Samsung LE23R51BX Owner's manual

LCD TV

LE23R51B

LE23R41B

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

-

AFTER SALES SERVICE

-

Do not hesitate to contact your retailer or service agent if a

change in the performance of your product indicates that a

faulty condition may be present.

BN68-00882C-01

ON-SCREEN MENUS

PC DISPLAY

PICTURE IN PICTURE (PIP)

TELETEXT

This device is a Class B digital apparatus.

Register your product at

www.samsung.com/global/register

LCD TV LE23R51B/LE23R41B

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European

countries with separate collection systems)

This marking shown on the product or its literature,

indicates that it should not be disposed with other

household wastes at the end of its working life. To prevent possible

harm to the environment or human health from uncontrolled waste

disposal, please separate this from other types of wastes and recycle

it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they

purchased this product, or their local government office, for details of

where and how they can take this item for environmentally safe

recycling.

Business users should contact their supplier and check the terms and

conditions of the purchase contract. This product should not be mixed

with other commercial wastes for disposal.

23 BN68-00882C-01Cover.qxd 10/10/05 3:08 PM Page 1

Precautions When Displaying a Still Image

A still image may cause permanent damage to the TV screen.

•

Digital Ready TV: When you

select the regular screen (4:3)

mode to watch an SD-grade

digital broadcast (and the set-top

box output is 480p).

Although digital broadcasting must be in the

wide screen (16:9) HD format, broadcasters

sometimes show programs made originally

in the regular screen format (4:3) by

converting the signals into digital form, in

which case the left and right side edges of

the screen are cropped.

Do not leave the screen in pause mode for

extended periods of time as you may

experience temporary or permanent image

burn.

Note : If the borders at the left, right and the

center of the screen remain fixed for

an extended period of time, the

amount of light transmission will also

remain varied and as a result the

borders may leave traces.

•

Digital Ready TV: When you

select the wide screen (16:9)

mode to watch an SD-grade

digital broadcast (and the set-top

box output is 1080i).

•

Digital Ready TV: When the

TV receives HD-grade signals

(and the set-top box output is 1080i).

When you watch a digital HD-grade

broadcast on a regular (4:3) TV with the

screen size "16:9" or "Panorama" selected,

you will be able to watch the program but the

top and bottom edges of the screen will be

cropped.

Do not leave the screen in pause mode for

extended periods of time as you may

experience temporary or permanent image

burn.

Note : If the borders at the top, bottom and

the center of the screen remain fixed

for an extended period of time, the

amount of light transmission will also

remain varied and as a result the

borders may leave traces.

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 2

• Integrated

Digital TV

(Wide-screen): When the TV

receives SD-grade (regular)

broadcasting signals (receives

480p regular signals).

•

Digital Ready TV

(wide-screen):

digital TV: When the TV receives

SD-grade (regular) broadcasting

signals (with a set-top box).

• When you watch an analog

(regular) broadcast on a

wide-screen TV (with the 4:3 screen

mode selected).

Although digital broadcasting must be in the

wide screen (16:9) HD format, broadcasters

sometimes show programs made originally

in the regular screen format (4:3) by

converting the signals into digital form, in

which case the left and right side edges of

the screen are cropped.

Do not leave the screen in pause mode for

extended periods of time as you may

experience temporary or permanent image

burn.

Note : If the borders at the left, right and the

center of the screen remain fixed for

an extended period of time, the

amount of light transmission will also

remain varied and as a result the

borders may leave traces.

•

When you watch a DVD, CD or a

video in wide-screen (21:9) format

on a wide-screen (16:9) TV.

• When you connect a computer or a

game console to the TV and select

the 4:3 screen mode.

If you connect a DVD player, computer or a

game console to the wide-screen TV and

watch a movie or play a game in regular

(4:3) or wide (21:9) screen mode, the left

and right side edges, or the top and bottom

edges of the screen will be cropped.

Do not leave the screen in pause mode for

extended periods of time as you may

experience temporary or permanent image

burn.

Note : If the borders at the left, right and the

center of the screen remain fixed for

an extended period of time, the

amount of light transmission will also

remain varied and as a result the

borders may leave traces.

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 3

English-2

Contents

CONNECTING AND PREPARING YOUR TV

Viewing the Control Panel ......................................................................................... 4

Viewing the Connection Panel................................................................................... 5

- Connecting an Aerial or Cable Television Network ............................................... 6

- Connecting Component Devices (DTV/DVD) ....................................................... 6

- Connecting External A/V Devices .......................................................................... 6

- SERVICE ................................................................................................................ 6

- Connecting Set-Top Box, VCR or DVD ................................................................. 6

- Connecting Computer ............................................................................................ 7

- Connecting AUDIO ................................................................................................. 7

- Kensington Lock ..................................................................................................... 7

Viewing the Remote Control (All Functions Except Teletext) ................................... 8

Viewing the Remote Control (Teletext Functions)..................................................... 9

Installing Batteries in the Remote Control................................................................. 10

Switching On and Off................................................................................................. 11

Placing Your Television in Standby Mode ................................................................. 11

Becoming Familiar with the Remote Control ............................................................ 12

Plug and Play ............................................................................................................. 13

Choosing Your Language .......................................................................................... 14

SETTING THE CHANNELS

Storing Channels Automatically................................................................................. 15

Storing Channels Manually........................................................................................ 16

Editing the Channels.................................................................................................. 18

Sorting the Stored Channels ..................................................................................... 19

Assigning Channels Names ...................................................................................... 20

Fine Tuning Channel Reception ................................................................................ 21

SETTING THE PICTURE

Changing the Picture Standard ................................................................................. 22

Adjusting the Custom Picture .................................................................................... 23

Changing the Colour Tone......................................................................................... 24

Resetting the Picture Settings to the Factory Defaults............................................. 24

Changing the Picture Size ......................................................................................... 25

Using the Digital NR (Digital Noise Reduction) Feature........................................... 26

DNIe (Digital Natural Image engine) ......................................................................... 27

My Colour Control ...................................................................................................... 28

Dynamic Contrast....................................................................................................... 29

Brightness Sensor...................................................................................................... 30

Viewing the Picture In Picture (PIP) .......................................................................... 31

SETTING THE SOUND

Adjusting the Volume ................................................................................................. 33

Switching the Sound Off Temporarily ........................................................................ 34

Selecting the Sound Mode ........................................................................................ 34

Changing the Sound Standard .................................................................................. 35

Adjusting the Sound Settings .................................................................................... 35

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 2

English-3

Contents

SETTING THE SOUND

Setting the TruSurround XT (SRS TSXT) .......................................................... 36

Adjusting the Volume Automatically.................................................................... 37

Connecting Headphones .................................................................................... 38

Selecting the Internal Mute ................................................................................ 38

Listening to the Sound of the Sub Picture.......................................................... 39

SETTING THE TIME

Setting and Displaying the Current Time............................................................ 40

Setting the Sleep Timer ...................................................................................... 41

Switching the Television On and Off Automatically ............................................ 42

Activating the Child Lock .................................................................................... 43

SETTING THE OTHERS

Setting the Blue Screen Mode ............................................................................ 44

Selecting the Melody .......................................................................................... 44

Selecting a Device from External Sources ........................................................ 45

Viewing Pictures from External Sources ............................................................ 46

SETTING THE PC

Setting up Your PC Software (Based on Windows XP) .................................... 47

Adjusting the PC Screen Automatically .............................................................. 48

Coarse and Fine Tuning of the Image................................................................ 49

Changing the Image Position.............................................................................. 50

Initializing the Image Settings ............................................................................ 51

USING THE TELETEXT FEATURE

Teletext Decoder.................................................................................................. 52

Displaying the Teletext Information .................................................................... 52

Selecting a Specific Teletext Page...................................................................... 53

Using Fastext to Select a Teletext Page ............................................................ 54

Storing Teletext Pages ........................................................................................ 54

RECOMMENDATIONS FOR USE

Troubleshooting: Before Contacting Service Personnel .................................... 55

Installing the Wall Mount Kit................................................................................ 56

Installing the Stand .............................................................................................. 58

Using the Anti-Theft Kensington Lock ................................................................ 59

Technical and Environmental Specifications .................................................... 60

Display Mode (PC) .............................................................................................. 61

Pin Configurations .............................................................................................. 62

Press Important Note

Symbols

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 3

English-4

Viewing the Control Panel

SOURCE

Displays a menu of all of the available input sources

(TV, Ext. 1, Ext. 2, AV, S-Video, Component, PC).

You can also use the SOURCE button on the TV’s

control panel to make selections.

MENU

Press to see an on-screen menu of

your TV’s features.

-

+

Press to decrease or increase the volume.

Also used to select items on the

on-screen menu.

Press to change channels.

Also press to highlight various items

on the on-screen menu.

(Without the Remote Control, You can

turn on TV by using the Channel buttons.)

(Power)

Press to turn the TV on and off.

Power Indicator

Blinks and turns off when the power is on and lights

up in stand-by mode.

Light Detecting Sensor

Adjusts brightness of screen automatically by detecting

brightness of surrounding environment. This sensor works

when Brightness Sensor is on.

Remote Control Sensor

Aim the remote control towards this spot on the TV.

Speakers

< LE23R51B >

< LE23R41B >

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 4

English-5

Viewing the Connection Panel

Whenever you connect an audio or video system to your set, ensure that all

elements are

switched of

f

.

Power Input

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 5

English-6

Viewing the Connection Panel

Connecting an Aerial or Cable Television Network

To view television channels correctly, a signal must be received by the set from one of the following sources:

- An outdoor aerial

-Acable television network

-Asatellite network

Connecting Component Devices (DTV/DVD)

- Connect component video cables to component connector (“PR”, “PB”, “Y”) on the rear of your set and

the other ends to corresponding component video out connectors on the DTV or DVD.

- If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box to the

DTV (or DVD) and connect the DTV (or DVD) to component connector (

“PR”, “PB”, “Y”) on your set.

- The Y, Pb and Pr connectors on your component devices (DTV or DVD) are sometimes labeled Y, B-Y and

R-Y or Y, Cb and Cr.

- Connect RCA audio cables to “

R - AUDIO - L” on the rear of your set and the other ends to

corresponding audio out connectors on the DTV or DVD.

Connecting External A/V Devices

- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD or Camcorder.

- Connect RCA audio cables to “

R - AUDIO - L” on the rear of your set and the other ends to

corresponding audio out connectors on the A/V device.

- Headphone may be connected to the headphone output ( ) on the rear of your set. While the

headphone is connected, the sound from the built-in speakers will be disabled.

SERVICE

- Connector for engineer.

Connecting Set-Top Box, VCR or DVD

- Connect the VCR or DVD SCART cable to the SCART connector of the VCR or DVD.

- If you wish to connect both the Set-Top Box and VCR (or DVD), you should connect the Set-Top Box

to the VCR (or DVD) and connect the VCR (or DVD) to your set.

Input/Output Specification

Connector

SCART 1 (EXT 1)

SCART 2 (EXT 2)

Video Audio (R/L) S-Video RGB Video+Audio (R/L)

Only TV Out

Monitor Out

(TV/Ext. 1/Ext. 2/AV/S-VHS)

Input Output

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 6

English-7

Viewing the Connection Panel

Connecting Computer

- Connect the D- Sub cable to “PC (PC IN)” on the rear of your set and the other end to the Video Card of

your computer.

- Connect the stereo audio cable to “

AUDIO (PC IN)” on the rear of your set and the other end to

“Audio Out” of the sound card on your computer.

Connecting AUDIO

- Connect RCA audio cables to “R - AUDIO - L” on the rear of your set and the other ends to corresponding

audio in connectors on the Amplifier or DVD Home Theater.

Kensington Lock

- Refer to “Using the Anti-Theft Kensington Lock” on page 59.

Speaker SCART2 Out & Audio Out

RF Scart, AV, S-Video

Component, PC

RF

Scart, AV, S-Video

Component, PC

Internal Mute Off

Speaker Output Speaker Output Speaker Output Sound Output Sound Output Sound Output

Internal Mute On

Mute Mute Mute Sound Output Sound Output Sound Output

Video No Signal

Mute Mute Mute Mute Sound Output Sound Output

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 7

English-8

Number buttons for

direct channel access

The performance of the remote control may be affected by bright light.

Television Standby button

(Refer to page 11)

Temporary sound switch-off

(Refer to page 34)

Menu display and

change confirmation

(Refer to page 12)

Automatic Power-off

(Refer to page 41)

Sound mode selection

(Refer to page 34)

Picture-In-Picture On /Off

(Refer to pages 31~32)

Sound effect selection

(Refer to page 35)

Selects the TV mode directly

-Volume increase

-Volume decrease

(Refer to page 33)

Viewing the Remote Control (All Functions Except Teletext)

Previous channel

Available source selection

(Refer to page 46)

Use to see information on the

current broadcast.

(Refer to page 40)

Control the cursor in the menu

(Refer to page 12)

Picture effect selection

(Refer to page 22)

SRS TSXT selection

(Refer to page 36)

Exit the OSD

-Next channel

-Previous channel

(Refer to page 12)

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 8

English-9

Viewing the Remote Control (Teletext Functions)

Exit from the teletext display

P: Te letext next page

P: Te letext previous page

Teletext Function : Refer to pages 52-54 for details

Tele text hold

Teletext mode selection

(LIST/FLOF)

Teletext reveal

Tele text display/mix both

teletext information and the

normal broadcast

Teletext index

Teletext sub page

Tele t ext cancel

Tele text size selection

Tele text store

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 9

English-10

Installing Batteries in the Remote Control

1 Slide the cover out completely.

2 Install two AAA size batteries.

Make

sure to match the “+” and “–” ends of the batteries with

the diagram inside the compartment.

3 Replace the cover.

Remove the batteries and store them in a cool, dry place

if you won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

If the remote control doesn’t work!

Check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 10

English-11

Switching On and Off

Your set can be placed in standby mode in order to reduce the power

consumption. The standby mode can be useful when you wish to

interrupt viewing temporarily (during a meal, for example).

1 Press the

POWER

button on the remote control.

Result

:

The screen is turned off and a red standby indicator

appears on the front of your set.

2 To switch your set back on, simply press the

POWER

, numeric

buttons (

0~9) or channel up/down ( / ) button again.

Do not leave your set in standby mode for long periods of time (when you are

away on holiday, for example).

It is best to unplug the set from the mains and aerial.

The mains lead is attached to the rear of your set.

1 Plug the mains lead into an appropriate socket.

Result

:

The standby indicator lights up on the front panel.

The main voltage is indicated on the rear of your set and the

frequency is 50 or 60Hz.

2 Press the

POWER

button on the front of the panel.

Result

:

The programme that you were watching last is reselected

automatically.

3 Press the numeric button (0~9) or channel up/down ( / ) button

on the remote control or button on the right side of the

panel.

When you switch the set on for the very first time, you will be

asked to choose language in which the menus are to be

displayed (see page 14).

4 To switch your set off, press the

POWER

button again.

Placing Your Television in Standby Mode

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 11

English-12

Becoming Familiar with the Remote Control

The remote control is used mainly to:

Change channels and adjust the volume.

Set up your set using the on-screen menu system.

The following table presents the most frequently used buttons and

their functions.

Button Viewing Function Menu Function

Used to display the

-

next stored channel.

Used to display the

-

previous stored channel.

to Used to display the corresponding channels.

For double digit channels, the second digit

must be pushed immediately after the first.

Failure to do this will result in a single digit

channel being displayed.

Used to increase the

-

volume.

Used to decrease the

-

volume.

MUTE

Used to switch the sound off temporarily.

To turn the sound back on, press this button

again, or press the / button.

MENU

Used to display the Used to return to the

on-screen menu system. previous menu or

normal viewing.

EXIT

Used to exit the on-screen menu system.

Used to move among the menu items.

Used to select a menu item or increase

the value of the selected item.

Used to return to the previous menu item or

decrease the value of the selected item.

-

Used to confirm your

ENTER

choice.

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 12

English-13

Plug and Play

When the set is initially powered ON, several basic customer settings

proceed automatically and subsequently.

The following settings are available.

1 If the set is in standby mode, press the

POWER

button on the

remote control.

Result

: The message

Start Plug & Play.

is displayed. It

appears for a little while, and then the

Language

menu

is automatically displayed.

2 Select the appropriate

language

by pressing the or button.

The available languages are listed

.

You can choose one of 21 languages.

3 Press the

ENTER

button to confirm your choice.

Result: The message

Check antenna input.

is displayed with

the

OK

selected.

4 Press the

ENTER

button.

Result

: The following areas are available:

Belgium - France - Germany - Italy -

Netherlands - Spain - Sweden - Switzerland -

United Kingdom - Eastern Europe- Others

5 Select your Country by pressing the or button.

Press the

ENTER

button.

Result

:

The

Auto Store

menu is displayed with the

Start selected.

6 Press the

ENTER

button.

Result

:

The channel search will start and end automatically.

7 Press the

ENTER

button.

Select the

hour

or

minute

by pressing the or button.

Set the

hour

or

minute

by pressing the or button.

(Refer to “

Setting and Displaying the Current Time” on page 40)

8 Press the

ENTER

button to confirm your setting.

Result

:

The

message

Enjoy your watching.

is displayed, and

then the channel which has been stored will be activated.

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 13

English-14

Plug and Play

If you want to reset this feature...

1 Press the

MENU

button.

Result

:

The main menu is displayed.

2 Press the or button to select

Setup

.

Press the

ENTER

button

.

Result:

The options available in the

Setup

group are displayed.

3

The

Plug & Play

is selected.

4 Press the

ENTER

button

.

Result

:

The message

Start Plug & Play.

is displayed.

5 For further details on how to set, refer to the previous page.

Choosing Your Language

When you start using your set for the first time, you must select the

language which will be used for displaying menus and indications.

1 Press the

MENU

button.

Result

:

The main menu is displayed.

2 Press the or button to select

Setup

.

Result

:

The options available in the

Setup

group are displayed.

3 Press the

ENTER

button

.

4 Press the or button

to

select

Language

.

Press the

ENTER

button

.

Result

:

The available

languages

are listed.

5 Select a particular language by pressing the or button

repeatedly.

Press the

ENTER

button

.

You can choose one of 21 languages.

6 When you are satisfied with your choice, press the

EXIT

button to

return to normal viewing.

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 14

English-15

Storing Channels Automatically

You can scan for the frequency ranges available to you (and availability

depends on your country). Automatically allocated programme numbers

may not correspond to actual or desired programme numbers. However,

you can sort numbers manually and clear any channels you do not wish

to watch.

1 Press the

MENU

button.

Result

:

The main menu is displayed.

2 Press the or button to select

Channel

.

Result

:

The options available in the

Channel

group are displayed.

3 Press the

ENTER

button

.

Result:

The

Country

is selected.

4 Press the

ENTER

button again

. Select your

Country

by pressing the

or

button repeatedly.

Result:

The following countries are available:

Belgium - France - Germany - Italy -

Netherlands - Spain - Sweden - Switzerland -

United Kingdom - Eastern Europe- Others

5 Press the

ENTER

button

.

6 Press the or button to select

Auto Store

.

Press the

ENTER

button

.

Result: The Auto Store menu is displayed with the Start selected.

7 Press the

ENTER

button to search the channels. The sub menu

is changed from

Start

to

Stop

with channel search started.

Result

: The search will end automatically. Channels are sorted

and stored in an order which reflects their position in the

frequency range (with lowest first and highest last).

The programme originally selected is then displayed.

To return to the previous menu, press the MENU button.

To stop the search before it has finished, press the

ENTER

button with Stop selected.

8 When the channels have been stored, you can:

Sort them in the order required (refer to page 19)

Assign names to the stored channels (refer to page 20)

Add or delete the channels (refer to page 18)

Fine tune channel reception if necessary (refer to page 21)

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 15

You can store up to 100 channels, including those received via cable

networks. When storing channels manually, you can choose:

Whether or not to store each of the channels found.

The programme number of each stored channel which you

wish to identify.

1 Press the

MENU

button.

Result

:

The main menu is displayed.

2 Press the or button to select

Channel

.

Result:

The options available in the

Channel

group are

displayed.

3 Press the

ENTER

button

.

4 Press the or button

to

select

Manual Store

.

Press the

ENTER

button.

Result

: The options available in the

Manual Store

menu are

displayed with

Programme

selected.

5 Press the

ENTER

button again.

To assign a programme number to a channel, find the correct

number by pressing the or button and then press the

ENTER

button

.

You can also set a programme number by pressing number

buttons on the remote control.

6 Press the or button to select

Colour System

and then press

the

ENTER

button.

Select the

colour

standard required by pressing the or button

repeatedly and then press the

ENTER

button.

Result

: The colour standards are displayed in the following order:

AUTO - PAL - SECAM - NTSC 4.43

7 Press the or button to select

Sound System

and then press

the

ENTER

button.

Select the sound standard required by pressing the or button

repeatedly and then press the

ENTER

button.

Result

: The sound standards are displayed in the following order:

BG - DK - I - L

8 For all the channels to move to the required channel numbers,

repeat steps

5 to 7 after selecting

Programme

by pressing

or button

.

English-16

Storing Channels Manually

23 BN68-00882C-01Eng.qxd 10/10/05 3:09 PM Page 16

9 If you know the number of the channel to be stored,

Press the or button to select

Channel

and then press the

ENTER

button.

Select C (Air channel) or S (Cable channel) by pressing the

or button.

Press the button to select channel.

Select the required number by pressing the or button and

then press the

ENTER

button.

If there is an abnormal sound or no sound, re-select the sound

system required.

You can also set a

channel

by pressing number buttons on the

remote control.

10 If you do not know the channel numbers, press the or button

to select

Search

and then press the

ENTER

button.

Search

by pressing

the

or button and then press the

ENTER

button.

Result

: The tuner scans the frequency range until the first

channel or the channel that you selected is received on

your screen.

11 Press the or button to select

Store

.

Select

OK

by pressing the

ENTER

button.

Result

: The channel and associated programme number are

stored.

12 Repeat steps 9 to 11 for each channel to be stored.

Channel mode

P (Programme mode): When tuning is completed, the

broadcasting stations in your area will have been assigned

to position numbers from P00 to P99. You can select a

channel by entering the position number in this mode.

C (Air channel mode): You can select a channel by

entering the assigned number to each broadcast station in

this mode.

S (Cable channel mode): You can select a channel by

entering the assigned number to each cable channel in this

mode.

English-17

Storing Channels Manually

23 BN68-00882C-01Eng.qxd 10/10/05 3:10 PM Page 17

You can exclude the channels you chose from the channels you

scanned. When you scan through the stored channels, those you have

chosen to skip are not displayed.

All channels that you do not specifically choose to skip are displayed

during scanning.

1 Press the

MENU

button.

Result

:

The main menu is displayed.

2 Press the or button to select

Channel

.

Press the

ENTER

button

.

Result:

The options available in the

Channel

group are

displayed.

3 Press the or button to select

Add/Delete

.

Press the

ENTER

button.

Result

:

The state of the current

channel

is displayed.

4 Press the / button to select the

channel

that you wish to

add

or

delete

.

Result

:

If the channel that you wish to edit is not in memory, the

Add

is selected and displayed.

Otherwise, if the channel that you wish to edit is in

memory, the

Delete

is selected and displayed.

5 Press the

ENTER

button to

add

or

delete

channel.

6 Repeat steps 4 and 5 for each channel to be added or deleted.

7 Press the

MENU

button to return to the previous menu or press

the

EXIT

button to return to normal viewing.

English-18

Editing the Channels

23 BN68-00882C-01Eng.qxd 10/10/05 3:10 PM Page 18

Page is loading ...

Samsung LE23R51BX Owner's manual

Samsung LE23R51BX Owner's manual

Related papers

Other documents