NordicTrack spacesaver se 9i User manual

Brand: NordicTrack

Model: spacesaver se 9i

Category: Fitness, gymnastics & weight training

Type: User manual

USER’S MANUAL

Serial

Number

Decal

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

Model No. PFEL31115.0

Serial No.

Write the serial number in the space

above for reference.

www.proform.com

To register your product and

activate your warranty today,

go to www.proformservice.com/

registration.

For service at any time, go to

www.proformservice.com.

Or call 1-888-533-1333

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–12 p.m. MT

Please do not contact the store.

ACTIVATE YOUR

WARRANTY

CUSTOMER CARE

This drawing shows the location(s) of the warning

decal(s). If a decal is missing or illegible, see

the front cover of this manual and request a

free replacement decal. Apply the decal in the

location shown. Note: The decal(s) may not be

shown at actual size.

TABLE OF CONTENTS

WARNING DECAL PLACEMENT

PROFORM is a registered trademark of ICON Health & Fitness, Inc.

IFIT is a registered trademark of ICON Health & Fitness, Inc. Google Maps is a trademark of Google Inc.

Wi-Fi is a registered trademark of Wi-Fi Alliance. WPA and WPA2 are trademarks of Wi-Fi Alliance.

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

HOW TO USE THE ELLIPTICAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

LIMITED WARRANTY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read

all important precautions and instructions in this manual and all warnings on your elliptical before

using your elliptical. ICON assumes no responsibility for personal injury or property damage sus-

tained by or through the use of this product.

1. It is the responsibility of the owner to ensure

that all users of the elliptical are adequately

informed of all precautions.

2. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

3. The elliptical is not intended for use by

persons with reduced physical, sensory, or

mental capabilities or lack of experience and

knowledge, unless they are given supervi-

sion or instruction about use of the elliptical

by someone responsible for their safety.

4. Use the elliptical only as described in this

manual.

5. The elliptical is intended for home use only.

Do not use the elliptical in a commercial,

rental, or institutional setting.

6. Keep the elliptical indoors, away from mois-

ture and dust. Do not put the elliptical in a

garage or covered patio, or near water.

7. Place the elliptical on a level surface, with at

least 3 ft. (0.9 m) of clearance in the front and

rear of the elliptical and 2 ft. (0.6 m) on each

side. To protect the floor or carpet from dam-

age, place a mat under the elliptical.

8. Inspect and properly tighten all parts each

time the elliptical is used. Replace any worn

parts immediately.

9. Keep children under age 12 and pets away

from the elliptical at all times.

10. When connecting the power cord (see page

15), plug the power cord into a grounded

circuit.

11. Do not modify the power cord or use an

adapter to connect the power cord to an

improper receptacle. Keep the power cord

away from heated surfaces. Do not use an

extension cord.

12. Do not operate the elliptical if the power cord

or plug is damaged, or if the elliptical is not

working properly.

13. DANGER: Always unplug the power

cord and switch the power switch to the off

position when the elliptical is not in use and

before cleaning the elliptical. Servicing other

than the procedures in this manual should

be performed by an authorized service repre-

sentative only.

14. The elliptical should not be used by persons

weighing more than 350 lbs. (159 kg).

15. Wear appropriate clothes while exercising;

do not wear loose clothes that could become

caught on the elliptical. Always wear athletic

shoes for foot protection while exercising.

16. Hold the handlebars or the upper body arms

when mounting, dismounting, or using the

elliptical.

17. The heart rate monitor is not a medical

device. Various factors may affect the accu-

racy of heart rate readings. The heart rate

monitor is intended only as an exercise aid

in determining heart rate trends in general.

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

18. The elliptical does not have a freewheel; the

pedals will continue to move until the fly-

wheel stops. Reduce your pedaling speed in

a controlled way.

19. Keep your back straight while using the

elliptical; do not arch your back.

20. Over exercising may result in serious injury

or death. If you feel faint, if you become short

of breath, or if you experience pain while

exercising, stop immediately and cool down.

UTS

all

STANDARD SERVICE PLANS

Fan

Console

Tabl e t Ho lder

Upper Body Arm

Heart Rate Monitor

Wheel

Pedal

Roller

Pedal Handle

Handle

Accessory Tray

Ramp

Handlebar

Length: 6 ft. 8 in. (203 cm)

Width: 2 ft. 5 in. (74 cm)

Thank you for selecting the revolutionary PROFORM

PRO 12.9 elliptical. The PRO 12.9 elliptical provides an

impressive selection of features designed to make your

workouts at home more effective and enjoyable.

For your benefit, read this manual carefully before

you use the elliptical. If you have questions after

reading this manual, please see the front cover of this

manual. To help us assist you, note the product model

number and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

BEFORE YOU BEGIN

M10 x 75mm Screw

(142)–2

M10 Locknut

(99)–4

M10 x 20mm

Screw (144)–12

M4 x 16mm

Screw (104)–4

M10 x 45mm

Bolt (143)–4

M10 x 70mm

Screw (139)–2

#8 x 12mm

Screw (152)–4

PART IDENTIFICATION CHART

Use the drawings below to identify the small parts needed for assembly. The number in parentheses below each

drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the

key number is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it

has been preassembled. Extra parts may be included.

• To hire an authorized service technician to

assemble this product, call 1-800-445-2480.

• Assembly requires two persons.

• Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until you complete all assembly steps.

• Left parts are marked “L” or “Left” and right parts

are marked “R” or “Right.”

• To identify small parts, see page 8.

• In addition to the included tool(s), assembly

requires the following tools:

one Phillips screwdriver

one adjustable wrench

Assembly may be easier if you have your own set

of wrenches. To avoid damaging parts, do not use

power tools.

ASSEMBLY

1. Go to www.proform.com/registration on your

computer and register your product.

• activates your warranty

• saves you time if you ever need to contact

Customer Care

• allows us to notify you of upgrades and offers

Note: If you do not have Internet access, call

Customer Care (see the front cover of this

manual) and register your product.

2. With the help of a second person, place some of

the packing materials (not shown) under the rear

of the Frame (1). Have the second person hold

the Frame to prevent it from tipping while you

complete this step.

Identify the two Rear Stabilizers (5).

Attach one of the Rear Stabilizers (5) to the

Frame (1) with three M10 x 20mm Screws (144);

start all of the Screws, and then tighten them.

Attach the other Rear Stabilizer (5) in the

same way.

Then, remove the packing materials from under

the Frame (1).

144

3. Orient the Rear Stabilizer Cover (2) as shown,

and press it onto the Frame (1).

Attach the Rear Stabilizer Cover (2) with two

M4 x 16mm Screws (104).

104

4. With the help of a second person, place some of

the packing materials (not shown) under the front

of the Frame (1). Have the second person hold

the Frame to prevent it from tipping while you

complete this step. Leave the packing materi-

als in place until you complete step 5.

Identify the Right Front Stabilizer (6) and orient it

as shown.

Attach the Right Front Stabilizer (6) to the Frame

(1) with three M10 x 20mm Screws (144); start

all of the Screws, and then tighten them.

Attach the Left Front Stabilizer (not shown) in

the same way.

144

104

5. Orient the Front Stabilizer Cover (8) as shown,

and route the Power Cord (not shown) over

the top of the Front Stabilizer Cover. Then,

press the Front Stabilizer Cover onto the

Frame (1).

Attach the Front Stabilizer Cover (8) with two

M4 x 16mm Screws (104).

Then, remove the packing materials from under

the Frame (1).

6. Raise the Upright (4) to the vertical position.

Secure the Upright with two M10 x 75mm

Screws (142).

Then, slide the Shield Cover (56) downward onto

the Rear Shield (75).

142

7. Locate the Right Upper Saddle Bracket (121) on

the Right Roller Arm (45). Next, locate the Lower

Saddle Bracket (26) on the right side of the

elliptical.

Attach the Right Upper Saddle Bracket (121)

to the Lower Saddle Bracket (26) with two

M10 x 70mm Screws (139).

121

139

8. Identify the Right Upper Body Arm (61) and an

Upper Body Arm Cover (77). Slide the Upper

Body Arm Cover onto the Right Upper Body Arm

as shown.

Attach the Right Upper Body Arm (61) to

the Right Upper Body Leg (36) with two

M10 x 45mm Bolts (143) and two M10 Locknuts

(99); make sure that the Locknuts are in the

hexagonal holes.

