Chevrolet Silverado User manual

2010 Chevrolet Silverado and GMC Sierra Two-mode Hybrid M
In Brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Hybrid Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Seats and Restraint System . . . . . . . . . . . . . . . . . . . . . . 2-1
Rear Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Restraint System Check . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Storage Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Starting and Operating Your Vehicle . . . . . . . . . . . . . 3-14
Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Climate Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Warning Lights, Gages, and Indicators . . . . . . . . . . . 4-3
Driver Information Center (DIC) . . . . . . . . . . . . . . . . . 4-11
Audio System(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13
Driving Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Your Driving, the Road, and the Vehicle . . . . . . . . . . 5-2
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Service and Appearance Care . . . . . . . . . . . . . . . . . . . 6-1
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Checking Things Under the Hood . . . . . . . . . . . . . . . . 6-3
Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23
Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25
Capacities and Specifications . . . . . . . . . . . . . . . . . . . 6-26
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
Maintenance Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i-1

GENERAL MOTORS, GM and the GM Emblem,

CHEVROLET, the CHEVROLET Emblem, GMC, the

GMC Emblem, and the names SILVERADO and

SIERRA are registered trademarks of General Motors.

This manual describes features that may or may not

be on your specific vehicle either because they are

options that you did not purchase or due to changes

subsequent to the printing of this owner manual. Please

refer to the purchase documentation relating to your

specific vehicle to confirm each of the features found

on your vehicle. For vehicles first sold in Canada,

substitute the name “General Motors of Canada

Limited” for Pontiac Motor Division wherever it

appears in this manual.

Keep this manual in the vehicle for quick reference.

Canadian Owners

Propriétaires Canadiens

A French language copy of this manual can be obtained

from your dealer/retailer or from:

On peut obtenir un exemplaire de ce guide en français

auprès du concessionnaire ou à l'adresse suivante:

Helm, Incorporated

P.O. Box 07130

Detroit, MI 48207

1-800-551-4123

Numéro de poste 6438 de langue française

www.helminc.com

ii

Litho in U.S.A.

Part No. 25855011 A First Printing

©

Introduction

Your hybrid pickup is designed to be more fuel efficient

than the standard pickup, which results in reduced

carbon dioxide emissions.

Using this Supplement

This supplement contains information specific to the

hybrid components of the vehicle. It does not explain

everything you need to know about the vehicle. Read

this supplement along with the owner manual to learn

about the vehicle's features and controls.

Index

A good place to look for what you need is the Index in

back of this supplement. It is an alphabetical list of what

is in the supplement, and the page number where you

will find it.

iii

2 NOTES

iv

Section 1 In Brief
Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Hybrid Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Hybrid Safety Information . . . . . . . . . . . . . . . . . . . . . . 1-2
Fuel Economy Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Automatic Engine Start/Stop Feature . . . . . . . . . . . . 1-3
Regenerative Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1-1

Initial Drive Information

Transmission

Range Selection Mode

The Range Selection Mode switch is located on the

shift lever. To enable the Range Selection feature, move

the column shift lever to the M (Manual) position. The

current range will appear next to the M. This is the

highest attainable range with all lower gears accessible.

As an example, when 3 (Third) gear is selected, 1 (First)

through 3 (Third) gears are available.

Press the plus/minus buttons, located on the

steering column shift lever, to select the desired range

of gears for current driving conditions. See Automatic

Transmission Operation in the owner manual.

Cruise control can be used while the vehicle is in Range

Selection Mode.

Hybrid Features

Hybrid Safety Information

This vehicle has a standard 12-volt battery and a

high-voltage hybrid battery. Only a trained service

technician with the proper knowledge and tools should

inspect, test, or replace the hybrid battery. See your

dealer/retailer if the hybrid battery needs service.

The 12-volt battery cables, in the engine compartment,

are clearly labeled. In emergency situations, first

responders can cut those cables to disable the

high-voltage hybrid battery system.

1-2

Fuel Economy Gage

United States Canada

This gage indicates fuel efficiency. To obtain the best

fuel efficiency, operate the vehicle so that the indicator

is in the high efficiency band.

Modifying both braking and acceleration behavior to

keep the indicator in the center of the gage will result

in the best system efficiency and fuel economy.

See Fuel Economy Gage on page 4‑5.

Automatic Engine Start/Stop Feature

Start the engine as you would any other engine. See

“Starting the Engine” in the owner manual for more

information on starting. The hybrid system provides

very quiet engine starting. If pulling a trailer with trailer

brakes, see Towing a Trailer

on page 5‑2

for more

information.

Auto Stop

The vehicle has an Auto Stop feature. After a

successful engine start, the engine may turn off

and operate in the Auto Stop mode.

Keep your foot firmly on the brake pedal until you are

ready for the vehicle to move.

Engine OFF and AUTO STOP modes are indicated on

the tachometer display. When the tachometer needle

indicates OFF, the engine is not running and will remain

off until the ignition key is placed in the START position

or a remote vehicle start is performed. When the

tachometer needle indicates AUTO STOP, the hybrid

system is on, the engine is not running, but may Auto

Start at any time without notice. See Tachometer

on

page 4‑4

for more information.

A chime will sound if the driver door is opened while in

Auto Stop as a reminder that the ignition switch is not in

the LOCK/OFF position. Always turn the ignition switch

to LOCK/OFF and remove the key from the ignition

switch when exiting the vehicle.

1-3

Auto Start

The vehicle also has an Auto Start feature. The engine

will remain off while in Auto Stop mode until vehicle

conditions require the engine to run. The near-instant

starting of the engine from Auto Stop mode is called

Auto Start.

EV Mode

The vehicle also has an EV mode which uses only

the electric motor to move the vehicle. With light

acceleration, the vehicle will drive in EV mode. EV

mode is unavailable when the vehicle is out of fuel.

See Starting the Vehicle in the Two‐Mode Hybrid

supplement to the owner manual.

Regenerative Braking

Regenerative braking enables the electric drive motor to

operate as a generator when coasting or braking.

Energy from the moving vehicle recharges the hybrid

battery.

The hydraulic disc brakes work with the regenerative

braking to insure effective braking.

The braking system is computer controlled and blends

the regenerative braking with the conventional hydraulic

disc brakes to meet any requirements for deceleration.

Because the controller applies the hydraulic brakes

through its high pressure accumulator, you may

occasionally hear the motor driven pump when it

recharges the system. This is normal. In the event of a

controller problem, the brake pedal may be harder to

push and the stopping distance may be longer.

See Regenerative Braking, Warning Lights, Gages, and

Indicators and Driver Information Center (DIC) in the

owner manual.

Battery

This vehicle has a standard 12-volt battery and a

high-voltage hybrid battery. When a new standard

12-volt battery is needed, see your dealer/retailer for

one that has the replacement number shown on the

original battery's label.

Only a trained service technician with the proper

knowledge and tools should inspect, test, or replace the

hybrid battery. See your dealer/retailer if the hybrid

battery needs service. See Battery on page 6‑17.

Service

Never try to do your own service on hybrid components.

You can be injured and the vehicle can be damaged if

you try to do your own service work. Service and repair

of these hybrid components should only be performed

by a trained service technician with the proper

knowledge and tools. See Doing Your Own Service

Work on page 6‑2.

1-4

Section 2 Seats and Restraint System

Rear Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Rear Seat Operation (Hybrid Full Bench) . . . . . . . 2-2

Restraint System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Replacing Restraint System Parts After

a Crash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

2-1

Rear Seats

Rear Seat Operation (Hybrid Full

Bench)

Folding Rear Seat

Notice: Folding a rear seat with the safety belts

still fastened may cause damage to the seat or the

safety belts. Always unbuckle the safety belts and

return them to their normal stowed position before

folding a rear seat.

Make sure that nothing is on the seat.

