Empire DVC-35-SPP Owner's manual

Brand: Empire

Model: DVC-35-SPP

Type: Owner's manual

This manual is also suitable for

Page 1

INSTALLATION INSTRUCTIONS

AND

OWNER’S MANUAL

FAN TYPE

DIRECT VENT

WALL FURNACE

MODEL

DVC-35

This appliance may be installed in an aftermarket,

permanently located manufactured home (USA only)

or mobile home, where not prohibited by state or lo-

cal codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certiﬁed

kit is used.

WARNING: If not installed, operated and main-

tained in accordance with the manufacturer’s in-

structions, this product could expose you to substanc-

es in fuel or from fuel combustion which can cause

death or serious illness.

Installer: Leave this manual with the appli-

ance.

Consumer: Retain this manual for future refer-

ence.

— Do not store or use gasoline or other ﬂamma-

ble vapors and liquids in the vicinity of this or

any other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-

er’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

— Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING: If the information in these instruc-

tions are not followed exactly, a ﬁre or explosion

may result causing property damage, personal

injury or loss of life.

12430-11-1008Page 2

TABLE OF CONTENTS

Important Safety Information .................................................................................................3

Safety Information for Users of LP Gas .................................................................................4

Requirements for Massachusetts ............................................................................................5

Introduction ............................................................................................................................6

Speciﬁcations .........................................................................................................................6

Gas Supply ......................................................................................................................... 7-8

Clearances ..............................................................................................................................8

Installation Instructions .................................................................................................... 9-11

DVC-35SPP Standing Pilot Lighting Instructions ...............................................................12

DVC-35IP Intermittent Pilot Lighting Instructions ..............................................................13

Pilot Flame Characteristics ...................................................................................................14

Main Burner Flame Characteristics ......................................................................................15

Wiring ............................................................................................................................. 15-16

Service and Maintenance Suggestions .................................................................................17

DVC-35IP Intermittent Pilot Sequence of Operation ...........................................................18

DVC-35IP Intermittent Pilot System Troubleshooting Sequence ........................................19

How to Order Repair Parts ...................................................................................................20

Parts List ...............................................................................................................................20

Parts View .............................................................................................................................21

Service Notes .................................................................................................................. 22-23

SECTION PAGE

12430-11-1008 Page 3

IMPORTANT SAFETY INFORMATION

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANEL INSTALLED.

• Due to high temperatures, the appliance should be located

out of trafﬁc and away from furniture and draperies.

• Children and adults should be alerted to the hazards of

high surface temperatures and should stay away to avoid

burns or clothing ignition.

• Young children should be carefully supervised when they

are in the same room as the appliance.

• Clothing or other ﬂammable material should not be placed

on or near the appliance.

• Any safety screen or guard removed for servicing an

appliance must be replaced prior to operating the appli-

ance.

• Keep burner and control compartment clean.

• Vent cap hot while furnace is in operation.

• Installation and repair should be done by a QUALIFIED

SERVICE PERSON. The appliance should be inspected

before use and at least annually by a qualiﬁed service

person. More frequent cleaning may be required due to

excessive lint from carpeting, bedding materials, etc. It

is imperative that control compartments, burners and

circulating air passageways of the appliance be kept

clean.

• DO NOT put anything around the furnace that will ob-

struct the ﬂow of combustion and ventilation air.

• DO keep the appliance area clear and free from combus-

tible material, gasoline and other ﬂammable vapors and

liquids.

• DO examine venting system periodically and replace

damaged parts.

• DO make a periodic visual check of pilot and burners.

Clean and replace damaged parts.

• CAUTION: Pilot hole cover must be kept tightly closed

during operation.

• DO NOT use this heater if any part has been under water.

Immediately call a qualiﬁed service technician to inspect

the heater and to replace any part of the control system

and any gas control which has been under water.

IMPORTANT: This furnace has a washable perma-

nent type ﬁlter which should be cleaned at least once

per year before the heating season. For dirty or high

use areas, more frequent cleaning is required.

12430-11-1008Page 4

SAFETY INFORMATION FOR USERS OF LP-GAS

Propane (LP-Gas) is a ﬂammable gas which can cause ﬁres

and explosions. In its natural state, propane is odorless and

colorless. You may not know all the following safety precau-

tions which can protect both you and your family from an

accident. Read them carefully now, then review them point

by point with the members of your household. Someday,

when there may not be a minute to lose, everyone’s safety

will depend on knowing exactly what to do. If, after read-

ing the following information, you feel you still need more

information, please contact your gas supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That’s your signal to go into immediate action!

• Do not operate electric switches, light matches, use your

phone. Do not do anything that could ignite the gas.

•

Get everyone out of the building, vehicle, trailer, or area. Do

that IMMEDIATELY.

• Close all gas tank or cylinder supply valves.

• LP-Gas is heavier than air and may settle in low areas such

as basements. When you have reason to suspect a gas leak,

keep out of basements and other low areas. Stay out until

ﬁreﬁghters declare them to be safe.

• Use your neighbor’s phone and call a trained LP-Gas service

person and the ﬁre department. Even though you may not

continue to smell gas, do not turn on the gas again. Do not

re-enter the building, vehicle, trailer, or area.

• Finally, let the service man and ﬁreﬁghters check for escaped

gas. Have them air out the area before you return. Properly

trained LP-Gas service people should repair the leak, then

check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the

odor of the chemical put into the gas. You must ﬁnd out if you

can smell the odorant in propane. Smoking can decrease your

ability to smell. Being around an odor for a time can affect your

sensitivity or ability to detect that odor. Sometimes, other odors

in the area mask the gas odor. People may not smell the gas odor

or their minds are on something else. Thinking about smelling a

gas odor can make it easier to smell.

The odorant in LP-Gas is colorless, and it can fade under

some circumstances. For example, if there is an underground

leak, the movement of the gas through soil can ﬁlter the odorant.

Odorants in LP-Gas are subject to oxidation. This fading can oc-

cur if there is rust inside the storage tank or in iron gas pipes.

The

odorant in escaped gas can adsorb or absorb onto or into

walls, masonry and other materials and fabrics in a room. That

will take some of the odorant out of the gas, reducing its odor

intensity.

LP-Gas may stratify in a closed area, and the odor intensity could

vary at different levels. Since it is heavier than air, there may be

more odor at lower levels. Always be sensitive to the slightest

gas odor. If you detect any odor, treat it as a serious leak. Imme-

diately go into action as instructed earlier.

SOME POINTS TO REMEMBER

• Learn to recognize the odor of LP-gas. Your local LP-Gas

Dealer can give you a “Scratch and Sniff” pamphlet. Use it

to ﬁnd out what the propane odor smells like. If you suspect

that your LP-Gas has a weak or abnormal odor, call your

LP-Gas Dealer.

• If you are not qualiﬁed, do not light pilot lights, perform

service, or make adjustments to appliances on the LP-Gas

system. If you are qualiﬁed, consciously think about the

odor of LP-Gas prior to and while lighting pilot lights or

performing service or making adjustments.

• Sometimes a basement or a closed-up house has a musty

smell that can cover up the LP-Gas odor. Do not try to light

pilot lights, perform service, or make adjustments in an area

where the conditions are such that you may not detect the

odor if there has been a leak of LP-Gas.

• Odor fade, due to oxidation by rust or adsorption on walls

of new cylinders and tanks, is possible. Therefore, people

should be particularly alert and careful when new tanks or

cylinders are placed in service. Odor fade can occur in new

tanks, or reinstalled old tanks, if they are ﬁlled and allowed

to set too long before reﬁlling. Cylinders and tanks which

have been out of service for a time may develop internal rust

which will cause odor fade. If such conditions are suspected

to exist, a periodic sniff test of the gas is advisable. If you

have any question about the gas odor, call your LP-Gas

Dealer. Aperiodic sniff test of the LP-Gas is a good safety

measure under any condition.

• If, at any time, you do not smell the LP-Gas odorant and you

think you should, assume you have a leak. Then take the same

immediate action recommended above for the occasion when

you do detect the odorized LP-Gas.

• If you experience a complete “gas out” (the container is un-

der no vapor pressure), turn the tank valve off immediately.

If the container valve is left on, the container may draw in

some air through openings such as pilot light oriﬁces. If this

occurs, some new internal rusting could occur. If the valve is

left open, then treat the container as a new tank. Always be

sure your container is under vapor pressure by turning it off

at the container before it goes completely empty or having

it reﬁlled before it is completely empty.

12430-11-1008 Page 5

REQUIREMENTS FOR MASSACHUSETTS

For all side wall horizontally vented gas fueled equipment

installed in every dwelling, building or structure used in

whole or in part for residential purposes, including those

owned or operated by the Commonwealth and where the

side wall exhaust vent termination is less than seven (7) feet

above ﬁnished grade in the area of the venting, including but

not limited to decks and porches, the following requirements

shall be satisﬁed:

1. INSTALLATION OF CARBON MONOXIDE DETEC-

ORS. At the time of installation of the side wall horizontal

vented gas fueled equipment, the installing plumber or

gasﬁtter shall observe that a hard wired carbon monoxide

detector with an alarm and battery back-up is installed on

the ﬂoor level where the gas equipment is to be installed.

In addition, the installing plumber or gasﬁtter shall observe

that a battery operated or hard wired carbon monoxide

detector with an alarm is installed on each additional

level of the dwelling, building or structure served by

the side wall horizontal vented gas fueled equipment. It

shall be the responsibility of the property owner to secure

the services of qualiﬁed licensed professionals for the

installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an

attic, the hard wired carbon monoxide detector with

alarm and battery back-up may be installed on the

next adjacent ﬂoor level.

b. In the event that the requirements of this subdivision

can not be met at the time of completion of installa-

tion,

the owner shall have a period of thirty (30) days

to comply with the above requirements; provided,

however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an

alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS.

Each carbon monoxide detector as required in accordance

with the above provisions shall comply with NFPA 720

and be ANSI/UL 2034 listed and IAS certiﬁed.

3. SIGNAGE. A metal or plastic identiﬁcation plate shall be

permanently mounted to the exterior of the building at a

minimum height of eight (8) feet above grade directly in

line with the exhaust vent terminal for the horizontally

vented gas fueled heating appliance or equipment. The

sign shall read, in print size no less than one-half (1/2)

inch in size, “GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the

side wall horizontally vented gas fueled equipment shall

not approve the installation unless, upon inspection, the

inspector observes carbon monoxide detectors and signage

installed in accordance with the provisions of 248 CMR

5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt

from 248 CMR 5.08(2)(a)1 through 4:

1. The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the

most current edition of NFPA 54 as adopted by

the Board; and

2. Product Approved side wall horizontally vented

gas fueled equipment installed in a room or

structure separate from the dwelling, building or

structure used in whole or in part for residential

purposes.

EQUIPMENT VENTING SYSTEM PROVIDED.

When the manufacturer of Product Approved side

wall horizontally vented gas equipment provides a

venting system design or venting system components

with the equipment, the instructions provided by the

manufacturer for installation of the equipment and

the venting system shall include:

1. Detailed instructions for the installation of the

venting system design or the venting system

components; and

2. A complete parts list for the venting system design

or venting system.

(e) A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists for

venting instructions, and/or all venting design instruc-

tions

shall remain with the appliance or equipment

at the completion of the installation.

12430-11-1008Page 6

INTRODUCTION

Introduction

Always consult your local Building Department regarding regulations,

codes or ordinances which apply to the installation of a direct vent wall

furnace.

Instructions to Installer.

1. Installer must leave instruction manual with owner after installa-

tion.

2. Installer must have owner ﬁll out and mail warranty card supplied

with furnace.

3. Installer should show owner how to start and operate furnace and

thermostat.

General Information

This furnace is design certiﬁ

ed in accordance with American National

Standard/CSA Standard Z21.86b-2002 and CSA 2.32b-2002 by the

Canadian Standards Association, as a fan type direct vent wall furnace

to be installed according to these instructions.

Any

alteration of the original design, installed other than as shown

in these instructions or use with a type of gas not shown on the rat-

ing plate is the responsibility of the person and company making the

change.

Important

All correspondence should refer to complete Model No., Serial No., and

type of gas.

Notice: During initial ﬁring of this unit, its paint will bake out and smoke

will

occur. To prevent triggering of smoke alarms, ventilate the room in

which the unit is installed.

Installation on Rugs and

Tile

If this appliance is installed directly on carpeting, tile or other combus-

tible material other than wood ﬂooring, the appliance shall be installed

on a metal or wood panel extending the full width and depth of the

appliance.

The base referred to above does not mean the ﬁre-proof base as used on

wood stoves. The protection is for rugs that are extremely thick and light

colored tile.

Installation in Residential Garages

Gas utilization equipment in residential garages shall be installed so

that all burners and burner ignition devices are located not less than 18”

above the ﬂoor.

Such equipment shall be located, or protected, so it is not subject to phys-

ical damage by a moving vehicle.

Qualiﬁed Installing Agency

Installation and replacement of gas piping, gas utilization equipment or

accessories and repair and servicing of equipment shall be performed

only by a qualiﬁed agency. The term “qualiﬁed agency” means any indi-

vidual,

ﬁrm, corporation or company which either in person or through

a representative is engaged in and is responsible for (a) the installation

or replacement of gas piping or (b) the connection, installation, repair or

servicing of equipment, who is experienced in such work, familiar with

all precautions required and has complied with all the requirements of the

authority having jurisdiction.

The

installation must conform with local codes or, in the absence of local

codes, with the National Fuel Gas Code ANSI Z223.1/NFPA 54* Natural

Gas and Propane Installation Code, CSA B149.1.

* Available from the American National Standards Institute, Inc., 11 West 42nd St., New York,

N.Y. 10036

High Altitudes

For altitudes/elevations above 2,000 feet, input ratings should be reduced

at the rate of 4 percent for each 1,000 feet above sea level. For Canadian

high altitude applications, this appliance is suitable for installation at el-

evations between 0 feet and 4,500 feet without change.

Piezo Pilot Ignitor Instructions

Depressing the red button completely causes a spark to occur at the pilot.

This is a substitute for a match which requires opening the pilot hole

cover.

To light the pilot, it is important that the electrode be 1/8” from the ther-

mocouple. The spark must occur at the point the burner ﬂame hits the

thermocouple. The end of the electrode will be red hot with the pilot on.

On a new installation with air in the gas line, it is suggested that a match

be used. The match will light the pilot faster than the piezo under this

condition.

Warning:

Any change to this furnace or its control can be dangerous. This

is a heating appliance and any panel, door, or guard removed

for servicing an appliance must be replaced prior to operating

the appliance.

State of Massachusetts: The installation must be made by a licensed

plumber or gas ﬁtter in the Commonwealth of Massachusetts.

SPECIFICATIONS

Model DVC-35SPP DVC-35IP

Input BTU/HR 35,000 35,000

Height 72 1/2” 72 1/2”

idth 14 1/8” 14 1/8”

Depth 10 3/8” 10 3/8”

Gas Inlet 1/2” Pipe 1/2” Pipe

CFM 275 275

Accessories

SOR-1 Register

, Side Outlet

SOK-1 Side Outlet Kit, 10” (25.4cm) Boot

Assembly with Register

*DV-822 Vinyl Siding Vent Kit

*DV-822, Vinyl siding vent kit, adds 3” to wall depth. You must include the three (3) additional inches for TOTAL wall depth when ordering a

vent kit.

12430-11-1008 Page 7

GAS SUPPLY

Locating Gas Supply

The gas line can enter the unit either through the ﬂoor or outside

wall. The gas line opening should be made at this time. Location

of the opening will be determined by the position of ﬂoor joists

and the valve and union used for servicing.

Recommended Gas Pipe Diameter

Pipe Length

(Feet)

Schedule 40 Pipe

Inside Diameter

ubing, Type L

Outside Diameter

Nat. L.P

. Nat L.P.

0-10 1/2”

1.3 cm

3/8”

1.0 cm

1/2”

1.3 cm

3/8”

1.0 cm

10-40 1/2”

1.3 cm

1/2”

1.3 cm

5/8”

1.6 cm

1/2”

1.3 cm

40-100 1/2”

1.3cm

1/2”

1.3 cm

3/4”

1.9 cm

1/2”

1.3 cm

100-150 3/4”

1.9cm

1/2”

1.3 cm

7/8”

2.2 cm

3/4”

1.9 cm

Note: Never Use plastic pipe. Check to conﬁrm whether your lo-

cal codes allow copper tubing or galvanized.

Note: Since some municipalities have additional local codes, it is

always best to consult your local authority and installation code.

The use of the following gas connectors is recommended:

– ANS Z21.24 Appliance Connectors of Corrugated Metal Tub-

ing and Fittings

– ANS Z21.45 Assembled Flexible Appliance Connectors of

Other Than All-Metal Construction

The above connectors may be used if acceptable by the author-

ity having jurisdiction. The state of Massachusetts requires that a

ﬂexible appliance connector cannot exceed three feet in length.

FLEXIBLE GAS LINE CONNECTION

GAS SUPPLY

TEE HANDLE

FLEX TUBING

NPT NIPPLE

FLARE SHUT OFF V

ALVE

FLARE FITTING

RIGID GAS LINE CONNECTION

CLOSE NIPPLE

TEE HANDLE

NPT NIPPLE

NPT UNION

SHUT OFF V

ALVE

NPT GAS SUPPLY

Figure 1

Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/

CGA-B149 (.1 or .2) installation code.

Installing a New Main Gas Cock

Each appliance should have its own manual gas cock.

manual main gas cock should be located in the vicinity of the

unit. Where none exists, or where its size or location is not ad-

equate,

contact your local authorized installer for installation or

relocation.

Compounds used on threaded joints of gas piping shall be resis-

tant to the action of liqueﬁed petroleum gases. The gas lines must

be checked for leaks by the installer. This should be done with a

soap solution watching for bubbles on all exposed connections,

and if unexposed, a pressure test should be made.

Never use and exposed ﬂame to check for leaks. Appliance

must be disconnected from piping at inlet of control valve and

pipe capped or plugged for pressure test. Never pressure test

with appliance connected; control valve will sustain damage!

A gas valve and ground joint union should be installed in the gas

line upstream of the gas control to aid in servicing. It is required

by the National Fuel Gas Code that a drip line be installed near

the gas inlet. This should consist of a vertical length of pipe tee

connected into the gas line that is capped on the bottom in which

condensation and foreign particles may collect.

GAS SUPPLY PIPING

1/8 NPT PLUGGED HOLE

FOR TEST GAGE

GROUND JOINT UNION

3” MINIMUM

MANUAL SHUT-OFF VALVE

GAS SUPPLY

INLET

1/8 NPT PLUGGED HOLE

FOR TEST GAGE

GAS

VALVE

Pressure Testing of the Gas Supply System

1. To check the inlet pressure to the gas valve, a 1/8” N.P.T.

plugged tapping, accessible for test gauge connection, must

be placed immediately upstream of the gas supply connection

to the appliance.

2. The appliance and its individual shutoff valve must be discon-

nected from the gas supply piping system during any pressure

testing of that system at test pressures in excess of 1/2 psig

(3.5 kPa).

3. The appliance must be isolated from the gas supply piping

system by closing its individual manual shutoff valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig (3.5 kPA)

Attention! If one of the above procedures results in pressures in

excess of 1/2 psig (14” w.c) (3.5 kPa) on the appliance gas valve,

it will result in a hazardous condition.

Figure 2

Method of Installing a Tee Fitting Sediment Trap

12430-11-1008Page 8

CLEARANCES

Checking Manifold Pressure

Both Propane and Natural gas valves have a built-in pressure reg-

ulator in the gas valve. Natural gas models will have a manifold

pressure of approximately 4.0” w.c. (.996kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 5.0” w.c.

(1.245kPa) for the purpose of input adjustment to a maximum of

7.0” w.c. (1.743kPa). Propane gas models will have a manifold

pressure approximately 10.0” w.c. (2.49kPa) at the valve outlet

with the inlet pressure to the valve from a minimum of 11.0” w.c.

(2.739kPa) for the purpose of input adjustment to a maximum of

13.0” w.c. (3.237kPa).

A 1/8” N.P.T. plugged tapping, accessible for test gauge connec-

tion, is located on the outlet side of the gas control.

The built-in regulator comes on at approximately 1/4th pressure

and full on in 10 seconds.

TOP VIEW OF VALVE

PRESSURE REGULATOR

OUTLET PRESSURE TAP

GAS OUTLET

PILOT GAS OUTLET

PILOT ADJUSTMENT

SCREW BENEATH

COVER SCREW

MANUAL GAS COCK KNOB

RED RESET BUTTON

INLET PRESSURE T

GAS INLET

WRENCH BOSS

VENT

Figure 3

Figure 4

Pressure Testing of the Gas Supply System

1. In selecting a location for installation, it is necessary to provide

adequate accessibility clearances for servicing and proper in-

stallation.

A front clearance of 36” (91.4cm) is recommended.

Do not block outlet or inlet air openings on the front grill.

2. The DVC-35 minimum wall depth is 3/4” (19mm) and maxi-

mum wall depth is 10” (254mm). The maximum wall depth

may be extended to 19” (483mm) using the model DV-1190

extended ﬂue kit. The use of tubes not supplied by the manu-

facturer results in unsatisfactory performance.

3. The DVC-35 can be attached to the wall or recessed into the

wall up to 9 1/2” (241mm) in depth but the minimum 3/4”

(19mm) vent/air intake system wall depth must be maintained.

Example: If furnace is recessed into the wall at a depth of

9 1/2” (241mm), the minimum wall depth must be 10 1/4”

(260mm).

4. The wall in which the furnace is recessed has (0) zero clear-

ance to the furnace sides and top.

5. When using side discharge registers, SOR-1 or SOK-1, the

furnace cannot be recessed into the wall.

6. Clearance to sidewall or combustible material is 4”

(102mm).

7. Ceiling clearance is 4” (201mm).

8. Floor and rear wall clearance is (0) zero inches.

9. Clearance of 18” (457mm) is required to sidewall or combus-

tible material when ﬂush mounted SOR-1, side outlet register

is used.

10. The minimum distance from the center of the vent cap to the

nearest outside corner or obstruction is 12” (305mm).

The vent terminal of this direct vent appliance shall be located

at least 9” (229mm) from any opening through which ﬂue gases

could enter a building. The bottom of the vent terminal and the

air intake shall be located at least 12” (305mm) above grade. See

vent location, Figure 4.

ARNING: The nearest point of the vent cap should be a

minimum horizontal distance of six (6) feet (1.83m) from

any pressure regulator. In case of regulator malfunction,

the six (6) feet (1.83m) distance will reduce the chance of

gas entering the vent cap.

12430-11-1008 Page 9

INSTALLATION INSTRUCTIONS

Locating Wall Opening

The furnace is to be located on an outside wall. Locate wall studs

so that wall opening will be located between wall studs. The fur-

naces is 14 1/8” (358mm) in width and can be recessed between

standard 16” (406mm) on center wall stud. The wall opening re-

quired as shown in Figure 5 is a diameter of 7 1/2” (191mm).

A template is provided in furnace carton for positioning furnace

on the wall. Also, refer to Figure 5 and Figure 7 for positioning

the furnace on wall and for locating gas line connection.

Installing Optional Side Outlets

Side outlet register, SOR-1 may be installed on one or both sides

of the furnace at the required clearances of 18” (457mm) to adja-

cent wall or combustible material as shown in Figure 6.

1. Turn “OFF” all electric power to the furnace.

2. Remove the front panel from the furnace.

3. Remove the (2) #8 X 3/8” (9mm) screws that attach the inner

shield cover plate to the inner shield.

4. Scribe a line between the four dimples on the outer casing

side to form a square.

5. Drill a pilot hole within the scribed square on the outer casing.

Remove the sheet metal within the scribed square with a tin

snips or comparable tool. Attention! Do not cut the electrical

wires located between the outer casing and the inner shield.

6. Insert the 5” x 5” (127mm x 127mm) inner boot through the

outer casing. Align the clearance holes on the inner boot with

the crew holes on the inner shield. Attach inner boot to inner

shield with (2) #8 x 3/8” (9mm) screws removed in Step 3.

7. Place the register over the 5 1/2” (140mm) square opening

with the louvers set for the desired direction and mark the

mounting holes using the register as a template.

8. Drill (2) 1/8” diameter holes in cabinet side and attach the

9. Installation of SOR-1 is completed.

Side outlet kit, SOK-1, 10” (254mm) boot assembly with reg-

ister, for warm air discharge into an adjoining room may be in-

stalled on either side of the furnace at the required clearance of 4”

(102mm) to adjacent wall as shown in Figure 6.

To install SOK-1, please use step 1 through 5 in the SOR-1 in-

structions for DVC-35 furnaces. Then, use the following Steps to

complete the installation of the SOK-1.

1. Using the inner and outer boots as hole templates, mark and

drill (4) 1/8” (3mm) diameter holes in the inner shield and (4)

1/8” (3mm) diameter holes in the cabinet side.

2. Locate and cut a 6 3/4” (171mm) square opening through

wall.

3. Attach furnace to wall (see Attaching Furnace to Wall).

4. With furnace in place, after checking alignment of side outlet

opening in wall and furnace, place the 9 3/8” x 9 3/8” (238mm

x (238mm) side outlet wall plate over outer boot, pass the outer

boot through the wall and attach side wall plate to furnace side

of wall with (2) #10 x 1 1/2” (38mm) provided screws.

5. Attach outer boot to the cabinet side with (4) #8 x 1/4” (6mm)

provided screws.

6. Position and attach inner boot to inner shield with (4) #8 x

1/4” (6mm) provided screws.

7. Place the register over the 6 3/4” (171mm) square opening with

the louvers positioned for the desired discharge direction and

mark the mounting holes using the register as a template.

Drill (2) 1/8” (3mm) diameter holes in the wall and attach the

9. Installation of SOK-1 is completed.

4” MINIMUM TO COMBUSTIBLE

WALL OR SURFACE

VENT

TERMINA

4” MINIMUM TO COMBUSTIBLE

WALL OR SURFACE

18” MIN. CLEARANCE T

WALL OR COMBUSTIBLE

SURFACE USING MODEL

SOR-1 SIDE REGISTER

½”

12”

CLEARANCE FOR SIDE OUTLET KITS T

O ADJACENT WALL

UNIT CANNOT BE RECESSED

WHEN SIDE REGISTERS ARE

USED.

WHEN SIDE REGISTERS ARE

NOT USED, UNIT MAY

BE RECESSED

UP TO

9 1/2”

Figure 5

Figure 6

12430-11-1008Page 10

Locating Electric Supply

A 7/8” (22mm) diameter knockout is provided at the bottom of

the left and right side panels. A three-prong (grounding) plug as-

sembly is located within the control compartment (bottom) of the

furnace. Please remove 7/8” (22mm) knockout from appropriate

side panel when routing plug assembly to an electrical outlet. Unit

can be hard wired when recessed. Remove the 3 prong plug as-

sembly and terminate inside the unit junction box.

Figure 7

Installation of Three-prong (Grounding) Plug Assembly

1. Disconnect nylon cap on 3’ (92cm) plug assembly from nylon

plug on wiring harness. Remove 3’ (92cm) plug assembly

from control compartment (bottom) of the furnace.

Remove 7/8” (22mm) knockout from appropriate side

panel.

3. Insert nylon cap on 3’ (92cm) plug assembly into the 7/8”

(22mm) hole in the side panel.

4. Connect nylon cap on 3’ (92cm) plug assembly to nylon plug

on the wiring harness.

5. Place 7/8” (22mm) strain relief bushing around the cord of

the 3’ (92cm) plug assembly. Insert 7/8” (22mm) strain relief

bushing into the 7/8” (22mm) hole in the side panel.

Attention! The 7/8” (22mm) strain relief bushing is located within

the same envelope as the Installation Instructions and Owner’s

Manual.

