Page is loading ...
Tools/Outils/Herramientas
Before You Begin
Observe all local plumbing and building codes.
Shut off the water supply.
Install the required valves, K-438-K-NA or K-P438-K-NA, prior to installing the
product. Refer to the installation instructions packed with the valves.
A deep rough-in kit is available to accommodate an additional 1/2″ (1.3 cm) of tile
thickness for faucet installations using 1/2″ (73444) or 3/4″ (1086701) valve
systems.
Kohler Co. reserves the right to make revisions in the design of faucets without
notice, as specified in the Price Book.
Avant de commencer
Respecter tous les codes de plomberie et de bâtiment locaux.
Couper l’alimentation d’eau.
Installer les valves requises, K-438-K-NA ou K-P438-K-NA, avant d’installer le
produit. Se référer aux instructions d’installation emballées avec les valves.
Le kit de raccordement profond est disponible pour accommoder une épaisseur
supplémentaire de carrelage de 1/2″ (1,3 cm) pour des installations de robinet
utilisant des systèmes de valve de 1/2″ (73444) ou 3/4″ (1086701).
Kohler Co. se réserve le droit d’apporter toutes modifications au design des
robinets et ceci sans préavis, comme spécifié dans le catalogue des prix.
Antes de comenzar
Cumpla con todos los códigos locales de plomería y construcción.
Cierre el suministro de agua.
Antes de instalar el producto, instale las válvulas requeridas, K-438-K-NA o
K-P438-K-NA. Consulte las instrucciones de instalación que se incluyen con las
válvulas.
Un kit de instalación profunda está disponible para acomodar el espesor adicional
de azulejo de 1/2″ (1,3 cm) para instalaciones de grifería que utilizan los sistemas
de válvula de 1/2″ (73444) ó 3/4″ (1086701).
• Rags/Chiffons/Trapos
Plus/Plus/Más:
Hex Wrench
5/32" & 5/64"
Clé hexagonale
de 5/32" & 5/64"
Llave hexagonal
de 5/32" y 5/64"
Plumbers Putty
Mastic de plombier
Masilla de plomería
1161269-2-A 2 Kohler Co.
Antes de comenzar (cont.)
Kohler Co. se reserva el derecho de modificar el diseño de la grifería sin previo
aviso, tal como se especifica en la lista de precios.
1. Remove the Guard and Cap
Make sure the valves are closed (cold = fully counterclockwise; hot = fully
clockwise).
Turn off the main water supply.
Remove and discard the guard.
WARNING: Risk of personal injury. Do not lean over the pipe plug when
turning or removing the pipe plug. The water supply lines may be pressurized,
causing water to spray or purge when removing the pipe plug.
NOTICE: Water may spray from the diverter body when you remove the cap.
Wrap a rag around the cap to prevent water spray.
Carefully remove and discard the cap.
Retirer le renfort et le couvercle
S’assurer que les robinets soient fermés (côté froid complètement vers la gauche,
côté chaud complètement vers la droite).
Fermer l’alimentation d’eau principale.
Retirer et jeter le renfort.
AVERTISSEMENT: Risque de blessures corporelles. Ne pas se pencher sur le
bouchon du tuyau au moment de le tourner ou lors de son retrait. Les
canalisations d’alimentation d’eau peuvent être sous pression, ce qui cause des jets
ou des purges d’eau lors du retrait du bouchon du tuyau.
NOTICE: L’eau pourrait gicler du corps de l’inverseur lorsque le bouchon est retiré.
Enrouler un torchon autour du bouchon pour empêcher l’eau de gicler.
Cap
Capuchon
Tapa
Guard
Dispositif de protection
Protector
Diverter Body
Corps inverseur
Cuerpo del desviador
Close Hot
Fermer l'eau chaude
Cierre del agua caliente
Close Cold
Fermer l'eau froide
Cierre del agua fría
Kohler Co. 3 1161269-2-A
Page is loading ...
Install Spout (cont.)
NOTICE: To avoid damage to the O-rings while assembling the spout, ensure the
diverter body and tube are clean.
Thread the lift rod into the stem three turns.
Lift upward on the lift rod assembly, hold the stem with a needlenose pliers (to
keep it from spinning), and thread the lift rod assembly into the stem all the way.
Release the stem.
Slide the tube onto the lift rod assembly.
Push the tube down until it contacts the bottom of the diverter.
Loosen the setscrew on the spout assembly until it is clear of the inside wall of the
spout.
NOTE: Do not bend the lift rod assembly or tube during spout installation. If the lift
rod assembly or tube are bent they may not function correctly.
Position the spout over the lift rod assembly and diverter tube, then carefully
press down until the spout contacts the finished deck. If there is resistance do not
force the spout down. Further loosen the setscrew and repeat.
Rotate the spout until it is aligned to face straight forward.
Tighten the setscrew.
Press the plug button into place until flush with the surface of the spout.
Installer le bec
NOTICE: Afin d’éviter d’endommager les joints toriques pendant l’assemblage du
bec, s’assurer que le corps et le tube de l’inverseur sont propres.
Enfiler la tige de levage dans la tige de trois tours.
Lever la tige de levage vers le haut, maintenir la tige avec des pinces fines à bec
en aiguille (pour empêcher de tourner), et enfiler entièrement la tige de levage
dans la tige.
Dégager la tige.
Faire glisser le tube sur la tige de levage.
Pousser le tube vers le bas, jusqu’à ce qu’il entre en contact avec le bas de
l’inverseur.
Desserrer la vis de retenue du bec jusqu’à ce qu’elle soit dégagée de la paroi
intérieure du bec.
REMARQUE: Ne pas plier la tige de levage ou le tube pendant l’installation du bec.
Si la tige de levage ou le tube sont pliés, ils risquent de ne pas fonctionner
correctement.
Positionner le bec par-dessus le tube de levage et le tube de l’inverseur, puis
appuyer avec précaution vers le bas jusqu’à ce que le bec touche le comptoir fini.
En cas de résistance, ne pas forcer le bec vers le bas. Continuer à desserrer la vis
de retenue et répéter.
Pivoter le bec jusqu’à ce qu’il soit aligné de face.
Serrer la vis de retenue.
Appuyer sur le bouchon capsule pour le mettre en place, jusqu’à ce qu’il soit à ras
du bec.
Kohler Co. 5 1161269-2-A
Page is loading ...
3. Install the Diverter Knob
Make sure the neck of the adjustable screw is aligned with the setscrew hole. If
they are not aligned remove the knob and raise or lower the adjustable screw to
align.
While pressing downward on the knob, install and tighten the setscrew.
NOTE: If after installation water leaks out of the handshower during use, adjustment
is required. To make the adjustments remove the knob, raise the adjustable screw
slightly higher, and reattach the knob.
Installer la poignée de l’inverseur
S’assurer que le cou de la vis réglable est alignée avec l’orifice de la vis de
retenue. Si elles ne sont pas alignées, retirer le bouton et élever ou abaisser la vis
réglable pour effectuer l’alignement.
Tout en appuyant vers le bas sur le bouton, installer et serrer la vis de retenue.
REMARQUE: Si, après l’installation, de l’eau fuit hors de la douchette pendant
l’utilisation, un réglage est requis. Pour effectuer les réglages, retirer le bouton, élever
légèrement la vis réglage plus haut, et réattacher le bouton.
Setscrew
Vis de retenue
Tornillo de fijación
Lift Rod
Tige de levage
Tirador
Knob
Poignée
Perilla
Spout
Bec
Surtidor
Adjustable Screw
Vis à molette
Tornillo adjustable
Neck
Cou
Cuello
Setscrew
Vis de retenue
Tornillo de fijación
Lift Rod Assembly
Ensemble de tige
de levage
Montaje del tirador
Knob
Poignée
Perilla
Kohler Co. 7 1161269-2-A
Instale la perilla del desviador
Asegúrese de que el cuello del tornillo ajustable esté alineado con el orificio para
el tornillo de fijación. Si no están alineados retire la perilla y suba o baje el tornillo
ajustable para alinear.
Mientras presiona hacia abajo la perilla, instale y apriete el tornillo de fijación.
NOTA: Si después de la instalación se fuga agua de la ducha de mano durante el
uso, será necesario ajustar. Para ajustar, retire la perilla, suba ligeramente el tornillo
ajustable y vuelva a instalar la perilla.
4. Install Handles
Remove the plaster guards.
Measure the distance from the top of the valve stem to the finished surface.
For a valve stem height between 1-13/16″ (4.6 cm) and 2-1/8″ (5.4 cm) use a brass
spline adapter and screw. For a valve stem height between 2-1/8″ (5.4 cm) and
2-5/16″ (5.9 cm) use a plastic spline adapter.
If the brass spline adapter is required, attach using the screw supplied. The plastic
spline adapter slides on with no attachment.
Position the handle assemblies facing in opposite directions away from the spout.
NOTE: The spline adapter allows fine adjustment of the handle alignment. To adjust,
remove the handle and reposition the spline adapter.
Align the handle.
Reinstall the handle and check alignment.
Handle/Poignée/Manija
Screw/Vis/Tornillo
Apply plumbers putty.
Appliquer du mastic de plombier.
Aplique masilla de plomería.
Brass Spline Adapter
Adaptateur à cannelures en laiton
Adaptador de ranuras de latón
Plastic Spline Adapter
Adaptateur à cannelures en plastique
Adaptador de ranuras de plástico
Valve Stem
Tige de valve
Espiga de la válvula
Height Measurement
Hauteur
Medida de la altura
Finished Surface
Surface finie
Superficie acabada
Cold
Froid
Fría
Hot
Chaud
Caliente
Handle Orientation
Orientation de la poignée
Orientación de la manija
1161269-2-A 8 Kohler Co.
Installer les poignées
Retirer les renforts en plâtre.
Mesurer la distance depuis le dessus de la tige de la valve à la surface finie.
Utiliser l’adaptateur à cannelures en laiton et la vis pour une hauteur de tige de
valve comprise entre 1-13/16″ (4,6 cm) et 2-1/8″ (5,4 cm). Utiliser l’adaptateur à
cannelures en plastique pour une hauteur de tige de valve comprise entre 2-1/8″
(5,4 cm)]et 2-5/16″ (5,9 cm).
Lorsqu’il est nécessaire d’utiliser un adaptateur à cannelures, raccorder avec la vis
fournie. L’adaptateur à cannelures plastique ne nécessite pas de raccord.
Positionner les ensembles de poignées de façon à ce qu’elles soient en directions
opposées, loin du bec.
REMARQUE: L’adaptateur à cannelures permet un alignement de la poignée précis.
Pour ajuster, retirer la poignée et repositionner l’adaptateur à cannelures.
Aligner la poignée.
Réinstaller la poignée et vérifier l’alignement.
Instale las manijas
Retire los protectores de yeso.
Mida la distancia desde la parte superior de la espiga de válvula hasta la
superficie acabada.
Utilice un adaptador de ranuras de latón y un tornillo, en caso de que la altura de
la espiga de la válvula sea entre 1-13/16″ (4,6 cm) y 2-1/8″ (5,4 cm). Utilice el
adaptador de ranuras de plástico en caso de que la altura de la espiga de la
válvula sea entre 2-1/8″ (5,4 cm) y 2-5/16″ (5,9 cm).
Si es necesario utilizar el adaptador de ranuras de latón, fíjelo con el tornillo
provisto. El adaptador de ranuras de plástico se ajusta sin necesidad de tornillos.
Coloque los montajes de las manijas orientados en dirección opuesta al surtidor.
NOTA: El adaptador de ranuras permite el ajuste fino de alineación de la manija.
Para ajustarla, retire la manija y cambie la posición del adaptador de ranuras.
Alinee la manija.
Vuelva a instalar la manija y verifique la alineación.
5. Complete the Installation
Ensure that both handles are turned off (hot = clockwise, cold = counterclockwise).
Make sure that all connections are tight.
Turn on the main water supply and check for leaks.
Turn on the hot and cold valves and run water through the spout to remove
debris. Check for leaks.
Confirm proper diverter operation.
Disengage the diverter. Check the handshower to confirm no water flows from it
when the diverter is not engaged. Water should flow from the spout only.
If water flows from the handshower while the diverter is not engaged, the
adjustable screw needs to be raised slightly. To make the adjustments remove the
knob, raise the adjustable screw slightly higher, and reattach the knob following
the directions in the ″Install the Diverter Knob″ section.
Turn the handles to the off position and then back to the on position. Verify that
the water flow is diverted back to the spout.
Kohler Co. 9 1161269-2-A
Page is loading ...
Care and Cleaning (cont.)
•
Always test your cleaning solution on an inconspicuous area before applying to
the entire surface.
•
Do not allow cleaners to sit or soak on the surface.
•
Wipe surfaces clean and rinse completely with water immediately after cleaner
application. Rinse and dry any overspray that lands on nearby surfaces.
•
Use a soft, dampened sponge or cloth. Never use an abrasive material such as a
brush or scouring pad to clean surfaces.
For detailed cleaning information and products to consider, visit www.kohler.com/clean.