To fold the seat, slowly pull the seat cushion up.

To return the seat to the normal seating position, slowly

pull the seat cushion down.

{

WARNING:

A safety belt that is improperly routed, not

properly attached, or twisted will not provide the

protection needed in a crash. The person wearing

the belt could be seriously injured. After raising

the rear seatback, always check to be sure that

the safety belts are properly routed and attached,

and are not twisted.

Restraint System Check

Replacing Restraint System Parts

After a Crash

If an airbag inflates or the vehicle has been in a crash,

the vehicle's sensing system may command the

automatic hybrid battery disconnect to open. The

battery will disconnect. The hybrid battery will be off and

the vehicle will not start. The airbag readiness light and/

or SERVICE HYBRID SYSTEM warning message may

come on in the driver information center. See “Airbag

Readiness Light” in the owner manual and Driver

Information Center (DIC)

on page 4‑11

for more

information.

To operate the vehicle, the automatic hybrid battery

disconnect must be serviced by a qualified service

technician and sensing system parts will need to be

replaced. Have the vehicle serviced right away.

2-2

Section 3 Features and Controls
Storage Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Tonneau Cover (Hard Tonneau) . . . . . . . . . . . . . . . . . 3-2
Tonneau Cover (Soft Tonneau) . . . . . . . . . . . . . . . . . . 3-7
Starting and Operating Your Vehicle . . . . . . . . . . . . 3-14
Starting the Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Automatic Transmission Operation . . . . . . . . . . . . . 3-16
Engine Coolant Heater . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Regenerative Braking . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
Running the Vehicle While Parked . . . . . . . . . . . . . 3-21
3-1

Storage Areas

Tonneau Cover (Hard Tonneau)

Installing the Cover

{

CAUTION:

An improperly stored cargo cover could be thrown

about the vehicle during a collision or sudden

maneuver. Someone could be injured. If the cover

is removed, always store it in the proper storage

location. After positioning the cargo cover back on

the vehicle, always be sure that it is securely

reattached by properly securing the straps and

latches.

1. Position the tonneau cover onto the top of the

pickup box with the locator tabs positioned into

the front stake pockets.

2. Align the front edge of the cover with the front

edge of the bed rail so that it is centered on each

side of the truck bed.

3. Lower the front clamp from its storage position.

3-2

4. Tilt the clamp assembly so that the locator is in

the slot, pull down on the assembly, and slide

the clamp under the edge of the inner lip of the

bed rail.

5. Pull the handle toward the rear of the truck to

engage the clamp. Make sure the locator is secure

into the slot (A). If unable to completely engage

clamp, see the tightening and loosening

procedures later in this section.

6. The clamp should be securely engaged. Shake the

handle assembly to make sure the handle does

not move.

7. There are locking features on the front clamps

only. With the handle in the clamped position, push

the locking tab to engage the lock.

8. Repeat the clamp attachment steps 3 through 7 for

the opposite side.

Closing the Cover

1. Release both the retention straps located on the

top of the cover behind the cab and press into the

stored position.

2. Unfold the tonneau cover to the closed position.

3-3

3. Lower the rear set of clamp assemblies from the

stored position.

4. Tilt the clamp assembly so that the locator is in

the slot, pull down on the assembly, and slide

the clamp under the edge of the inner lip on the

bed rail.

5. Pull the handle toward the rear of the truck to

engage the clamp. Make sure the locator is

secured into the slot (A). If unable to completely

engage clamp, see the tightening and loosening

procedures later in this section.

6. The clamp should be securely engaged. Shake the

handle assembly to make sure the handle does

not move.

7. Repeat the clamp attachment steps 3 through 6 for

the opposite side.

8. Close the endgate.

Opening the Tonneau Cover

1. Turn both of the rear handles inward to release

compression.

2. Pull the clamp down and turn the assemblies to

disengage them from the lip of the pickup box.

3. Open the cover to expose the handles.

4. Align the clamp assembly bolt (A) with the

retention feature (B).

5. Turn the handle assembly and clamp assembly

bolt sideways (A) into the slot of the retention

feature (B).

3-4

6. The handle should lie flat on the panel with the

handles facing inward. Press firmly to secure.

This step must be done before stowing the cover.

7. Fold the cover forward.

8. Remove the retaining strap from the bow. Connect

the retention buckle ends. One end is located on

the front of the tonneau cover behind the cab and

the other end is on the tonneau cover

9. Pull on each strap to make sure both buckles are

attached.

Removing the Tonneau Cover

1. Open the cover by following the procedure

described previously, under “Opening the

Tonneau Cover”.

2. Disengage the locking tabs, located on the front

handles, by pulling them rearward.

3. Turn the handles inward to release.

4. Pull the clamp down and turn the assembly to

disengage it from the lip of the truck box.

5. Turn the cover to expose the handles.

3-5

6. Align the clamp assembly bolt (A), with the

retention feature (B).

7. Turn the handle assembly sideways by tilting the

assembly bolt (A) into the slot of the retention

feature (B).

8. The handle should lie flat on the panel with the

handles facing inward. Press firmly to secure.

9. Remove the tonneau cover from the vehicle.

Tightening the Clamp

1. Push the handle forward to release it from the

clamped position.

2. Disengage the clamp from the inner edge of the

bed rail and slide the assembly inward.

3. Adjust the clamp height on the bolt by turning the

entire clamp assembly counter-clockwise.

4. Attach the clamps as indicated in steps 4 and 5 of

Installing the Cover.

Loosening the Clamp

1. Return the handle to the fully disengaged position.

2. Disengage the clamp from the inner edge of the

bed rail and slide the assembly inward.

3. Adjust the clamp height by turning the entire clamp

assembly clockwise.

4. Reattach the clamps as indicated in steps 4 and 5

of Installing the Cover.

3-6

Tonneau Cover (Soft Tonneau)

Side Rail

{

WARNING:

An improperly stored cargo cover could be thrown

about the vehicle during a collision or sudden

maneuver. Someone could be injured. If the cover

is removed, always store it in the proper storage

location. After positioning the cargo cover back on

the vehicle, always be sure that it is securely

reattached by properly securing the straps and

latches.

Installation

1. The adjuster screw end

of each side rail should

point in the direction of

the cab.

2. Place each side rail on top of the truck box.

3. Align the front edge of the side rail with the front

inside edge of pickup box.

3-7

Clamp

Installation

1. Position three outer clamps (A), on each side rail.

The positions on the siderails are marked CLAMP.

2. Position the grooves of

the clamps on the side

rails (A) using the

center groove (B).

3. If the pickup box

has molded bed rail

protectors (A), remove

the insert (C) from the

outer groove on the

clamp, and position

the clamp on the side

rail (B) using the outer

groove (D).

4. Slide the inner

clamp (B) into the

outer clamp (A).

5. Turn the latch (C) onto

the outer clamp.

3-8

6. Tighten the clamp by turning the latch (C) toward

the side rail. Make sure there is no gap between

the rubber clamp pad and the side rail.

7. If the truck box has a molded bed rail protector,

insert the latch into the top notch on the inner

clamp.

8. Clean the vehicle's painted surface below the pull

strap using a 50/50 mixture of rubbing alcohol and

tap water.

9. Remove the paper from the provided clear tape

strip and apply to the painted surface below the

pull strap.

Adjustment

If there is excessive sideways movement of the

crossrails, move and re-install the clamps on the

loose areas using the inner groove of the clamp.

3-9

Cover

Installation

1. Place the cover assembly into the front pivot

mounts firmly against the adjustment screws.

2. Verify the gap between the adjuster screws and

pivot mounts is 3/16 in. Adjust if needed.

3-10

Page is loading ...

Chevrolet Silverado User manual

Chevrolet Silverado User manual

Related papers

Other documents