H3C S3610 Series Quick start guide

H3C S3610 Series Ethernet Switches

Quick Start

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08225A-20080526-C-1.07

Ltd. and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF,

NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,

Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus,

N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners.

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

To obtain the latest information, please access:

http://www.h3c.com

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S3610 Series Ethernet

Switches documentation set includes the following:

Manual Content

H3C S3610&S5510 Series

Ethernet Switches Operation

Manual

It is used for assisting the users

in data configurations and

typical applications

H3C S3610&S5510 Series

Ethernet Switches Command

Manual

It is used for assisting the users

in using various commands.

H3C S3610 Series Ethernet

Switches Installation Manual

It is used for assisting the users

in switch installation, booting up,

hardware and software

maintenance.

Organization

H3C S3610 Series Ethernet Switches Quick Start is organized as

follows:

Chapter Contents

1 Product Overview

Introduces the characteristics and technical

specifications of S3610 Series Ethernet

Switches.

Chapter Contents

2 Installation

Preparation

Introduces the installation preparation and

precaution of S3610 Series Ethernet

Switches.

3 Installing the

Switch

Introduces the procedures to install an

S3610 Series Ethernet Switch, including the

setup of the mainframe, cards and cables.

4 Lightning

Protection of the

Switch

Introduces lightning protection of S3610

Series Ethernet Switches.

Conventions

The manual uses the following conventions:

I.

Command conventions

Convention Description

Boldface

The keywords of a command line are in

Boldface.

italic

Command arguments are in italic.

[ ]

Items (keywords or arguments) in square

brackets [ ] are optional.

{ x | y | ... }

Alternative items are grouped in braces

and separated by vertical bars. One is

selected.

[ x | y | ... ]

Optional alternative items are grouped in

square brackets and separated by vertical

bars. One or none is selected.

{ x | y | ... } *

Alternative items are grouped in braces

and separated by vertical bars. A minimum

of one or a maximum of all can be selected.

Convention Description

[ x | y | ... ] *

Optional alternative items are grouped in

square brackets and separated by vertical

bars. Many or none can be selected.

&<1-n>

The argument(s) before the ampersand (&)

sign can be entered 1 to n times.

# A line starting with the # sign is comments.

II.

GUI conventions

Convention Description

< >

Button names are inside angle brackets.

For example, click <OK>.

[ ]

Window names, menu items, data table

and field names are inside square

brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward

slashes. For example, [File/Create/Folder].

III.

Symbols

Convention Description

Warning

Means reader be extremely careful.

Improper operation may cause bodily

injury.

Caution

Means reader be careful. Improper

operation may cause data loss or damage

to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements

on environmental protection. For the proper storage, use and disposal

of this product, national laws and regulations must be observed.