Attaching Furnace to Wall

Refer to Figure 5 for the location of the 7 1/2” (191mm) diam-

eter wall opening for the furnace. After the wall opening has been

located and cut, position ﬂue outlet on furnace in center of wall

opening. When attaching furnace to the wall, remove that por-

tion of baseboard and molding on the wall which is behind the

furnace. Attach furnace to wall, at the outer casing top, with (2)

toggle bolts provided and to ﬂoor, at the out casing bottom, with

(2) #10 x 1 1/2” (38mm) screws provided.

Cutting Vent Tubes

This is the most important part of the installation. With the fur-

nace installed on the wall, the 6” (152mm) diameter inlet tube and

the 4” (102mm) diameter ﬂue outlet tube are to be marked and cut

using the following procedure.

1. Attach 6” (152mm) diameter air inlet tube onto the collar

of air drop assembly. Be sure 6” (152mm) diameter air inlet

tube is placed as far as possible onto the collar of the air

drop assembly. Mark the 6” (152mm) diameter air inlet tube

1/2” (13mm) beyond the outside wall. Remove 6” (152mm)

diameter air inlet tube from collar of air drop assembly.

2. Attach 4” (102mm) diameter ﬂue outlet tube onto ﬂue outlet

collar on combustion chamber. Be sure 4” (102mm) diameter

ﬂue outlet tube is placed as far as possible onto the collar of

ﬂue outlet. Mark the 4” (102mm) diameter ﬂue outlet tube 2

1/4” (57mm beyond the outside wall. Remove 4” (102mm)

diameter ﬂue outlet tube from collar of ﬂue outlet on combus-

tion chamber

3. Mark or wrap tape completely around the tubes at the marked

points to help in making a true cut. Do not crimp or enlarge

tubes.

Installing Vent Assembly (See Figure 8)

1. Place provided caulking beneath the edge of the outside

mounting plate. Use additional caulking to correct uneven

wall surface, such as clapboard.

2. Attach 6” (152mm) diameter air inlet tube onto the collar of

air drop assembly. Attach caulked, outside mounting plate into

the 6” (152mm) diameter air inlet tube. Position the outside

mounting plate so that 6” (152mm) diameter air inlet tube

has a slight downward slope to the outside. The downward

slope is necessary to prevent the entry of rainwater. Attach

outside mounting plate to exterior wall with (4) #10 x 1 1/2”

(38mm) screws provided.

3. Apply furnace cement or RTV silicone sealant to 4” (102mm)

diameter ﬂue outlet collar on combustion chamber and to 4”

(102mm) diameter collar on vent cap. Attach 4” (102mm)

diameter ﬂue outlet tube onto ﬂue outlet collar on combustion

chamber. Attach vent cap into the 4” (102mm) diameter ﬂue

outlet tube. Attach vent cap to outside mounting plate with

(3) #10 x 1/2” (13mm) screws provided.

4. Installation is complete.

Figure 8

12430-11-1008 Page 11

Reassembly and Resealing Vent-Air Intake System

When vent-air intake system is removed for servicing the furnace,

the following steps will assure proper reassembly and resealing of

the vent-air intake assembly.

1. Remove old caulking beneath the edge of the outside mount-

ing plate. Apply new caulking beneath the edge of the outside

mounting plate. Use additional caulking to correct uneven wall

surface, such as clapboard.

2. Remove old furnace sealant from ﬂue outlet collar on com-

bustion chamber and collar of vent cap. Remove old furnace

sealant from both ends of 4” (102mm) diameter ﬂue outlet

tube.

3. Attach 6” (152mm) diameter air inlet tube onto the collar of

air drop assembly. Attach caulked, outside mounting plate into

the 6” (152mm) diameter air inlet tube. Position the outside

mounting plate so that 6” (152mm) diameter air inlet tube has

a slight downward slope to the outside. The downward slope

is necessary to prevent the entry of rainwater. Attach outside

mounting plate to exterior wall with (4) #10 x 1 1/2” (38mm)

screws provided.

4. Apply furnace cement or RTV silicone sealant to 4” (102mm)

diameter ﬂue outlet collar on combustion chamber and to 4”

(102mm) diameter collar on vent cap. Attach 4” (102mm)

diameter ﬂue outlet tube onto ﬂue outlet collar on combustion

chamber. Attach vent cap into the 4” diameter ﬂue outlet tube.

Attach vent cap to outside mounting plate with (3) #10 x 1/2”

(13mm) screws provided.

5. Reassembly and resealing vent-air intake system is com-

pleted.

Installing a Vent Near a Window Ledge,

Other Type of project or on Siding (vinyl, aluminum, etc.)

Direct vent furnaces are designed to be installed on a uniform

outside wall. When the wind comes from any angle (up, down, or

from either side), it must hit the vent cap equally over both the air

inlet and the ﬂue outlet portions of the vent. Any wall projection,

such as a door or window casing, which disturbs the wind on one

side of the air inlet section will result in back pressure on the ﬂue

section smothering the ﬂame and eventual pilot outage.

When the vent cap is to be installed on siding or it appears that a

projection within 6” (152mm) of any side of the air inlet section

could shield the air inlet section, the entire vent should be sup-

ported away from the wall at least the distance of the projection. 2”

x 4” (51mm x 102mm) framing whose outside dimensions match

the overall dimensions of the mounting plate is recommended.

The 2” x 4” (51mm x 102mm) framing protects siding from pos-

sible warpage or discoloration. All joints can then be sealed and

painted. The wall depth plus the additional depth of the 2” x 4”

(51mm x 102mm) framing should not exceed a total depth of 10”

(254mm) for DVC-35 (See Figure 9). If it does, you will need to

use the DV-1190 Extended Flue Kit.

INSTALLATION INSTRUCTIONS (continued)

Vinyl siding kit, DV-822, is available from Empire Comfort Sys-

tems, Inc. The depth is 3” (76mm), which enables the vent cap to

be extended away from siding or projections. The wall depth plus

the additional 3” (76mm) depth of the vinyl siding vent cap exten-

sion should not exceed a total depth of 10” (254mm) for DVC-35

(See Figure 10).

Warning: When vinyl siding vent kit, DV-822 or 2” x 4”

(51mm x 102mm) framing is added to an existing instal-

lation

(furnace is installed) do not attempt to add sections

of pipe to the ﬂue outlet tube or air inlet tube. An air tight

seal is required for both tubes. Refer to Parts List, page 20

to order tubes.

Figure 9 Figure 10

12430-11-1008Page 12

DVC-35 SPP STANDING PILOT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁre or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by

hand. When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the ﬂoor because some gas

is heavier than air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electrical switch;

do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s

phone, Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the ﬁre

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or turn

by hand, don’t try to repair it; call a qualiﬁed service

technician. Force or attempted repair may result in a ﬁre

or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1. STOP! Read safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. Remove control access panel (lower front panel).

5. Turn gas control knob clockwise to “OFF.”

6. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the ﬂoor. If you smell gas, STOP!

Follow “B” in the safety information above. If you don’t

smell gas, go to the next step.

7. Remove the pilot access cover located on the combustion

chamber.

8. Find pilot - follow metal

tube from gas control. The

pilot is located between the

two burner tubes behind the

pilot access cover.

9. Turn gas control knob counterclockwise

to “Pilot.”

10. Push and hold red reset button down completely and

repeatedly push the ignitor button until the pilot burner

is lit. Pilot may also be lit with a match. Continue to hold

the red rest button down for about one (1) minute after

the pilot is lit. Release button and it will pop back up. Pi-

lot should remain lit. If it goes out, repeat step 5 through

10.

• If button does not pup up when released, stop and

immediately call a qualiﬁed service technician or gas

supplier.

• If the pilot will not stay lit after several tries, turn

the gas control knob to “OFF” and call your service

technician or gas supplier.

11. Replace pilot access cover.

12. Turn gas control knob counterclockwise

to “ON.”

13. Replace control access panel (lower front panel).

14. Turn on all electric power to the appliance.

15. Set thermostat to desired setting.

GAS CONTROL KNOB SHOWN IN “OFF” POSITION

THERMOCOUPLE

PILOT BURNER

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to appliance if service is to be

performed.

3. Remove control access panel (lower front panel).

4. Push in gas control knob slightly and turn clockwise

to “OFF.” Do not force.

5. Replace control access panel (lower front panel).

12430-11-1008 Page 13

DVC-35IP INTERMITTENT PILOT LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁre or explosion may result

causing property damage, personal injury or loss of life.

A. T h i s a p p l i a n c e is e q u i p p e d w i t h a n i g n i-

tion device which automatically lights the pilot.

Do NOT try to light the pilot by hand.

B. BEFORE LIGHTING smell all around the appliance area

for gas. Be sure to smell next to the ﬂoor because some gas

is heavier than air and will settle on the ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone, Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁre de-

partment.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or turn

by hand, don’t try to repair it; call a qualiﬁed service

technician. Force or attempted repair may result in a ﬁre

or explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualiﬁed service technician to inspect

the appliance and to replace any part of the control system

and any gas control which has been under water.

OPERATING INSTRUCTIONS

1. STOP! Read safety information above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. This appliance is equipped with an ignition device which

automatically lights the pilot. Do not try to light the pilot

by hand.

HONEYWELL IP SMART VALVE

5. Remove front panel door.

6. Slide gas control switch to “OFF.”

7. Wait ten (10) minutes to clear out any gas. Then smell

for gas, including near the ﬂoor. If you smell gas, STOP!

Follow “B” in the safety information above. If you don’t

smell gas, go to the next step.

8. Slide gas control switch to “ON.”

9. Replace front panel door.

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

12. If the appliance will not operate, follow the instructions,

“TO TURN OFF GAS TO APPLIANCE” and call your

service technician or gas supplier.

IGNITOR

CONTROL

OFF

GAS FLOW

GAS VALVE SHOWN IN OFF POSITION

TO TURN OFF GAS TO APPLIANCE

1. Set the thermostat to lowest setting.

2. Turn off all electric power to the appliance if service is to

be performed.

3. Remove front panel door.

4. Slide gas control switch to “OFF.”

5. Replace front panel door.

12430-11-1008Page 14

PILOT FLAME CHARACTERISTICS

The correct pilot ﬂame (Figure 11) will be blue, extending past

the thermocouple. The ﬂame will surround the thermocouple just

below the tip.

Natural gas pilots require adjusting when the inlet gas pressure is

above 5” w.c. (1.245kPa). Remove the pilot cover screw on the

control valve (Figure 3), and turn the adjustment screw clockwise

to reduce ﬂame. Replace pilot cover screw to eliminate gas leak-

ing at that control valve opening.

LP gas (Propane) will not require adjustment.

After use, cleaning may be required for the proper ﬂame.

IP-Model Pilot

This heater is using a Honeywell “Smart Valve” system for inter-

mittent pilot ignition.

On a call for heat by the thermostat, this control turns on a 24 volt

mini hot surface ignitor which lights a pilot that in turn lights the

main burner. The gas valve used in this system is a step opening

which opens at a lower pressure for ignition and then steps to a

full inlet pressure of 4” H

O pressure on Natural gas and 10” H

pressure on LP gas.

Pilot Flame Adjustment

The pilot ﬂame should envelop 3/8 to 1/2 inch (10 to 13mm) of

the tip of the ﬂame rod. See Figure 11.

To adjust:

1. Remove the pilot adjustment cover screw.

2. Turn the inner adjustment screw clockwise

to decrease or counterclockwise t o

increase pilot ﬂame. Pilot adjustment is shipped at full ﬂow

rate. Turn the inner adjustment screw clockwise

if the inlet pressure is too high.

3. Replace the cover screw after the adjustment to prevent gas

leakage.

THERMOCOUPLE

BURNER

SPARK

ELECTRODE

PILOT

STANDING PILOT

THERMOCOUPLE

PILOT SHIELD

SPARK

ELECTRODE

PILOT LOCATION END VIEW

STANDING PILOT SHOWN

3/8” TO 1/2”

PILOT FLAME

GROUND

ELECTRODE

BURNER

PILOT

HOT SURFACE

IGNITOR

FLAME

ROD

IP-MODEL PILOT

Figure 11

12430-11-1008 Page 15

MAIN BURNER FLAME CHARACTERISTICS

The correct ﬂame will be a short, blue inner ﬂame with a much

larger, light blue, outer ﬂame. The burner does not have a primary

air adjustment. The ﬂame will be correct if the factory-set pressure

and oriﬁce opening are used. After the furnace has been operating,

the burner ports may be blocked by foreign matter carried in by

combustion air. Therefore, cleaning of the burner may be needed

for proper ﬂame.

The clean burner port disconnect the gas supply to the valve, and

remove the screws fastening the burner. After removing the burner

door from the burner box, remove each main burner. Pilot mount-

ing bracket will need to be unscrewed and moved out the way to

remove all burners. Burners can be blown out using compressed

air or by blowing through them. Be sure there is no lint or foreign

debris blocking the burner ports. Reassemble using the same screws

earlier removed and locate pilot in the same position as before and

noted above.

Figure 12

WIRING

The appliance, when installed, must be electrically grounded in ac-

cordance with local codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1, if an external electrical source is utilized. This

appliance is equipped with three-prong (grounding) plug for

your protection against shock hazard and should be plugged

directly into a properly grounded three-prong receptacle. Do

not cut or remove the grounding prong from this plug. For an

ungrounded receptacle, an adapter, which has two prongs and a

wire for grounding, can be purchased, plugged into the ungrounded

receptacle and its wire connected to the receptacle mounting screw.

With this wire completing the ground, the appliance cord plug can

be plugged into the adapter and be electrically grounded. A 7/8”

hole is provided in the junction box for use with a conduit connector

if local codes require this type of protection.

Thermostat Installation

The thermostat should be installed in the same room as the furnace

4’ to 5’ above the ﬂoor and away from another heat source (cooking

stove, hot water heater, etc.) including walls and doorways with

a heat source in an adjoining room. Do Not Install Thermostat

on Outside Wall.

