Philips Lightolier Controls CLMIR Programming And Operation Instructions

Brand: Philips

Model: Lightolier Controls CLMIR

Type: Programming And Operation Instructions

Philips Lightolier Controls CLMIR is a handheld infrared transmitter that allows you to control your lighting system wirelessly. With a range of approximately 75 feet, you can easily adjust the lighting in your home or office from anywhere within that range. The CLMIR can be programmed to control up to four different lighting groups, so you can create different scenes for different activities or moods. For example, you could have one group for general lighting, one for task lighting, and one for accent lighting.

PROGRAMMING AND

OPERATION INSTRUCTIONS

HANDHELD INFRARED TRANSMITTER - CLMIR

IMPORTANT: RETAIN THESE INSTRUCTIONS FOR THE END USER. DO NOT DISCARD.

CLMIR

HANDHELD INFRARED TRANSMITTER

Made in U.S.A. Technical/Sales assistance: 1-800-526-2731 P/N 85-6348A0

Lightolier Controls is a Philips Controls brand

CLMIR - HANDHELD INFRARED TRANSMITTER

Programming and Operation

Instructions

The CLMIR Handheld Infrared Transmitter is capable of

operating over an unobstructed range of approximately 75 feet.

Within this range, scenes can be selected, raised and lowered,

and lighting may be turned On and Off using the handheld,

wireless remote transmitter. In addition, the CLMIR is capable

of controlling up to four different Brilliance II, MultiSet Pro,

Compose PLC or Lytemode control station groups.

Description

Programming:

The wall keypad must be enabled to receive the IR signal before the sensor will work. To enable

the keypad, perform the following sequence of keystrokes on the keypad. The Handheld Infrared

Transmitter is already configured to control up to four different keypad addresses (rooms).

1. On the wall keypad, press and hold the A and D buttons

for three seconds. The A, B, C, D and OFF keys will

illuminate with one of them blinking. (The keypad may

be custom engraved to change the labels.) Button A

refers to the keypad being configured as Room 1, B to

Room 2, C to Room 3, and D to Room 4. If OFF is

blinking, the infrared receiver is disabled. Refer to the

drawing at right. The factory default is Room 1 (A).

2. Press the desired Room Number or OFF. This will con-

figure the keypad as that room or disable infrared

input. The selection will blink.

3. Press ON to save and exit.

Operation:

Use the CLMIR unit to remotely operate the corresponding con-

trol station.

NOTE: This system is based on line-of-sight operations, therefore, the receiver must be able to

“See” the transmitter. Any obstruction between the transmitter and receiver may adversely affect

the performance of the unit.

Programming and Operation

OFF

Ellipse Series

Wall Keypad

The CLMIR Handheld Infrared Transmitter is powered by two

AAA batteries (included).

1. Remove CLMIR unit and two AAA batteries from clam shell

package.

2. Install batteries in CLMIR unit and close compartment.

3. Proceed to Programming and Operation section.

Unpack Procedure

Lightolier Controls is a Philips Controls brand

Lightolier Controls

2828 Trade Center Drive, Suite 130B

Carrollton, Texas 75007

Technical/Sales assistance: 1-800-526-2731

www.lolcontrols.com P/N 85-6348A0

THREE YEAR LIMITED WARRANTY

The Philips Controls product, when properly installed and under normal conditions of use (without overload, abuse or alteration), is warranted to you, the original user, for a period

of three years form the date of original retail purchase, to be free from defects in materials and workmanship. If during the warranty period you believe the purchased product or any

part thereof has such a defect, you must return the product (or part) at your cost during such period, with proof of purchase (or if installed by a third-party a written explanation of

installation transaction with proof of date), to Philips Controls, 2828 Trade Center Dr. Ste. 130B, Carrollton, TX 75007, for repair or replacement (or to an authorized Philips Controls

supplier which agrees in advance to handle the return and replacement by factory authorization). If the product or part is found by Philips Controls to have been defective in material

or workmanship it will be repaired or replaced (as deemed necessary by Philips Controls), and the replacement will be returned to you free of charge. The original user is solely

responsible for any costs associated with removal and re-installation of the product and shipping to Philips Controls or its authorized supplier.

PHILIPS CONTROLS LIMITS THE DURATION OF THE IMPLIED WARRANTY OF MERCHANTABILITY WITH RESPECT TO THE PRODUCT TO THE LIMITED WARRANTY PERIOD SET FORTH

ABOVE, AND OTHERWISE DISCLAIMS ALL IMPLIED WARRANTIES WITH RESPECT TO THE PRODUCT AND ITS PARTS. Some states disallow certain limitations on implied warranties so

you should consult your state law if you have a questions regarding this limitation and disclaimer. Philips Controls disclaims any and all liability for incidental, consequential, special

or indirect damage arising out of any claimed breach of warranty or otherwise. However, some states do not allow exclusion or limitation of such damages, so this disclaimer may not

apply to you.

The remedy provided in the Limited Warranty for defective products is the user’s sole and exclusive remedy, subject to your state law. Further, this Warranty gives the user specific legal

rights, and the user may also have other rights which may vary from state to state.

If you believe warranty claim is warranted, you may contact your nearest authorized Philips Controls supplier. If one does not exist in your area, please contact Philips Controls Customer

Service at the above address (or at 1-800-526-2731), or please visit us at www.lolcontrols.com.

Philips Lightolier Controls CLMIR Programming And Operation Instructions

Philips Lightolier Controls CLMIR Programming And Operation Instructions

Philips Lightolier Controls CLMIR Programming And Operation Instructions

Related papers

Other documents