Then, slide the Upper Body Arm Cover (77)

downward and turn it so that it is flush with the

Right Upper Body Leg (36).

Attach the Left Upper Body Arm (47) in the

same way.

Hexagonal

Holes

143

10. Make sure that all parts are properly tightened before you use the elliptical. Extra parts may be included.

Place a mat beneath the elliptical to protect the floor.

9. Attach the Tablet Holder (151) to the Console (7)

with four #8 x 12mm Screws (152); start all of

the Screws, and then tighten them.

151

152

THE CHEST HEART RATE MONITOR

HOW TO PUT ON THE HEART RATE MONITOR

If the heart rate monitor looks like the one shown

in drawing 1, press the transmitter (A) onto the snap

fasteners on the chest strap (B). If the heart rate

monitor looks like the one shown in drawing 2,

insert the tab (C) on one end of the chest strap (D) into

one end of the transmitter (E). Then, press the end of

the transmitter under the buckle (F) on the chest strap;

the tab should be flush with the transmitter.

Next, wrap the heart

rate monitor around

your chest in the loca-

tion shown; the heart

rate monitor must be

under your clothes,

tight against your skin.

Make sure that the logo

is right-side-up. Then, attach the other end of the chest

strap. Adjust the length of the chest strap, if necessary.

Next, pull the trans-

mitter and the chest

strap away from your

body a few inches

and locate the two

electrode areas (G).

Using saliva or con-

tact lens solution, wet the electrode areas. Then, return

the transmitter and the chest strap to a position against

your chest.

CARE AND MAINTENANCE

• Thoroughly dry the electrode areas with a soft towel

after each use. Moisture may keep the heart rate

monitor activated, shortening the life of the battery.

• Store the heart rate monitor in a warm, dry place. Do

not store the heart rate monitor in a plastic bag or

other container that may trap moisture.

• Do not expose the heart rate monitor to direct

sunlight for extended periods of time, and do not

expose it to temperatures above 122° F (50° C) or

below 14° F (-10° C).

• Do not excessively bend or stretch the heart rate

monitor when using or storing it.

• To clean the transmitter, use a damp cloth and a

small amount of mild soap. Then, wipe the transmit-

ter with a damp cloth and thoroughly dry it with a soft

towel. Never use alcohol, abrasives, or chemicals

to clean the transmitter. Hand wash and air dry the

chest strap.

TROUBLESHOOTING

• If the heart rate monitor does not function when

positioned as described at the left, move it slightly

lower or higher on your chest.

• If heart rate readings are not displayed until you

begin perspiring, re-wet the electrode areas.

• For the console to display heart rate readings, you

must be within arm’s length of the console.

• If there is a battery cover on the back of the trans-

mitter, replace the battery with a new battery of the

same type.

• The heart rate monitor is designed to work with

people who have normal heart rhythms. Heart rate

reading problems may be caused by medical condi-

tions such as premature ventricular contractions

(pvcs), tachycardia bursts, and arrhythmia.

• The operation of the heart rate monitor can be

affected by magnetic interference from high power

lines or other sources. If you suspect that magnetic

interference is causing a problem, try relocating the

fitness equipment.

1 2

HOW TO PLUG IN THE POWER CORD

This product must be grounded. If it should mal-

function or break down, grounding provides a path of

least resistance for electric current to reduce the risk

of electric shock. The power cord has a plug with a

grounding pin.

Plug the power

cord into an

appropriate

outlet that is

properly installed

and grounded in

accordance with

all local codes

and ordinances.

The outlet must

be on a nominal

120-volt circuit.

A temporary

adapter may be

used to con-

nect the power

cord to a 2-pole

receptacle as

shown at the

right if a prop-

erly grounded

outlet is not

available.

The lug or wire extending from the adapter must

be connected with a metal screw to a permanent

ground such as a properly grounded outlet box cover.

Some 2-pole receptacle outlet box covers are not

grounded. Before using an adapter, contact a quali-

fied electrician to determine whether the outlet

box cover is grounded before using an adapter.

The temporary adapter should be used only until

a properly grounded outlet can be installed by a

qualified electrician.