CAUTION: Label all wires prior to disconnection when ser-

vicing

controls. Wiring errors can cause improper and danger-

ous operation. Verify proper operation after servicing.

Figure 13

12430-11-1008Page 16

GAS FLOW

OFF

CONTROL

IGNI

TOR

PRESSURE REGULATOR

ADJUSTMENT-UNDER CAP

SCREW

INLET PRESSURE T

OUTLET PRESSURE TAP

PILOT ADJUSTMENT-

UNDER CAP SCREW

PILOT OUTLET

WIRING

O 24 V. THERMOSAT

O 24 V

. COMMON ON TRANSFORMER

TO 24 V. “HOT” ON TRANSFORMER

IGNITOR-PILOT ASSY.

IP-MODEL GAS V

ALVE AND WIRING

L2 NEUTRAL

L1 “HOT”

120 V

MOTOR

FAN

SWITCH

120VAC

40 V

A TRANSFORMER

24VAC

VALVE CONTROL

CONNECTOR

HONEYWELL IP

SMART

VALVE

THERMOSTA

VENT SAFETY

LIMIT

CONTROL

IGNI

TOR

LADDER WIRING DIAGRAM

Figure 14

Figure 15

12430-11-1008 Page 17

SERVICE AND MAINTENANCE SUGGESTIONS

GENERAL: All furnaces have been ﬁre-tested to check for proper

operation. This includes, main burner ﬂame, pilot ﬂame, fan opera-

tion, fan control, limit control and automatic valve operation. If

the furnace fails to function on initial installation, it is advisable

to re-check the following:

1. 115 volts to the junction box.

2. Inlet gas pressure.

3. The 24 volt system.

4. Type of gas being used and that shown on the rating label.

The Service Department at Empire Comfort Systems, Inc. may be

contacted to assist in servicing furnace.

Standing Pilot Model

Servicing the Pilot and Main Burners, Pilot Oriﬁce, Thermo-

couple, and Main Burner Oriﬁces: Disconnect the gas supply at

the inlet to the control valve. Then remove the burner door to gain

access to the above listed components.

Spark Igniter Does Not Light Pilot: With air in the gas line, such

as when the furnace is ﬁrst installed or was off all summer, the

pilot ﬂame may be too lean to ignite on the ﬁrst few trials. Turn the

control valve knob to pilot position and depress the red reset button.

Holding the button down continually to bleed the line;

1. Use lighter rod to light pilot with a match

2. Use the piezo ignitor at 30 second intervals until it lights.

If Electrode Does Not Produce Spark:

1. Check wire connections.

2. Check gap for pilot burner to the electrode tip. Should be

between 1/8” (3mm) and 3/16” (4.8mm). Electrode wire and

tip must be more than 1/4” (6.3mm) away from all other metal

components.

If Pilot Does Not Light By Any Means:

1. Check valve knob for being in the “Pilot” position.

2. Check pilot adjustment for being full open (counterclockwise

to open).

3. If gas is available in the supply tubing, the pilot oriﬁce and/or

pilot burner is probably restricted by a spider web. Clean pilot

assembly and relight.

If Pilot Does Not Remain On After Releasing Knob:

1. Follow instructions and hold button down longer and hard-

2. Determine if pilot ﬂame extends past thermocouple; if not,

adjust input or clean pilot burner.

3. Replace thermocouple if millivolts read less than 15 mil-

livolts.

Pilot Outage During Normal Operation:

1. Check air inlet tube for a good tight ﬁt at both ends (6” diameter

tube).

2. Check burner door and pilot hole cover for tight seal.

3. Check input by manifold pressure gauge or gas meter.

Main Gas Valve Does Not Open when Thermostat Is Turned

To On:

1. Check for 24 volts to valve by removing one wire and touching

to the SAME TERMINAL it was on. Terminal should have

a light spark. DO NOT SHORT ACROSS TERMINALS,

AS IT WILL BURN OUT THE WALL THERMOSTAT.

2. Thermostat wires at the wall may be shorted, so check for a

faulty thermostat.

3. To check for line voltage to furnace, remove front panel and

short across two-terminal fan control to allow fan to operate

(Figure 14).

Cleaning Combustion (Exchanger) Assembly

A QUALIFIED SERVICE PERSON should remove the combustion

(exchanger) assembly and ﬂue bafﬂes. Apply air pressure to the

inside of the combustion (exchanger) assembly and ﬂue bafﬂes in

order to clear all passageways.

Oiling the Motor

The Fan motor should be cleaned and oiled once each heating

season. Oil holes are located on the top at each end of the motor.

Use a few drops of #10 motor oil. To clean the motor, blow air

through its ventilation openings with a vacuum cleaner or low

pressure air source.

12430-11-1008Page 18

DVC-35IP INTERMITTENT PILOT SEQUENCE OF OPERATION

START

System Check

Trial for

Ignition

Main Burner

Operation

END



Pilot Valve Opens

Ignitor Powered

Flame Signal

Detected

Thermostat

Calls for Heat



Ignitor OFF

Main Valve Opens

Internal Check

Pilot Light and Flame is

Sensed During Trial For

Ignition (1)

Apply 24 VAC

To Appliance

Main Pilot Valves

Thermostat Call for Heat

Ends

Flame Signal

Lost?



Pilot Valve Ignition OFF

Wait for Flame Signal to

Disappear



Pilot Valve Closes

Ignition OFF

Main Pilot

Valves Close

Flame Lost More

Than 5 Times in

One Call for Heat

5 Minute Retry Delay

3 Second Flame Recycle

Delay

YES

(1) Ignitor will turn OFF about 30 seconds into the trial for ignition if the pilot ﬂame has not lit. It will turn back ON for the ﬁnal 30 seconds of

the 90 second trial for ignition. The pilot will be energized during the entire trial for ignition. This is normal operation for this gas ignition

system.

12430-11-1008 Page 19

DVC-35IP INTERMITTENT PILOT SYSTEM TROUBLESHOOTING SEQUENCE

START

IP SYSTEM TROUBLESHOOTING SEQUENCE

Turn OFF Gas Supply

Disconnect System Control

Harness

Set Thermostat to Call for

Heat

Check for Proper Voltage at

Control Harness (See Inset A -

Voltage Should be 2

Between Thermostat and 24V

Common, and 24V Between

24V Common and 24V Hot.)

Plug Harness into SmartValve

Control

Wait for Internal Check Delay

(SV9501)

Igniter Warms UP and Glows

Red

Note: Igniter Will Cycle OFF

and Back ON Once During the

90 Second Ignition Trial

Turn On Gas Supply

Pilot Burner Lights

Main Valve Opens and

Main Burner Lights

System is Okay

Check

Line Voltage Power

Low Voltage Transformer

Limit Controller

Thermostat

Wiring

Unplug Pilot Burner Cable.

Measure Voltage at SmartValue HSI

Element Output (See Inset B) 24V

Nominal

Replace Igniter/Flame Rod

Assembly

Reconnect Pilot Burner Cable

Check that Pilot Gas is Flowing

Wait to Assure Pilot Gas Tubing is

Purged.

Measure Voltage Between 24V Hot

and 24V Common Leads to

SmartValve Control. Must Measure

at Least 19.5 V

AC with Igniter

Powered. See Inse

t A to Identify

Proper Lead. This Check Must be

Done with the SmartValve Control

Connected and Igniter Powered.

Replace Igniter/Flame Rod

Assembly

Check that Pilot Flame Makes

Good Contact with Pilot Burner

Flame Rod

Check for Good Electrical

Connection Through the Pilot

Tubing

If Both of the Above are Good,

Replace Igniter/Flame Rod

Cycle Thermostat OFF and Back

Main Burner Lights

YES

Replace SmartValve Control

Reconnect Pilot Burner Cable

Replace SmartValve Control

Check Transformer and Line Volt

Supply

Replace SmartValve Control

SmartValve System Troubleshooting Sequence

Note: Before Troubleshooting, Become Familiar

with the Sequence of Operation

INSET A

24 Volt

Thermostat

Volts

24 Volt

Common

Volts

24 Volt

Hot

EFT

Output

End View

of Control

Harness

Connector

INSET B

HSI

Terminals

12430-11-1008Page 20

HOW TO ORDER REPAIR PARTS

Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts

through the distributor. Parts can be shipped directly to the service person/dealer.

All parts listed in the Parts List have a Part Number. When ordering parts, ﬁrst obtain the Model Number from the name plate on your

equipment. Then determine the Part Number (not the Index Number) and the Description of each part from the following appropriate

illustration and list. Be sure to give all this information...

Furnace Model Number Part Description

Furnace Serial Number Part Number

Type of Gas (Propane or Natural)

Do not order bolts, screws, washers or nuts. They are standard hardware items and can be purchased at any local hardware store. Ship-

ments contingent upon strikes, ﬁres and all causes beyond our control.

Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, IL 62222-0529

PARTS LIST

PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide.

INDEX

NO.

ART

NUMBER DESCRIPTION

INDEX

NO.

PART

NUMBER DESCRIPTION

1 DV-1213 TOP PLATE 34 DV-781 OBSERVATION HOLE COVER WITH MICA

2 R-3165 DOOR CLIP

(2 REQUIRED) 35 M-155 GASKET - OBS HOLE

3 DV

-1204 CASING SIDE - RIGHT 36 FF-160 PIEZO BRACKET (SPP ONLY)

4 DV

-1202 CASING BACK 37 DV-1240 BURNER COMPARTMENT FRONT

5 DV

-1205 CASING SIDE - LEFT 38 DV-12655 BURNER COMPARTMENT BODY

6 DV

-1249 AIR DROP 39 712059 GASKET - TUBE SEAL

7 DV

-1230 TURBULATOR (3 REQUIRED) 40 DV-775 SEAL BRACKET (SPP ONLY)

8 DV

-1233 OUTLET BOX REAR 40 DV-691 SEAL BRACKET (IP ONLY)

9 DV

-1224 OUTLET BOX COVER 41 M-156 MANIFOLD GASKET

10 R-3161 F

AN BLADE 42 DV-1235 PILOT BRACKET (IP ONLY)

11 R-3166 F

AN MOTOR 43 R-3031 BURNER (3 REQUIRED)

12 DV

-1246 MOTOR MOUNTING BRACKET 44 DV-1239 BURNER BRACKET

13 R-1536 BUSHING 45 UH-810 TRANSFORMER MOUNTING BRACKET

(SPP ONLY)

14 R-1499 RUBBER GROMMET

(4 REQUIRED) 45 UH-452 TRANSFORMER MOUNTING BRACKET (IP ONLY)

15 R-1454 BRASS BUSHING (4 REQUIRED) 46 R-1995 TRANSFORMER (SPP

ONLY)

16 R-3164 DOOR CLIP

(2 REQUIRED) 46 R-998 TRANSFORMER (IP ONLY)

17 DV

-1251 INNER SHIELD - RIGHT (INCLUDES NO. 22) 47 UH-451 JUNCTION BOX COVER

18 R-6176 F

AN CONTROL SWITCH 48 DV-572 JUNCTION BOX

19 R-3175 LIMIT

SWITCH 49 R-1410 BUSHING

20 DV

-1255 INNER SHIELD FRONT (USA) 50 R-690 CORD SET

20 15666 INNER FRONT

ASSEMBLY (CANADA) 51 R-1515 BUSHING

21 DV

-1253 INNER SHIELD COVER PLATE (2 REQUIRED) 52 DV-1215 BOTTOM PLATE

22 DV

-1252 INNER SHIELD - LEFT (INCLUDES NO. 22) 53 R-3034 PILOT - NAT (SPP ONLY)

23 DV

-1257 EXCHANGER ASSEMBLY 53 R-3035 PILOT - LPG (SPP ONLY)

24 R-3162 FIL

TER 54 GWT-021 PILOT BRACKET (SPP ONLY)

25 R-3163 FIL

TER RETAINER 55 R-3180 ELECTRODE AND WIRE (SPP ONLY)

26 R-3232 PILOT

- NAT (IP ONLY) 56 R-2256 THERMOCOUPLE - 18” (SPP ONLY)

26 R-3233 PILOT

- LPG (IP ONLY) 57 R-6389 WALL THERMOSTAT - 24 VOLT

27 P-88-61 ORIFICE - NA

T (3 REQUIRED) 58 DV-1273 VENT KIT COMPLETE

27 P-88-61C ORIFICE - LPG (3 REQUIRED) 59 DV

-1355 FLUE OUTLET TUBE

28 DV

-1236 MANIFOLD 60 DV-1354 AIR INLET TUBE

29 DV

-1259 FRONT PANEL 61 DV-131 OUTSIDE MOUNTING PLATE

30 P-1

12 MANIFOLD UNION 62 DV-769 VENT CAP

31 R-1

109 BUSHING (3/8 X 1/2) NOT SHOWN DV-1261 PILOT TUBING

31 R-9505 BUSHING (1/2 X 3/4) - NA

T (IP ONLY) NOT SHOWN R-1081 PILOT ORIFICE - NAT (SPP ONLY)

32 R-3170 GAS

VALVE - NAT (IP ONLY) NOT SHOWN R-1089 PILOT ORIFICE - LPG (SPP ONLY)

32 R-3171 GAS

VALVE - LPG (IP ONLY) NOT SHOWN R-1233 PILOT ORIFICE - NAT (IP ONLY)

32 R-2148 GAS

VALVE - NAT (SSP ONLY) NOT SHOWN R-3265 PILOT ORIFICE - LPG (IP ONLY)

32 R-5655 GAS

VALVE - LPG (SPP ONLY) NOT SHOWN R-3172 WIRE HARNESS (SPP ONLY)

33 R-2708 PIEZO IGNITOR (SPP ONLY)

NOT SHOWN R-3173 WIRE HARNESS (IP

ONLY)

NOT SHOWN R-3236 WIRE (IP

ONLY)

USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH.

Page is loading ...

Empire DVC-35-SPP Owner's manual

Brand: Empire

Model: DVC-35-SPP

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Empire DVC-35-SPP Owner's manual

This manual is also suitable for

Empire DVC-35-SPP Owner's manual

Related papers

Other documents