QUICK INSTALLATION GUIDE
3
2
1. Product Description [EN]
The anywAiR device is an external module capable of connecting your Air
Conditioning units into your Wi-Fi network in order to provide global connectivity
and remote control applications through a friendly user interface.
Packaging content (Figure 1):
(a) anywAiR Device (b) 3 rubber feet (c) Quick install guide
(d) Power supply + 4 plugs (EU, UK, US, AU) (e) Additional cable
* The AnywAiR device requires a (5VDC 0,25 A) NEC Class 2 or Limited Power Source (LPS) and SELV rated
powersupply as the one provided.
2. Installation overview
The anywAiR device can be installed on a wall mounted position (Figure 2) or
in a desktop position (Figure3). Socket-outlet shall be near the equipment and
shall be accessible.
CAUTION: To ensure regulatory compliance, use only the provided power
supply. Keep in mind that some furniture and materials (carpets, curtains, glass,
metal…) may aect on the IR communication.
3. Wi-Fi conguration
Follow the instructions below for Wi-Fi conguration:
1. Download the myanywAir application from Google Play or App Store.
2. Visit the wireless settings section of your wireless device (smartphone or tablet)
and connect to the network generated by your device (DEVICE_xxxxxx).
3. Open the app and click on the add device Button located in the left button
side of the main screen.
4. Once the LED of the device is steady green, click the Start button of the app.
5. Select “Automatic”.
6. Select the wireless network the device will be connected to.
7. Introduce the wireless network password and press connect.
8. The device will go through a led blinking process and it will nish with
the LED o. If this is not the case please complete the process again. If
problem persist, contact our support team.
For more detailed Wi-FI conguration information, please refer to:
https://www.fujitsugeneral.com.au/anywair/manuals/Quick_Wireless_Cong.pdf
Wi-FI specications
QUICK INSTALLATION GUIDE
More information at https://www.fujitsugeneral.com.au/anywair/manuals
5
4
CERTIFICATIONS
FCC Interference Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation of this device.
Contains FCC ID: 2AC7Z-ESPWROOM02
RF Exposure Warning Notice:
• This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency
(RF) Exposure rules.
• This equipment has very low levels of RF energy that is deemed to comply without
maximum permissive exposure evaluation (MPE).
• This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter.
Caution:
• To assure continued compliance, follow the attached installation instructions. Any
changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
• This transmitter external antenna must be installed and operated keeping at least
20 cm (7 7/8 inch).
RSS-102, Issue 5
Device compliant with the standard:
RSS-102, Issue 5
Safety Code 6: Health Canada’s Radiofrequency Exposure
Guidelines
IEC 62368-1:2014 (Second Edition)
Report Number .............................. : NC28090-A6001-CB-1
Ratings .................................... : class III (ES1, PS1) device, rating is optional: 5Vdc 250mA
Summary of compliance with National Dierences: AU,NZ, EU Group Dierences, US,CA
Radiocommunications (Electromagnetic Compatibility) Standard 2017, refer RadioMotive S.r.l.
EN 55032:2015 + AC:2016 test report No. 0203a1_18_EMCTR-0 dated 3 August 2018.
Radiocommunications (Short Range Devices) Standard 2014, refer RadioMotive S.r.l.
EN 300 328 v2.1.1 test report No. 0203b_18_RADIOTR-1 dated 2 August 2018.
Radiocommunications (Electromagnetic Radiation – Human Exposure) Standard 2014, refer
RadioMotive S.r.l. EN 62311:2008 test report No. 0203c_18_EMFTR-1 dated 2 August 2018.
QUICK INSTALLATION GUIDE
QUICK INSTALLATION GUIDE
4. IR conguration (learning mode)
IMPORTANT: Before starting the IR conguration process, please check the
compatibility list at https://www.fujitsugeneral.com.au/anywair/manuals and make
sure that you have the AnywAiR device already connected to the Internet.
1. Push the Button for 3 seconds. The LED will turn into white steady.
2. Pick up the IR wireless controller and push the On/O button pointing to the
anywAiR device.