Quick Start

H3C S3610 Series Ethernet Switches

Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................1-1

1.1 Introduction ........................................................................1-1

1.2 S3610-28TP Ethernet Switch.............................................1-3

1.2.1 Front Panel..............................................................1-3

1.2.2 Rear Panel...............................................................1-4

1.2.3 Power Supply System.............................................1-4

1.2.4 Cooling System .......................................................1-5

1.3 S3610-28P Ethernet Switch...............................................1-5

1.3.1 Front Panel..............................................................1-5

1.3.2 Rear Panel...............................................................1-6

1.3.3 Power Supply System.............................................1-6

1.3.4 Cooling System .......................................................1-6

1.4 S3610-28F Ethernet Switch...............................................1-7

1.4.1 Front Panel..............................................................1-7

1.4.2 Rear Panel...............................................................1-7

1.4.3 Power Supply System.............................................1-8

1.4.4 Cooling System .......................................................1-8

1.5 S3610-52P Ethernet Switch...............................................1-8

1.5.1 Front Panel..............................................................1-8

1.5.2 Rear Panel...............................................................1-9

1.5.3 Power Supply System...........................................1-10

1.5.4 Cooling System .....................................................1-10

1.6 S3610-52M/S3610-52M-DC Ethernet Switch..................1-10

1.6.1 Front Panel............................................................1-10

1.6.2 Rear Panel.............................................................1-11

Quick Start

H3C S3610 Series Ethernet Switches

Table of Contents

ii

1.6.3 Power Supply System...........................................1-13

1.6.4 Cooling System .....................................................1-13

1.7 LEDs ................................................................................1-14

1.7.1 LEDs of the S3610-28TP Ethernet switch.............1-14

1.7.2 LEDs of the S3610-28P Ethernet switch...............1-21

1.7.3 LEDs of the S3610-28F Ethernet switch...............1-26

1.7.4 LEDs of the S3610-52P Ethernet switch...............1-34

1.7.5 LEDs of the S3610-52M/S3610-52M-DC Ethernet

switch..............................................................................

1-34

1.8 Specifications of the S3610 Series..................................1-36

1.9 SFP modules....................................................................1-38

1.9.1 100 Mbps SFP modules........................................1-38

1.9.2 1000 Mbps SFP modules......................................1-38

Chapter 2 Installation Preparation...............................................2-1

2.1 Safety Precautions.............................................................2-1

2.2 Installation Site...................................................................2-1

2.2.1 Temperature/Humidity.............................................2-2

2.2.2 Cleanness................................................................2-2

2.2.3 Electromagnetic Susceptibility.................................2-3

2.2.4 Laser Safety ............................................................2-4

2.3 Installation Tools................................................................2-4

Chapter 3 Installing the Switch....................................................3-1

3.1 Installing a Switch ..............................................................3-1

3.1.1 Cabinet Mounting....................................................3-1

3.1.2 Desk Mounting.........................................................3-8

3.2 Connecting the Power Cord and the Ground Wire............3-8

3.2.1 Connecting the AC Power Cord..............................3-8

3.2.2 Connecting the DC-Input Power Cord...................3-10

Quick Start

H3C S3610 Series Ethernet Switches

Table of Contents

iii

3.2.3 Connecting the Ground Wire.................................3-15

3.2.4 Multi-power Input...................................................3-19

3.3 Connecting the Switch to a Console Terminal.................3-20

3.3.1 Console Cable.......................................................3-20

3.3.2 Connecting the Console Cable..............................3-21

3.4 Installation of the Optional Interface Modules..................3-22

3.4.1 Installation of the Optional Interface Modules.......3-22

3.4.2 Removal of Optional Interface Modules................3-23

3.5 Verifying Installation.........................................................3-24

Chapter 4 Lightning Protection of the Switch ............................4-1

4.1 Installation of Lightning Arrester for AC Power (Socket Strip

with Lightning Protection).........................................................

4-1

4.2 Installation of Lightning Arrester for Network Port.............4-4

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Introduction

H3C S3610 Series Ethernet Switches (the S3610 series) are

L2/L3 wire speed Ethernet switches developed by Hangzhou H3C

Technologies Co., Ltd. They are intelligent network management

switches intended for networks where high performance, dense port

distribution, and ease of installation are required.

The S3610 series are designed to operate on the convergence

and access layer of intranets and metropolitan area networks (MANs).

They support both IPv4 and IPv6 and thus offer abundant services

and routing functionalities.

Currently, S3610 series contain the following models.