HOW TO USE THE ELLIPTICAL

DANGER: Improper connection of

the power cord increases the risk of electric

shock. Do not modify the plug; if it will not fit

an outlet, have a proper outlet installed by a

qualified electrician. If you are unsure whether

the product is properly grounded, contact a

qualified electrician.

Grounded Outlet

2-pole Receptacle

Grounding Pin

Adapter

Lug

Metal Screw

HOW TO MOVE THE ELLIPTICAL

Due to the size and weight of the elliptical, moving

it requires two persons. Stand in front of the ellipti-

cal, hold the upright, and place one foot against one

of the wheels. Have a second person lift the handle

on the rear of the frame until the elliptical will roll on

the wheels. Carefully move the elliptical to the desired

location, and then lower it to the floor.

HOW TO ADJUST THE POSITIONS OF THE

PEDALS

Each pedal can be adjusted to several positions. To

adjust each pedal, simply pull the pedal handle out-

ward, move the pedal to the desired position, and

then release the pedal handle into an adjustment hole

beneath the pedal. Make sure to adjust both pedals

to the same position.

HOW TO USE THE TABLET HOLDER

IMPORTANT: The tablet holder is designed for use

with most full-size tablets. Do not place any other

electronic device or object in the tablet holder.

To insert a tablet into

the tablet holder, set

the bottom edge of

the tablet in the tray.

Then, pull the clip over

the top edge of the

tablet. Make sure that

the tablet is firmly

secured in the tablet

holder. Rotate the tab-

let holder to the desired

angle. Reverse these

actions to remove the tablet from the tablet holder.

Upright

Lift

here

Place

your foot

here

Pedal

Handle

HOW TO LEVEL THE ELLIPTICAL

If the elliptical rocks slightly on your floor during use,

turn one or both of the leveling feet beneath the rear

stabilizer or beneath the frame until the rocking motion

is eliminated.

HOW TO EXERCISE ON THE ELLIPTICAL

To m o unt the e llip tica l , h o ld t he u p per body arm s or

the handlebars and step onto the pedal that is in the

lower position. Then, step onto the other pedal. Push

the pedals until they begin to move with a continuous

motion. Note: The crank arms can turn in either

direction. It is recommended that you turn the

crank arms in the direction shown by the arrow;

however, for variety, you can turn the crank arms in

the opposite direction.

To d i smou nt t h e el lipt i cal , wai t un t il t he p e dal s com e to

a complete stop. Note: The elliptical does not have

a free wheel; the pedals will continue to move until

the flywheel stops. When the pedals are stationary,

step off the higher pedal first. Then, step off the lower

pedal.

Leveling Feet

Leveling

Foot

Pedal

Crank

Arm

Upper Body

Arm

Handlebar

MAKE YOUR FITNESS GOALS A REALITY WITH

IFIT.COM

With your new iFit-compatible fitness equipment, you

can use an array of features on iFit.com to make your

fitness goals a reality:

Exercise anywhere in the world with

customizable Google Maps.

Download training workouts designed to

help you reach your personal goals.

Measure your progress by competing

against other users in the iFit community.

Upload your workout results to the iFit cloud

and track your accomplishments.

Set calorie, time, or distance goals for your

workouts.

Choose and download sets of weight-loss

workouts.

Go to iFit.com to learn more.

Watch high-definition videos with simulated

workouts.

CONSOLE DIAGRAM

FEATURES OF THE CONSOLE

The advanced console offers an array of features

designed to make your workouts more effective and

enjoyable.

The console features revolutionary iFit technology that

enables the console to communicate with your wireless

network. With iFit technology, you can download per-

sonalized workouts, create your own workouts, track

your workout results, and access many other features.

See www.iFit.com for complete information.

In addition, the console features a selection of onboard

workouts and several iFit demo workouts. Each work-

out automatically controls the resistance of the pedals

and the incline of the ramp and prompts you to vary

your pedaling speed as it guides you through an effec-

tive exercise session. You can also set a customized

workout goal with the set-a-goal workout.

When you use the manual mode of the console, you

can change the resistance of the pedals and the incline

of the ramp with the touch of a button.

While you exercise, the console will display continuous

exercise feedback. You can also measure your heart

rate using the handgrip heart rate monitor or the chest

heart rate monitor.

You can also browse the Internet or listen to your

favorite workout music or audio books with the console

sound system while you exercise.

To turn on the power, see this page. To learn how to

use the touch screen, see page 20. To set up the

console, see page 20.

HOW TO TURN ON THE POWER

IMPORTANT: If the elliptical has been exposed to

cold temperatures, allow it to warm to room tem-

perature before you turn on the power. If you do

not do this, you may damage the console displays

or other electrical components.

Plug in the power cord (see

HOW TO PLUG IN THE

POWER CORD on page

15). Next, locate the

power switch on the frame

near the power cord. Press

the power switch to the

reset position.

The display will then turn on and the console will be

ready for use.

Note: When you turn on the power for the ﬁ rst time,

the incline system may calibrate automatically. The

ramp will move upward and downward as it calibrates.

When the ramp stops moving, the incline system is

calibrated.

IMPORTANT: If the incline system does not cali-

brate automatically, see step 4 on page 28 and

manually calibrate the incline system.

IMPORTANT: The console features a display demo

mode, designed to be used if the elliptical is dis-

played in a store. If the demo mode is turned on,

the console will show a preset presentation when

you ﬁ nish exercising. To turn off the demo mode,

see step 6 on page 26.

Reset

Position

HOW TO USE THE TOUCH SCREEN

The console features a tablet with a full-color touch

screen. The following information will help you become

familiar with the tablet’s advanced technology:

• The console functions similarly to other tablets. You

can slide or flick your finger against the screen to

move certain images on the screen, such as the

displays in a workout. However, you cannot zoom in

and out by sliding your fingers on the screen.

• To type information into a text box, first touch the text

box to view the keyboard. To use numbers or other

characters on the keyboard, touch the ?123 button.

To v i ew m ore c hara cter s , t o uch the Alt butt o n. Touc h

the Alt button again to return to the number key-

board. To return to the letter keyboard, touch the

ABC button. To use a capital character, touch the

button with an upward-facing arrow. To use multiple

capital characters, touch the arrow button again. To

return to the lowercase keyboard, touch the arrow

button a third time. To clear the last character, touch

the button with a backward-facing arrow and an X.

• Use these buttons on

the console to navigate

the tablet. Press the

home button to return to

the main menu. Press

the settings button to

access the settings

menu (see page 26).

Press the back button to return to the previous

screen.

HOW TO SET UP THE CONSOLE

Before using the elliptical for the first time, set up the

console.

1. Connect to your wireless network.

Note: In order to access the Internet, download iFit

workouts, and use some other features of the con-

sole, you must be connected to a wireless network.

See HOW TO USE THE WIRELESS NETWORK

MODE on page 29 to connect the console to

your wireless network.

2. Check for firmware updates.

First, see step 1 on page 26 and step 2 on page

28 and select the maintenance mode. Then,

see step 3 on page 28 and check for firmware

updates.

3. Calibrate the incline system.

See step 4 on page 28 and calibrate the incline

system.

4. Create an iFit account.

Touc h the glo b e bu tton at t he b otto m of the s cre e n

and then touch the iFit button.

Note: For information about navigating in the

Internet browser, see page 30.

The Internet browser will open to the iFit.com home

page. Follow the prompts on the website to sign up

for your iFit membership. If you have an activation

code, select the code activation option.

The console is now ready for you to begin working out.

The following pages explain the various workouts and

other features that the console offers.

To use the manual mode, see page 21. To use

an onboard workout, see page 23. To use a

set-a-goal workout, see page 24. To use an iFit

workout, see page 25.

To use the equipment settings mode, see

page 26. To use the maintenance mode, see page

28. To use the wireless network mode, see page

29. To use the sound system, see page 30. To

use the Internet browser, see page 30.

Note: If there is a sheet of plastic on the screen,

remove the plastic.

Note: The console can display speed and distance in

either miles or kilometers. To find which unit of mea-

surement is selected, see step 13 on page 27. For

simplicity, all instructions in this section refer to miles.

Home

Settings

Back

Page is loading ...

NordicTrack spacesaver se 9i User manual

Brand: NordicTrack

Model: spacesaver se 9i

Category: Fitness, gymnastics & weight training

Type: User manual

Download PDF

report

NordicTrack spacesaver se 9i User manual

NordicTrack spacesaver se 9i User manual

Related papers

Other documents