Juniper EX4500 Series User manual

  • Hello! I am an AI chatbot trained to assist you with the Juniper EX4500 Series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Complete Hardware Guide for EX4500 Ethernet
Switches
Published: 2011-11-15
Revision 7
Copyright © 2011, Juniper Networks, Inc.
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
This product includes the Envoy SNMP Engine, developed by Epilogue Technology, an Integrated Systems Company. Copyright © 1986-1997,
Epilogue Technology Corporation. All rights reserved. This program and its documentation were developed at private expense, and no part
of them is in the public domain.
This product includes memory allocation software developed by Mark Moraes, copyright © 1988, 1989, 1993, University of Toronto.
This product includes FreeBSD software developed by the University of California, Berkeley, and its contributors. All of the documentation
and software included in the 4.4BSD and 4.4BSD-Lite Releases is copyrighted by the Regents of the University of California. Copyright ©
1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994. The Regents of the University of California. All rights reserved.
GateD software copyright © 1995, the Regents of the University. All rights reserved. Gate Daemon was originated and developed through
release 3.0 by Cornell University and its collaborators. Gated is based on Kirton’s EGP, UC Berkeley’s routing daemon (routed), and DCN’s
HELLO routing protocol. Development of Gated has been supported in part by the National Science Foundation. Portions of the GateD
software copyright © 1988, Regents of the University of California. All rights reserved. Portions of the GateD software copyright © 1991, D.
L. S. Associates.
This product includes software developed by Maker Communications, Inc., copyright © 1996, 1997, Maker Communications, Inc.
Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United
States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other
trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners.
Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify,
transfer, or otherwise revise this publication without notice.
Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are
owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312,
6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
Complete Hardware Guide for EX4500 Ethernet Switches
Copyright © 2011, Juniper Networks, Inc.
All rights reserved.
Revision History
May 2010—Revision 1
August 2010—Revision 2
December 2010—Revision 3
March 2011—Revision 4
July 2011—Revision 5
September 2011—Revision 6
November 2011—Revision 7
The information in this document is current as of the date listed in the revision history.
YEAR 2000 NOTICE
Juniper Networks hardware and software products are Year 2000 compliant. Junos OS has no known time-related limitations through the
year 2038. However, the NTP application is known to have some difficulty in the year 2036.
SOFTWARE LICENSE
The terms and conditions for using this software are described in the software license contained in the acknowledgment to your purchase
order or, to the extent applicable, to any reseller agreement or end-user purchase agreement executed between you and Juniper Networks.
By using this software, you indicate that you understand and agree to be bound by those terms and conditions.
Copyright © 2011, Juniper Networks, Inc.ii
Generally speaking, the software license restricts the manner in which you are permitted to use the software and may contain prohibitions
against certain uses. The software license may state conditions under which the license is automatically terminated. You should consult
the license for further details.
For complete product documentation, please see the Juniper Networks Web site at www.juniper.net/techpubs.
END USER LICENSE AGREEMENT
The Juniper Networks product that is the subject of this technical documentation consists of (or is intended for use with) Juniper Networks
software. Use of such software is subject to the terms and conditions of the End User License Agreement (“EULA”) posted at
http://www.juniper.net/support/eula.html. By downloading, installing or using such software, you agree to the terms and conditions
of that EULA.
iiiCopyright © 2011, Juniper Networks, Inc.
Copyright © 2011, Juniper Networks, Inc.iv
Table of Contents
About This Topic Collection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
How to Use This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii
List of EX Series Guides for Junos OS Release 11.4 . . . . . . . . . . . . . . . . . . . . . . . . . xvii
Downloading Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xix
Documentation Symbols Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xx
Documentation Feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxi
Requesting Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxii
Self-Help Online Tools and Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxii
Opening a Case with JTAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxii
Part 1 Switch and Components Overview and Specifications
Chapter 1 EX4500 Switch Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
EX4500 Switches Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Intraconnect Module and Virtual Chassis Module . . . . . . . . . . . . . . . . . . . . . . . 5
Uplink Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
EX4500 Switch Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Identifying EX4500 Switch Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chassis Physical Specifications for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . 11
Front Panel of an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Rear Panel of an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
EX4500 Switch Hardware and CLI Terminology Mapping . . . . . . . . . . . . . . . . . . . 15
Chapter 2 Component Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LCD Panel in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
LCD Panel Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
LCD Panel Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chassis Status LEDs in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Field-Replaceable Units in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Network Port and Uplink Module Port LEDs in EX4500 Switches . . . . . . . . . . . . . 24
Management Port LEDs in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
AC Power Supply in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
AC Power Supply LEDs in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
DC Power Supply in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
DC Power Supply LEDs in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cooling System and Airflow in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . 33
Uplink Modules in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Intraconnect Module in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Virtual Chassis Module in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
vCopyright © 2011, Juniper Networks, Inc.