Table 1-1 Models in the S3610 series

Model

Power

supply

Total

service

ports

Number

of 100

Mbps

ports

Number

of 1000

Mbps

uplink

ports

Console

port

S3610

-28TP

AC-input

DC-input

28

24 fixed

10Base-

T/100Ba

se-TX

Ethernet

ports

2 × 1000

Mbps SFP

ports

2 ×

10/100/10

00MBase-

T Ethernet

ports

One

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-2

Model

Power

supply

Total

service

ports

Number

of 100

Mbps

ports

Number

of 1000

Mbps

uplink

ports

Console

port

S3610

-28P

AC-input

DC-input

28

24 fixed

10Base-

T/100Ba

se-TX

Ethernet

ports

4 × 1000

Mbps SFP

ports

One

S3610

-28F

AC-input

DC-input

28

24 x 100

Mbps

SFP

ports

2 × 1000

Mbps SFP

ports

2 ×

10/100/10

00MBase-

T Ethernet

ports

One

S3610

-52P

AC-input

DC-input

52

48 fixed

10Base-

T/100Ba

se-TX

Ethernet

ports

4 × 1000

Mbps SFP

ports

One

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-3

Model

Power

supply

Total

service

ports

Number

of 100

Mbps

ports

Number

of 1000

Mbps

uplink

ports

Console

port

S3610

-52M

AC-input One

S3610

-52M-

DC

DC-input

Dependi

ng on

the

inserted

interfac

e

module,

52 at

most.

Dependi

ng on the

inserted

interface

module,

up to 48

10/100

Mbps

electrical

ports or

48 100

Mbps

SFP

ports

4 × 1000

Mbps SFP

ports

4 ×

10/100/10

00 Mbps

electrical

ports

One

1.2 S3610-28TP Ethernet Switch

1.2.1 Front Panel

On its front panel the S3610-28TP provides 24 fixed

10Base-T/100Base-TX Ethernet ports, two 1000 Mbps SFP ports, two

10/100/1000Base-T Ethernet ports and one Console port, as shown in

Figure 1-1.

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-4

(1): 100 Mbps Ethernet port status LEDs

(2): 1000 Mbps SFP port status LEDs

(3): 1000 Mbps Ethernet port status LEDs

(4): Console port (5): 7-segment numerical display

(6): Port mode switch button (7): Port mode switch LED

(8): Power LED (9): DC-input power LED

Figure 1-1 Front panel of an S3610-28TP Ethernet switch

1.2.2 Rear Panel

（1）（2）（3）（1）（2）（3）

(1): AC-input power socket

(2): DC-input power socket

(3): Grounding screw

Figure 1-2 Rear panel of an S3610-28TP Ethernet switch

1.2.3 Power Supply System

The S3610-28TP supports power load sharing between the AC

and DC power supply. It can also be powered by the AC power supply

or DC power supply only.

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-5

I. AC input:

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz

II. DC input:

Rated voltage range: -48 V to -60 V

Max voltage range: -36 V to -72V

1.2.4 Cooling System

S3610-28TP Ethernet switch provide one fan for heat dissipation.

1.3 S3610-28P Ethernet Switch

1.3.1 Front Panel

On its front panel the S3610-28P provides 24 fixed

auto-negotiation 10Base-T/100Base-TX Ethernet ports, four 1000

Mbps SFP ports and one Console port, as shown in

Figure 1-3.

(1): 100 Mbps Ethernet port status LEDs

(2): 1000 Mbps SFP port status LEDs (3): Console port

(4): 7-segment numerical display (5): Port mode switch button

(6): Port mode switch LED (7): Power LED

(8): DC-input power LED

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-6

Figure 1-3 Front panel of the S3610-28P

1.3.2 Rear Panel

（1）（2）（3）（1）（2）（3）

(1): AC-input power socket

(2): DC-input power socket

(3): Grounding screw

Figure 1-4 Rear panel of the S3610-28P

1.3.3 Power Supply System

The S3610-28P supports power load sharing between the AC

and DC power supply. It can also be powered by the AC power supply

or DC power supply only.

I. AC input:

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz

II. DC input:

Rated voltage range: -48 V to -60 V

Max voltage range: -36 V to -72V

1.3.4 Cooling System

S3610-28P Ethernet switch provide one fan for heat dissipation.

