Hampton Bay HD28353 Installation guide

Type
Installation guide

Hampton Bay HD28353 is a low voltage cable connector designed for use with landscape lighting systems. It allows for easy installation and connection of fixtures to the low voltage cable.

Here are some of the key features and capabilities of the Hampton Bay HD28353:

  • Easy installation: The Quick Clip connector replaces existing connectors and allows installation anywhere along the low voltage cable.
  • Twist-on wire connectors: The provided twist-on wire connectors make it easy to connect existing fixture wires to the pigtail wires of the Quick Clip connector.
  • Pre-set prongs: The pre-set prongs pierce the cable insulation and establish contact, ensuring a secure connection.

Hampton Bay HD28353 is a low voltage cable connector designed for use with landscape lighting systems. It allows for easy installation and connection of fixtures to the low voltage cable.

Here are some of the key features and capabilities of the Hampton Bay HD28353:

  • Easy installation: The Quick Clip connector replaces existing connectors and allows installation anywhere along the low voltage cable.
  • Twist-on wire connectors: The provided twist-on wire connectors make it easy to connect existing fixture wires to the pigtail wires of the Quick Clip connector.
  • Pre-set prongs: The pre-set prongs pierce the cable insulation and establish contact, ensuring a secure connection.
WARNING: Risk of Electric Shock. Install 10 feet or more from a pool, spa or fountain. Be protected by routing in
close proximity to the luminaire or tting or next to a building structure such as a house or deck; Not to be buried
except for a maximum 6 inches in order to connect the main low voltage cable; and have the length cut off so that it is
connected to a connector within 6 inches from a building structure, a luminaire or tting.
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY
THIS DEVICE IS ACCEPTED AS A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM WHERE THE SUITABILITY
OF THE COMBINATION SHALL BE DETERMINED BY CSA OR LOCAL INSPECTION AUTHORITIES HAVING
JURISDICTION
EASY TO INSTALL
1. The Quick Clip connector replaces existing connectors and allows installation anywhere along the low voltage cable.
2. Connect existing xture wires to “pigtail” wires of Quick Clip connector, using the twist-on wire connectors provided. (Fig.1)
3. Place the wire connector on opposite sides of the low voltage cable where the xture will be located. (Fig. 1)
4. Press the wire connector together until fully seated and locked around the cable. Pre-set prongs will pierce the cable insulation
and establish contact.
5. Once the connector is in place, it is recommended to wrap it with electrical tape (not included) for additional protection. (Fig. 2)
Additional wire can be purchased at your local hardware retailer.
Item #1001 491 871
Model #HD28353
Quick Clip connector
Wire connectors
Fixture
Low voltage
cable
Existing xture wires
Fig. 1 Fig. 2
ADVERTENCIA: Riesgo de electrocución. Instale a una distancia de 3.05 m (10 pies) o más de una piscina, spa o
fuente. Protéjase tendiendo la línea cerca de la lámpara o del acople, o al lado de un edicio, tal como una casa o
terraza; no debe enterrarse, salvo un máximo de 15 cm (6") para conectar el cable principal de bajo voltaje; y recorte
la longitud del cable de manera que quede conectado a un conector a 15 cm o menos de un edicio, lámpara o
acople.
PARA USAR CON SISTEMAS DE ILUMINACIÓN PARA JARDINES ÚNICAMENTE
EL DISPOSITIVO ES ACEPTADO COMO UN COMPONENTE DE UN SISTEMA DE ILUMINACIÓN PARA JARDINES
DONDE LA IDONEIDAD DE LA COMBINACIÓN DEBERÁ DETERMINARSE POR CSA O LAS AUTORIDADES
LOCALES DE INSPECCIÓN CON JURISDICCIÓN
FÁCIL DE INSTALAR
1. Quick Clip reemplaza los conectores existentes y permite una instalación en cualquier punto a lo largo del cable de bajo voltaje.
2. Conectar los hilos de la lámpara a los hilos del conector con ayuda de los conectores de hilo proporcionados. (Fig.1)
3. Coloque el conector para alambres en los lados opuestos del cable de bajo voltaje dónde el accesorio será ubicado. (Fig. 1)
4. Apriete el conector para alambres hasta que quede bien posicionado y jo alrededor del cable. Los dientes
pre-posicionados se agarrarán al aislamiento del cable y establecerán contacto.
5. Una vez en su lugar, se recomienda para envolver el conector de enganche con cinta eléctrica. (Fig. 2)
Se puede adquirir cableado adicional en su ferretería loca.
Núm. de artículo 1001 491 871
Núm. de modelo HD28353
Conector Quick Clip
Conectores de hilo
Accesorios
Cable de
bajo voltaje
Hilos existentes del lámpara
Fig. 1 Fig. 2
  • Page 1 1
  • Page 2 2

Hampton Bay HD28353 Installation guide

Type
Installation guide

Hampton Bay HD28353 is a low voltage cable connector designed for use with landscape lighting systems. It allows for easy installation and connection of fixtures to the low voltage cable.

Here are some of the key features and capabilities of the Hampton Bay HD28353:

  • Easy installation: The Quick Clip connector replaces existing connectors and allows installation anywhere along the low voltage cable.
  • Twist-on wire connectors: The provided twist-on wire connectors make it easy to connect existing fixture wires to the pigtail wires of the Quick Clip connector.
  • Pre-set prongs: The pre-set prongs pierce the cable insulation and establish contact, ensuring a secure connection.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages