a check regularly

and, if necessary, clean them.

Cleaning the filters

The filter system is made of 3 parts.

C

B

A

1. Turn the filter (B) counterclockwise

and remove it.

Leonard 47

2. Remove the filter (C) out of filter (B).

3. Remove the flat filter (A).

4. Wash the filters.

5. Make sure that there are no residues

of food or soil in or around the edge of

the sump.

6. Put back in place the flat filter (A).

Make sure that it is correctly positioned

under the 2 guides.

7. Reassemble the filters (B) and (C).

8. Put back the filter (B) in the flat filter

(A). Turn it clockwise until it locks.

CAUTION! An incorrect

position of the filters can cause

bad washing results and

damage to the appliance.

Cleaning the spray arms

Do not remove the spray arms. If the holes

in the spray arms are clogged, remove

remaining parts of soil with a thin pointed

object.

External cleaning

• Clean the appliance with a moist soft

cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive

cleaning pads or solvents.

Internal cleaning

• Carefully clean the appliance, including

the rubber gasket of the door, with a

soft damp cloth.

48 Leonard

• If you regularly use short duration

programmes, these can leave deposits

of grease and limescale inside the

appliance. To prevent this, we

recommend to run long duration

programmes at least 2 times per

month.

• To maintain the performance of your

appliance at its best, we recommend to

use monthly a specific cleaning product

for dishwashers. Follow carefully the

instructions on the packaging of the

product.

TROUBLESHOOTING

If the appliance does not start or it stops

during operation, before you contact an

Authorised Service Centre, check if you

can solve the problem by yourself with the

help of the information in the table.

WARNING! Repairs not

properly done may result in

serious risk to the safety of the

user. Any repairs must be

performed by qualified

personnel.

With some problems the end indicator

flashes intermittently indicating a

malfunction.

The majority of problems that can

occur can be solved without the need

to contact an Authorised Service

Centre.

Problem and alarm code Possible cause and solution

You cannot activate the appliance. • Make sure that the mains plug is connected to

the mains socket.

• Make sure that there is no damaged fuse in the

fuse box.

The programme does not start. • Make sure that the appliance door is closed.

• Press Start.

• The appliance has started the procedure to re‐

charge the resin inside the water softener. The

duration of the procedure is approximately 5 mi‐

nutes.

The appliance does not fill with water.

• The end indicator flashes 1 time in‐

termittently.

• The Start indicator flashes continu‐

ously.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply

is not too low. For this information, contact your

local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not

clogged.

• Make sure that the inlet hose has no kinks or

bends.

Leonard 49

Problem and alarm code Possible cause and solution

The appliance does not drain the wa‐

ter.

• The end indicator flashes 2 times

intermittently.

• The Start indicator flashes continu‐

ously.

• Make sure that the sink spigot is not clogged.

• Make sure that the drain hose has no kinks or

bends.

The anti-flood device is on.

• The end indicator flashes 3 times

intermittently.

• The Start indicator flashes continu‐

ously.

• Close the water tap and contact an Authorised

Service Centre.

The appliance stops and starts more

times during operation.

• It is normal. It provides optimal cleaning results

and energy savings.

Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten

the adjustable feet (if applicable).

• The appliance door is not centred on the tub.

Adjust the rear foot (if applicable).

The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten

the adjustable feet (if applicable).

• Parts of the tableware are protruding from the

baskets.

Rattling/knocking sounds from inside

the appliance.

• The tableware is not properly arranged in the

baskets. Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

The appliance trips the circuit-beaker. • The amperage is insufficient to supply simulta‐

neously all the appliances in use. Check the

socket amperage and the capacity of the meter

or turn off one of the appliances in use.

• Internal electrical fault of the appliance. Contact

an Authorised Service Centre.

Refer to "Before first use",

"Daily use", or "Hints and

tips" for other possible causes.

Once you have checked the appliance,

press Start. If the problem occurs again,

contact an Authorised Service Centre.

For alarm codes not described in the

table, contact an Authorised Service

Centre.

50 Leonard

The washing and drying results are not satisfactory

Problem Possible cause and solution

Poor washing results. • Refer to "Daily use", "Hints and tips" and basket load‐

ing leaflet.

• Use more intensive washing programmes.

• Clean spray arm jets and filter. Refer to "Care and

Cleaning".

Poor drying results. • Tableware has been left for too long inside a closed ap‐

pliance.

• There is no rinse aid or the dosage of rinse aid is not

enough. Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• We recommend to always use rinse aid, even in combi‐

nation with multi-tablets.

There are whitish streaks or

bluish layers on glasses and

dishes.

• The release quantity of rinse aid is too much. Adjust the

rinse aid level to a lower level.

• The quantity of detergent is too much.

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Adjust

the rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

The dishes are wet. • The programme does not have a drying phase or has a

drying phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a

different brand or activate the rinse aid dispenser and

use rinse aid and multi-tablets together.

• Keep the dishwasher door ajar for some time before re‐

moving tableware.

The interior of the appliance is

wet.

• This is not a defect of the appliance. it is caused by the

humidity in the air that condenses on the walls.

Unusual foam during washing. • Use the detergent for dishwashers only.

• There is a leak in the rinse aid dispenser. Contact an

Authorised Service Centre.

Traces of rust on cutlery. • There is too much salt in the water used for washing.

Refer to "The water softener".

• Silver and stainless steel cutlery were placed together.

Avoid to put silver and stainless steel items close togeth‐

er.

Leonard 51

Problem Possible cause and solution

There are residues of deter‐

gent in the dispenser at the

end of the programme.

• The detergent tablet got stuck in the dispenser and

therefore was not completely washed away by water.

• Water cannot wash away the detergent from the dis‐

penser. Make sure that the spray arm is not blocked or

clogged.

• Make sure that items in the baskets do not impede the

lid of the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".

Limescale deposits on the ta‐

bleware, on the tub and on the

inside of the door.

• The level of salt is low, check the refill indicator.

• The cap of the salt container is loose.

• Your tap water is hard. Refer to "The water softener".

• Even using multi-functional tabs use salt and set regen‐

eration of the water softener. Refer to "The water soft‐

ener".

• If lime scale deposits still remain, clean the appliance

with appliance cleaners which are particularly suitable

for this purpose.

• Try different detergent.

• Contact the detergent manufacturer.

Dull, discoloured or chipped

tableware.

• Make sure that only dishwasher-safe items are washed

in the appliance.

• Load and unload the basket carefully. Refer to basket

loading leaflet.

• Place delicate items in the upper basket.

Refer to "Before first use",

"Daily use" or "Hints and

tips" for other possible causes.

TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575

Electrical connection

1)

Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply

Cold water or hot water

2)

max 60 °C

Capacity Place settings 13

Power consumption Left-on mode (W) 5.0

52 Leonard

Power consumption Off-mode (W) 0.50

1)

Refer to the rating plate for other values.

2)

If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water

supply to decrease energy consumption.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put

the packaging in relevant containers to

recycle it. Help protect the environment

and human health by recycling waste of

electrical and electronic appliances. Do

not dispose of appliances marked with the

symbol with the household waste.

Return the product to your local recycling

facility or contact your municipal office.

Leonard 53

*

Page is loading ...

Leonard LI1326X User manual

Leonard LI1326X User manual

in other languages

Related papers

Other documents