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-7

1.4 S3610-28F Ethernet Switch

1.4.1 Front Panel

On its front panel the S3610-28F provides 24 x 100 Mbps SFP

ports, two 1000 Mbps SFP ports, two 10/100/1000Base-T Ethernet

ports and one Console port, as shown in

Figure 1-5.

(1): 100 Mbps SFP port status LEDs

(2): 1000 Mbps SFP port status LEDs

(3): 1000 Mbps Ethernet port status LEDs

(4): Console port (5): 7-segment numerical display

(6): Port mode switch button (7): Port mode switch LED

(8): Power LED (9): DC-input power LED

Figure 1-5 Front panel of the S3610-28F

1.4.2 Rear Panel

(1)

(2)

(3)

(1)

(2)

(3)

(1): AC-input power socket (2): DC-input power socket

(3): Grounding screw

Figure 1-6 Rear panel of the S3610-28F Ethernet switch

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-8

1.4.3 Power Supply System

The S3610-28F supports power load sharing between the AC

and DC power supply. It can also be powered by the AC power supply

or DC power supply only.

I. AC input:

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz

II. DC input:

Rated voltage range: -48 V to -60 V

Max voltage range: -36 V to -72V

1.4.4 Cooling System

S3610-28F Ethernet switch provide two fans for heat dissipation.

1.5 S3610-52P Ethernet Switch

1.5.1 Front Panel

On its front panel the S3610-52P provides 48 fixed

auto-negotiation 10Base-T/100Base-TX Ethernet ports, four 1000

Mbps SFP ports and one Console port, as shown in

Figure 1-7.

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-9

(1): 100 Mbps Ethernet port status LEDs (2): Console port

(3): 7-segment numerical display (4): Port mode switch button

(5): Port mode switch LED (6): Power LED

(7): DC-input power LED

(8): 1000 Mbps SFP port status LEDs

Figure 1-7 Front panel of the S3610-52P

1.5.2 Rear Panel

（1）（2）（3）（1）（2）（3）

(1): AC-input power socket

(2): DC-input power socket

(3): Grounding screw

Figure 1-8 Rear panel of the S3610-52P Ethernet switch

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-10

1.5.3 Power Supply System

The S3610-52P supports power load sharing between the AC

and DC power supply. It can also be powered by the AC power supply

or DC power supply only.

I. AC input:

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz

Max voltage range: 90 VAC to 264 VAC, 50 Hz or 60 Hz

II. DC input:

Rated voltage range: -48 V to -60 V

Max voltage range: -36 V to -72V

1.5.4 Cooling System

S3610-52P Ethernet switch provide one fan for heat dissipation.

1.6 S3610-52M/S3610-52M-DC Ethernet

Switch

1.6.1 Front Panel

On its front panel, the S3610-52M/S3610-52M-DC switch

provides six slots where you can insert the 8-port 100 Mbps

single-mode/multimode modules, 8-port 10Base-T/100Base-TX

modules, and 8-port 100 Mbps SFP modules as needed. The

following figure illustrates the front panel with all the six slots inserted

with 8-port 100 Mbps single-mode modules:

Quick Start

H3C S3610 Series Ethernet Switches

Chapter 1 Product Overview

1-11

(1) (2)

(1): Power LED (2): Console port

Figure 1-9 Front panel of the S3610-52M/S3610-52M-DC

Caution:

The interface modules on the front panel of the H3C S3610-52M and

S3610-52M-DC are not hot-swappable. To install or remove these

modules, you must first power off the switch. For how to install and

remove these modules, refer to section

3.4 “Installation of the

Optional Interface Modules”.

1.6.2 Rear Panel

I. Rear panel of the S3610-52M switch

The rear panel of the S3610-52M switch is illustrated by the

following figure. On the rear panel, there are grounding screw,

AC-input power socket, RPS DC-input redundancy power socket, and

the fixed interface module.

Page is loading ...

H3C S3610 Series Quick start guide

H3C S3610 Series Quick start guide

Related papers

Other documents