Gamber-Johnson 7160-0444 Specification
- Category
- Mounting kits
- Type
- Specification
Gamber-Johnson 7160-0444 is a Wiring Cover Plate designed for Ford Sedan & Utility vehicles equipped with the optional wiring kit. It covers the gap between the Gamber Johnson Console Box/Top Plate and wiring tunnel.
Key Features:
- Easy installation: Loosely install existing vehicle bolts into slots on legs of Wiring Cover Plate, align slots on vertical tab with holes in console box, and reattach arm rest assembly to clamp Wiring Cover Plate in place.
- Multiple mounting options: Can be attached directly to the console box using bolts, lock washers, and flat washers if an arm rest assembly is not used.
Gamber-Johnson 7160-0444 is a Wiring Cover Plate designed for Ford Sedan & Utility vehicles equipped with the optional wiring kit. It covers the gap between the Gamber Johnson Console Box/Top Plate and wiring tunnel.
Key Features:
- Easy installation: Loosely install existing vehicle bolts into slots on legs of Wiring Cover Plate, align slots on vertical tab with holes in console box, and reattach arm rest assembly to clamp Wiring Cover Plate in place.
- Multiple mounting options: Can be attached directly to the console box using bolts, lock washers, and flat washers if an arm rest assembly is not used.
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Rev.A
INST-580
Product Mounting Disclaimer
Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage
of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson
products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is
required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications
and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.
Wiring Tunnel
Gamber Johnson
Console Box
Existing Vehicle Bolt
Existing Vehicle Bolt
Gamber Johnson
Arm Rest Assembly
1/4-20 X 5/8
hex Head Bolt
INSTALLATION INSTRUCTIONS
Product
Revision
Form
If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868
Printing Spec:
PS-001
Wiring Cover Plate - Ford Sedan & Utility
7160-0444
This component is used to cover the gap that exists between the Gamber Johnson
Console Box/Top Plate and wiring tunnel when installed in a Ford NGPI Sedan or Utility vehicle
equipped with the optional wiring kit.
If installed, remove the arm rest assembly from the console box. Place Wiring Cover Plate over
gap with legs on Wiring Cover Plate outside the legs on wiring tunnel. Loosely install existing
vehicle bolts into slots on legs of Wiring Cover Plate attaching it to the wiring tunnel. Align slots
on vertical tab of Wiring Cover Plate with holes in console box. Using 1/4-20 bolts reattach arm
rest assembly to the console box clamping Wiring Cover Plate between console box and arm
rest assembly.
With everything in position tighten all fasteners.
If an arm rest assembly is not used attach the Wiring Cover Plate directly to the console box
using two (2) 1/4-20 X .625 Hex Head Bolts, lock washers and flat washers.
-
1
Gamber-Johnson 7160-0444 Specification
- Category
- Mounting kits
- Type
- Specification
Gamber-Johnson 7160-0444 is a Wiring Cover Plate designed for Ford Sedan & Utility vehicles equipped with the optional wiring kit. It covers the gap between the Gamber Johnson Console Box/Top Plate and wiring tunnel.
Key Features:
- Easy installation: Loosely install existing vehicle bolts into slots on legs of Wiring Cover Plate, align slots on vertical tab with holes in console box, and reattach arm rest assembly to clamp Wiring Cover Plate in place.
- Multiple mounting options: Can be attached directly to the console box using bolts, lock washers, and flat washers if an arm rest assembly is not used.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Gamber-Johnson Internal Armrest for 2011+ Dodge Charger and 2012+ Ford Police Interceptor Sedan/Utility Installation guide
-
-
-
-
Gamber-Johnson 2013-2019 Ford Police Interceptor Sedan Console, Cup Holder, Printer Armrest Installation guide
-
-
-
-
-
