DAVIS Spar-Fly, (1310) Owner's manual

Type
Owner's manual

This manual is also suitable for

Davis Instruments Spar-Fly, (1310) is a wind indicator designed for mounting on any masthead. It features spoiler holes for increased accuracy, a needle bearing balance for high sensitivity, and high-impact plastic construction for durability. Weighing only 1.25 oz., it is unaffected by the angle of heel and comes with hardware for top mounting or quick-release side mounting. With its highly visible vane and marine-grade metals, Spar-Fly is an excellent choice for sailors looking for a reliable and easy-to-use wind indicator.

Davis Instruments Spar-Fly, (1310) is a wind indicator designed for mounting on any masthead. It features spoiler holes for increased accuracy, a needle bearing balance for high sensitivity, and high-impact plastic construction for durability. Weighing only 1.25 oz., it is unaffected by the angle of heel and comes with hardware for top mounting or quick-release side mounting. With its highly visible vane and marine-grade metals, Spar-Fly is an excellent choice for sailors looking for a reliable and easy-to-use wind indicator.

#1310
Spar-Fly
INSTRUCTIONS
Davis Spar-Fly is a wind indicator which mounts on any mast-
head. Spoiler holes reduce lift and increase accuracy. Needle
bearing balance provides high sensitivity. Highly visible from
deck. High impact plastic vane and marine grade metals for
unsurpassed durability. Weighs only 1.25 oz. (35 g). Spar-Fly
is unaffected by angle of heel. Hardware included for either
top mounting or quick-release side mounting.
Assembling the Vane
Insert spire downward from top into plastic chassis
(as shown below).
Do NOT attempt to insert from the bottom. Follow
these instructions precisely. Now, with finger, press
needle bearing housing into hole in top of plastic
chassis. Continue to press housing against a solid
object (such as a table) until it is seated, but don’t
press so hard that spire bearing becomes jammed.
Test to make sure vane spins freely on spire. No
lubrication is necessary.
Balancing the Unit
Hold Spar-Fly at a 45° angle to the floor and adjust
weight and locking nut until it is in lateral balance
(as shown below).
When balanced, tighten nut. Test sensitivity by walk-
ing past Spar-Fly in a closed area before mounting.
America’s Most
Popular Wind Finder!
On wood spars, attach base to masthead using long
brass wood screws.
On metal spars, use stainless steel self-tapping
screws provided. Otherwise drill and tap a 6-32 hole
to take the threaded spire, then install nut and lock
washer and tighten.
3465 Diablo Ave., Hayward, CA 94545 U.S.A.
Phone (510) 732-9229 • Fax (510) 732-9188
inf[email protected] www.davisnet.com
1310_Ins.pdf June 2007
Replacement Vane is available from your local dealer
or Davis Instruments. Ask for #1311.
TIP: Knowing wind direction
makes docking easier.
Install a Spar-Fly near your
berth.
Using the Top Mount Fitting. Screw on nut, lock
washer, and mounting base.
Mounting Spar-Fly
Once spire is in place and unit is balanced, choose one of two mounting methods:
Using the Quick-Release Side Mount. Position
side mount as high as possible on spar to minimize
wind turbulence.
On wood masts, use long brass wood screws.
On metal masts, use stainless steel self-tapping
screws provided.
  • Page 1 1
  • Page 2 2

DAVIS Spar-Fly, (1310) Owner's manual

Type
Owner's manual
This manual is also suitable for

Davis Instruments Spar-Fly, (1310) is a wind indicator designed for mounting on any masthead. It features spoiler holes for increased accuracy, a needle bearing balance for high sensitivity, and high-impact plastic construction for durability. Weighing only 1.25 oz., it is unaffected by the angle of heel and comes with hardware for top mounting or quick-release side mounting. With its highly visible vane and marine-grade metals, Spar-Fly is an excellent choice for sailors looking for a reliable and easy-to-use wind indicator.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI