Legrand Smart Outlet Installation guide

Type
Installation guide
installation guide
Smart Outlet
WTRR10
2
table of contents
before you start ..................................3
what you need ...................................4
installation and setup ................ 6–19
getting to know your outlet ...... 20–21
specifications ............................. 22-23
faqs ..............................................24
warranty .......................................25
regulatory information ......... 26–29
support ........................................30
notes ............................................31
3
before you start
Review this guide in its entirety before beginning device installation. Consult an
electrician with any questions or if you are unsure of your abilities.
DWarning: Incorrect installation could
result in death, serious injury, and/or
damage to your home or devices.
DCaution: To reduce the risk of injury
and/or overheating and damage to other
equipment:
For dry, indoor use only.
Do not use with loads exceeding the
device load rating (see page 22).
Connect the smart outlet to a
120 VAC, 60 Hz power source ONLY.
Always use copper wire to install the
smart outlet and follow all applicable
local and national electrical codes.
Install in a non-metallic electrical box
to protect wireless signal strength.
Visit the Legrand website at www.legrand.us/radiant/smart-lighting.aspx to learn more
about your smart device.
4
what you need
REQUIRED:
Phillips-head screwdriver
Flat blade screwdriver
YOU MAY ALSO NEED:
Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape,
flashlight, radiant
®
screwless wallplate (included), wiring leads (included), and
wire nuts (included)
NOTE: Exercise caution when using power tools. Overtightening the screws can
damage the device.
5
6
installation & setup
step one
|
turn off the power for your device at the
circuit breaker
Test a plugged-in device to confirm the power is off.
7
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
8
installation & setup
step two
|
remove the existing device
Take a picture of the wiring, then check for the following wires:
1
HOT or LINE: Receives power from the circuit box. Referred to as “Hot” for the
purposes of this guide.
2
NEUTRAL: Creates a path to return current to the power source when the
device is off. Required for your outlet installation.
3
GROUND: Provides a safe path for electricity in the event of a short circuit.
NOTE: Refer to the “faqs” on page 24 if you are unsure of your wiring.
9
VOLTAGE
TESTER
10
installation & setup
step three
|
wire the smart outlet
When connecting each wire, loosen the terminal screw, insert the wire into a
terminal slot, and tighten the terminal screw until the wire is secured.
1
Connect the neutral wire to any WHITE terminal slot.
2
Connect the hot wire to any HOT terminal slot.
3
Connect the green or bare copper ground wire to the grounding terminal of
the device.
NOTE:
If you need extra length on your wires, wire leads are included in your packaging.
Refer to the “faqs” on page 24 if you are unsure of your wiring.
11
OFF
ON
OFF
ON
OFF
ON
Terminal slot
Terminal
screw
Supply
“Hot”
12
installation & setup
step four
|
secure the smart outlet
1
Gently fold the wires into the electrical box. Be careful not to pinch a wire or
loosen anywire nuts.
2
Use the device screws to secure the smart outlet to the electrical box. Do not
fully tighten the screws.
13
Controlled
14
installation & setup
step five
|
test the smart outlet
NOTE: See page 20 for feature details.
1
Turn the power on at the circuit breaker and look for an amber indicator light
on the smart outlet to indicate that it is active.
2
Plug a lamp or device into the controlled outlet.
3
Press the on/off button to turn the smart outlet on. Your lamp or device
should become powered.
4
Press the on/off button to turn the smart outlet off. Your lamp or device
should power off.
TROUBLESHOOTING TIP:
If the device is not powering, contact technical support using the contact information
under “support” on page 30.
15
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
16
installation & setup
step six
|
attach the screwless wall plate
1
Noting which side faces out, align the sub-plate over the device screws. Use
the sub-plate screws (provided) to secure the sub-plate to the smart outlet.
2
Tighten the device screws to secure the smart outlet to the electrical box.
3
Angle the end of the screwless wall plate over the top edge of the
sub-plate. Push the screwless wall plate down and in until it “snaps” into
place over the sub-plate.
NOTE: To remove the wall plate, place the tip of a flat blade screwdriver into the slot under
the wall plate and twist gently.
17
Controlled
THIS SIDE OUT
MOUNT OVER DEVICE
Controlled
THIS SIDE OUT
MOUNT OVER DEVICE
Controlled
THIS SIDE OUT
MOUNT OVER DEVICE
1 32
18
19
installation & setup
step seven
|
set up your system
1
Download and launch the Smart Lights Thread app by Legrand. The app is
available on the App Store or on Google Play.
2
Connect your smart hub (WTH1) by following the smart hub installation guide
instructions and the self-guided app instructions.
3
Connect your smart outlet to the smart hub by following the instructions
within the app.
Google Play and the Google Play logo are trademarks of Google LLC. App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
20
getting to know your outlet
Item Name Description
1 Controlled Outlet “Switched” plug socket
2 Indicator Light
Indicates operation. See “Indicator Light
Explanations” for detail.
3 On/Off Button Turns the outlet on or off
4 Uncontrolled Outlet Always on” plug socket
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Legrand Smart Outlet Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI