Page is loading ...
Bronze 2-Tier Wardrobe
WD001
PACKAGE CONTENTS
Please inspect box contents to ensure you have received all components.
Note: the black circular plastic tops in between the shelves are used only for
packaging purposes. They are NOT NEEDED. Please discard responsibly
Total weight capacity is 270 kg on casters.
& keep away from small children.
GX28+2
AX2 BX2
CX4
DX4
Shelf
Bottom Pole (with pole connector
and threaded insert pre-installed)
Top Pole (with end
cap pre-installed)
Hanging Pole
extra Slip sleeve
FX4
EX2
Casters
(2 locking; 2 non-locking)
Swing Arm
HELP LINE
01977 555007
ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED
Never climb or stand on the shelves.
Informaon
if in doubt contact the supplier
Allow adequate working space and be
aware of others working around you
Inspect all packages for damage and
check that all components have been
supplied
Cauon
During Assembly
!
Warning
Rules for safe use of shelving
!
ENSURE THAT THE MAXIMUM LOAD
CARRYING CAPACITIES ARE NOT
EXCEEDED
Dispose of packaging materials
responsibly
Wear appropriate clothing -protecve
gloves and footwear are
recommended
Make sure the floor is level
Take care when handling heavy items
parcularly when liing or stretching
Please read these instrucons
throughly before commencing
assembly.
Assembly should be undertaken by
at least two people
Not suitable for use in damp or wet
environments.
Shelves must be loaded evenly, and load
heavier items on the boom shelves
Rubber Mallet
ASSEMBLY INSTRUCTIONS
STEP 2: SLIP SLEEVES
STEP 1: ASSEMBLING THE CASTERS
On the Bottom Pole (C), place 1 pair of slip sleeves (G) at the desired level.
Screw each Caster (F) into the bottom of each Bottom Pole (C). Turn
clock-wise to screw in place. Screw in tightly.
Please make sure the arrow faces up and that the word “top” is right side
up. Do this for each Bottom Pole (C) and make sure that the heights are
identical for Bottom Pole (C).
Slide the pair of Slip Sleeves (G) until you hear a click to confirm the pair is
locked onto the Bottom Pole (C).Do not place more than one pair
on each Pole (C) at a time.
*For safety and stability, the lowest SHELF (A) should be lower than the 3rd
notch from the bottom.
**Note: There will be a very small gap in-between the Slip Sleeves (G)-this
is normal.
STEP 3 : INSTALLING BOTTOM SHELF
STEP 4 : INSTALLING TOP POLES
Place Shelf (A) on its side and slide the Bottom Pole (C) through the holes
in the Shelf (A). Make sure that the shelf (A) corner cylinders are
positioned over the Slip sleeves (G).
Stand the unit upright.
*Note : The level side of the Shelf (A) is the Top side(the logo on the
corner cylinders should be right-side up.)
**Use a rubber mallet, if needed, to secure the Shelf (A).
Screw the Top Pole (D) into the Bottom Pole (C). The tops of these poles .
are indicated by the black end up.
STEP 5: INSTALLING SWING ARMS
Attach sleeves at desired height for Swing Arms (E). Place these 2 swing
arm pieces over the top poles until secure on sleeves push firmly together.
STEP 6: INSTALLING HANGING POLES
Repeat step 2 for the Hanging Poles (B) snd Slide Hanging Poles (B) onto
the Slip Sleeves (G).
STEP 7: INSTALLING REMAINNING SHELF
On Pole (D+C), place 1 pair of slip sleeves (G) at the highest position.
Slide Shelf (A) onto the Slip Sleeves (G).
STEP 8: FINISH
AND ENJOY YOUR QUALITY
RACKING SOLUTION PRODUCT
C
E
B
C
D
C
G
A
C
F
/