Chapter 3 Component Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
USB Port Specifications for an EX Series Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Console Port Connector Pinout Information for an EX Series Switch . . . . . . . . . . 42
Management Port Connector Pinout Information for an EX4500 Switch . . . . . . . 43
Network Port and Uplink Module Port Connector Pinout Information for EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Virtual Chassis Ports Connector Pinout Information for EX4500 Switches . . . . . 45
Optical Interface Support in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
SFP+ Direct Attach Cables for EX Series Switches . . . . . . . . . . . . . . . . . . . . . . . . 64
Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Standards Supported by These Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Grounding Cable and Lug Specifications for EX4500 Switches . . . . . . . . . . . . . . 68
Part 2 Planning for Switch Installation
Chapter 4 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Site Preparation Checklist for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . 73
General Site Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Site Electrical Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Environmental Requirements and Specifications for EX Series Switches . . . . . . . 76
Chapter 5 Rack and Cabinet Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Rack Requirements for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Cabinet Requirements for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Clearance Requirements for Airflow and Hardware Maintenance for EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Chapter 6 Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Network Cable Specifications for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . 85
Chapter 7 Planning Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
AC Power Specifications for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
DC Power Specifications for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
AC Power Cord Specifications for an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . 88
Chapter 8 Planning the Virtual Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Understanding EX4200 and EX4500 Virtual Chassis Hardware
Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Ports Used to Interconnect Virtual Chassis Members . . . . . . . . . . . . . . . . . . . 91
Number of Switches, Required Software Releases, and Member Roles That
You Configure in the Virtual Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Virtual Chassis Module—a Required Component for Virtual Chassis That
Include EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Switch Role and Member ID on the LCD Panel . . . . . . . . . . . . . . . . . . . . . . . . 93
Planning EX4200 and EX4500 Virtual Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Copyright © 2011, Juniper Networks, Inc.vi
Complete Hardware Guide for EX4500 Ethernet Switches
Part 3 Installing and Connecting the Switch and Switch Components
Chapter 9 Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Installing and Connecting an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Unpacking an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Parts Inventory (Packing List) for an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . 100
Mounting an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Mounting an EX4500 Switch on Two Posts in a Rack or Cabinet . . . . . . . . . . . . 102
Mounting an EX4500 Switch on Four Posts in a Rack or Cabinet . . . . . . . . . . . . 104
Mounting an EX4500 Switch in a Recessed Position in a Rack or Cabinet . . . . . 107
Chapter 10 Installing Switch Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Installing and Removing EX4500 Switch Hardware Components . . . . . . . . . . . 109
Installing an AC Power Supply in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . 110
Installing a DC Power Supply in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . 112
Installing a Fan Tray in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Installing an Uplink Module in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . 115
Installing an Intraconnect Module in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . 117
Installing a Virtual Chassis Module in an EX4500 Switch . . . . . . . . . . . . . . . . . . . 119
Connecting a Virtual Chassis Cable to an EX4500 Switch . . . . . . . . . . . . . . . . . . 121
Installing a Transceiver in an EX Series Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Chapter 11 Connecting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Connecting Earth Ground to an EX Series Switch . . . . . . . . . . . . . . . . . . . . . . . . . 125
Connecting Earth Ground to an EX2200, EX3200, or EX3300 Switch . . . . . 126
Connecting Earth Ground to an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . 127
Connecting Earth Ground to an EX6210 Switch . . . . . . . . . . . . . . . . . . . . . . . 128
Connecting Earth Ground to an EX8208 Switch . . . . . . . . . . . . . . . . . . . . . . 129
Connecting Earth Ground to an EX8216 Switch . . . . . . . . . . . . . . . . . . . . . . . 130
Connecting AC Power to an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Connecting DC Power to an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Connecting an EX Series Switch to a Network for Out-of-Band Management . . 137
Connecting an EX Series Switch to a Management Console . . . . . . . . . . . . . . . . 138
Connecting an EX Series Switch to a Management Console Using RJ-45
Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Connecting an EX2200 Switch to a Management Console Using Mini-USB
Type-B Console Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Connecting an EX Series Switch to a Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Setting the Serial Console Speed for the Switch . . . . . . . . . . . . . . . . . . . . . . 141
Configuring the Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
Connecting the Modem to the Console Port . . . . . . . . . . . . . . . . . . . . . . . . . 143
Connecting a Fiber-Optic Cable to an EX Series Switch . . . . . . . . . . . . . . . . . . . . 145
Chapter 12 Performing Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
EX4500 Default Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Connecting and Configuring an EX Series Switch (CLI Procedure) . . . . . . . . . . . 153
Connecting and Configuring an EX Series Switch (J-Web Procedure) . . . . . . . . . 155
viiCopyright © 2011, Juniper Networks, Inc.
Table of Contents
Part 4 Removing the Switch and Switch Components
Chapter 13 Removing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Removing an EX4500 Switch from a Rack or Cabinet . . . . . . . . . . . . . . . . . . . . . 161
Chapter 14 Removing Switch Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Installing and Removing EX4500 Switch Hardware Components . . . . . . . . . . . . 163
Removing an AC Power Supply from an EX4500 Switch . . . . . . . . . . . . . . . . . . . 164
Removing a DC Power Supply from an EX4500 Switch . . . . . . . . . . . . . . . . . . . . 166
Removing a Fan Tray from an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
Removing an Uplink Module from an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . 169
Removing an Intraconnect Module from an EX4500 Switch . . . . . . . . . . . . . . . . . 171
Removing a Virtual Chassis Module from an EX4500 Switch . . . . . . . . . . . . . . . . 173
Disconnecting a Virtual Chassis Cable from an EX4500 Switch . . . . . . . . . . . . . 176
Disconnecting a Fiber-Optic Cable from an EX Series Switch . . . . . . . . . . . . . . . . 177
Removing a Transceiver from an EX Series Switch . . . . . . . . . . . . . . . . . . . . . . . . 178
Part 5 Switch and Component Maintenance
Chapter 15 Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Maintaining Fiber-Optic Cables in EX Series Switches . . . . . . . . . . . . . . . . . . . . . 183
Part 6 Troubleshooting Switch Issues
Chapter 16 Troubleshooting Switch Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187
Troubleshooting the Boot Process on EX4500 Switches . . . . . . . . . . . . . . . . . . . 187
Part 7 Returning Hardware
Chapter 17 Returning the Switch or Switch Components . . . . . . . . . . . . . . . . . . . . . . . . . 191
Returning an EX4500 Switch or Component for Repair or Replacement . . . . . . . 191
Locating the Serial Number on an EX4500 Switch or Component . . . . . . . . . . . 192
Listing the Switch and Components Details with the CLI . . . . . . . . . . . . . . . 192
Locating the Chassis Serial Number ID Label on an EX4500 Switch . . . . . . 193
Locating the Serial Number ID Labels on FRUs in an EX4500 Switch . . . . . 193
Contacting Customer Support to Obtain Return Materials Authorization for EX
Series Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Packing an EX4500 Switch or Component for Shipping . . . . . . . . . . . . . . . . . . . 197
Packing an EX4500 Switch for Shipping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197
Packing EX4500 Switch Components for Shipping . . . . . . . . . . . . . . . . . . . 198
Part 8 Safety Information
Chapter 18 General Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
General Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Definitions of Safety Warning Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Fire Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Qualified Personnel Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Warning Statement for Norway and Sweden . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Copyright © 2011, Juniper Networks, Inc.viii
Complete Hardware Guide for EX4500 Ethernet Switches
Chapter 19 Radiation and Laser Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Laser and LED Safety Guidelines and Warnings for EX Series Switches . . . . . . . 209
General Laser Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Class 1 Laser Product Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
Laser Beam Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210
Radiation from Open Port Apertures Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Chapter 20 Installation and Maintenance Safety Information . . . . . . . . . . . . . . . . . . . . . 213
Installation Instructions Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Chassis Lifting Guidelines for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Ramp Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Rack-Mounting and Cabinet-Mounting Warnings . . . . . . . . . . . . . . . . . . . . . . . . . 216
Grounded Equipment Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Maintenance and Operational Safety Guidelines and Warnings . . . . . . . . . . . . . 220
Jewelry Removal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Lightning Activity Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Operating Temperature Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Product Disposal Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Chapter 21 Power and Electrical Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
General Electrical Safety Guidelines and Warnings . . . . . . . . . . . . . . . . . . . . . . . 227
Prevention of Electrostatic Discharge Damage . . . . . . . . . . . . . . . . . . . . . . . . . . 228
AC Power Electrical Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
AC Power Disconnection Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231
DC Power Electrical Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232
DC Power Disconnection Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
DC Power Grounding Requirements and Warning . . . . . . . . . . . . . . . . . . . . . . . . 236
DC Power Wiring Sequence Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237
DC Power Wiring Terminations Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238
Multiple Power Supplies Disconnection Warning . . . . . . . . . . . . . . . . . . . . . . . . . 240
TN Power Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240
Action to Take After an Electrical Accident . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Part 9 Compliance Information
Chapter 22 Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Agency Approvals for EX Series Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Compliance Statements for EMC Requirements for EX Series Switches . . . . . . 246
Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
European Community . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
Korea . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
FCC Part 15 Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Non-Regulatory Environmental Standards . . . . . . . . . . . . . . . . . . . . . . . . . . 248
Compliance Statements for Acoustic Noise for EX Series Switches . . . . . . . . . . 249
Declaration of Conformity for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . 249
ixCopyright © 2011, Juniper Networks, Inc.
Table of Contents
Copyright © 2011, Juniper Networks, Inc.x
Complete Hardware Guide for EX4500 Ethernet Switches
List of Figures
Part 1 Switch and Components Overview and Specifications
Chapter 1 EX4500 Switch Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Figure 1: EX4500 Switch Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Figure 2: EX4500 Switch Rear with Intraconnect Module Installed . . . . . . . . . . . . . 4
Figure 3: EX4500 Switch Rear with Virtual Chassis Module Installed . . . . . . . . . . . 5
Figure 4: EX4500 Switch Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 5: Label Identifying CEE Capable EX4500 Switches . . . . . . . . . . . . . . . . . . 13
Figure 6: EX4500 Switch Rear Panel with an Intraconnect Module Installed . . . . 14
Figure 7: EX4500 Switch Rear Panel with a Virtual Chassis Module Installed . . . . 14
Chapter 2 Component Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 8: LCD Panel in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 9: Chassis Status LEDs in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 10: Network Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 11: Uplink Module Port LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 12: LEDs on the Management Port on an EX4500 Switch . . . . . . . . . . . . . . 26
Figure 13: AC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 14: Power Cord Retainer for an AC Power Supply . . . . . . . . . . . . . . . . . . . . 28
Figure 15: AC Power Supply LEDs in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . 29
Figure 16: DC Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 17: DC Power Supply LED in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . 32
Figure 18: Fan Tray Used in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 19: Front-to-Back Airflow Through the EX4500 Switch Chassis . . . . . . . . 34
Figure 20: Back-to-Front Airflow Through the EX4500 Switch Chassis . . . . . . . . 35
Figure 21: Uplink Module Slots in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 22: SFP+ Uplink Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 23: Intraconnect Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 24: Virtual Chassis Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Figure 25: Virtual Chassis Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Part 2 Planning for Switch Installation
Chapter 5 Rack and Cabinet Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Figure 26: Front-to-Back Airflow Through the EX4500-40F-FB Switch
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 27: Back-to-Front Airflow Through the EX4500-40F-BF Switch
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Figure 28: Clearance Requirements for Airflow and Hardware Maintenance for
an EX4500 Switch Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Chapter 7 Planning Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
xiCopyright © 2011, Juniper Networks, Inc.
Figure 29: AC Plug Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Part 3 Installing and Connecting the Switch and Switch Components
Chapter 9 Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Figure 30: Attaching the Mounting Bracket Along the Front of the Switch . . . . . 103
Figure 31: Mounting the Switch on Two Posts in a Rack . . . . . . . . . . . . . . . . . . . . 104
Figure 32: Attaching the Front Bracket to the Switch Chassis . . . . . . . . . . . . . . . 106
Figure 33: Mounting the Switch on the Front Posts in a Rack . . . . . . . . . . . . . . . . 106
Figure 34: Sliding the Rear Brackets to the Rear of a Four-Post Rack . . . . . . . . . 107
Chapter 10 Installing Switch Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Figure 35: Installing a Power Supply in an EX4500 Switch . . . . . . . . . . . . . . . . . . . 111
Figure 36: Installing a DC Power Supply in an EX4500 Switch . . . . . . . . . . . . . . . 113
Figure 37: Installing a Fan Tray in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . 114
Figure 38: Uplink Module Slots in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . 115
Figure 39: Installing an Uplink Module in an EX4500 Switch . . . . . . . . . . . . . . . . 116
Figure 40: Installing an Intraconnect Module in an EX4500 Switch . . . . . . . . . . . 119
Figure 41: Installing the Virtual Chassis Module in an EX4500 Switch . . . . . . . . . 121
Figure 42: Connecting a Virtual Chassis Cable to a Dedicated VCP on a Virtual
Chassis Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Figure 43: Installing a Transceiver in an EX Series Switch . . . . . . . . . . . . . . . . . . . 124
Chapter 11 Connecting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Figure 44: Connecting a Grounding Cable to an EX Series Switch . . . . . . . . . . . . 125
Figure 45: Location of Protective Earthing Terminal on an EX6210 Switch . . . . . 128
Figure 46: Power Cord Retainer in an AC Power Supply . . . . . . . . . . . . . . . . . . . . 132
Figure 47: Connecting the Power Supply Cord to an EX4500 Switch . . . . . . . . . . 133
Figure 48: Remove Plastic Cover from Terminal Block . . . . . . . . . . . . . . . . . . . . . 135
Figure 49: Connecting the Power Supply Cables to an EX4500 Switch . . . . . . . 136
Figure 50: Install Plastic Cover on Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . 136
Figure 51: Ethernet Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Figure 52: Connecting an EX Series Switch to a Network for Out-of-Band
Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Figure 53: Ethernet Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Figure 54: Connecting an EX Series Switch to a Management Console Through
a Console Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Figure 55: Connecting an EX Series Switch Directly to a Management
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Figure 56: Ethernet Cable Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Figure 57: Connecting a Fiber-Optic Cable to an Optical Transceiver Installed in
an EX Series Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Chapter 12 Performing Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
Figure 58: LCD Panel in an EX3200, EX4200, EX4500, or EX8200 Switch . . . . . 156
Part 4 Removing the Switch and Switch Components
Chapter 14 Removing Switch Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Figure 59: Removing a Power Supply from an EX4500 Switch . . . . . . . . . . . . . . 166
Figure 60: Removing a DC Power Supply from an EX4500 Switch . . . . . . . . . . . 167
Copyright © 2011, Juniper Networks, Inc.xii
Complete Hardware Guide for EX4500 Ethernet Switches
Figure 61: Removing a Fan Tray from an EX4500 Switch . . . . . . . . . . . . . . . . . . . 169
Figure 62: Removing an Uplink Module from an EX4500 Switch . . . . . . . . . . . . . 170
Figure 63: Removing an Intraconnect Module from an EX4500 Switch . . . . . . . . 173
Figure 64: Removing the Virtual Chassis Module from an EX4500 Switch . . . . . 175
Figure 65: Disconnecting a Virtual Chassis Cable from a Dedicated VCP on a
Virtual Chassis Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Figure 66: Removing a Transceiver from an EX Series Switch . . . . . . . . . . . . . . . 179
Part 7 Returning Hardware
Chapter 17 Returning the Switch or Switch Components . . . . . . . . . . . . . . . . . . . . . . . . . 191
Figure 67: Location of the Serial Number ID Label on an EX4500 Switch . . . . . . 193
Figure 68: Location of the Serial Number ID Label on an AC Power Supply Used
in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Figure 69: Location of the Serial Number ID Label on the Fan Tray Used in an
EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Figure 70: Location of the Serial Number ID Label on the Virtual Chassis Module
Used in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Part 8 Safety Information
Chapter 21 Power and Electrical Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227
Figure 71: Place a Component into an Antistatic Bag . . . . . . . . . . . . . . . . . . . . . . 229
Part 9 Compliance Information
Chapter 22 Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Figure 72: Declaration of Conformity for the EU . . . . . . . . . . . . . . . . . . . . . . . . . . 250
Figure 73: Suppliers Declaration of Conformity for Australia and New
Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251
xiiiCopyright © 2011, Juniper Networks, Inc.
List of Figures
Copyright © 2011, Juniper Networks, Inc.xiv
Complete Hardware Guide for EX4500 Ethernet Switches
List of Tables
Part 1 Switch and Components Overview and Specifications
Chapter 1 EX4500 Switch Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 1: EX4500 Switch Models, Components, and Supported Junos OS
Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 2: Physical Specifications of the EX4500 Switch Chassis . . . . . . . . . . . . . . . 11
Table 3: CLI Equivalents of Terms Used in Documentation for EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chapter 2 Component Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 4: LCD Panel Menu Options in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . 19
Table 5: Chassis Status LEDs in an EX4500 Switch . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 6: Link/Activity LED on Network Ports and Uplink Module Ports in EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 7: Status LED on Network Ports and Uplink Module Ports in EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 8: Link/Activity LED on the Management Port on an EX4500 Switch . . . . . 27
Table 9: Status LED on the Management Port on an EX4500 Switch . . . . . . . . . . 27
Table 10: Power Supply LED on EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . 29
Table 11: DC Power Supply LED on EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . 32
Table 12: Airfow Direction in EX4500 Switch Models . . . . . . . . . . . . . . . . . . . . . . . 33
Table 13: Uplink Module Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table 14: Intraconnect Module Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table 15: Virtual Chassis Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Chapter 3 Component Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 16: EX Series Switches Console Port Connector Pinout Information . . . . . . 42
Table 17: Management Port Connector Pinout Information for EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table 18: Network Port and Uplink Module Port Connector Pinout Information
for EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table 19: Virtual Chassis Ports (VCPs) Connector Pinout Information . . . . . . . . . 45
Table 20: Optical Interface Support and Copper Interface Support for Gigabit
Ethernet SFP Transceivers in EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . 49
Table 21: Optical Interface Support for Gigabit Ethernet SFP+ Transceivers in
EX4500 Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 22: Software Support for SFP+ Direct Attach Cables for EX Series
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 23: SFP+ Direct Attach Cable Specifications . . . . . . . . . . . . . . . . . . . . . . . . 66
xvCopyright © 2011, Juniper Networks, Inc.
Part 2 Planning for Switch Installation
Chapter 4 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 24: Site Preparation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 25: Site Electrical Wiring Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Table 26: EX Series Switch Environmental Tolerances . . . . . . . . . . . . . . . . . . . . . . 77
Chapter 5 Rack and Cabinet Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Table 27: Rack Requirements and Specifications for the Switch . . . . . . . . . . . . . . 79
Table 28: Cabinet Requirements and Specifications for the Switch . . . . . . . . . . . 81
Chapter 7 Planning Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 29: Power Specifications for an AC Power Supply Used in EX4500
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Table 30: Power Specifications for the DC Power Supply Used in an EX4500
Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Table 31: AC Power Cord Specifications for an EX4500 Switch . . . . . . . . . . . . . . 88
Chapter 8 Planning the Virtual Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Table 32: Number of Switches and Switch Roles for an EX4200 Virtual Chassis,
per Junos OS Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table 33: Number of Switches and Switch Roles for an EX4500 Virtual Chassis,
per Junos OS Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table 34: Number of Switches and Switch Roles for a Mixed EX4200 and EX4500
Virtual Chassis, per Junos OS Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Table 35: Virtual Chassis Components to Consider when Planning an EX4200
and EX4500 Virtual Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Table 36: Cabling Requirements for a Virtual Chassis . . . . . . . . . . . . . . . . . . . . . . 94
Part 3 Installing and Connecting the Switch and Switch Components
Chapter 9 Installing the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Table 37: Inventory of Components Provided with an EX4500 Switch . . . . . . . . . 101
Chapter 11 Connecting the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Table 38: Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
Copyright © 2011, Juniper Networks, Inc.xvi
Complete Hardware Guide for EX4500 Ethernet Switches
About This Topic Collection
How to Use This Guide on page xvii
List of EX Series Guides for Junos OS Release 11.4 on page xvii
Downloading Software on page xix
Documentation Symbols Key on page xx
Documentation Feedback on page xxi
Requesting Technical Support on page xxii
How to Use This Guide
Complete documentation for the EX Series product family is provided on webpages at
http://www.juniper.net/techpubs/en_US/release-independent/information-products/
pathway-pages/ex-series/product/index.html. We have selected content from these
webpages and created a number of EX Series guides that collect related topics into a
book-like format so that the information is easy to print and easy to download to your
local computer.
Software features for EX Series switches are listed by platform and by Junos OS release
in a standalone document. See EX Series Switch Software Features Overview.
This guide, Complete Hardware Guide for EX4500 Ethernet Switches, collects together
information about the EX4500 switches. The release notes are at
http://www.juniper.net/techpubs/en_US/junos11.4/
information-products/topic-collections/release-notes/11.4/junos-release-notes-11.4.pdf.
List of EX Series Guides for Junos OS Release 11.4
DescriptionTitle
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX2200 Ethernet switches
Complete Hardware Guide for EX2200 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX3200 Ethernet switches
Complete Hardware Guide for EX3200 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX3300 Ethernet switches
Complete Hardware Guide for EX3300 Ethernet Switches
xviiCopyright © 2011, Juniper Networks, Inc.
DescriptionTitle
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX4200 Ethernet switches
Complete Hardware Guide for EX4200 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX4500 Ethernet switches
Complete Hardware Guide for EX4500 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX6210 Ethernet switches
Complete Hardware Guide for EX6210 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX8208 Ethernet switches
Complete Hardware Guide for EX8208 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for EX8216 Ethernet switches
Complete Hardware Guide for EX8216 Ethernet Switches
Component descriptions, site preparation, installation,
replacement, and safety and compliance information
for the XRE200 External Routing Engine
Complete Hardware Guide for the XRE200 External Routing Engine
Software feature descriptions, configuration examples,
and tasks for Junos OS for EX Series switches
Complete Software Guide for Junos
®
OS for EX Series Ethernet
Switches, Release 11.4
Software feature descriptions, configuration examples
and tasks, and reference pages for configuration
statements and operational commands (This
information also appearsin the Complete Software Guide
for Junos
®
OS for EX Series Ethernet Switches, Release
11.4.)
Software Topic Collections
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Access and
User Management
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Access Control
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Configuration
Management
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Class of
Service
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Device Security
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Ethernet
Switching
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: EX3300,
EX4200, and EX4500 Virtual Chassis
Copyright © 2011, Juniper Networks, Inc.xviii
Complete Hardware Guide for EX4500 Ethernet Switches
DescriptionTitle
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: EX8200 Virtual
Chassis
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Fibre Channel
over Ethernet
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: High
Availability
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Interfaces
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Layer 3
Protocols
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: MPLS
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Multicast
Junos
®
OS for EX Series Switches, Release 11.4: Network Management
and Monitoring
Junos
®
OS for EX Series Switches, Release 11.4: Port Security
Junos
®
OS for EX Series Switches, Release 11.4: Power over Ethernet
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Routing Policy
and Packet Filtering
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Software
Installation
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: Spanning-Tree
Protocols
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: System
Monitoring
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: System
Services
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: System Setup
Junos
®
OS for EX Series Ethernet Switches, Release 11.4: User Interfaces
Downloading Software
You can download Junos OS for EX Series switches from the Download Software area
at http://www.juniper.net/customers/support/ . To download the software, you must
xixCopyright © 2011, Juniper Networks, Inc.
About This Topic Collection
have a Juniper Networks user account. For information about obtaining an account, see
http://www.juniper.net/entitlement/setupAccountInfo.do.
Documentation Symbols Key
Notice Icons
DescriptionMeaningIcon
Indicates important features or instructions.Informational note
Indicates a situation that might result in loss of data or hardware
damage.
Caution
Alerts you to the risk of personal injury or death.Warning
Alerts you to the risk of personal injury from a laser.Laser warning
Text and Syntax Conventions
ExamplesDescriptionConvention
To enter configuration mode, type the
configure command:
user@host> configure
Represents text that you type.Bold text like this
user@host> show chassis alarms
No alarms currently active
Represents output that appears on the
terminal screen.
Fixed-width text like this
A policy term is a named structure that
defines match conditions and actions.
Junos OS System Basics Configuration
Guide
RFC 1997, BGP Communities Attribute
Introduces important new terms.
Identifies book names.
Identifies RFC and Internet draft titles.
Italic text like this
Configure the machine’s domain name:
[edit]
root@# set system domain-name
domain-name
Represents variables (options for which
you substitute a value) in commands or
configuration statements.
Italic text like this
To configure a stub area, include the
stub statement at the [edit protocols
ospf area area-id] hierarchy level.
The console port is labeled CONSOLE.
Represents names of configuration
statements, commands, files, and
directories; IP addresses; configuration
hierarchy levels; or labels on routing
platform components.
Plain text like this
Copyright © 2011, Juniper Networks, Inc.xx
Complete Hardware Guide for EX4500 Ethernet Switches
/