• If process is not OK, the anywAiR device LED will be blinking in Red.
Repeat the process from step 1 and check our compatibility list or visit
https://www.fujitsugeneral.com.au/anywair/manuals for more details.
• If process is OK, the IntesisHome device LED will be blinking in Green.
5. Device registration
Follow bellow instructions to register your device:
1. Download myanywAiR app from Google Play or the App Store and install it.
2. Create an account (in case you don’t have it yet).
3. Visit the settings/device/ section and click on add device.
4. Introduce the registration code (25 digit code on the manual sticker).
6. Safety Precautions
To prevent personal injury, or property damage, please read this section
carefully before using this product, and be sure to comply the following safety
precautions.
Incorrect operation due to failure to follow the instructions may cause harm or
damage to you or to the device.
• Do not repair, disassemble or remodel this product.
• Do not operate with wet hands.
• Do not install this product outdoors or exposed to direct solar radiation,
water, high relative humidity or dust.
• In case of wall mount, x it rmly on a not vibrating surface.
• Use the provided power supply for product correct functioning.
• In the event of malfunction such as burning smell, immediately disconnect
the device from the power plug. Then consult authorized service personnel.
You can nd detailed information about all the installation and conguration
process at https://www.fujitsugeneral.com.au/anywair/manuals
7
6
WARRANTY
Certain legislation, including the Australian Consumer Law (ACL), may imply warranties or
conditions or impose guarantees or obligations on Fujitsu which cannot be excluded, restricted
or modied or cannot be excluded, restricted or modied except to a limited extent (Owner’s
Statutory Rights).
THE RIGHTS GIVEN BY THIS 2 YEAR WARRANTY ARE IN ADDITION TO ANY RIGHTS AND
REMEDIES THAT THE OWNER MAY HAVE UNDER THE AUSTRALIAN CONSUMER LAW AND
OTHER LAWS. THIS WARRANTY REPLACES ALL OTHER WARRANTIES PROVIDED WITH
THE AIR CONDITIONING PRODUCT.
The Wi Adaptor product listed on the back of this manual is warranted by Fujitsu General (AUST.)
Pty Limited (ACN 001 229 554) against defects in design, materials and workmanship for a period
of 2 years from the date the adaptor was commissioned by Fujitsu General (AUST.) Pty Limited
or approved installer.
Adaptor defects covered by this Warranty will be repaired or replaced at the discretion of Fujitsu
General (AUST.) Pty Limited (subject to the owner’s rights under the ACL with respect to major
failures) without cost to the Owner for replacement parts or equipment. The repair or replacement
shall be performed during normal business hours by Fujitsu General (AUST.) Pty Limited or a
repair agent authorised by Fujitsu General (AUST.) Pty Limited.
If your Fujitsu General WiFi Adaptor is repaired or replaced under this Warranty, it will be
warranted in accordance with the provisions of this Warranty for the remainder of the original
warranty period or 6 months from the completion of the repair or replacement of the parts or air
conditioner, whichever is the greater.
Except where inconsistent with the Owner’s Statutory Rights and the rights given by this Warranty,
all other warranties and all liability of Fujitsu General (AUST.) Pty Limited for any loss or damage
direct and consequential is expressly excluded.
To claim under this warranty Owner should contact Fujitsu General (AUST.) Pty Limited (www.
fujitsugeneral.com.au) or their designated service agent. Alternatively, Owner can send a claim to
Fujitsu General (AUST.) Pty Limited at the address on the back of this manual.
Owner will be responsible for the following costs associated with making the warranty claim:
• All costs associated with travel outside of the area normally serviced by Fujitsu General (AUST.)
Pty Limited or any repair agent authorised by Fujitsu General (AUST.) Pty Limited;
• Freight charges including insurance; and
• All costs related to gaining access to unsafe (eg high) or restricted locations.
The Owner will be liable for all costs incurred by Fujitsu if the problem is not covered by the
provisions of this Warranty or the Owner’s Statutory Rights.
This Warranty DOES NOT cover:
a) Faults or substandard performance resulting from operation at conditions outside the operating
conditions as specied in the Fujitsu General technical or sales literature applicable to the Wi
Adaptor.
b) Faults or substandard performance resulting from misapplication of the Wi Adaptor.
c) Faults or substandard performance resulting from operation of the Wi Adaptor when used for
applications other than the climatic comfort of humans.
d) Faults or substandard performance resulting from incorrect or poor installation.
e) All costs related to gaining access when installed in unsafe (eg high) or restricted locations.
f) Faults or substandard performance caused by any product or part other than supplied by Fujitsu
General (AUST.) Pty Limited.
g) Costs associated with travel outside of the area normally serviced by Fujitsu General (AUST.)
Pty Limited or any repair agent authorised by Fujitsu General (AUST.) Pty Limited or freight
charges including insurance.
h) Faults or substandard performance caused to the WiFi Adaptor by faulty or incorrect
external electrical wiring, incorrect power supply, voltage uctuations, over voltage transients or
electromagnetic interference not originating within the air conditioner.
i) Faults or substandard performance caused by vermin, blocked lters, misuse, storm, ood, re,
earthquake, negligence, vandalism, Acts of God, war, foreign matter entering the air conditioner
(eg leaf matter, dirt and moisture) or any other outside agency.
j) Faults caused by internet connectivity issues such as poor connections, internet drop outs or
router issues.
Where this Warranty does not apply, the Owner’s rights are limited to the Owner’s non-excludable
Statutory Rights.
Owner’s Responsibility
Where our service personnel are unable to identify any fault in the product, Fujitsu General
(AUST.) Pty Limited may require you to provide proof that the Wi Adaptor is defective.
Limitation of Owner’s Statutory Rights
In respect of any goods supplied under the contract which are not acquired by a consumer, as
that term is dened in the ACL, all liability of Fujitsu General (AUST.) Pty Limited for any loss or
damage, direct and consequential, not covered by this Warranty is expressly excluded.
In respect of any goods supplied under the contract which are acquired by a consumer, but are not
of a kind ordinarily acquired for personal, domestic or household use or consumption, unless the
Owner establishes the following limitation of liability would not be fair and reasonable, the liability
of Fujitsu General (AUST.) Pty Limited for any defect of design, materials or workmanship will be
limited to any of the following as determined by Fujitsu General (AUST.) Pty Limited:
a) replacing the Wi Adaptor or supplying an equivalent adaptor;
b) repairing the Wi Adaptor;
c) paying the cost of replacing the Wi Adaptor or supplying an equivalent adaptor;
d) paying the cost of having the Wi Adaptor repaired.
Your statutory rights
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any
other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the failure does not amount to a
major failure.
To the extent our goods are not of a kind ordinarily acquired for personal, domestic or household
use or consumption, then we may limit our liability as we have done so above to repair or
replacement of goods or the payment of the cost of repairing or replacing goods, or supplying
services again or payment for the cost of supplying services again, in accordance with section
64A of the Australian Consumer Law.
Personal Information Collection Notice
To receive the benet of this warranty, you will need to provide certain personal information such
as your name and address to Fujitsu General (Aust) Pty Ltd and ABN 55 001 229 554.
We collect this personal information for the purposes of commissioning a service agent to attend
to your warranty issue. If you do not provide us with the relevant information, you will not be able
to benet from this warranty.
We will handle all personal information provided to us in accordance with all applicable privacy
laws. If you would like further details regarding how we handle your personal information or how
you can access or correct this personal information, please review our privacy policy accessible
here www.fujitsugeneral.com.au/help-centre/privacy-policy or contact us on the details provided
below.
Fujitsu General (Aust) Pty Ltd ABN 55 001 229 554
T. 1300 822 201
8
FUJITSU GENERAL AUSTRALIA - 1 Telopea Place, Eastern Creek NSW 2766
Ltd ABN 55 001 229 554 - a subsidiari of FUJITSU GENERAL LIMITED
Document Review v.1.0
/