To order Care & Cleaning information, call 1-800-456-4537.
Entretien et nettoyage
Pour obtenir les meilleurs résultats possibles, prendre ce qui suit en considération lors de
l’entretien de votre produit KOHLER:
•
Utiliser un détergent doux tel que liquide pour vaisselle et de l’eau chaude pour
nettoyer. Ne pas utiliser de nettoyants abrasifs car ils pourraient rayer ou abîmer
la surface.
•
Lire attentivement l’étiquette du produit de nettoyage pour vérifier qu’il soit
adéquat à utiliser sur le matériau.
•
Toujours tester la solution de nettoyage sur une surface non visible avant de
l’appliquer sur l’ensemble de la surface.
•
Ne pas permettre aux nettoyants de reposer sur la surface.
•
Essuyer les surfaces et rincer complètement avec de l’eau immédiatement après
l’application du nettoyant. Rincer et sécher tout éclaboussement sur les surfaces
avoisinantes.
•
Utiliser une éponge ou un chiffon doux et humide. Ne jamais utiliser de matériau
abrasif tel qu’une brosse ou une éponge à récurer pour nettoyer les surfaces.
Pour obtenir des informations détaillées sur le nettoyage et les produits à considérer,
consulter le site www.kohler.com/clean. Pour commander des informations sur
l’entretien & le nettoyage, appeler le 1-800-456-4537.
Cuidado y limpieza
Para obtener los mejores resultados, tenga presente lo siguiente al limpiar su producto
KOHLER:
•
Para la limpieza, utilice solamente un detergente suave como el jabón líquido para
lavar platos y agua tibia. No utilice limpiadores abrasivos que puedan rayar u
opacar la superficie.
•
Lea atentamente la etiqueta del producto de limpieza para asegurar que no
presente riesgos al usarse en el material.
•
Siempre pruebe la solución de limpieza en un área oculta antes de aplicarla a toda
la superficie.
•
No deje por tiempo prolongado los limpiadores en la superficie.
•
Limpie con un trapo y enjuague completa e inmediatamente con agua después de
aplicar limpiadores. Enjuague y seque las superficies cercanas que se hayan
rociado.
•
Utilice una esponja o trapo suave y húmedo. Para limpiar las superficies nunca
utilice materiales abrasivos como cepillos o estropajos de tallar.
Para obtener información detallada de limpieza y los limpiadores a considerar, visite
www.kohler.com/clean. Para solicitar información sobre el cuidado y la limpieza, llame
al 1-800-456-4537.
Kohler Co. 11 1161269-2-A
Warranty
KOHLER
®
Faucet Lifetime Limited Warranty
Kohler Co. warrants its Faucets* manufactured after January 1, 1997, to be leak and drip
free during normal residential use for as long as the original consumer purchaser owns
his or her home. If the Faucet should leak or drip during normal use, Kohler Co. will,
free of charge, mail to the purchaser the cartridge necessary to put the Faucet in good
working condition. This warranty applies only to Kohler Faucets installed in the United
States of America, Canada or Mexico (″North America″).
Kohler Co. also warrants all other aspects of the faucet or accessories (″Faucet″)*, (except
gold, non-Vibrant
®
, non-chrome finishes) to be free of defects in material and
workmanship during normal residential use for as long as the original consumer
purchaser owns his or her home. This warranty applies only to Kohler Faucets installed
in North America. If a defect is found in normal residential use, Kohler Co. will, at its
election, repair, provide a replacement part or product, or make appropriate adjustment.
Damage to a product caused by accident, misuse, or abuse is not covered by this
warranty. Improper care and cleaning will void the warranty**. Proof of purchase
(original sales receipt) must be provided to Kohler Co. with all warranty claims. Kohler
Co. is not responsible for labor charges, installation, or other incidental or consequential
costs. In no event shall the liability of Kohler Co. exceed the purchase price of the
Faucet.
If the Faucet is used commercially or is installed outside of North America, or if the
finish is gold, non-Vibrant or a painted or powder coated color finish, Kohler Co.
warrants the Faucet to be free from defects in material and workmanship for one (1) year
from the date the product is installed, under Kohler Co.’s standard one-year limited
warranty.
If you believe that you have a warranty claim, contact Kohler Co., either through your
Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing Kohler Co., Attn.:
Customer Care Center, 444 Highland Drive, Kohler, WI 53044, USA. Please be sure to
provide all pertinent information regarding your claim, including a complete description
of the problem, the product, model number, color, finish, the date the product was
purchased and from whom the product was purchased. Also include your original
invoice. For other information, or to obtain the name and address of the service and
repair facility nearest you, call 1-800-4-KOHLER (1-800-456-4537) from within the USA
and Canada, and 001-800-456-4537 from within Mexico, or visit www.kohler.com within
the USA, www.ca.kohler.com from within Canada, or www.mx.kohler.com in Mexico.
KOHLER CO. AND/OR SELLER ARE PROVIDING THESE WARRANTIES IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. KOHLER CO. AND/OR SELLER
DISCLAIM ALL LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. Some states/provinces do not allow limitations of how long an implied
warranty lasts or the exclusion or limitation of such damages, so these limitations and
exclusions may not apply to you. This warranty gives the consumer specific legal
rights. You may also have other rights that vary from state/province to state/province.
This is Kohler Co.’s exclusive written warranty.
*Trend
®
faucets, MasterShowerTM tower, BodySpaTM systems and components;
WaterHaven
TM tower, systems and components; TripointTM faucets, Polished Gold,
non-Vibrant and painted or powder coated finishes, fittings; all items within the ″Fixture
Related″ section of the Kohler Faucets Price Book, drains, Duostrainer
®
sink strainers,
soap/lotion dispensers; and faucets used in commercial settings, and outside North
America, are covered by Kohler Co.’s one-year limited warranty.
**Never use cleaners containing abrasive cleansers, ammonia, bleach, acids, waxes,
alcohol, solvents or other products not recommended for chrome. This will void the
warranty.
1161269-2-A 12 Kohler Co.
Page is loading ...
Page is loading ...
Garantía (cont.)
*La grifería Trend
®
; la torre MasterShowerTM; los sistemas y componentes BodySpaTM;la
torre, sistemas y componentes WaterHavenTM; las griferías TripointTM, el acabado en oro
pulido, que no sea Vibrant y los acabados con revestimiento de pintura o en polvo;
conexiones; todos los artículos contenidos en la sección ″Fixture Related″ del KOHLER
Faucets Price Book, los desagües, las coladeras de fregadero Duostrainer
®
,los
dispensadores de jabón y loción; y la grifería de uso comercial e instalada fuera del
territorio de Norteamérica, están cubiertos por la garantía limitada de un año de Kohler
Co.
**Nunca utilice limpiadores que contengan limpiadores abrasivos, amoníaco, cloro
(blanqueador), ácidos, ceras, alcohol, disolventes u otros productos no recomendados
para el cromo. Esto anulará la garantía.
Warranty
For Mexico
KOHLER CO.
It is recommended that at the time of purchase, you verify that all accessories and
components are complete in this package.
This Kohler product is warranted to be free of defects in material and workmanship for
one (1) year from the date of purchase as shown on the invoice or receipt.
1. Kohler Co. will only service its commercialized products through its authorized
distributors.
2. To obtain warranty service, please present the invoice and corresponding warranty.
3. Through its authorized distributors, Kohler Co. promises to repair the defective
product or provide a new replacement or an equivalent model (in those cases that the
model has been discontinued) when the product is beyond repair, without any charge to
the consumer.
4. The time of repair will not exceed six (6) weeks commencing on the date the product
is received.
5. It is recommended that the consumer save the invoice or receipt as additional
protection, as it may substitute the warranty in the case that there is a discrepancy in the
validity of the warranty.
EXCEPTIONS AND RESTRICTIONS
The Warranty will not be valid in the following cases:
1. When the product is not operated in accordance with the instructions concerning use
and operation set forth in the owner’s manual or installation instructions, and when the
recommendations and warnings included are not observed.
2. When the product has been modified or dismantled partially or totally; or has been
used in a negligent fashion and as a consequence has suffered damages attributable to
the consumer, individual, or hardware not authorized by Kohler Co.
3. This warranty does not cover the damages as a result of disaster such as fire or acts of
God, including flooding, earthquake, or electric storms, etc. To obtain a list of
distributors in your area where you can exercise your rights under this warranty, please
call 001-800-456-4537.
KOHLER CO., KOHLER, WI 53044 U.S.A.
Kohler Co. 15 1161269-2-A
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Kohler K-T5324-4-BN Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Kohler K-T5324-4-BN Guide d'installation
- español: Kohler K-T5324-4-BN Guía de instalación
Related papers
-
Kohler K-7509 Installation guide
-
-
-
-
-
-
-
-
-
