DVR-605
DVR-6100
DVR-6100K
DVD RECEIVER
INSTRUCTION MANUAL
KENWOOD CORPORATION
B60-5262-08 01 (K/P/E/T/M/M2/X/Y)
WS
02/05
DIGITAL VIDEO
COMPACT
This instruction manual is for some models. Model availability and
features (functions) may differ depending on the country and sales
area.
*5262/01-11/EN 02.6.18, 3:09 PM1
2
DVR-605/DVR-6100/DVR-6100K (EN)
Preparations
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SER-
VICING TO QUALIFIED SERVICE PERSONNEL.
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRI-
ANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED “DAN-
GEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT
MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT
THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SER-
VICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
Units are designed for operation as follows.
Safety precautions
Factory fitted moulded mains plug
1. The mains plug contains a fuse. For replacement, use
only a 13-Amp ASTA-approved (BS 1362) fuse.
2. The fuse cover must be refitted when replacing the
fuse in the moulded plug.
3. Do not cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in
your home or the cable is too short to reach, a power
point, then obtain an appropriate safety approved
extension lead or adapter, or consult your dealer. If
nonetheless the mains plug is cut off, remove the
fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to
the mains supply.
IMPORTANT :
The wires in the mains lead are coloured in accordance
with the following code:
Blue : Neutral
Brown : Live
Do not connect those leads to the earth terminal of a
three-pin plug.
For the United Kingdom
WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
The marking this product has been classified as Class
1. It means that there is no danger of hazardous radia-
tion outside the product.
Location: Back panel
CLASS 1
LASER PRODUCT
The marking of products using lasers
(Except for some areas)
U.S.A. and Canada ....................................................... AC 120V only
Australia ....................................................................... AC 240 V only
Before applying power
Caution : Read this page carefully to ensure safe operation.
Introduction
Caution : Read this page carefully to ensure safe operation.
Europe and U.K. ............................................................ AC 230V only
*Other countries .................... AC 110-120 / 220-240 V switchable
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
*For other countries
The AC voltage selector switch on the rear panel is set
to the voltage that prevails in the area to which the unit
is shipped. Before connecting the power cord to your AC
outlet, make sure that the setting position of this switch
matches your line voltage. If not, it must be set to your
voltage in accordance with the following direction.
AC voltage selection
AC voltage selector switch
Move switch lever to match your line voltage with
a small screwdriver or other pointed tool.
Note:
Our warranty does not cover damage caused by excessive
line voltage due to improper setting of the AC voltage
selector switch.
*5262/01-11/EN 5/21/02, 1:20 PM2
3
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Knowledge
Contents
Preparations
Operations
Caution : Read the pages marked carefully to ensure safe operation.
Introduction ...................................................................................... 2
Before applying power ..................................................... 2
Safety precautions ............................................................. 2
Accessories ............................................................................... 4
CHANNEL SPACE setting (Except for the U.S.A., Canada,
U.K., Europe and Australia)............................................... 4
IMPORTANT SAFEGUARDS .................................................... 5
Special features .............................................................................. 7
Reference ......................................................................................... 7
Maintenance .................................................................................... 8
Discs information ............................................................................ 9
Types of playable discs ........................................................... 9
Unplayable discs ...................................................................... 9
Icons on the DVD discs ............................................................ 9
Region codes ................................................................................. 10
Region codes in the world .................................................... 10
Examples of TV screen display of each video format...... 10
Video formats ................................................................................. 11
Video formats of DVD discs that can be played on this unit......
11
System Connections .............................................................. 12
Loudspeakers .......................................................................... 12
AM loop antenna .................................................................... 13
FM antenna .............................................................................. 13
Connecting to a TV ................................................................. 14
Connecting to a Satellite Tuner ........................................... 14
Connecting to Audio video equipments ............................. 15
Connecting a Camcorder or Video game machine........... 15
Controls and indicators................................................................ 16
Operation of remote control unit ................................................ 17
Let's put out some sound ............................................................. 18
Basic use method ................................................................... 18
Changing the Tone .................................................................. 19
Dimmer ............................................................................................ 20
Receiving broadcast station ....................................................... 21
Storing the broadcast stations (one-by-one presetting) . 22
Using RDS function (for Europe and U.K. only) ................. 23
PTY function (for Europe and U.K. only) ............................. 24
Progressive Scan (for US and Canada only) ............................ 25
Playback of disc ............................................................................ 26
Basic play ................................................................................ 26
Disc playback features .......................................................... 27
Using the On-screen banner display ......................................... 28
Selecting a Title ...................................................................... 29
Selecting a Chapter or Track ................................................ 29
Changing the Audio Language ............................................. 30
Changing the Subtitle Language.......................................... 30
Changing the Camera angle ................................................. 31
Using IntroScan function ...................................................... 31
Using Bookmarks ................................................................... 32
Repeat play .............................................................................. 33
A-B Repeat play ...................................................................... 33
Random play ............................................................................ 34
Program play .................................................................................. 35
Menu playback .............................................................................. 37
Hierarchical structure of VCD menus ................................. 37
Examples of operation keys and indications used during
VCD playback .................................................................... 37
Playback without using the menu playback function (In case
of a P.B.C.-compatible VCD) (To P.B.C. On or Off) .............
38
Enjoying karaoke singing (DVR-6100K only) ............................ 39
Selecting the Audio channel ................................................ 39
Controlling the key of the music (KEY CONTROL) ............ 39
Adjust the ECHO level ............................................................ 40
HIT MASTER function ........................................................... 40
MP3 function .................................................................................. 41
Guidance of MP3 .................................................................... 41
Playing back MP3 ................................................................... 42
Selecting MP3 files ................................................................ 43
MP3 Repeat play ..................................................................... 44
MP3 Random play ................................................................... 44
MP3 Program play .................................................................. 45
Set Up functions ............................................................................ 46
Set up menu ............................................................................. 46
Select Audio Language ......................................................... 47
Select Subtitle Language ...................................................... 47
Select Menu Language .......................................................... 48
Select Rating ........................................................................... 48
Password ................................................................................. 49
TV aspect .................................................................................. 51
Setting up Listen mode................................................................. 52
What are Listen modes? ........................................................ 52
To set the LISTEN mode manually ....................................... 53
Speaker setting ............................................................................. 54
Level setting using a music source..................................... 56
Changing the INPUT MODE ......................................................... 56
Control of a different device with the accessory remote
controller .................................................................................. 57
Register the setup codes for your audio and video.......... 57
Operating other devices ........................................................ 57
Setup code table (except for U.S.A. and Canada) ............ 58
Setup code table (for U.S.A. and Canada only) ................. 59
Keys which can be used to operate connected devices 63
Knowledge ..................................................................................... 64
DVD menu language code list .............................................. 64
In case of difficulty ....................................................................... 65
Specifications................................................................................ 68
*5262/01-11/EN 5/21/02, 1:20 PM3
4
DVR-605/DVR-6100/DVR-6100K (EN)
Preparations
Unpacking
Unpack the unit carefully and make sure that all the accessories are present.
If any accessories are missing, or if the unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to
you directly, notify the shipper immediately.
KENWOOD recommends that you retain the original carton and packing materials in case you need to move or ship the unit in the future.
Keep this manual handy for future reference.
Accessories
Please confirm that the following accessories are present.
FM indoor antenna (1) Loop antenna (1)
Remote control unit (1) Batteries (R6/AA) (2)
*AC plug adaptor (1) * Use to adapt the plug on the
power cord to the shape of
the wall outlet.
(Accessory only for regions
where use is necessary.)
Video cord (1)
System Front, center and surround speakers Subwoofer
DVR-605 KS-306DV (Left speaker, right speaker, SW-06DV
center speaker and surround speakers)
DVR-6100 KSW-6100 (Left speaker, right speaker, center speaker, surround speakers and subwoofer)
DVR-6100K
The space between radio channels has been set to the one
that prevails in the area to which the system is shipped.
However, if the current channel space setting does not
match the setting in the area where the system is to be used,
for instance when you move from area 1 or area 2 shown in
the following table or vice versa, proper reception of AM/FM
broadcasts cannot be expected. In this case, change the
channel space setting in accordance with your area by refer-
ring to the following table.
(Except for the U.S.A., Canada, U.K., Europe and Australia)
CHANNEL
SPACE frequency
Area
1
2
USA, Canada and South
American countries
Other countries
FM : 100 kHz
AM : 10 kHz
FM : 50 kHz
AM : 9 kHz
Setting the CHANNEL SPACE
1Set the POWER key to standby (power off) mode.
2press the STOP key, the ¢ key and the 4 key on
main unit in this order.
Each operate step 2, switches the modes as follows.
1“FM100/AM10 kHz” STEP
2“FM 50 /AM 9 kHz” STEP
CHANNEL SPACE setting
Accessories packed with the main unit
Speaker model names
SCART plug adaptor (1)
(Europe and U.K. only)
Speaker cords (6)
STOP
7
*5262/01-11/EN 5/21/02, 1:20 PM4
5
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Caution : Read this page carefully to ensure
safe operation.
IMPORTANT SAFEGUARDS
6. Temperature – The appliance may not function properly if
used at extremely low, or freezing temperatures. The ideal
ambient temperature is above +5°C (41°F).
7. Heat – The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat. Do not
place a flaming object, such as a candle or lantern, on or near
the appliance.
8. Electric shock – Care should be taken so that objects do not
fall and liquid is not spilled into the enclosure through openings.
If a metal objects, such as a hair pin or a needle, comes into
contact with the inside of this appliance, a dangerous electric
shock may result. For families with children, never permit
children to put anything, especially metal, inside this appliance.
9. Enclosure removal – Never remove the enclosure. If the
internal parts are touched accidentally, a serious electric shock
might occur.
10. Magnetic fields – Keep the appliance away from sources of
magnetic fields such as TV sets, speaker systems, radios,
motorized toys or magnetized objects.
11. Cleaning – Unplug this appliance from the wall outlet before
cleaning. Do not use volatile solvents such as alcohol, paint
thinner, gasoline, or benzine, etc. to clean the cabinet. Use a
clean dry cloth.
12. Accessories – Do not place this appliance on an unstable cart,
stand, tripod, bracket, or table. The appliance may fall, causing
serious injury to a child or adult, and serious damage to the
appliance. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the appliance.
Any mounting of the appliance should follow the manufacturer’s
instructions, and should use a mounting accessory
recommended by the manufacturer. An appliance and cart
combination should be moved with care. Quick stops, excessive
force, and uneven surfaces may cause the appliance and cart
combination to overturn.
Please read all of the safety and operating instructions before
operating this appliance. Adhere to all warnings on the appliance
and in the instruction manual. Follow all the safety and operating
instructions. These safety and operating instructions should be
retained for future reference.
1. Power sources – The appliance should be connected to a
power supply only of the type described in the instruction
manual or as marked on the appliance. If you are not sure of
the type of power supply to your home, consult your appliance
dealer or local power company. For appliances intended to
operate from battery power, or other sources, refer to the
instruction manual.
2. Power-cord protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched by
items placed upon or against them, pay particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
3. CAUTION – Polarization – This appliance may be
equipped with a polarized alternating-current line plug (a plug
having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose
of the polarized plug.
4. Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the appliance
and to protect it from overheating, and these openings must
not be blocked or covered. The appliance should be situated so
that its location or position does not interfere with its proper
ventilation.
To maintain good ventilation, do not put records or a table-cloth
on the appliance. Place the appliance at least 10 cm away from
the walls.
Do not use the appliance on a bed, sofa, rug or similar surface
that may block the ventilation openings. This appliance should
not be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
5. Water and moisture – The appliance shall not be exposed to
dripping and splashing - for example, near a bathtub, washbowl,
kitchen sink, laundry tub, in a wet basement, or near a
swimming pool, etc. Do not place an object containing liquid,
such as a flower vase, on the appliance.
Never pull or stretch
the cord.
*5262/01-11/EN 5/21/02, 1:20 PM5
6
DVR-605/DVR-6100/DVR-6100K (EN)
Preparations
IMPORTANT SAFEGUARDS
13.Lightning – For added protection for this appliance during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the appliance due to lightning and power-line
surges.
14.Abnormal smell – If an abnormal smell or smoke is
detected, immediately turn the power OFF and unplug
the appliance from the wall outlet. Contact your dealer or
nearest service center.
15.Damage requiring service – The appliance should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been
damaged.
B. Objects have fallen, or liquid has been spilled into
the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally
by following the instruction manual. Adjust only those controls
that are covered by the instruction manual as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the appliance to its normal operation.
E. The appliance has been dropped, or the enclosure
damaged.
F. The appliance exhibits a marked change in performance.
16.Servicing – The user should not attempt to service the
appliance beyond that described in the instruction
manual. All other servicing should be referred to qualified
service personnel.
17.Outdoor antenna grounding – If an outside antenna is
connected to the appliance, be sure the antenna system
is grounded so as to provide some protection against
voltage surges and built up static charges. Article 810 of
the National Electrical Code ANSI/NFPA 70, provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements
for the grounding electrode. See Figure.
18.Power lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines
or circuits as contact with them might be fatal.
19.AC outlets – Do not connect other audio equipment
with a power consumption larger than that specified to
the AC outlet on the rear panel. Never connect other
electrical appliances, such as an iron or toaster, to it to
prevent fire or electric shock.
20. Overloading – Do not overload wall outlets, extension cords,
or integral convenience receptacles as this can result in a risk
of fire or electric shock.
21. Attachment – Do not use attachments not recommended by
the appliance manufacturer as they may cause hazards.
22. Replacement parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original parts. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
23. Safety check – Upon completion of any service or repairs to
this appliance, ask the service technician to perform safety
checks to determine that the appliance is in proper operating
condition.
Notes:
1. Item 3 is not required except for grounded or polarized equipment.
2. Item 17 and 18 are not required except for units provided with antenna
terminals.
3. Item 17 complies with UL in the U.S.A.
EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL
ELECTRICAL CODE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUND
CLAMPS
*5262/01-11/EN 5/21/02, 1:20 PM6
7
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Special features
Special features
This document classifies the applications of each feature using the following marks
DVD
: Description of a feature that can be used with DVD.
CD
: Description of a feature that can be used with CD.
VCD
: Description of a feature that can be used with VCD.
Caution on condensation
Condensation (of dew) may occur inside the unit when there is
a great difference in temperature between this unit and the
outside.
This unit may not function properly if condensation occurs. In
this case, leave the unit for a few hours, and restart the opera-
tion after the condensation has dried up.
Be specially cautious against condensation in a fol-
lowing circumstances:
When this unit is carried from one place to another across a large
difference in temperature, when the humidity in the room where
this unit is installed increases, etc.
Reference
Stored contents which are
cleared in at least a week af-
ter power plug is unplugged
from power outlet.
Amplifier section
Last input selection
Volume control value
Surround setting
ACTIVE EQ
Tuner section
Receiving band
Frequency
Preset stations
Tuning mode setting
DVD section
Menu setup
Power status
Memory backup function
WARNING NOTICE:
IN MOST CASES IT IS AN INFRINGEMENT OF COPY-
RIGHT TO MAKE COPIES OF TAPES OR DISCS WITH-
OUT THE PERMISSION OF THE COPYRIGHT OWNERS.
ANYONE WISHING TO COPY COMMERCIALLY AVAIL-
ABLE TAPES OR DISC SHOULD CONTACT THE ME-
CHANICAL COPYRIGHT PROTECTION SOCIETY LIM-
ITED OR THE PERFORMING RIGHTS SOCIETY LIMITED.
Note related to transportation and movement
Before transporting or moving this unit, carry out the
following operations.
1Remove the disc from the unit.
2Press the 6 key.
3Wait a few seconds and turn the unit OFF.
DVD
DVD
DVD
CD
VCD
DVD
DVD
CD
DVD
CD
VCD
Higher video quality than S-VHS video and LaserDisc
Higher audio quality than music CD
Graphical user interface (GUI) compatibility
Versatile DVD playback features
The DVR-605/DVR-6100/6100K offers DTS decoder.
Dolby Pro Logic II decoder.
*5262/01-11/EN 5/21/02, 1:20 PM7
8
DVR-605/DVR-6100/DVR-6100K (EN)
Preparations
Label side
Playing side
Cleaning
If there are fingerprint marks or foreign matter
found on the disc, lightly wipe the disc with a
soft cotton cloth (or similar) from the center of
the disc outwards in a radial manner.
Storage
When a disc is not to be played for a long period
of time, remove it from the player and store it in
its case.
Handling
Hold the discs so that you do not touch
the playing surface.
Disc handling precautions
Disc accessories
The disc accessories (stabilizer, protection sheet, protection ring, etc.) which are marketed for improving the sound quality or
protecting discs as well as the disc cleaner should not be used with this system because they may cause malfunction.
Do not attach paper or tape to either
the playing side or the label side of the
discs.
Sticker
Sticky paste
Never play a cracked or warped disc
During playback, the disc rotates at high speed in the player.
Therefore, to avoid danger, never use a cracked or deformed disc
or a disc repaired with tape or adhesive agent.
Please do not use discs which are not round because they may
cause a malfunction.
Maintenance of the Set
When the front panel, the case, etc. becomes dirty, wipe with a
soft, dry cloth. Do not use thinner, alcohol, etc., as these can
cause discoloration.
In regard to contact cleaners
Do not use contact cleaners because it could cause a malfunction.
Be specially careful not to use contact cleaners containing oil, for
they may deform the plastic component.
Maintenance
CAUTION:
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
In compliance with Federal Regulations, following are reproductions of
labels on, or inside the product relating to laser product safety.
KENWOOD CORPORATION
2967-3, ISHIKAWA-CHO,
HACHIOJI-SHI,
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT CONFORMS TO
DHHS REGULATIONS NO. 21 CFR
1040.10, CHAPTER 1, SUBCHAPTER J.
Location: Back Panel
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or
modification is made.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful interference to radio
communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
– – Reorient or relocate the receiving antenna.
– – Increase the separation between the equipment and receiver.
– – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– – Consult the dealer or an experienced radio / TV technician for help.
For the U.S.A.
Note to CATV sysem inataller
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guide-
lines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of
the building, as close to the point of cable entry as practical.
*5262/01-11/EN 5/21/02, 1:20 PM8
9
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Discs information
Indicates the region code where the disc can be played.
Number of voice languages recorded with the audio function. The number in the icon indicates the number of voice languages.
(Max. 8 languages)
Number of subtitle languages recorded with the subtitle function. The number in the icon indicates the number of subtitle
languages. (Max. 32 languages)
Number of angles provided by the angle function. The number in the icon indicates the number of angles. (Max. 9 angles)
Aspect ratios that can be selected. “LB” stands for Letter Box and “PS” for Pan/Scan. In the example on the left, the 16:9 video
can be converted into letter box video.
9
32
8
16:9 LB
ALL
Icon Description
Icons on the DVD discs
The system using this unit does not only play music from CD but can also play the discs listed below to offer you
high-quality entertainment of video of movies and live concerts.
Unplayable discs
Video + Audio
Audio
Contents
Played sides
Disc size
One side only One side only
Max. 20 min., digital Max. 74 min., digital
One or both One or both
Approx. 41 min.
(1 side, 1 layer)
Approx. 75 min.
(1 side, 2 layers)
Approx. 82 min.
(2 sides, 1 layer)
Approx. 150 min.
(2 sides, 2 layers)
Approx. 133 min.
(1 side, 1 layer)
Approx. 242 min.
(1 side, 2 layers)
Approx. 266 min.
(2 sides, 1 layer)
Approx. 484 min.
(2 sides, 2 layers)
DVD CD (CD-DA)
Logo mark on disc
This player cannot play back any of the following discs.
Playable Disc
Types of playable discs
÷DVD-ROM discs
÷DVD-R/DVD-RAM/DVD-RW discs
÷VSD discs
÷CDV discs (only the audio part can be reproduced.)
÷CD-ROM discs (except MP3 (ISO 9660 level 1 format) disc.)
12cm
8cm
12cm
÷CD-G/CD-EG/CD-EXTRA discs (only the audio can be
reproduced.)
÷Photo CD discs (never attempt to play them.)
÷S-VCD discs
÷CD discs without the CD-DA logo mark may be unplay-
able
Max. 74 min.
DIGITAL VIDEO
COMPACT
VCD
12cm
One side only
8cm
*5262/01-11/EN 5/21/02, 1:21 PM9
10
DVR-605/DVR-6100/DVR-6100K (EN)
Preparations
Every player of this model has a certain region code assigned to it based on the country where the player is used.
When the player is used to play back DVD discs, it can only play the DVD discs carrying the region codes matching
the region code of the player.
The region code for this player is described on the rear panel of the player.
Region codes
Region codes in the world
The DVD players are given a region code according to the country or area it is marketed, as shown in the following
map.
When your TV is compatible only with the
PAL format
With certain discs, the playback pic-
ture may have black spaces above
and below it (as shown on the right).
This is because the disc has been
recorded in the NTSC format. The
screen may be somewhat hard to
see but this is not malfunction.
When your TV is switchable between PAL/
NTSC
Try play a disc. If the picture is black and white or as shown on the right,
stop playback and switch the screen display formats of this unit and the
TV to another format. This will improve the played picture quality.
Examples of TV screen display of each video format
When your TV is compatible only with the
NTSC format
With certain discs, the playback pic-
ture may be cut above and below it
(as shown on the right). This is be-
cause the disc has been recorded in
the PAL format. The screen may be
somewhat hard to see but this is not
malfunction.
1
2
4
1
5
4
5
2
1
2
6
3
*5262/01-11/EN 5/21/02, 1:21 PM10
11
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Major Countries & Areas
Japan, Taiwan, Korea, U.S.A., Canada, Mexico,
Philippines, Chile, etc.
China, U.K., Germany, Australia, New Zealand,
Kuwait, Singapore, etc.
Note
Note
The video signals used to display TV pictures and video
disc pictures are mainly based on two types of signal
formats (PAL and NTSC), which are assigned to each
country or area as shown on the right. As a result, it is
required to select discs according to the video format
used with your TV monitor (in your country or area).
Video formats
TV formats of major countries
Normal video may not be reproduced when a disc recorded with the video format marked * in the above table is played. See “Examples of TV
screen display of each video format” for details. 0
Set the video formats of the DVD discs to be played on this unit as described below.
Check the video format(s) used by your TV monitor.
÷Refer to the operating instructions of your TV monitor for details.
Select DVD discs recorded with the playable video format by referring to the following table.
÷See the region code table on this page for details on districts 1 to 6.
1
2
3
When your TV is switchable between NTSC and PAL,
÷Districts 1, 2-2 and 4-2: Set the TV to NTSC.
÷Districts 2-1, 4-1 and 5: Set the TV to PAL.
÷Districts 2-3, 3 and 6: Set the TV according to each disc to be played.
Video formats of DVD discs that can be played on this unit
TV Format
NTSC
PAL
Area or
Country
Name,
Region
Code
District 1
North
America
District 2-1
Europe
District 2-2
Japan
District 2-3
Middle East
District 3
Southeast
Asia
District 4-1
Oceania
District 4-2
South
America
District 5
Russia
District 6
China
1222
3
4
456
Restrictions due to difference between discs
Some DVD discs can be played only in certain playback modes according to the intentions of the software
producers. As this player plays discs according to their intentions, some functions may not work as
intended by you. Please be sure to read the instructions provided with each disc. When an inhibition icon
is displayed on the TV screen connected to the player, it indicates that the disc being played is under the
restriction as described above.
Inhibition icon
Region code table
Your TV
format
NTSC only
PAL only
NTSC/PAL
switchable
Playable Disc Formats
District 1
NTSC
NTSC*
NTSC
District 2-1
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 2-2
NTSC
NTSC*
NTSC
District 2-3
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 3
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 4-1
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 4-2
NTSC
NTSC*
NTSC
District 5
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
District 6
NTSC
PAL*
NTSC*
PAL
NTSC
PAL
*5262/01-11/EN 5/21/02, 1:21 PM11
12
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
–+
12
Speaker
Front right
Center
Front left
Surround right
Subwoofer
Surround left
Color of the speaker terminal
panel on the main unit
Red
Green
White
Gray
Purple
Blue
System Connections
Caution:
Do not plug in the power lead until all connec-
tions are completed.
Make connections as shown below.
When connecting the related system components, refer also
to the instruction manuals of the related components.
Caution
Be sure to adhere followings. Or proper ventilation will be blocked causing damage or
fire hazard.
÷Do not place any objects impairing heat radiation onto the top of unit.
÷Leave a space around the unit (from the largest outside dimension including pro-
jection) equal or greater than, shown below.
Top panel : 50 cm Side panel : 10 cm Back panel : 10 cm
Malfunction of microcomputer
If operation is not possible or erroneous
display appears even though all connec-
tions have been made properly, reset the
microcomputer referring to “In case of
difficulty”. ˇ
Caution : Read this page carefully to ensure
safe operation.
Loudspeakers
Front
speaker
R
Subwoofer
Surround
speaker
R
White
tube
Black tube
Color tube
Speaker terminal
Upper side mark
Front
speaker
L
Surround
speaker
L
Center speaker
Excessive insertion of the cable can
cause defective contact.
Note
Note
The figure shows an example for the speakers for DVR-605.
Connect the speaker cable terminals
to the terminals with the same color
at the speaker terminal panel on the
main unit. Connect matching the
color of the speaker terminal (+ side)
and the color of the speaker cable
tube.
Speakers for DVR-6100/6100K
The power in this equipment will not be completely cut
off from the AC wall outlet when the main switch is
turned OFF.
*5262/12-20/EN 02.6.18, 3:11 PM12
13
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
System Connections
AM loop antenna
FM antenna
AM loop antenna connection
The supplied antenna is
for indoor use. Place it as
far as possible from the
main system, TV set,
speaker cords and power
cord, and set it to a direc-
tion which provides the
best reception.
FM indoor antenna connection
The accessory antenna is for
temporary indoor use only.
For stable signal reception
we recommend using an out-
door antenna. Remove the
indoor antenna if you con-
nect one outdoors.
1Connect to the antenna terminal.
2Locate the position providing good
reception condition.
3Fix the antenna.
FM outdoor antenna
(commercially available)
Lead the 75 Ω coaxial
cable connected to the
FM outdoor antenna
into the room and con-
nect it to the FM 75 Ω
terminal.
Caution : Read this page carefully to ensure safe operation.
White
*5262/12-20/EN 5/21/02, 1:32 PM13
14
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Connecting to a TV
Connecting to a Satellite Tuner
C
R
C
B
COMPONENT Video cord (except for Europe and U.K)
*COMPOSITE Video cord (accessory)
S-Video cord
COAXIAL cable
Audio cord
COMPOSITE
video cord
Depending on the input switching, the output from the MONITOR OUT terminal will be one of
the following signals. Please note that a different signal type will not be put out.
S-VIDEO terminal : S-video signals from the internal DVD player.
VIDEO terminal : Composite video signal connected to the (VIDEO) VCR IN, the (VIDEO) SAT/
CABLE IN, or the FRONT AUX VIDEO terminal.
COMPONENT connection corresponds only to some areas.
When the TV has a COMPONENT terminal, the DVD image will be played
back with higher picture quality in case of COMPONENT connection.
Connect the S-video or the COMPOSITE video cable also in this case.
If your TV has a progressive scan feature ∞
Note
Note
*For Europe and U.K. only
If your TV set has a SCART terminal,
connect the accessory SCART plug to the
SCART terminal of the TV and connect
the COMPOSITE video cord.
TV
Satellite tuner
System Connections
*5262/12-20/EN 5/21/02, 1:32 PM14
15
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
Connecting to Audio video equipments
OPTICAL cable
Audio cords
COMPOSITE video cord
COMPOSITE video cord
Connecting a Camcorder or Video game machine
PHONES
(OPTICAL)
VIDEO AUDIO
MENU
STOP PLAY/PAUSE
INPUT
76
ON SCREEN
ACTIVE EQ
SELECT/
ENTER
TOP MENU/BAND
LR
FRONT AUX
DIGITAL
OPTICAL cable
Audio cord
COMPOSITE video cord
In case of digital recording
with an MD recorder or a CD
recorder
Analog recording of DTS-encoded
discs is not possible.
Note
Note
Video game machine
Camcorder
When DIGITAL OUT signal is PCM format
System Connections
This unit's digital out does
not convert DVD bit stream
data to PCM format. When
playing Dolby Digital or DTS
format DVDs, bit stream data
is output from the digital out.
To make digital recordings,
play PCM format discs.
Note
Note
*5262/12-20/EN 02.6.18, 3:11 PM15
16
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
MENU
STOP PLAY/PAUSE
INPUT
76
0
ON SCREENVOLUME
OPEN/CLOSE
POWER
-ON/–OFFSTANDBY
ACTIVE EQ
ENTER
MIC LEVEL
CS II
TOP MENU/BAND
DSP
PRO LOGIC IIDOLBY DIGITAL
DTS
PHONES
(OPTICAL)
VIDEO AUDIO LR
FRONT AUX
DIGITAL
1
2
7
0
@
#
%
& $^*(
4
8
!
9
653
PARENTAL LOCK
indicator
PROG. (Program)
indicator
PLAY/PAUSE indicator
IN/OUT status indicator
L : Left speaker
C : Center speaker
R : Right speaker
LFE : Low Frequency Effect
SW : Subwoofer
LS : Left surround speaker
S : Surround speakers
RS : Right surround speaker
Display
1POWER switch *
2STANDBY indicator ^
3LISTEN MODE indicators E
4MIC jack and LEVEL control ·
(DVR-6100K only)
54, ¢ (Skip) keys ¡¶
6FRONT AUX jacks %
7PHONES jack *
8Door
9TOP MENU/BAND key ¡°
0INPUT key *
!Cursor Up (5), Down (∞),
Left (2) and Right (3) keys
ENTER key •ey
@6 (PLAY/PAUSE) key §
#7 (STOP) key §
$MENU key y
%ON SCREEN key ∞•
^ACTIVE EQ key (
&VOLUME CONTROL knob *
*0 (OPEN/CLOSE) key §
(Disc tray §
DVD indicator
VCD indicator
CD indicator
MP3 indicator
INTRO SCAN indicator
RANDOM indicator
REPEAT indicators
REPEAT
1 REPEAT
ALL REPEAT
A-B REPEAT
Character
information
display section
Controls and indicators
RDS indicator (only
for Europe and U.K.)
PBC indicator
TITLE indicator
TRACK indicator
CHAPTER indicator
AUTO indicator
TUNED indicator
ST (Stereo) indicator
STANDBY
The STANDBY indicator lights when the power cable is plugged into an outlet and the POWER switch is set to ON. While the
standby indicator is lit, a small amount of power is supplied to the system to back up the memory. When the POWER key on the
remote control unit is pressed in STANDBY status, the STANDBY indicator goes out and the main unit reaches operation status.
When the POWER switch is set to OFF in operation status, the unit will return to operation status when the POWER switch is set to
ON again. When the POWER switch is set to OFF in STANDBY status, the unit will return to STANDBY status when the POWER
switch is set to ON again.
ACTIVE EQ
indicator
*5262/12-20/EN 02.6.18, 3:11 PM16
17
Preparations
DVR-605/DVR-6100/DVR-6100K (EN)
The keys on the remote control unit with the same names as on the
main unit have the same function as the keys on the main unit.
1SOURCE key U´
2DISPLAY key )
3INPUT SELECTOR keys *
4TV key ´
5Numeric keys (0 - 9, +10,+100)
™¶´
PGM key fi
CLEAR key t
6MUTE key *
7VOLUME keys *
8TOP MENU key §
/P.B.C. key °
9Cursor Up (5), Down (∞),
Left (2) and Right (3) keys
ENTER key •ey
0RETURN key y
!4/ ¢(Skip) keys
P.CALL keys ¡¶
@¶ REC (record) key ´
S.TITLE key º
#1/ ¡(Search) keys ¶
/ TUNE keys ¡
/ TV. VOL. keys ´
$Speaker select keys Y
%Listen mode key
()E
^Active EQ./SOUND key (
SETUP key R
&POWER key &
Loading batteries
2 Insert batteries. 3 Close the cover.1 Remove the cover.
÷Insert two R6 (“AA”) batteries follow-
ing the polarity indications.
Operation
Insert the power plug into a power outlet, press the POWER
switch of the main unit to ON, then press the POWER key
on the remote control.
÷When pressing more than one remote control keys successively,
press the keys securely by leaving an interval of 1 second or more
between pressing of keys.
Operating range (approx.)
Remote sensor
1. The provided batteries are intended for use in operation checking, and their service life may be short.
2. When the remote controllable distance becomes short, replace both of the batteries with new ones.
3. If direct sunlight or the light of a high- frequency fluorescent lamp (inverter type, etc.) is incident to the remote sensor, malfunction
may occur. In such a case, change the installation position to avoid malfunction.
Model : RC-R0624 (for USA and Canada), RC-R0624E (for Europe and U.K.), RC-R0624K (for other countries)
Infrared ray system
Operation of remote control unit
Notes
Notes
SAT
SOURCE
TV FRONT
AUX
CLEAR
321
654
987
+10
+
–
+
–
0+100
PGM
CABLEVCR
SET
AUDIO
MUTE
REPEAT
A-B
TV INPUT
ENTER
VOLUME CH.
TOP MENU/P.B.C. MENU/PTY
ON SCREEN
RDS
¢34
87¶
REC
RETURN
P.CALL
TUNE/TV VOL.
STEPSLOW
¡1
5
REAR
CENTER
FRONT
∞
SW
SETUP
S.TITLE AUTO/MONO PRESET
ECHO
–+
TRIM
SOUND
Active EQ./Listen mode
INPUT MODE
RANDOM
TUNER
BAND
DVD/CD
DISPLAY
POWER
1
2&
*
(
)
¡
™
¢
£
3
4
5
6
8
7
9
0
!∞
¶
•
ª
º
@
$
%
^
#
§
*INPUT MODE / RANDOM key
Y›
(SET / AUDIO key ´·
)CH. UP / DOWN keys ´
/ REPEAT A-B keys ‹
¡TV INPUT key ´
™MENU key y
PTY key (Europe and U.K. only)
¢
£3 (play) key §
¢ON SCREEN key •
RDS key (Europe and U.K. only)
£
∞8 (pause) key §
PRESET key ™
§7 (stop) key §
AUTO/MONO key ¡
¶SLOW key
(DVR-605/6100) ¶
SLOW / STEP key
(DVR-6100K) ¶
•STEP key
(DVR-605/6100) ¶
SHIFT key
(DVR-6100K) ¶·
ªKaraoke keys (DVR-6100K only)
ECHO keys ‚
Key Control keys ·
ºTRIM / Up (5), Down (∞) keys
()R
30º
30º
6m
*5262/12-20/EN 5/21/02, 1:33 PM17
18
DVR-605/DVR-6100/DVR-6100K (EN)
Operations
Let's put out some sound
Preparation
÷set the POWER switch to the ON ( ) position.
POWER
-ON/–OFF
POWER
INPUT
SELECTOR
VOLUME CONTROL
POWER
VOLUME MUTE
INPUT
PHONES
Basic use method
Selecting the desired input
Volume adjustment
1
2
Muting the sound temporarily
Listening through headphone
REMOTE
REMOTE
MAIN UNIT
To decrease To increase To decrease
To increase
Remote control unit only
÷Press again to resume the original volume.
÷The sound muting is also cancelled when the volume is con-
trolled.
÷Press the MUTE key.
Insert the headphone plug into the PHONES jack.
÷The sounds from all speakers are cut off.
÷When one of the keys on the left is pressed while STANDBY
mode, the power will be switched on automatically and the input
will be selected.
÷The power will be switched on and the respective operation will
be performed also when the OPEN/CLOSE key, the PLAY/
PAUSE key or the BAND key on the main unit is pressed during
STANDBY mode.
÷When a disc is set in the disc tray and the DVD CD key is pressed,
disc playback will start automatically.
In case of operation with the remote control unit, first select
the input or device to be operated with the INPUT SELEC-
TOR keys then perform the desired operation.
The present mode of the remote control unit may not
coincide with the equipment to be operated.
VOLUME
This unit offers various surround modes, but it switches
automatically to stereo mode when headphones are connected.
To open the door, pull the lower part on the right side of the
main unit.
SAT
CABLEVCR
TUNER
BAND
DVD/CD
FRONT
AUX
INPUT
+
–
VOLUME
MUTE
PHONES
1Tuner (frequency display)
2VCR (VCR → ANALOG → VCR)
3SAT/CABLE (SAT/CABLE → AUTO → SAT/CABLE)
4FRONT AUX (FRONT → OPTICAL → FRONT)
5DVD/CD
Switching is done as follows when the INPUT key of the
main unit is pressed. (The parenthesized part shows an
operating example.)
The input mode can be switched with SAT/CABLE
and FRONT AUX.
Refer to “Changing the INPUT MODE” Y
Note
Note
MAIN UNIT
MAIN UNIT
Normally "MAX" is displayed when the volume settings set to
the maximum value.
If you have adjusted the speaker level above 0db with the
TRIM key (R), "MAX" will not be displayed.
÷When using the remote to select SAT or CABLE;
SAT (SAT → AUTO → SAT)
CABLE (CABLE → AUTO → CABLE)
*5262/12-20/EN 02.6.18, 3:11 PM18
19
DVR-605/DVR-6100/DVR-6100K (EN)
Operations
Changing the Tone
Let's put out some sound
This unit is equipped with various preset equalizers, so that various sounds can be enjoyed. In addition, it has an ACTIVE EQ.
function for one-touch equalization.
Selecting the DSP mode
REMOTE
Press the Listen mode key repeatedly
Listen mode
Each press switches the mode
(At the time of music CD)
1DOLBY PL II MOVIE
2DOLBY PL II MUSIC
3DOLBY PRO LOGIC
4CS II MUSIC
5CS II CINEMA
6CS II MONO
7ARENA
8JAZZ CLUB
9THEATER
0STADIUM
-DISCO
=STEREO
Five different sounds are preset in DSP mode. Please select the type you like.
DSP mode can be selected only at the time of a PCM source (normal music CD, MP3 file, etc.).
DSP modes
DSP
Lit
PRO LOGIC II
modes
CS II modes
ACTIVE EQ.
1CINEMA (ACTIVE EQ. lit)
2MUSIC (ACTIVE EQ. lit)
3OFF
REMOTE
Each press switches the ACTIVE EQ.
Press the ACTIVE EQ key repeatedly
Selecting the NIGHT (MID NIGHT) mode. (Dolby Digital only)
REMOTE
Press the SOUND key.
Any time you don’t want to experience the loud and soft volume extremes of recorded sound (for example, late at night), use
NIGHT function to reduce volume extremes.
1
Press the TRIM (
5
/
∞
) key.
2
5
∞
TRIM
Displayed NIGHT OFF (or NIGHT ON).
Each press switches the mode
1NIGHT ON
2NIGHT OFF
CS II
Lit
Lit
PRO LOGIC II
MAIN UNIT
ACTIVE EQ
SOUND
Active EQ./
Lit
÷In some cases, the unit may not enter the ACTIVE EQ mode
by pressing the ACTIVE EQ key once. In this case, press the
key one more time.
SOUND
Active EQ./
5
∞
TRIM
*5262/12-20/EN 5/21/02, 1:33 PM19
20
DVR-605/DVR-6100/DVR-6100K (EN)
Operations
Press the Listen mode key
Let's put out some sound
TREBLE CONTROL (Normal music CD , VCD and tuner only)
REMOTE
Each press switch the TRBL level
÷The treble level can be adjusted between +10 and -10.
2
Press the SOUND key
3
SOUND
Active EQ./
Select treble level
5
∞
TRIM
To decrease
To increase
TRBL is displayed.
1
Listen mode
Set to STEREO mode. (The TREBLE CONTROL can be
adjusted only STEREO mode)
Operation is not possible with DOLBY DIGITAL and DTS
source.
Dimmer
The brightness of the display can be changed in 3 levels. Adjust the brightness as you like by pressing the DISPLAY key.
Press the DISPLAY key for more than
2 seconds
REMOTE
DISPLAY
*5262/12-20/EN 5/21/02, 1:33 PM20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI