Dakota Micro OverView DMOV-7M-C2 User manual

Type
User manual

Dakota Micro OverView DMOV-7M-C2 is an advanced 7-inch, high-resolution TFT LCD monitor designed for use in rear-view monitoring systems. It features a wide voltage input range of 11-32V, making it compatible with most vehicles. The monitor has three video channel inputs, allowing you to connect up to three cameras. It also supports manual or automatic image switching modes, giving you the flexibility to choose how the cameras are displayed. With its forward/mirror image selection, you can easily adjust the image to suit your preferences.

Dakota Micro OverView DMOV-7M-C2 is an advanced 7-inch, high-resolution TFT LCD monitor designed for use in rear-view monitoring systems. It features a wide voltage input range of 11-32V, making it compatible with most vehicles. The monitor has three video channel inputs, allowing you to connect up to three cameras. It also supports manual or automatic image switching modes, giving you the flexibility to choose how the cameras are displayed. With its forward/mirror image selection, you can easily adjust the image to suit your preferences.

DakotaMicro,Inc.
8659148thAve.SE
Cayuga,ND58013
www.dakotamicro.com
Author:CNR Title:UserManDMOV‐7M‐C2Rev:10/18/17
RearViewMonitoringSystem
UserManual
PartNumber:DMOV‐7M‐C2
www.dakotamicro.com
TROUBLESHOOTING
Problem Possible Causes
No picture, no sound
Improper connection with 12v power adapter.
Use of unauthorized power supply
Monitor is in OFF position
No picture
Check whether AV cable is securely plugged in
No sound
Check whether audio connector is secure
Check whether the sound volume is turned off or down
Dark picture
Ensure that bright and contrast settings are properly
adjusted
Ensure monitor is warm enough
No color
Ensure color settings are properly adjusted in menu
Upside down or lateral
inverted picture
Check horizontal/vertical adjustment on remote
Event Triggers not
activating (i.e. No
picture during triggered
event)
Event trigger is not securely connected
Remote Controller Fault
Battery may be dead or improperly installed:
replacement battery Model:CR2025,3V
Remote controller is not pointed in the direction of the
receiving sensor on monitor
Too far away or improper angle: The maximum effective
distance between the remote controller and the receiving
sensor is 15 feet and the angle is 30 degrees.
Obstacle: Move any obstacles out of the path
LIMITEDWARRANTY
7inchLEDbacklit,highresolutionTFTLCD
Widevoltageinput:11‐32V
3VideoChannelInputs
Manualorautomaticimageswitchingmodes
Forward/Mirrorimageselection
EventTriggersprovidedforall4cameras.Camerascanbetriggeredforeventssuchas
backinguporapplyingthebrakes
Powerisprovidedonlytotheactivecamera,prolongingthelifeofthecameras
AVinputandoutputjacksprovided
AutoON/OFFLEDsensorautomaticallytriggersnightvisionwhenrequired
Includescreditcardstyleremotecontrol
Backlitcontrolbuttonsenableeasymenunavigationinalllightingconditions
Pleasereadentiremanualbeforeusingourproducts
BeforeyoupoweryourrearOverViewsystem,ensurethatallcablesareproperly
connectedtoavoiddamagetothesystem
MonitorISNOTWATERPROOF,pleasedonotplacethemonitoroutdoors
Ensurethatallcablesareroutedasufficientdistancefromhightemperatureareasand
rotaryobjects
Toensureproperheatdispersal,ensurethatventholesinmonitorremainclear
Donotopenthemonitororcameracasing,doingsowillvoidthewarranty
DONOTwatchDVDsetc.whiledriving
Pleasedonotusecausticchemicalstowipethecameraand/ormonitor
Subjecttothedisclaimer,limitationsandotherdirectionsstatedhereafter,DakotaMicro,Inc.warrantsthat
theProductwillbefreefromdefectsinmaterialandworkmanshipforperiodsasstatedhereafterfromthe
dateoforiginalpurchase.THISWARRANTYISEXPRESSLYMADEINLIEUOFANYANDALLOTHER
WARRANTIES,EXPRESSORIMPLIED,INCLUDINGTHEIMPLIEDWARRANTIESOFMERCHANTABILITYOR
FITNESS.THEEXCLUSIVEREMEDYOFTHEBUYERISLIMITEDTOREPAIRORREPLACEMENTOFTHEPRODUCT.
EXCEPTASSTATEDINTHISWARRANTY,DAKOTAMICROSHALLNOTBELIABLEFORANYLOSS,
INCONVENIENCE,ORDAMAGE,INCLUDINGDIRECT,SPECIAL,INCIDENTAL,ORCONSEQUENTIALDAMAGES,
RESULTINGFROMTHEUSEORINABILITYTOUSETHEPRODUCT,WHETHERRESULTINGFROMBREACHOF
WARRANTY,NEGLIGENCE,STRICTLIABILITYOFANYOTHERLEGALTHEORY.Anyoralstatementsor
representationsmadebyanyonewhicharecontrarytooratvariancewiththetermsstatedinthis
LIMITEDWARRANTYarevoid.
DakotaMicrowill,atitsoption,eitherrepairthedefectorreplacethedefectiveProductorpartthereofwithanew
orremanufacturedequivalentatnochargetothepurchaserforpartsorlaborfortheperiodofthree(3)yearsfor
AgCam/EnduraCamcameras,two(2)yearsforAgCam/EnduraCammonitors,quadsandwireless.TwelveMonths
(12) forallOverViewCameras&Monitorsaswellasallothercablesandaccessories.
TheDakotaMicrolimitedwarrantyperiodsoutlinedaboveapplythroughouttheUnitedStatesandCanadaonly.A
one(1)yearmaximumlimitedwarrantyforallProductsappliestoallothergeographiclocationsunlessotherwise
statedinwritingbyDakotaMicro.
Thislimitedwarrantydoesnotapplytoanyissuesconnectedwithappearancethathavenorelationtothe
performanceoftheProductnortoanyProducttheexteriorofwhichhasbeendamagedordefaced,whichhas
beensubjectedtoimpropervoltageorothermisuse,abnormalserviceorhandling,orwhichhasbeenalteredor
modifiedindesignorconstruction.
Inordertoenforcetherightsunderthislimitedwarranty,thepurchasershouldfollowtheprocesssetforthon
page3ofthisPolicy,andprovideproofofpurchasetoDakotaMicro,Inc.Neitherthesalespersonnelof
DakotaMicronoranydealeroranyotherpersonisauthorizedtomakeanywarrantiesotherthanthose
describedherein,ortoextendthedurationofanywarrantiesbeyondthetimeperiodsdescribedherein.
ThewarrantiesdescribedhereinshallbethesoleandexclusivewarrantiesandremediesprovidedbyDakotaMicro.
Correctionofdefects,inthemannerandfortheperiodoftimedescribedherein,shallconstitutecomplete
fulfillmentofallliabilitiesandresponsibilitiesofDakotaMicrotothepurchaserwithrespecttotheProduct,and
shallconstitutefullsatisfactionofallclaims.InnoeventshallDakotaMicrobeliableorinanywayresponsiblefor
anydamagesordefectsintheProductwhichwerecausedbyrepairsorattemptedrepairsperformedbyanyone
otherthanDakotaMicro.
Somestatesdonotallowthelimitationonorexclusionofincidentalorconsequentialdamages,sosaidlimitationmay
notapplytoyou.
Anyactionatlaw,suitinequity,orotherjudicialproceedingfortheenforcementofanyrightprovidedforherein
orotherwise,orwithrespecttoanyclaimthatapurchasermayhaveagainstDakotaMicro,Inc.shallbeinstituted
onlyintheCourtsoftheStateofNorthDakota,eitherinthestatedistrictcourtlocatedinWahpeton,NorthDakota
orinFederalDistrictCourtlocationinFargo,NorthDakota.Withoutregardtoconflictsoflawprinciples,thelawsof
thestateofNorthDakotashallgoverntheinterpretationandenforcementofthetermsofthisLimitedWarranty
andallaspectsoftherelationshipbetweenDakotaMicroandthepurchaser.
Thiswarrantygivesyouspecificlegalrightsandyoumayalsohaveotherrights,whichmayvaryfromstatetostate
WARNINGS
WARNINGS
The OverView camera system is intended for light use and is not intended to be utilized in harsh
conditions such as high vibration, high moisture, and use in or around corrosive substances or
other high impact or corrosive situations. Should a heavy duty camera be required for your
application, an AgCam or EnduraCam camera from Dakota Micro should be utilized and is
warranted for this type of use. Warranty will be void on this system should it be utilized outside of
its recommended applications.
FEATURES
9
2
I. MonitorIntroduction
ConnectionChart

EventTriggerwireCAM1(white*)
①Left/Vol‐ ②Right/Vol+ ③Menu ④Down/CamSelecti
⑤Up/CamSelection ⑥QuadViewModeSwitch ⑦ON/OFF
Power/Video
Harness
Connectorwith
screws
FUSE
1)
Cameras1‐3haveanavailableeventtriggerwire.Camerasareidentifiedas1,2and3
CAM1‐Whiteconnector

CAM2‐Blueconnector

CAM3‐Brownconnector
2)
RegardlessifmonitorisONorOFF,ifpowerisappliedtothetrigger,activatedcamerawillbecome
powered
*EventTriggerwirecolorsaresubjecttochangewithoutnoticeandmayvaryslightlyfromthe
colorsindicatedabove.
Monitor
Included Components
Monitor w/ bracket
Monitor remote control
Power/Video harness
x2 Camera(s) w/ bracket
x2 40ft power/video cables
12v lighter adaptor
Screen Size
7” (16:9) digital panel
Overall Size
185mm(W)x124mm(H)x48(D) without mounting
bracket
Weight 400g
Power Input AC 10.5-16.9V, 1,200 ma (2 cameras)
Color System
NTSC/PAL auto switch
Operating Temp -4°F~122°F (-20°C~50°C)
Brightness
400cd/m
2
Resolution
800(RGB) x 480
Contrast
500:1
Number of Camera Inputs
4
4
7
X. ButtonFunction
MUTE
PressMutetoturnsoundofftoresumevolume,pressMuteagainorpressVOL+.
POWER
PowersmonitorONandOFF.
CHbutton(up/down)
ToselectCH(Up)orCH(Down)
VOL‐/+
a. Adjustvolumeofmonitor.
b. Adjustbrightness,contrast,etc.
c. Toactivateotherfunctions,suchas,mirror/normalimageswitch,delaytimeadjustment,etc.
MENU
Displaysmonitormainmenu.
MODE
Usercanusethiskeytoselectfourmodes:standardcolor,softcolor,richcolorandbright.
CALL
PressthisbuttonistodisplaycurrentlydisplayedAVchannel.
TIMR
Timesetupofsleepoff,itisusedtosetthetimeoffwithin120minutes.
C/E/P
Languageselection:ChoiceofChineseorEnglish.
AC1/AV2/AV3
Pressthisbuttontotogglebetweenthe3videoinputs.
VI. MonitorOperation

Monitor
Remote Control
VII.MonitorMenuInstructions
a. Picture
Defaultvaluesformonitorbrightness,contrast
andsaturationis50.NTSChuedefaultissetto0.
Brightness,contrastandsaturationvaluescanbe
adjustedfrom0‐100.Huevaluecanbeadjusted
between‐50to+50.
b. ChannelReverseSetup
Defaultvaluesforpicturemodeisnormal(N‐LR).
Eachchannelhas4viewingmodesavailable:
LR(normalImage)
M‐LR(mirrorimage)
M‐UD(mirrorupsidedownimage)
N‐UD(normalupsidedownimage)
c. ReversePrioritySetup
ThedefaultreversechannelisCAM1.Default
priorityissetto:CAM1>CAM2>CAM3.Pressthe
arrowstochangeprioritybetweenCAM1and
CAM2.
WhenCAM2hasreversepriority,orderissetto:
CAM2>CAM1>CAM3
WhenCAM3hasreversepriority,orderissetto:
CAM3>CAM1>CAM2
IMPORTANTNOTE:Keysdonotworkwhensystemisinreverse.
8
3
III.InstallationofPower/VideoHarness
VII. Install/RemoveSunShade
V. MonitorBracketInstallation
Plug in securely and tighten screws
Monitor
Installation
Top Clip-buckle
Complete
Bottom Clip-buckle
Remove
Top Clip-buckle
Video System NTSC
Image Pick-up Device Sharp 1/3” Color CCD
Horizontal Resolution 600 Horizontal lines
Minimum Illumination 0 LUX @ F2.0
Lenses Furnished Board Lens 2.8mm
Synchronous System Internal Synchronization
Operating Temp -4°F~122°F (-20°C~50°C)
Power Supply DC12v +/-10%
Waterproofing Criteria IP68K
Dimensions 74mm(W) x 55.5mm(D) x 63.5mm(H)
6
5
VIII. RemoteIntroduction
.
Exit menu and save the settings
Remote Control
Monitor
Mute
ON/OFF
Up
\
CAM Selection
Volume-
Volume+
Menu
Down
Call
Mode
Sleep
Language
Quad View Mode Switch
Horizontal Flip
Calendar
Vertical Flip
IX.ReplacingtheBatteryinyourremote
BatteryModel: 
CR2025

d.T‐DELAYsetup:
DefaultdelaytimeforeachCHis0S(seconds).You
canadjusttheamountofdelaytime(howlongthe
imageremainsonthescreenafterthetriggered
eventstops)inthefollowingincrements:0S,5S,10S,
15S,20S,25Sor30S
NOTE:The“scan”keywillnotfunctionwhena
triggerdelayisactivate
e.Language
ThedefaultlanguageofthemonitorisEnglish.
Alternativelanguageoptionsinclude:Chinese,
French,Deutsch,Italian,Spanish,Portuguese,
RussianDanish,PolishorDutch.
f.SystemSettings
BlueScreen
ON:Bluescreenwhennosignal
OFF:Blackscreenwhennosignal
Auto‐Brightness
ON:CDSsensorwilltestambientlight,ifless
than10lux,screenbrightnesswillautomatically
adjustandthekeybacklightingwillturnon
OFF:CDSsensorwillnotfunctionandkey
backlightingwillnotwork
RulerRefLineMode
ON:Referencelinewillalwaysbedisplayedon
videoimage
TRIG:Referencelinewillonlybedisplayedwhen
triggered
OFF:Referencelinewillneverbedisplayed
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Dakota Micro OverView DMOV-7M-C2 User manual

Type
User manual

Dakota Micro OverView DMOV-7M-C2 is an advanced 7-inch, high-resolution TFT LCD monitor designed for use in rear-view monitoring systems. It features a wide voltage input range of 11-32V, making it compatible with most vehicles. The monitor has three video channel inputs, allowing you to connect up to three cameras. It also supports manual or automatic image switching modes, giving you the flexibility to choose how the cameras are displayed. With its forward/mirror image selection, you can easily adjust the image to suit your preferences.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI